2BAQM-Q60TSmart watch

FCC Caution ： This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Warnings Q60T-Smart watch User Manual（English version） Product model:Q60T Product name:Smart watch Part drawing number:- Size: 83×53mm (organ fold) after forming; 105g matte powder paper cover Q 6 0 T The contents of this manual are provided by "as is" and, except as required by applicable laws, Ultra Easy Health Technology (Guangzhou) Co., Ltd, does not disclaim any expressed or implied warranties, including but not limit to warranties to marketability or fitness for a particular purpose with respect to the contents of this manual. To the extent permitted by applicable laws, Ultra Easy Health Technology (Guangzhou) Co., Ltd , shall in not event be liable for any special, incidental, indirect or consequential damages, nor for any loss of profit, data or anticipated savings, arising out of the use of the relevant contents of this manual, and the product described in this manual. To the extent permitted by relevant laws, in any event, the maximum liability of Ultra Easy Health Technology (Guangzhou) Co., Ltd for damages arising from using the product described in this manual (except for damages under applicable law in cases involving personal injury) is limited to the product price paid by you. Product model:Q60T Display screen size:1.83 TFT Battery capacity:340mAh Product model:Q60T Manufacturer: Ultra Easy Health Technology (Guangzhou) Co., Ltd Office address:228 Huadi Avenue Middle, Liwan District, Guangzhou Resolution:240*280 Product size: 43.98*37*11.5mm

Ultra Easy Health Technology (Guangzhou) Co., LTD 2023.04.18 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for 2BAQM-Q60T [Ultra Easy Health Technology (Guangzhou) Co., LTD] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, (Applicant signature) (Applicant printed name) xuyuan chen Ultra Easy Health Technology (Guangzhou) Co., LTD 2023.04.18 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for 2BAQM-Q60T [Ultra Easy Health Technology (Guangzhou) Co., LTD] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) xuyuan chen

Ultra Easy Health Technology (Guangzhou) Co., LTD 2023.04.18 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: CONFIDENTIALITY REQUEST FOR EUT NAME: Smart watch Trademark: N/A MODEL : Q60T FCC ID : 2BAQM-Q60T To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the - Block Diagram - Schematics - Operational Description required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, Client’s signature: Client’s name / title : xuyuan chen /Manager Contact information / address: 228 Huadi Avenue Middle, Liwan District, Guangzhou, China 51000

Ultra Easy Health Technology (Guangzhou) Co., LTD 2023.04.18 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen BCTC Testing Co., Ltd to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Client’s signature: Client’s name / title : xuyuan chen /Manager Contact information / address: 228 Huadi Avenue Middle, Liwan District, Guangzhou, China 51000

External Photos

Size:10*5mm Smart watch FCC ID: 2BAQM-Q60T Label location

Internal Photos Antenna

RF EXPOSURE EVALUATION METHOD FCC ID: 2BAQM- Q60T Applicable standard： In accordance with FCC 47 CFR part 2 (2.1093) this device has been defined as a portable device which is defined as a transmitting device designed to be used so that the radiating structure(s) of the device is/are within 20 centimeters of the body of the user. Portable devices must be evaluated using the specified in FCC 47 CFR part 2 (2.1093) and ANSI/IEEEC95.1-1992. and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528-2003. Per FCC KDB 447498 D01 v06, the 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances s 50 mm are determined by: SAR Test Exclusion Thresholds for 100 MHz – 6 GHz and ≤ 50 mm Approximate SAR Test Exclusion Power Thresholds at Selected Frequencies and Test Separation Distances are illustrated in the following Table. The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. BT Condition Mode Frequency (MHz) Conducted Power (dBm) Limit (dBm) Verdict NVNT 1-DH1 2402 -3.14 21 Pass NVNT 1-DH1 2441 -2.85 21 Pass NVNT 1-DH1 2480 -2.28 21 Pass NVNT 2-DH1 2402 -3.00 21 Pass NVNT 2-DH1 2441 -2.69 21 Pass NVNT 2-DH1 2480 -2.10 21 Pass NVNT 3-DH1 2402 -2.30 21 Pass NVNT 3-DH1 2441 -2.15 21 Pass NVNT 3-DH1 2480 -1.47 21 Pass max possible output power (PK,conducted)：-1±1dBm -1.09dBi logarithmic terms convert to numeric result is nearly 0.78 0dBm=1mW 2402MHz [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance,mm)] · [√f(GHz)]= 1/5*√2.402=0.31≤3.0 2441MHz [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance,mm)] · [√f(GHz)]= 1/5*√2.441=0.312≤3.0 2480MHz [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance,mm)] · [√f(GHz)]= 1/5*√2.48=0.315≤3.0 BLE Mode Frequency(MHz) Maximum Conducted Output Power(PK) (dBm) Conducted Output Power Limit(dBm) GFSK(1Mbps) 2402 -0.13 30 2440 0.10 30 2480 0.74 30 GFSK(2Mbps) 2402 0.51 30 2440 0.31 30 2480 0.94 30 max possible output power (PK,conducted)：0±1dBm -1.09dBi logarithmic terms convert to numeric result is nearly 0.78 1dBm=1.26mW 2402MHz [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance,mm)] · [√f(GHz)]= 1.26/5*√2.402=0.391≤3.0 2440MHz [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance,mm)] · [√f(GHz)]= 1.26/5*√2.440=0.394≤3.0 2480MHz [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance,mm)] · [√f(GHz)]= 1.26/5*√2.48=0.397≤3.0 Conclusion: 1. [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] * [√f(GHz)] < 3.0. 2. SAR Test Exclusion Thresholds is 3.0 for separation distance 5mm. Therefore, SAR test is not required.

Shenzhen Yusheng Communication Equipment Co., LTD Q60 specification Antenna name: Q6 0 Antenna frequency: BT:2400-2500MHZ Antenna material: FPC Antenna version: V0.1 Address: 1001 Zhongshan Garden Road, Liuxian Hole, Xili Street, Nanshan District, Shenzhen Shenzhen Yusheng Communication Equipment Co., LTD 1． Antenna passive parameter Shenzhen Yusheng Communication Equipment Co., LTD 2 2.4G -2D Shenzhen Yusheng Communication Equipment Co., LTD 3.2.4G -3D Shenzhen Yusheng Communication Equipment Co., LTD 4.Engineering drawing

No.：BCTC/RF-EMC-007 Page: 1 of 80 Edition：A.5 TEST REPORT Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC2303139986-1E Applicant: Ultra Easy Health Technology (Guangzhou) Co., LTD Product Name: Smart watch Model/Type reference: Q60T Tested Date: 2023-03-31 to 2023-04-04 Issued Date: 2023-04-04 Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 2 of 80 Edition：A.5 FCC ID: 2BAQM-Q60T The test report is effective only with both signature and specialized stamp.This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Testing Co., Ltd, this report can’t be reproduced except in full.The tested sample(s) and the sample information are provided by the client. Product Name: Smart watch Trademark: N/A Model/Type Reference: Q60T Prepared For: Ultra Easy Health Technology (Guangzhou) Co., LTD Address: 228 Huadi Avenue Middle, Liwan District, Guangzhou, China 51000 Manufacturer: Ultra Easy Health Technology (Guangzhou) Co., LTD Address: 228 Huadi Avenue Middle, Liwan District, Guangzhou, China 51000 Prepared By: Shenzhen BCTC Testing Co., Ltd. Address: 1-2/F., Building B, Pengzhou Industrial Park, No.158, Fuyuan 1st Road, Zhancheng, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, China Sample Received Date: 2023-03-31 Sample tested Date: 2023-03-31 to 2023-04-04 Issue Date: 2023-04-04 Report No.: BCTC2303139986-1E Test Standards: FCC Part15.247 ANSI C63.10-2013 Test Results: PASS Remark: This is Bluetooth Classic radio test report. Tested by: Approved by: Lei Chen/Project Handler Zero Zhou/Reviewer Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 3 of 80 Edition：A.5 Table Of Content Test Report Declaration Page 1. Version .................................................................................................................. 5 2. Test Summary ....................................................................................................... 6 3. Measurement Uncertainty ..................................................................................... 7 4. Product Information And Test Setup ..................................................................... 8 4.1 Product Information ............................................................................................... 8 4.2 Test Setup Configuration ...................................................................................... 8 4.3 Support Equipment ............................................................................................... 9 4.4 Channel List .......................................................................................................... 9 4.5 Test Mode ........................................................................................................... 10 4.6 Table Of Parameters Of Text Software Setting ................................................... 10 5. Test Facility And Test Instrument Used ............................................................... 11 5.1 Test Facility ......................................................................................................... 11 5.2 Test Instrument Used .......................................................................................... 11 6. Conducted Emissions .......................................................................................... 13 6.1 Block Diagram Of Test Setup .............................................................................. 13 6.2 Limit .................................................................................................................... 13 6.3 Test procedure .................................................................................................... 13 6.4 EUT operating Conditions ................................................................................... 13 6.5 Test Result .......................................................................................................... 14 7. Radiated emissions ............................................................................................. 16 7.1 Block Diagram Of Test Setup .............................................................................. 16 7.2 Limit .................................................................................................................... 17 7.3 Test procedure .................................................................................................... 18 7.4 EUT operating Conditions ................................................................................... 19 7.5 Test Result .......................................................................................................... 20 8. Radiated Band Emission Measurement And Restricted Bands Of Operation ..... 24 8.1 Block Diagram Of Test Setup .............................................................................. 24 8.2 Limit .................................................................................................................... 24 8.3 Test procedure .................................................................................................... 25 8.4 EUT operating Conditions ................................................................................... 25 8.5 Test Result .......................................................................................................... 26 9. Spurious RF Conducted Emissions ..................................................................... 27 9.1 Block Diagram Of Test Setup .............................................................................. 27 9.2 Limit .................................................................................................................... 27 9.3 Test procedure .................................................................................................... 27 9.4 Test Result .......................................................................................................... 28 10. 20 d…

Text truncated - open the document above for the full version.

Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 67 of 80 Edition：A.5 13. Number Of Hopping Frequency 13.1 Block Diagram Of Test Setup 13.2 Limit Frequency hopping systems in the 2400-2483.5 MHz band shall use at least 15 channels. 13.3 Test procedure 1. Remove the antenna from the EUT and then connect a low RF cable from the antenna port to the spectrum. 2. Set the spectrum analyzer: RBW = 100kHz. VBW = 300kHz. Sweep = auto; Detector Function = Peak. Trace = Max hold. 3. Allow the trace to stabilize. It may prove necessary to break the span up to sections. in order to clearly show all of the hopping frequencies. The limit is specified in one of the subparagraphs of this Section. 4. Set the spectrum analyzer: Start Frequency = 2.4GHz, Stop Frequency = 2.4835GHz. Sweep=auto; 13.4 Test Result Condition Mode Hopping Number Limit Verdict NVNT 1-DH1 79 15 Pass NVNT 2-DH1 79 15 Pass NVNT 3-DH1 79 15 Pass Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 68 of 80 Edition：A.5 Test Graphs Hopping No. NVNT 1-DH1 2441MHz Hopping No. NVNT 2-DH1 2441MHz Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 69 of 80 Edition：A.5 Hopping No. NVNT 3-DH1 2441MHz Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 70 of 80 Edition：A.5 14. Dwell Time 14.1 Block Diagram Of Test Setup 14.2 Limit Frequency hopping systems in the 2400-2483.5 MHz band shall use at least 15 channels. The average time of occupancy on any channel shall not be greater than 0.4 seconds within a period of 0.4 seconds multiplied by the number of hopping channels employed. Frequency hopping systems may avoid or suppress transmissions on a particular hopping frequency provided that a minimum of 15 channels are used. 14.3 Test procedure 1. Remove the antenna from the EUT and then connect a low RF cable from the antenna port to the spectrum. 2. Set spectrum analyzer span = 0. Centred on a hopping channel; 3. Set RBW = 1MHz and VBW = 3MHz.Sweep = as necessary to capture the entire dwell time per hopping channel. Set the EUT for DH5, DH3 and DH1 packet transmitting. 4. Use the marker-delta function to determine the dwell time. If this value varies with different modes of operation (e.g.. data rate. modulation format. etc.). repeat this test for each variation. The limit is specified in one of the subparagraphs of this Section. Submit this plot(s). 14.4 Test Result DH5 Packet permit maximum 1600 / 79 / 6 hops per second in each channel (5 time slots RX, 1 time slot TX). DH3 Packet permit maximum 1600 / 79 / 4 hops per second in each channel (3 time slots RX, 1 time slot TX). DH1 Packet permit maximum 1600 / 79 /2 hops per second in each channel (1 time slot RX, 1 time slot TX). So, the Dwell Time can be calculated as follows: DH5:1600/79/6*0.4*79*(MkrDelta)/1000 DH3:1600/79/4*0.4*79*(MkrDelta)/1000 DH1:1600/79/2*0.4*79*(MkrDelta)/1000 Remark: Mkr Delta is once pulse time. Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 71 of 80 Edition：A.5 Modulation Channel Data Packet pulse time(ms) Dwell Time(s) Limits(s) GFSK Middle 1DH1 0.383 0.123 0.4 1DH3 1.640 0.262 0.4 1DH5 2.887 0.308 0.4 π/ 4 DQPSK Middle 2DH1 0.391 0.125 0.4 2DH3 1.643 0.263 0.4 2DH5 2.892 0.308 0.4 8DPSK Middle 3DH1 0.391 0.125 0.4 3DH3 1.642 0.263 0.4 3DH5 2.893 0.309 0.4 Test Graphs Dwell NVNT 1-DH1 2441MHz One Burst Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 72 of 80 Edition：A.5 Dwell NVNT 1-DH3 2441MHz One Burst Dwell NVNT 1-DH5 2441MHz One Burst Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 73 of 80 Edition：A.5 Dwell NVNT 2-DH1 2441MHz One Burst Dwell NVNT 2-DH3 2441MHz One Burst Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 74 of 80 Edition：A.5 Dwell NVNT 2-DH5 2441MHz One Burst Dwell NVNT 3-DH1 2441MHz One Burst Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 75 of 80 Edition：A.5 Dwell NVNT 3-DH3 2441MHz One Burst Dwell NVNT 3-DH5 2441MHz One Burst Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 76 of 80 Edition：A.5 15. Antenna Requirement 15.1 Limit 15.203 requirement: For intentional device, according to 15.203: an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 15.2 Test Result The EUT antenna is FPC antenna, fulfill the requirement of this section. Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 77 of 80 Edition：A.5 16. EUT Photographs EUT Photo NOTE: Appendix-Photographs Of EUT Constructional Details Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 78 of 80 Edition：A.5 17. EUT Test Setup Photographs Conducted emissions Radiated Measurement Photos Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 79 of 80 Edition：A.5 Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 80 of 80 Edition：A.5 STATEMENT 1. The equipment lists are traceable to the national reference standards. 2. The test report can not be partially copied unless prior written approval is issued from our lab. 3. The test report is invalid without the "special seal for inspection and testing". 4. The test report is invalid without the signature of the approver. 5. The test process and test result is only related to the Unit Under Test. 6. Sample information is provided by the client and the laboratory is not responsible for its authenticity. 7. The test report without CMA mark is only used for scientific research, teaching, enterprise product development and internal quality control purposes. 8. The quality system of our laboratory is in accordance with ISO/IEC17025. 9. If there is any objection to this test report, the client should inform issuing laboratory within 15 days from the date of receiving test report. Address: 1-2/F., Building B, Pengzhou Industrial Park, No.158, Fuyuan 1st Road, Zhancheng, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, China TEL：400-788-9558 P. C.: 518103 FAX：0755-33229357 Website：http://www.chnbctc.com E-Mail：[email protected] ※※※※※ END ※※※※※

Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 78 of 80 Edition：A.5 17. EUT Test Setup Photographs Conducted emissions Radiated Measurement Photos Report No.:BCTC2303139986-1E No.：BCTC/RF-EMC-007 Page: 79 of 80 Edition：A.5