2AXGD-C031Dreame Floor Lamp F11P

Rev 1/26/2023 (Dreame Trading (Tianjin) Co., Ltd.) Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2026-01-19 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AXGD-C031 Dreame Trading (Tianjin) Co., Ltd. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Dreame Trading (Tianjin) Co., Ltd. (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, William Chen/Certification Engineer Rev 1/26/2023 (Dreame Trading (Tianjin) Co., Ltd.) Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2026-01-19 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AXGD-C031 Dreame Trading (Tianjin) Co., Ltd. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, William Chen/Certification Engineer

Dreame Trading (Tianjin) Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Date: 2026-1-26 SUBJECT: FCC ID: 2AXGD-C031 To Whom It May Concern: I, the undersigned, hereby states this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, and will apply the Supplier's Declaration of Conformity procedure to the class B computer peripheral portion of this composite device. I understand the following FCC requirements: 1. Devices subject to the SDoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage: https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm (Select the "accredited" option to search for FCC recognized accredited test firms.) 2. Pt 2.1077 contains the list of information that must be included in the Supplier's Declaration of Conformity, which must be supplied with each product sold. The SDoC compliance info shall be included in the User’s Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible party, which must be located within the United States. According to 2.909(b), the responsible party is either the Manufacturer or if the product is imported the Importer. Regards, Dreame Trading (Tianjin) Co., Ltd. ------------------------------- William Chen/Certification Engineer

CFR 47 §2.911(d)(7) U.S Agent U.S. AGENT LETTER OF ATTESTATION Signed by (printed name): Shirley Kwok Signature: Applicant: Dreame Trading ሺTianjinሻ Co.,Ltd. Add: Room 2112-1-1 South District Finance and Trade Center No.6975 Yazhou Road Dongjiang Bonded Port Area Tianjin China FRN: 0029939097 Tel: 13451734209 Email: [email protected] Signed by (printed name): William Chen Signature: Date: 2026-01-04 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: 2AXGD-C031 Dreame Trading (Tianjin) Co.,Ltd. (“the Applicant”) certifies that, as of the date of the filing of the application, ANTEK SERVICE INC(U.S. agent). is our designated U.S. agent for service of process for the above referenced FCC ID. Dreame Trading (Tianjin) Co.,Ltd. (“the Applicant”) accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. ANTEK SERVICE INC (U.S. agent) accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: ANTEK SERVICE INC Address: 901 N PENNSYLVANIA ST STE 0 DENVER, CO 80203 United States FRN: 0033437609 Tel.: (303) 800-6306 Email: [email protected]

(Dreame Trading (Tianjin) Co., Ltd.) Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AXGD-C031 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Block Diagram, Schematics, Operational Description Block Diagram .pdf, Schematics .pdf , Operation Description .pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below: Short-term confidentiality requested: 180 days Exhibit Type File Name External Photos, Internal Photos, Test Setup Photos, User Manual External Photos.pdf, Internal Photos .pdf, Test Setup Photos .pdf, User Manual.pdf Sincerely, William Chen/Certification Engineer Dreame Trading (Tianjin) Co., Ltd.

DreameTrading(Tianjin)Co.,Ltd. Tel:13451734209Fax:0512-67074287 Email:[email protected] AuthorizationStatement Duetoworkrequirements,IherebyentrustWilliamChentobefully responsiblefortheproceduresrelatedtoFCCandICcertificationsofcameras, locks,lighting,andtheirperipheralproducts,aswellasthesigningofrelevant documentsduringthecertificationprocess. Principal:JoyceMo Signature: Date:2025/09/28 DreameTrading(Tianjin)Co.,Ltd.

(DreameTrading(Tianjin)Co.,Ltd.) FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 Date:2026-01-16 SUBJECT:FCCApplicationforFCCID:2AXGD-C031 ToWhomItMayConcern: We,theundersigned,herebyauthorizeLucasXuatDEKRATestingandCertification (Shanghai)Ltd.onourbehalf,toapplytotheFederalCommunicationsCommissiononour equipment.AnyandallactscarriedoutbyDEKRATestingandCertification(Shanghai) Ltd.onourbehalfshallhavethesameeffectasactsofourown. ThisistoadvisethatweareinfullcompliancewiththeAnti-DrugAbuseAct.We,the applicant,arenotsubjecttoadenialoffederalbenefitspursuanttoSection5301ofthe Anti-DrugActof1988,21USC853a,andnopartytotheapplicationissubjecttoadenial offederalbenefitspursuanttothatsection. Regards, WilliamChen/CertificationEngineer DreameTrading(Tianjin)Co.,Ltd.

Label and Label Location Location

DEKRA Testing and Certification (Shanghai) Ltd. No.250,Jiangchangsan Road, Shanghai ,200436 P.R.China www.dekra.com Test report No: 6252518.52 ASSESSMENT REPORT RF Exposure Evaluation Identification of item tested Dreame Floor Lamp F11P Trademark N/A Model and /or type reference C031 Features Adapter: Input: AC 100-240 V, 50/60 Hz, 1.0 A Max Output: DC 12.0 V, 2.0 A FCC ID 2AXGD-C031 ISED Number 26444-C031 Applicant ́s name / address Dreame Trading (Tianjin) Co., Ltd. 2112-1-1, South, Finance and Trade Center, 6975 Yazhou Road, Dongjiang Bonded Port Area, Tianjin Pilot Free Trade Zone, 300463 Tianjin, China Test method requested, standard FCC CFR Title 47 Part 2 Subpart J Section 2.1091 RSS-102 Issue 6 IEEE Std C95.3:2002 Verdict Summary IN COMPLIANCE Prepared by (name / position & signature) Li Wang Test Engineer Approved by (name / position & signature) Lucas Xu Project Engineer Date of issue 2026-01-19 Report template No TRF_MPE_RF01 V1.1 DEKRA Testing and Certification (Shanghai) Ltd. No.250,Jiangchangsan Road, Shanghai ,200436 P.R.China www.dekra.com Report no.: 6252518.52 Page 2 / 9 INDEX page Competences and Guarantees ................................................................................................................................... 3 General conditions ...................................................................................................................................................... 3 Environmental conditions............................................................................................................................................ 3 Possible test case verdicts ......................................................................................................................................... 4 Definition of symbols used in this test report .............................................................................................................. 4 Abbreviations .............................................................................................................................................................. 4 Document History ....................................................................................................................................................... 4 Remarks and Comments ............................................................................................................................................ 5 1 General Information ........................................................................................................................................... 6 1.1 General Description of the Item(s) .......................................................................................................... 6 1.2 Test date ................................................................................................................................................. 7 1.3 Test Facility ............................................................................................................................................. 7 2 Maximum Permissible Exposure (MPE) ............................................................................................................ 8 2.1 Limit ......................................................................................................................................................... 8 2.2 MPE Calculation Method ......................................................................................................................... 9 2.3 Result of MPE for standalone ................................................................................................................. 9 DEKRA Testing and Certification (Shanghai) Ltd. No.250,Jiangchangsan Road, Shanghai ,200436 P.R.China www.dekra.com Report no.: 6252518.52 Page 3 / 9 COMPETENCES AND GUARANTEES DEKRA is a testing laboratory competent to carry out the tests described in this report. In order to assure the traceability to other national and international laboratories, DEKRA has a calibration and maintenance program for its measurement equipment. DEKRA guarantees the reliability of the data presented in this report, which is the result of the measurements and the tests performed to the item under test on the date and under the conditions stated in the report and it is based on the knowledge and technical facilities available at DEKRA at the time of performance of the test. DEKRA is liable to the client for the maintenance of the confidentiality of all information related to the item under test and the results of the test. The results presented in this Test Report apply only to the particular item under test established in this document. IMPORTANT: No parts of this report may be reproduced or quoted out of context, in any form or by any means, except in full, without the previous written permission of DEKRA. GENERAL CONDITIONS 1. This report is only referred to the item that has undergone the test. 2. This report does not constitute or imply on its own an approval of the product by the Certification Bodies or Competent Authorities. 3. This document is only valid if complete; no partial reproduction can be made without previous written permission of DEKRA. 4. This test report cannot be used partially or in full for publicity and/or promotional purposes without previous written permission of DEKRA. 5. The information provided by the customer in this report may affect the validity of the results, the test lab is not responsible for it. 6. This report will not be used for social proof function in China market. ENVIRONMENTAL CONDITIONS The climatic conditions during the tests are within the limits specified by the manufacturer for the operation of the EUT and the test equipment. The climatic conditions during the tests were within the following limits: Ambient temperature 15 °C – 35 °C Relative Humidity air 30% - 60% Atmospheric pressure 86 kPa – 106 kPa If explicitly required in …

Text truncated - open the document above for the full version.

ANTENNASPECIFICATIONS ItemSpecifications Antenna FrequencyRange2400~2483.5MHz PolarizationLinear PeakGain0.91dBi V.S.W.R ＜ 2.0 Impedance50Ω ReturnLoss-10dB ConnectorMicrostriplineconnection Efficiency 25% Type Onboard：ANT0 Size 12.5x6.5mm Manufacturer ShenzhenJingxunTechologyLimited Co.,Ltd Manufactureraddress 3/F,A5BuildingZhiyuanCommunityNo.1001, XueyuanRoad,NanshanDistrict,Shenzhen City,China EnvironmentalOperatingTemperature-40°C~+105°C ANTENNAPATTERN AntennaPicture ：

DEKRA Testing and Certification (Shanghai) Ltd. No.250,Jiangchangsan Road, Shanghai ,200436 P.R.China www.dekra.com Test report No: 6252518.51 TEST REPORT Radio Spectrum Matters (RF) Identification of item tested Dreame Floor Lamp F11P Trademark N/A Model and /or type reference C031 Features Adapter: Input: AC 100-240 V, 50/60 Hz, 1.0 A Max Output: DC 12.0 V, 2.0 A FCC ID 2AXGD-C031 ISED Number 26444-C031 Applicant ́s name / address Dreame Trading (Tianjin) Co., Ltd. 2112-1-1, South, Finance and Trade Center, 6975 Yazhou Road, Dongjiang Bonded Port Area, Tianjin Pilot Free Trade Zone, 300463 Tianjin, China Test method requested, standard FCC CFR Title 47 Part 15 Subpart C Section 15.247 ANSI C63.10-2020+Cor.1-2023+C63.10a-2024+Errata to C63.10a-2024 RSS-Gen Issue 5 RSS-247 Issue 4 Verdict Summary IN COMPLIANCE Prepared by (name / position & signature) Li Wang Test Engineer Approved by (name / position & signature) Lucas Xu Project Engineer Date of issue 2026-01-26 DEKRA Testing and Certification (Shanghai) Ltd. No.250,Jiangchangsan Road, Shanghai ,200436 P.R.China www.dekra.com Report no.: 6252518.51 Page 2 / 59 Report template No TRF_Part15C_247_RF03 V1.2 DEKRA Testing and Certification (Shanghai) Ltd. No.250,Jiangchangsan Road, Shanghai ,200436 P.R.China www.dekra.com Report no.: 6252518.51 Page 3 / 59 INDEX page Competences and Guarantees ................................................................................................................................... 5 General conditions ...................................................................................................................................................... 5 Uncertainty .................................................................................................................................................................. 5 Environmental conditions............................................................................................................................................ 6 Possible test case verdicts ......................................................................................................................................... 6 Definition of symbols used in this test report .............................................................................................................. 6 Abbreviations .............................................................................................................................................................. 6 Document History ....................................................................................................................................................... 7 Remarks and Comments ............................................................................................................................................ 7 1 General Information ........................................................................................................................................... 8 1.1 General Description of the Item(s) .......................................................................................................... 8 1.2 Test date ................................................................................................................................................. 9 2 Description of Test Setup ................................................................................................................................ 10 2.1 Operating mode(s) used for tests.......................................................................................................... 10 2.2 Support / Auxiliary equipment / unit / software for the EUT .................................................................. 10 2.3 Test Configuration / Block diagram used for tests ................................................................................ 10 3 Verdict summary section ................................................................................................................................. 11 3.1 Standards .............................................................................................................................................. 11 3.2 Deviation(s) from the Standard(s) / Test Specification(s) ..................................................................... 11 3.3 Overview of results ................................................................................................................................ 11 3.4 Test Facility ........................................................................................................................................... 12 3.5 Measurement procedure ....................................................................................................................... 12 4 Test Results ..................................................................................................................................................... 13 4.1 AC Power Line Conducted Emission .................................................................................................... 13 4.2 Emissions in restricted frequency bands .............................................................................................. 17 4.3 Emissions in non-restricted frequency band ......................................................................................... 29 4.4 Duty Cycle ............................................................................................................................................. 34 4.5 Radiated Emission Band Edge ............................................................................................................. 35 4.6 DTS Bandwidth & Occupied Bandwidth ................................................................................................ 40 4.7 Fundamental emission output power .................................................................................................... 48…

Text truncated - open the document above for the full version.

DEKRA Testing and Certification (Shanghai) Ltd. No.250,Jiangchangsan Road, Shanghai ,200436 P.R.China www.dekra.com Test report No: 6252518.50 TEST REPORT Radio Spectrum Matters (RF) Identification of item tested Dreame Floor Lamp F11P Trademark N/A Model and /or type reference C031 Features Adapter: Input: AC 100-240 V, 50/60 Hz, 1.0 A Max Output: DC 12.0 V, 2.0 A FCC ID 2AXGD-C031 ISED Number 26444-C031 Applicant ́s name / address Dreame Trading (Tianjin) Co., Ltd. 2112-1-1, South, Finance and Trade Center, 6975 Yazhou Road, Dongjiang Bonded Port Area, Tianjin Pilot Free Trade Zone, 300463 Tianjin, China Test method requested, standard FCC CFR Title 47 Part 15 Subpart C Section 15.247 ANSI C63.10-2020+Cor.1-2023+C63.10a-2024+Errata to C63.10a-2024 RSS-Gen Issue 5 RSS-247 Issue 4 Verdict Summary IN COMPLIANCE Prepared by (name / position & signature) Li Wang Test Engineer Approved by (name / position & signature) Lucas Xu Project Engineer Date of issue 2026-01-26 DEKRA Testing and Certification (Shanghai) Ltd. No.250,Jiangchangsan Road, Shanghai ,200436 P.R.China www.dekra.com Report no.: 6252518.50 Page 2 / 73 Report template No TRF_Part15C_247_RF01 V1.2 DEKRA Testing and Certification (Shanghai) Ltd. No.250,Jiangchangsan Road, Shanghai ,200436 P.R.China www.dekra.com Report no.: 6252518.50 Page 3 / 73 INDEX page Competences and Guarantees ................................................................................................................................... 5 General conditions ...................................................................................................................................................... 5 Uncertainty .................................................................................................................................................................. 5 Environmental conditions............................................................................................................................................ 6 Possible test case verdicts ......................................................................................................................................... 6 Definition of symbols used in this test report .............................................................................................................. 6 Abbreviations .............................................................................................................................................................. 6 Document History ....................................................................................................................................................... 7 Remarks and Comments ............................................................................................................................................ 7 1 General Information ........................................................................................................................................... 8 1.1 General Description of the Item(s) .......................................................................................................... 8 1.2 Test date ................................................................................................................................................. 9 2 Description of Test Setup ................................................................................................................................ 10 2.1 Operating mode(s) used for tests.......................................................................................................... 10 2.2 Support / Auxiliary equipment / unit / software for the EUT .................................................................. 10 2.3 Test Configuration / Block diagram used for tests ................................................................................ 10 3 Verdict summary section ................................................................................................................................. 11 3.1 Standards .............................................................................................................................................. 11 3.2 Deviation(s) from the Standard(s) / Test Specification(s) ..................................................................... 11 3.3 Overview of results ................................................................................................................................ 11 3.4 Test Facility ........................................................................................................................................... 12 3.5 Measurement procedure ....................................................................................................................... 12 4 Test Results ..................................................................................................................................................... 14 4.1 AC Power Line Conducted Emission .................................................................................................... 14 4.2 Emissions in restricted frequency bands .............................................................................................. 17 4.3 Emissions in non-restricted frequency band ......................................................................................... 29 4.4 Duty Cycle ............................................................................................................................................. 38 4.5 Radiated Emission Band Edge ............................................................................................................. 40 4.6 DTS Bandwidth & Occupied Bandwidth ................................................................................................ 45 4.7 Fundamental emission output power .................................................................................................... 59…

Text truncated - open the document above for the full version.