2AZNY-2023XRemote Control Car

REMOTE CONTROL CAR USER MANUAL 2023-3 Suitable for age 3 CATALOGUE 02~07 08~13 14~19 20~25 26~31 01 ENGLISH GERMAN FRENCH ITALIAN SPANISH 1* Remote Control Car 1* Remote Controller 1* Instruction manual DELIVERY CONTENTS ENGLISH 02 BATTERY USE INSTRUCTION AND CAUTIONS 1. Non-rechargeable batteries are not to be recharged. 2. Rechargeable batteries are only to be charged under adult supervi- sion (for toys supplied). 3. Rechargeable batteries are to be removed from the toy before being charged. 4. Different types of batteries or new and used batteries are not to be mixed. 5. Batteries are to be inserted with the correct polarity. 6. Exhausted batteries are to be removed from the toy. 7. The supply terminals are not to be short-circuited. 8. Non-professionals shall not detach the batteries. When needed, it should be done by professionals. Firstly, loose the screws and open the bonnet. Then weld the cable with soldering iron. 9. Do not squeeze, impale or throw the batteries into fire, it may have the risk of explosion. 10. Avoid placing the car in an extremely cold or hot environment for a long time. Extreme environments can reduce the battery life inside the car. 03 REMOTE CONTROL CAR REMOTE CONTROLLER 1. Open the battery cover using the screwdriver. 2. Load two 1.5V AA batteries following the polarity markings (+ and -) inside the battery compartment. 3. Replace the battery cover and tighten the screws. 1. Open the battery cover using the screwdriver. 2. Load three 1.5V AA batteries following the polarity markings (+ and -) inside the battery compartment. 3. Replace the battery cover and tighten the screws. 3x 1.5V AA (Not included) 2x 1.5V AA (Not included) MUSIC: 3 CHOICES POWER BUTTON FORWARD/BACKWARD LEFT ROTATION/ RIGHT ROTATION 04 OPERATING INSTRUCTION 05 WEEE COMPLIANCE 06 CARE & MAINTENANCE 1. WARNING! Do not use the SGILE RC vehicle in road traffic. 2. Do not use the SGILE RC vehicle for transporting goods, persons or animals. 3. Never use the SGILE RC vehicle outdoors during rain or snowfall. The car must not be run through water, puddles and snow, and must always be kept stored in a dry place. 4. Avoid running on courses which are laid exclusively with sand. 5. Do not expose the SGILE RC vehicle to direct sunlight. 6. Never subject the SGILE car to repeated changes of load - that means continuously reversin 7. Never throw the car on the floor from a standing position. 8. The SGILE RC vehicle must be inspected before and after operation, each time it is used, to ensure that it has not become disasembled. Any screws or nuts that may have become loosened during operation must be tightened. Please help the environment by disposing of your product responsibly at the end of its life. The wheeled bin symbol indicates that this product should not be disposed of in your household waste containers. Instead, the product should be disposed of by using a designated collection point for the recycling of waste electrical and electronic equipment, The Waste of Electrical and Electronic Equipment(WEEE) Directive (2012/19/EU) requires that the best available recycling techniques be employed to minimize the impact on the environment. Recycling electronics helps by keeping harmful chemicals out of the environment, and also saves money by reusing precious metals. Remove any batteries and dispose of them and the product at your local authority recycling facility. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the location where you purchased this product. DECLARATION OF CONFORMITY Hereby, Fujian EastWest Lifewit Technology Co.,LTD declares that this model including the controller conforms with the fundamental require- ments of the following EC directives: EC Directives Toys (Safety) requlations 2011 and the other relevant regulations of Directive Radio equipment regulations 2014/53/EU. The original declaration of conformity can be requested from https://ww- w.sgile.com/pages/compliance. Maximum radio-frequency power transmitted: <10dBm Frequency range: 2410MHz-2473MHz The appliance is only to be used with the power supply unit provided with the appliance. The use of a different power supply unit may lead to the permanent damage of the battery and neighbouring parts, as well as physical injury! Battery chargers used with the toy are to be regularly examined for damage to the cord, plug, enclosure and other parts, and in the event of such damage, they must not be used until the damage has been repaired. WARNING! danger of pinching during operation! Remove all packaging materials and wire fastenings before handing the toy over to the child. Please retain the packaging and address for information and in the event of any questions. 07 GERMAN 08 1* Ferngesteuertes Auto 1* Fernbedienung 1* Gebrauchsanweisung LIEFERUMFANG ANWEISUNGEN UND VORSICHTSMABNAHMEN ZUR VERWENDUNG DER BATTERIE 1. Nicht wiederaufladbare Batterien sollten nicht aufgeladen werden. 2. Wiederaufladbare Batterie dürfen nur unter Aufsicht von Erwachsenen aufgeladen werden (für mitgeliefertes Spielzeug). 3. Wiederaufladbare Batterien müssen vor dem Laden aus dem Spielzeug entfernt werden. 4. Verschiedene Batterietypen oder neue und gebrauchte Batterie dürfen nicht gemischt werden. 5. Batterie sind mit der richtigen Polarität einzulegen. 6. Erschöpfte Batterien sind aus dem Spielzeug zu entfernen. 7. Die Versorgungsklemmen dürfen nicht kurzgeschlossen werden. 8. Nichtprofis dürfen die Batterien nicht abnehmen. Be Bedarf sollte dies von Fachleuten durchgeführt werden. Lösen Sie zuerst die Schrauben und öffnen Sie die Motorhaube. Dann schweißen Sie das Kabel mit Lötkolben. 9. Drücken Sie die Batterien nicht zusammen, spießen Sie sie nicht auf und werfen Sie sie nicht ins Feuer. Andernfalls besteht Explosions- gefahr. 10. Stellen Sie das Auto nicht für längere Zeit in eine extrem kalte oder heiße Umgebung. Extreme Umgebungen kön…

Text truncated - open the document above for the full version.

FujianEastWestLifewitTechnologyCo.,LTD FederalCommunicationsCommission AuthorizationandEvaluationDivision EquipmentAuthorizationBranch 7435OaklandMillsRoad Columbia,MD21046 4/8/24 U.S.AgentDesignation FujianEastWestLifewitTechnologyCo.,LTDacknowledgestheirconsentforthefollowingcontactlocatedin theUnitedStatestoactastheiragentforserviceofprocessfortheequipmentforwhichauthorizationissought (FCCID:2AZNY-2023X): NameandcompanyofU.S.agent:EASTWESTELECTRONICCOMMERCECOUSLIMITED PhysicalU.S.addressofagent:3500SouthDupontHighway,DoverDE19901US FRNofU.S.agent:0033602186 EmailaddressofU.S.agent:[email protected] EASTWESTELECTRONICCOMMERCECOUSLIMITEDacknowledgestheirobligationtoacceptserviceof processonbehalfofFujianEastWestLifewitTechnologyCo.,LTD. FujianEastWestLifewitTechnologyCo.,LTDwiththeFRN0030816284acceptsitsobligationtomaintainan agentforserviceofprocessintheUnitedStatesfornolessthanoneyearaftereitherthegranteehas permanentlyterminatedallmarketingandimportationoftheapplicableequipmentwithintheU.S.,orthe conclusionofanyCommission-relatedadministrativeorjudicialproceedinginvolvingtheequipment,whicheveris later. Bysigningthisform,weconfirmtheaboveandthatweareawareoftheapplicationrequirementslistedunder§ 2.911(d)(7). TheinformationprovidedinthisletterisbasedonthereferencedrulepartsofTitle47oftheCFRaswellasKDB 986446D01. Anexpirationdateforthisletterdoesnotexist.IncasetheU.S.agentchanges,thegranteeisobligatedtonotify theFCCwithin30daysviathegrantingTCB. Sincerely, Signature YanbingLi ProductDirector FujianEastWestLifewitTechnologyCo.,LTD Signature XUEFANGTANG Director EASTWESTELECTRONICCOMMERCECOUS LIMITED 4 8 _ [ m o d e l ] U S _ A g e n t _ 2 . 9 1 1 ( d ) ( 7 ) - U , V 0 5

Page 1 of 3 FCC ID: 2AZNY-2023X Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity External Photos of the EUT Fig. 1 Fig. 2 Page 2 of 3 FCC ID: 2AZNY-2023X Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 3 Fig. 4 Page 3 of 3 FCC ID: 2AZNY-2023X Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 5 Fig. 6

Page 1 of 1 FCC ID:2AZNY-2023X Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity LABEL AND LOCATION (Size: L0.5cm x 1.5cm) Label Location Remote Control Car Model: 2023-3 FCC ID: 2AZNY-2023X IC:30108-2023X HVIN: 2023-3

Page 1 of 2 FCC ID:2AZNY-2023X Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Internal Photos of the EUT Fig. 1 Fig. 2 Page 2 of 2 FCC ID:2AZNY-2023X Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 3 Fig. 4 TX Antenna

Page 1 of 3 FCC ID:2AZNY-2023X Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC RF Exposure Evaluation 1. Product Information EUT Remote Control Car Test Model 2023-3 Additional Model No. 2023-1, 2023-2, 2023-4, 2023-5, 2023-6 Model Declaration PCB board, structure and internal of these model(s) are the same, So no additional models were tested Power Supply DC1.5V*2 AA battery Hardware Version V1.0 Software Version V1.0 Frequency Range 2410MHz-2473MHz Channel Number 64 Modulation Type GFSK Antenna Description Internal Antenna, 0dBi(max.) Exposure category General population/uncontrolled environment EUT Type Production Unit Device Type Portable Device Page 2 of 3 FCC ID:2AZNY-2023X Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity 2.Evaluation method and Limit According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.“ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to f) in section 4.1 is applied to determine SAR test exclusion. When one of the following test exclusion conditions is satisfied for all combinations of simultaneous transmission configurations, further equipment approval is not required to incorporate transmitter modules in host devices that operate in the mixed mobile and portable host platform exposure conditions. The grantee is responsible for documenting this according to Class I permissive change requirements. Antennas that qualify for standalone SAR test exclusion must apply the estimated standalone SAR to determine simultaneous transmission test exclusion. a) The [∑ of (the highest measured or estimated SAR for each standalone antenna configuration, adjusted for maximum tune-up tolerance) / 1.6 W/kg] + [∑ of MPE ratios] is ≤ 1.0. b)The SAR to peak location separation ratios of all simultaneously transmitting antenna pairs operating in portable device exposure conditions are all ≤ -0.19, and the [∑ of MPE ratios] is ≤ 1.0. 3. Refer Evaluation Method ANSI C95.1–1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. FCC KDB publication 447498 D01 General 1 RF Exposure Guidance v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies. FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits. FCC CFR 47 part2 2.1093: Radiofrequency radiation exposure evaluation: portable devices Page 3 of 3 FCC ID:2AZNY-2023X Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity 4. Radiation Power Test Procedure TX frequency range: 2410MHz Device category: Portable device (Distance: 5mm) Max. Field Strength: 84.55dBuV/m @3m EIRP=E-104.7+20logD=84.55-104.7+20log3=-10.61dBm Maximum Conducted Output Power: -10.61dBm Tune-up: -10±1 5. Evaluation Results Band/Mode f (GHz) Antenna Distance (mm) RF output power SAR Test Exclusion Threshold SAR Test Exclusion dBm mW GFSK 2.410 5 -9.0 0.1259 0.0391< 3.0 Yes Remark: 1. Ou…

Text truncated - open the document above for the full version.

LXH Antenna Specification for Approval Customer Name： Product Name：2.4G antenna 40mm white Product Name: Part NO.:C10-35-2.5 Write By： Issued Date: FEB-15-2023 Customer: R&D Dept Business Dept Approved By LXH R&D Dept Engineer Dept Approval Product Specification A. Electrical Characteristics Frequency 2405MHz ~2480MHz VSWR <3.0 Efficiency >30% Impedance 50 Ohm Polarization Line Gain 0DBi B. Material & Mechanical Characteristics Material of Radiator Cu Cable Type 1.0 12P白色 Connector Type : NO Dimension C. Environmental Operation Temperature - 30 °C ~ + 80 °C Storage Temperature - 30 °C ~ + 85 °C Test Equipment & Conditions 1．Network Analyzers : Agilent 8753D 5071B 2．Communications Test Set: Agilent E5515C 3．3D Chamber Test System Effiency &Gain Effiency &Gain 2.40 -0.00 2.440 -0.11 2.48 -0.13 Radiation Pattern:

Page 1 of 33 FCC ID:2AZNY-2023X Report No.: LCSA03084055EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC TEST REPORT FOR Fujian EastWest Lifewit Technology Co.,LTD Remote Control Car Test Model: 2023-3 Additional Model No.: Please Refer to Page 6 Prepared for : Fujian EastWest Lifewit Technology Co.,LTD Address : Rm 1201-1205, Bld 18, 2nd Phase of Innovation Park, no.7, Wulongjiang Mid-Ave, Fuzhou High-tech Zone, Fuzhou 350108, China Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd Address : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel : (+86)755-82591330 Fax : (+86)755-82591332 Web : www.LCS-cert.com Mail : [email protected] Date of receipt of test sample : March 12, 2024 Number of tested samples : 2 Sample No. : A240307059-1, A240307059-2 Sample number : Prototype Date of Test : March 12, 2024 ~ March 28, 2024 Date of Report : March 28, 2024 Page 2 of 33 FCC ID:2AZNY-2023X Report No.: LCSA03084055EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC TEST REPORT FCC CFR 47 PART 15 C (15.249) Report Reference No. ................. : LCSA03084055EA Date of Issue................................... : March 28, 2024 Testing Laboratory Name ............ : Shenzhen LCS Compliance Testing Laboratory Ltd. Address ........................................... : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Testing Location/ Procedure .......... : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ......................... : Fujian EastWest Lifewit Technology Co.,LTD Address ........................................... : Rm 1201-1205, Bld 18, 2nd Phase of Innovation Park, no.7, Wulongjiang Mid-Ave, Fuzhou High-tech Zone, Fuzhou 350108, China Test Specification Standard ......................................... : FCC CFR 47 PART 15 C(15.249) / ANSI C63.10: 2013 Test Report Form No. ..................... : LCSEMC-1.0 TRF Originator ................................ : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF ..................................... : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description. .................. : Remote Control Car Trade Mark ..................................... : SGILE Test Model ...................................... : 2023-3 Ratings ............................................ : DC1.5V*2 AA battery Result ........................................... : Positive Compiled by: Supervised by: Approved by: Jack Liu/Administrator Cary Luo/ Technique principal Gavin Liang/ Manager Page 3 of 33 FCC ID:2AZNY-2023X Report No.: LCSA03084055EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC -- TEST REPORT Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCSA03084055EA March 28, 2024 Date of issue Test Model.............................. : 2023-3 EUT......................................... : Remote Control Car Applicant............................... : Fujian EastWest Lifewit Technology Co.,LTD Address.................................. : Rm 1201-1205, Bld 18, 2nd Phase of Innovation Park, no.7, Wulongjiang Mid-Ave, Fuzhou High-tech Zone, Fuzhou 350108, China Telephone............................... : / Fax.......................................... : / Manufacturer........................ : Fujian EastWest Lifewit Technology Co.,LTD Address................................... : Rm 1201-1205, Bld 18, 2nd Phase of Innovation Park, no.7, Wulongjiang Mid-Ave, Fuzhou High-tech Zone, Fuzhou 350108, China Telephone............................... : / Fax.......................................... : / Factory................................... : Fujian EastWest Lifewit Technology Co.,LTD Address................................... : Rm 1201-1205, Bld 18, 2nd Phase of Innovation Park, no.7, Wulongjiang Mid-Ave, Fuzhou High-tech Zone, Fuzhou 350108, China Telephone............................... : / Fax.......................................... : / Page 4 of 33 FCC ID:2AZNY-2023X Report No.: LCSA03084055EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Revision History Report Version Issue Date Revision Content Revised By 000 March 28, 2024 Initial Issue -- Page 5 of 33 FCC ID:2AZNY-2023X Report No.: LCSA03084055EA Shenzhen LCS Compliance …

Text truncated - open the document above for the full version.

Page 1 of 1 FCC ID:2AZNY-2023X Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Test Setup Photos of the EUT Test Setup Photo(s) of Radiated Emissions Measurement Fig. 1 Fig. 2