2AXJ4T300Tapo Smart Water Leak Sensor

Quick Start Guide Smart Water Leak Sensor Remove the battery insulation tab to power up your sensor. The LED should blink. 1. Power Up Your Sensor1 The sensor will alarm if you drip water on the sensor probe or place it on a wet surface. 1. Check Your Sensor2 7106509948 REV1.0.0 Images may differ from actual products. Appearance 4 5 3 2 1 Control Button LED 1 Control Button Sensor Probe 3 Sensor Probe Buzzer Battery Compartment Single press Silence alarm; Test connection with the hub. Double press Adjust alarm volume. The volume level cycles through High, Normal, Low, and Mute. Press and hold for 5s Pair with hub. 2 LED Indicator Blinking Blinks once Blinks twice Blinks 3 times Blinks 4 times Enter pairing mode Adjusted alarm volume level to Mute Adjusted alarm volume level to Low Adjusted alarm volume level to Normal Adjusted alarm volume level to High A Tapo Hub is required. Make sure your Tapo Hub’s firmware is updated to the latest version and successfully set up via the Tapo app. Open the Tapo app and tap the button. Select Sensors and then your model. Follow the app instructions to complete setup. OR Tapo App Set Up Your Sensor on the Tapo App3 After setup, single press the control button on your sensor and check if the hub sounds an alarm. 3. Test Your Sensor 4 Place Your Sensor Lay the sensor flat to monitor water leaks. a. Remove the two screws securing the batteries and remove the back cover. b. Replace with the new batteries (AAA/LR03). How to Replace Battery5 Need some help? ? Visit www.tapo.com/support/ for technical support, user guides, FAQs, warranty & more Do not ingest battery, Chemical Burn Hazard Safety Information Keep the device away from fire or hot environments. Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk. TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU) 2015/863. The original EU declaration of conformity may be found at https://www.tapo.com/en/support/ce/ TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017. The original UK declaration of conformity may be found at https://www.tapo.com/support/ukca/ For EU/UK Region: Operating Frequency / Nominal Operating Frequency / Max Output Power: 863~865MHz / 863.35MHz / 25mW (e.r.p) 863~865MHz / 864.35MHz / 25mW (e.r.p) 868~868.6MHz / 868.35MHz / 25mW (e.r.p) ©2023 TP-Link Avoid replacement of a battery with an incorrect type that can defeat a safeguard. Avoid disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion. Do not leave a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; Do not leave a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas. Warning Risk of explosion if the battery is replaced by an incorrect type. Warning Two screws securing batteries Operating Temperature: 0°C (32°F) - 40°C (105°F) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement. Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

TP-Link Corporation Limited CERTIFICATIONS CONCERNING “COVERED” EQUIPMENT Date:2023-04-07 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 FCC ID: 2AXJ4T300 To Whom It May Concern: As required by section 2.911(d)(5)(i), [TP-Link Corporation Limited] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. As required by section 2.911(d)(5)(ii), [TP-Link Corporation Limited] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing “covered” equipment. Thank you for your attention to this matter. Sincerely yours, Signature Printed Name: Sarah Wang Company: TP-Link Corporation Limited Job Title: Regulatory Compliance Manager Email: [email protected] Telephone: 00852-37585503

TP-LinkCorporationLimited 030122-15 AuthoritytoActasAgent Date:April10,2023 AmericanCertificationBody,Inc. 313ParkAvenue Suite300 FallsChurch,VA22046 ToWhomItMayConcern: BTLInc./RoseLiuisauthorizedtoactonourbehalf,untilotherwisenotified,forapplicationsto AmericanCertificationBody,Inc.(ACB). Wecertifythatwearenotsubjecttodenialoffederalbenefits,thatincludesFCCbenefits,pursuantto Section5301oftheAnti-DrugAbuseActof1988,21U.S.C.862.Further,noparty,asdefinedin47 CFR1.2002(b),totheapplicationissubjecttodenialoffederalbenefits,thatincludesFCCbenefits. WealsodeclarethattheinformationprovidedtotheFCCistrueandcorrecttothebestofour knowledge(47CFR2.911(d))andwehavebeeninformedofthegranteeresponsibilities(47CFR 2.909)withregardtocertifiedequipment. Thankyou, AgencyAgreementExpirationDate:2024-04-07 By:__________________________SarahWang (Signature 1 )(Printname) Title:RegulatoryComplianceManager Onbehalfof:TP-LinkCorporationLimited (CompanyName) Telephone:00852-37585503 1 -MustbesignedbyapplicantcontactgivenforapplicantontheFCCsite,orbytheauthorizedagentifanappropriateauthorizedagent letterhasbeenprovided.Lettersshouldbeplacedonappropriateletterhead.

TP-LinkCorporationLimited 030122-15 RequestforConfidentiality Date:April10,2023 Subject:ConfidentialityRequestfor:2AXJ4T300 PursuanttoFCC47CFR0.457(d)and0.459andICRSP-100,Section12.4,theapplicantrequeststhatapartofthe subjectFCCapplicationbeheldconfidential. TypeofConfidentialityRequestedExhibit ☐ShortTerm☒PermanentBlockDiagrams ☐ShortTermExternalPhotos ☐ShortTerm☐Permanent* 1 InternalPhotos ☐ShortTerm☒PermanentOperationDescription/TheoryofOperation ☐ShortTerm☐PermanentPartsList&Placement/BOM ☐ShortTerm☐PermanentTune-UpProcedure ☐ShortTerm☒PermanentSchematics ☐ShortTermTestSetupPhotos ☐ShortTerm☐Permanent* 3 User’sManual TP-LinkCorporationLimitedhasspentsubstantialeffortindevelopingthisproductanditisoneofthefirstofits kindinindustry.Havingthesubjectinformationeasilyavailableto"competition"wouldnegatetheadvantagethey haveachievedbydevelopingthisproduct.Notprotectingthedetailsofthedesignwillresultinfinancialhardship. PermanentConfidentiality: Theapplicantrequeststheexhibitslistedaboveaspermanentlyconfidentialbepermanentlywithheldfrompublic reviewduetomaterialsthatcontaintradesecretsandproprietaryinformationnotcustomarilyreleasedtothepublic. Short-TermConfidentiality: Theapplicantrequeststheexhibitsselectedaboveasshorttermconfidentialbewithheldfrompublicviewfora periodof___(specifynumberofdaysnottoexceed180) 2 ___daysfromthedateoftheGrantofEquipment Authorizationandpriortomarketing.Thisistoavoidprematurereleaseofsensitiveinformationpriortomarketing orreleaseoftheproducttothepublic.ApplicantisalsoawarethattheyareresponsibletonotifyACBintheevent informationregardingtheproductortheproductismadeavailabletothepublicbeforetherequestedperiodhas expired.ACBwillthenreleasethedocumentslistedaboveforpublicdisclosurepursuanttoFCCPublicNoticeDA 04-1705. NOTEforIndustryCanadaApplications: ICcurrentlyonlydistinguishesPermanentConfidentialityexhibitsasshownabove.ShortTermconfidentialityisnot consideredapplicabletoICapplications. Sincerely, By:RegulatoryComplianceManagerSarahWang (Signature/Title 3 )(Printname) 1 -Theasteriskeditems(*)requirefurtherinformationtobeprovidedtoACBbeforepermanentconfidentialitywillbeextendedtothese exhibits.PleaserefertoFCCKDB726920andthespecificDocumentlinkforD01foundat: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731andreviewsectionII,3)regardingspecific informationthatmustaccompanytheserequests. 2 -Pleaserefertohttps://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdfforcompletedetails. 3 -MustbesignedbyapplicantcontactgivenforapplicantontheFCCsite,orbytheauthorizedagentifanappropriateauthorizedagent

DeclarationofConformity We Name:TP-LinkCorporationLimited Address:Room901,9/F.,NewEastOceanCentre,9ScienceMuseumRoad,TsimShaTsui, Kowloon,HongKong Declarethat: Product: TapoSmartWaterLeakSensor FCCID: 2AXJ4T300 Model: TapoT300 Brand:tp-link,tapo ProductwhichbearstheaboveFCCIDisalsocompliantwiththeFCCrequirementsforsDOC. AndthesDOCprocedureshallbecarriedoutpriortomarketingthedeviceintheUS. Sincerely, Name:SarahWang Position:RegulatoryComplianceManager Date:2023-04-07

Global Certification Corp. 報告編號:TR3-351602 日期: 民國112年05月27日 外觀照 廠牌：tp-link、tapo 型號：Tapo T300 02.待測物外觀照-2 01.待測物外觀照-1 1 3 Global Certification Corp. 報告編號:TR3-351602 日期: 民國112年05月27日 外觀照 廠牌：tp-link、tapo 型號：Tapo T300 03.待測物外觀照-3 04.待測物外觀照-4 NCC標籤 2 3 Global Certification Corp. 報告編號:TR3-351602 日期: 民國112年05月27日 外觀照 廠牌：tp-link、tapo 型號：Tapo T300 05.待測物外觀照-5 06.待測物外觀照-6 3 3

Tapo Smart Water Leak Sensor Model: Tapo T300 Power: 3V Tapo T300(EU&US)1.0 深圳市联洲国际技术有限公司 Tapo T300(EU&US)1.0_认证镭雕 A5 胡燕燕 2023.03.13 增加日本认证 Pantone Cool Gray 8C TP-Link Corporation Limited Suite 901, New East Ocean Centre, Tsim Sha Tsui, Hong Kong Batteries: 2x 1.5V SIZE AAA/LR03 FCC ID: 2AXJ4T300 MAC:XX-XX-XX-XX-XX-XX E U/1.0 S/N:XXXXXXXXXXXXX MADE IN CHINA IP67 201- 230144 1.8±0.3mm 2.93±0.3mm 5.43±0.3mm 2.93±0.3mm

Global Certification Corp. 報告編號:TR3-351602 日期: 民國112年05月27 日 內部照 廠牌：tp-link 型號：Tapo T300 01.待測物內部照1 02. 待測物內部照2 Global Certification Corp. 報告編號:TR3-351602 日期: 民國112年05月27 日 內部照 廠牌：tp-link 型號：Tapo T300 03. 待測物PCB (正面) 04. 待測物PCB (背面) Global Certification Corp. 報告編號:TR3-351602 日期: 民國112年05月27 日 內部照 廠牌：tp-link 型號：Tapo T300 05. Piezo Buzzer壓電蜂鳴器 (正面) 06. Piezo Buzzer壓電蜂鳴器 (背面) Global Certification Corp. 報告編號:TR3-351602 日期: 民國112年05月27 日 內部照 廠牌：tp-link 型號：Tapo T300 07. 天線位置 06. RFIC

Global Certification Corp. Date of Issue: May.27.2023 Report No:FR2-351602a Page1/7 RF EXPOSURE REPORT FOR Product Name: Tapo Smart Water Leak Sensor Model :TAPO T300 Trade Name : tp-link、tapo Issued to TP-Link Corporation Limited Room 901, 9/F. , New East Ocean Centre, 9 Science Museum Road, Tsim Sha Tsui, Kowloon, Hong Kong Issued by Global Certification Corp. No.146, Sec. 2, Xiangzhang Rd., Xizhi Dist.,New Taipei City 221, Taiwan (R.O.C.) Note: This test refers exclusively to the test presented test model and sample. This report shall not be reproduced except in full, without the written approval of Global Certification Corporation. This document may be altered or revised by Global Certification Corporation. Personnel only, and shall be noted in the revision section of the document. The decision rule is according to the standard test method and request, that measurement result doesn’t consider uncertainty. Global Certification Corp. Date of Issue: May.27.2023 Report No:FR2-351602a Page2/7 Revision History Revision No. Report Number Issue Date Description Author/ Revised by 1. 351602 FR0-351602 May.27.2023 Original Report Judy Global Certification Corp. Date of Issue: May.27.2023 Report No:FR2-351602a Page3/7 TABLE OF CONTENTS ----------------------------------------------------------------------------------------------------- 3 1. GENERAL INFORMATION ---------------------------------------------------------------------------------------------- 4 1.1 DESCRIPTION OF THE TESTED SAMPLES ------------------------------------------------------------------------------------- 5 2. GENERAL SAR TEST REDUCTION AND EXCLUSION GUIDANCE----------------------------------------- 6 3. MPE CALCULATION METHOD ---------------------------------------------------------------------------------------- 7 3.1 LIMIT ---------------------------------------------------------------------------------------------------------------------- 7 3.2. CACULATION METHOD --------------------------------------------------------------------------------------------------- 7 3.3. CALCULATED RESULT --------------------------------------------------------------------------------------------------- 7 Global Certification Corp. Date of Issue: May.27.2023 Report No:FR2-351602a Page4/7 1. GENERAL INFORMATION Applicant : TP-Link Corporation Limited Address : Room 901, 9/F. , New East Ocean Centre, 9 Science Museum Road, Tsim Sha Tsui, Kowloon, Hong Kong Manufacturer : TP-Link Corporation Limited Address : Room 901, 9/F. , New East Ocean Centre, 9 Science Museum Road, Tsim Sha Tsui, Kowloon, Hong Kong EUT : Tapo Smart Water Leak Sensor Model No. : TAPO T300 Trade Name : tp-link、tapo Model Differences : -- Is here with confirmed to comply with the requirements set out in the FCC Rules and Regulations. The said equipment has been tested and found compliance with the requirement of the relative standards . Test Standard : FCC Title 47 Part 2.1091, KDB 447498 D01 V06 Tested By: Approved by: May.27.2023 May.27.2023 Date Ken Huang, Engineer Date Adam Chou, Manager Designation Number: TW1640 Global Certification Corp. Date of Issue: May.27.2023 Report No:FR2-351602a Page5/7 1.1 DESCRIPTION OF THE TESTED SAMPLES EUT Name : Tapo Smart Water Leak Sensor Model : TAPO T300 FCC ID : 2AXJ4T300 Power From InsideOutside Adaptor Battery Power Supply DC Power Source Support Unit PC Power Rating(Battery) : 3 Vdc Power Rating(Adapter) -- Operate Frequency : Refer to the channel list as described below Basic Spec : Bluetooth Bluetooth LE 802.11b 802.11g 802.11n HT20/HT40 Operate Frequency : 920.9 MHz, 921.7 MHz, 922.3 MHz Number of Channels : 3 Step of Channel : N/A  MHz Modulation Type : GFSK FHSS DSSS CCK OFDM Antenna Quantity : 1Tx/1Rx Antenna Type : IFA Antenna gain : -6.53 dBi EUT Received Date : May.16.2023 EUT Channel List : Channels Frequencies(MHz) 1 920.9 2 921.7 3 922.3 Global Certification Corp. Date of Issue: May.27.2023 Report No:FR2-351602a Page6/7 2. GENERAL SAR TEST REDUCTION AND EXCLUSION GUIDANCE 2.1 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·  [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,21 where  f(GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation22  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2.2 At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following  [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·( f(MHz)/150)] mW, at 100 MHz to 1500 MHz  [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 2.3 At frequencies below 100 MHz, the following may be considered for SAR test exclusion  The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm  The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm  SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Global Certification Corp. Date of Issue: May.27.2023 Report No:FR2-351602a Page7/7 3. MPE CALCULATION METHOD 3.1 LIMIT Limits for Maximum Permissible Exposure Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Powe…

Text truncated - open the document above for the full version.

Global Certification Corp. Date of Issue: May.27.2023 Report No:FR2-351602 Page1/48 FCC Part 15 Subpart C TEST REPORT FOR Product Name: Tapo Smart Water Leak Sensor Model : Tapo T300 Trade Name: tp-link、tapo Issued to TP-Link Corporation Limited Room 901, 9/F. , New East Ocean Centre, 9 Science Museum Road, Tsim Sha Tsui, Kowloon, Hong Kong Issued by Global Certification Corp. No.146, Sec. 2, Xiangzhang Rd., Xizhi Dist.,New Taipei City 221, Taiwan (R.O.C.) Note: This test refers exclusively to the test presented test model and sample. This report shall not be reproduced except in full, without the written approval of Global Certification Corporation. This document may be altered or revised by Global Certification Corporation. Personnel only, and shall be noted in the revision section of the document. The decision rule is according to the standard test method and request, that measurement result doesn’t consider uncertainty. Global Certification Corp. Date of Issue: May.27.2023 Report No:FR2-351602 Page2/48 Revision History Revision No. Report Number Issue Date Description Author/ Revised by 1. 351602 FR2-351602 May.27.2023 Original Report Judy Global Certification Corp. Date of Issue: May.27.2023 Report No:FR2-351602 Page3/48 TABLE OF CONTENTS ----------------------------------------------------------------------------------------------------- 3 1. GENERAL INFORMATION -------------------------------------------------------------------------------------------------------- 5 1.1 DESCRIPTION OF THE TESTED SAMPLES ----------------------------------------------------------------------------------------------- 6 2. TEST METHODOLOGY ------------------------------------------------------------------------------------------------------------- 7 2.1 GENERAL TEST PROCEDURES --------------------------------------------------------------------------------------------------- 7 2.2 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ----------------------------------------------------------------- 8 2.3 DESCRIPTION OF TEST MODES -------------------------------------------------------------------------------------------------- 9 2.4 DESCRIPTION OF THE SUPPORT EQUIPMENTS ------------------------------------------------------------------------------ 9 3. TEST AND MEASUREMENT EQUIPMENT ---------------------------------------------------------------------------------- 10 3.1 CALIBRATION ---------------------------------------------------------------------------------------------------------------------- 10 3.2 EQUIPMENT------------------------------------------------------------------------------------------------------------------------- 10 4. ANTENNA REQUIREMENTS ----------------------------------------------------------------------------------------------------- 12 4.1 STANDARD APPLICABLE ---------------------------------------------------------------------------------------------------------- 12 4.2 ANTENNA CONSTRUCTION AND DIRECTIONAL GAIN ------------------------------------------------------------------------- 12 5. CONDUCTED EMISSIONS -------------------------------------------------------------------------------------------------------- 13 5.1 TEST SETUP ------------------------------------------------------------------------------------------------------------------------ 13 5.2 LIMIT ------------------------------------------------------------------------------------------------------------------------------- 13 5.3 TEST PROCEDURE ----------------------------------------------------------------------------------------------------------------- 13 5.4 TEST RESULT ------------------------------------------------------------------------------------------------------------------- 14 5.5 TEST DATA: ------------------------------------------------------------------------------------------------------------------------ 14 6. PEAK OUTPUT POWER ----------------------------------------------------------------------------------------------------------- 15 6.1 TEST SETUP ------------------------------------------------------------------------------------------------------------------------ 15 6.2 LIMIT ------------------------------------------------------------------------------------------------------------------------------- 15 6.3 TEST PROCEDURE ------------------------------------------------------------------------------------------------------------- 15 6.4 TEST RESULT -------------------------------------------------------------------------------------------------------------------- 15 6.5 TEST DATA: ------------------------------------------------------------------------------------------------------------------------ 16 7. RADIATED BAND EDGE ----------------------------------------------------------------------------------------------------------- 17 7.1 TEST SETUP ------------------------------------------------------------------------------------------------------------------------ 17 7.2 LIMIT ------------------------------------------------------------------------------------------------------------------------------- 18 7.3 TEST RESULT ------------------------------------------------------------------------------------------------------------------- 18 7.4 TEST DATA: ------------------------------------------------------------------------------------------------------------------------ 19 8. 6DB BANDWIDTH ------------------------------------------------------------------------------------------------------------------- 23 8.1 TEST SETUP ------------------------------------------------------------------------------------------------------------------------ 23 8.2 LIMIT ------------------------------------------------------------------------------------------------------------------------------- 23 8.3 TEST PROCEDURE ------------------------------------------------------------------------------------------------------------- 23 8.4 TEST RESULT ----------------------------------------------------------…

Text truncated - open the document above for the full version.

Product Model： T300(US) 1.0 Version： 1.0 Manufacturer： Date： Checked By： TP-Link Corporation Limited Room 901, 9/F. , New East Ocean Centre, 9 Science Museum Road, Tsim Sha Tsui, Kowloon, Hong Konga TEL: 00852-37585503 http://www.tp-link.com/en Index I. Antenna Distribution ........................................................................................ 3 II. Electrical Characteristics ................................................................................ 3 III. Antenna Peak Gain........................................................................................... 3 IV. Antenna Radiation Pattern .............................................................................. 4 Page 3 Version:1.0 Issue Date: I. Antenna Distribution T300(US)1.0 II. Electrical Characteristics Ant1 Frequency 920~924MHz Impedance 50Ohm Antenna Type IFA Antenna Gain -6.53dBi@920~924MHz Radiation pattern Omni-Directional III. Antenna Peak Gain Ant1 Frequency(MHz) 920 922 924 Gain(dBi) -6.79 -6.62 -6.53 Page 4 Version:1.0 Issue Date: IV. Antenna Radiation Pattern Ant1

Global Certification Corp. 報告編號:TR3-351602 日期: 民國112年05月27日 測試照 廠牌：tp-link、tapo 型號：Tapo T300 01. 禁用頻帶輻射發射之量測 1GHz 以下 (正面) 02. 禁用頻帶輻射發射之量測 1GHz 以下 (背面) 1 2 Global Certification Corp. 報告編號:TR3-351602 日期: 民國112年05月27日 測試照 廠牌：tp-link、tapo 型號：Tapo T300 03. 輸出峰值功率 / 開放頻帶邊緣量測 / 20dB 頻寬量測 / 6dB 頻寬量測 / 載波頻率間隔之量測 / 載波頻率佔用週期之量測 / 頻道數之量測 / 功率密度之量測 2 2