2BG4HJY-022-in-1 Wireless Charger and Book Light

2-in-1 Wireless Charger and Book Light Product Name Product ModelJY - 02 Input Voltage 12V Material ABS Phone Output 5W/7.5W/10W/15W Apple Watch Output 2.5W Light Power 4WProduct Size 160 x 115 x 120 mm Product Parameters 2-in-1 Wireless Charger and Book Light Please read carefully before use Color Box, Product, 20W Adapter, Cable, User Manual. Packing List The order of indicator lights from left to right corresponds to a battery level of 0% ~ 30%, 31% ~ 50%, 51% ~ 75%, 76% ~ 100%. Key Introduction Short press to turn on/off the light. Short press to adjust the brightness of the light from 10% ~ 50% ~ 100%. Long press for stepless brightness adjustment 10%~100%. Color Temperature Key Power Indicators Dimming Key Short press to adjust color temperature. Cool white, Warm white, Neutral white. Power ON/OFF Thank you for your purchase. The product comes with a 12-month warranty period. If you have any issues about the product, please feel free to contact us at any time. Our email is: [email protected] Customer after-sale service FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device a distance 15cm surrounding the device and 20cm above the top surface of the device must be respected.

Shenzhen Jiuyang Technology Co., Ltd Room 401, Building 7, Yahao Xuan, No. 502 Jian'an 1st Road, Wenhui Community, Xin'an Street, Bao'an District, Shenzhen, China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 6/22/2024 U.S. Agent Designation Shenzhen Jiuyang Technology Co., Ltd acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2BG4HJY-02): Name and company of U.S. agent: Formates LLC Physical U.S. address of agent: 1400 Hudson St, Hoboken, New Jersey, 07030, USA FRN of U.S. agent: 0033456468 Email address of U.S. agent: [email protected] Formates LLC acknowledges their obligation to accept service of process on behalf of Shenzhen Jiuyang Technology Co., Ltd. Shenzhen Jiuyang Technology Co., Ltd with the FRN 0035577006 accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Jacky Ding Certification Contact Shenzhen Jiuyang Technology Co., Ltd Signature Abi Aribisala Project Manager Formates LLC 48_[mo del] US_Agent_2.911(d)(7) - U, V0 5

Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2BG4HJY-02 This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 1 of 4 EXTERIOR PHOTOGRAPHS OF EUT Fig.1 Fig.2 Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2BG4HJY-02 This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 2 of 4 Fig.3 Fig.4 Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2BG4HJY-02 This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 3 of 4 Fig.5 Fig.6 Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2BG4HJY-02 This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 4 of 4 Fig.7

Label Location: FCC ID: 2BG4HJY-02

Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2BG4HJY-02 This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 1 of 3 INTERIOR PHOTOGRAPHS OF EUT Fig.1 Fig.2 Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2BG4HJY-02 This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 2 of 3 Fig.3 Fig.4 Antenna Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2BG4HJY-02 This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 3 of 3 Fig.5 Fig.6

Page 1 of 9 Report No.: TZ240605849-E2 FCC TEST REPORT Test report On Behalf of Shenzhen Jiuyang Technology Co., Ltd For 2-in-1 Wireless Charger and Book Light Model No.: JY - 02 FCC ID: 2BG4HJY-02 Prepared for : Shenzhen Jiuyang Technology Co., Ltd Room 401, Building 7, Yahao Xuan, No. 502 Jian’an 1st Road, Wenhui Community, Xin’an Street, Bao’an District, Shenzhen, China Prepared By : Shenzhen Tongzhou Testing Co.,Ltd 1th Floor, Building 1, Haomai High-tech Park, Huating Road 387, Dalang Street, Longhua, Shenzhen, China Date of Test: 2024/6/12 ~ 2024/6/18 Date of Report: 2024/6/19 Report Number: TZ240605849-E2 The test report apply only to the specific sample(s) tested under stated test conditions It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Page 2 of 9 Report No.: TZ240605849-E2 TEST RESULT CERTIFICATION Applicant’s name ................. : Shenzhen Jiuyang Technology Co., Ltd Address ................................. : Room 401, Building 7, Yahao Xuan, No. 502 Jian’an 1st Road, Wenhui Community, Xin’an Street, Bao’an District, Shenzhen, China Manufacture's Name ............ : Shenzhen Jiuyang Technology Co., Ltd Address ................................. : Room 401, Building 7, Yahao Xuan, No. 502 Jian’an 1st Road, Wenhui Community, Xin’an Street, Bao’an District, Shenzhen, China Product description Trade Mark ............................ : N/A Product name ........................... : 2-in-1 Wireless Charger and Book Light Model ..................................... : JY - 02 Standards ............................. : FCC Rules and Regulations Part 2.1091, 680106 D01 Wireless Power Transfer v04 This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Tongzhou Testing Co.,Ltd is acknowledged as copyright owner and source of the material. Shenzhen Tongzhou Testing Co.,Ltd takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Date of Test ............................................ : Date (s) of performance of tests ............. : 2024/6/12 ~ 2024/6/18 Date of Issue ........................................... : 2024/6/19 Test Result ............................................... : Pass Testing Engineer : (Nancy Li) Technical Manager : (Hugo Chen) Authorized Signatory : (Andy Zhang) Page 3 of 9 Report No.: TZ240605849-E2 1. GENERAL INFORMATION 1.1 General Description of EUT Equipment 2-in-1 Wireless Charger and Book Light Model Name JY - 02 Model Difference N/A Test Model JY - 02 Trade Mark N/A FCC ID 2BG4HJY-02 Antenna Type Coil Antenna Antenna Gain 0dBi Operation frequency 110.5– 205 KHz Test Frequency 128.5375 KHz Modulation Type ASK Power Rating Input: 12V2A Output: 5V1A, 7.5V1A, 9V1.12A, 9V1.67A (Wireless charger) Test Sample ID TZ240605849-1# Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. The EUT antenna is Coil Antenna. No antenna other than that furnished by the responsible party shall be used with the device. Page 4 of 9 Report No.: TZ240605849-E2 2. SUMMARY OF TEST RESULTS 2.1 Test procedures according to the technical standards: FCC KDB680106 D01 Wireless Power Transfer v04 FCC CFR 47 Standard Section Test Item Judgment Remark FCC CFR 47 part1, 1.1310 KDB680106 D01v04 Electric Field Strength (E) (V/m) PASS Magnetic Field Strength (H) (A/m) PASS 2.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ±U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 All emissions, radiated(<30M)(9KHz-30MHz) ±2.45dB 2 Temperature ±0.5°C 3 Humidity ±2% Page 5 of 9 Report No.: TZ240605849-E2 2.3 Test Instruments Equipment Manufacturer Model Serial no. Calibrated date Calibrated Due Magnetic field probe WAVECONTROL SMP2/WP400 19SN1101/19WP100558 2023-08-03 2024-08-02 NOTE: 1. The calibration interval of the above test instruments is 12 months. 2.4 Special Accessories No. Equipment Manufacturer Model 1 Wireless charger tester YBZ YBZ 2 AC adapter Xiaomi MDY-10-EH 2.5 Operation of EUT during testing Test Modes: Mode 1 AC/DC Adapter (12V/2A) + EUT + Wireless charger tester (Load 15W) Record Mode 2 AC/DC Adapter (12V/2A) + EUT + Wireless charger tester (Load 10W) Pre-test Mode 3 AC/DC Adapter (12V/2A) + EUT + Wireless charger tester (Load 7.5W) Pre-test Mode 4 AC/DC Adapter (12V/2A) + EUT + Wireless charger tester (Load 5W) Pre-test Note: All test modes were pre-tested, but we only recorded the worst case in this report. Page 6 of 9 Report No.: TZ240605849-E2 3. MAXIMUM PERMISSIBLE EXPOSURE Limit of Maximum Permissible Exposure Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180 / f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1 30 Note 1: f = frequency in MHz ; *Plane-wave equivalent power density Note 2: For the applicable limit, see FCC 1.1310, FCC KDB680106 D01 Wireless Power Transfer v04 Note 3: Emissions between 100 kHz to 300 kHz should be assessed versus the limits at 300 kHz in Table 1 of Section 1.1310: 614 V/m and 1.63 A/m. A KDB inquiry is required to determine the applicable exposure limits below 100 kHz. Page 7 of 9 Report No.: TZ240605849-E2 4. TEST PROCEDURE a. For devices designed fo…

Text truncated - open the document above for the full version.

1.MECHANICAL DIMENSION (UNIT:mm) 2.SCHEMATICS: ABC D1D2EFGHI 50±0.520.5±0.51.2±0.242±240±24±250±0.52.3±0.5 3.WINDING： 1.1底部印字100 STE P TAPE REMAR K N1 4.ELECTRICAL SPECIFICATION: ITEM SPEC 5.BILF OF MATERIAL： NO.SGS NO. 1 2 3 WIRE⌀0.08mm*105 2UEW 60mΩ Max TES T CON DCRIDC S-F TAIYI CO.,LTD MATERIAL SPECIFICATIONMANUFACTURER HI-POTQ值 TURNS AT 25°C WIRE TYPE ⌀0.08*105mm 2UEW 10TS (Ref) 韦立红何伟华谢超 APPROVED BY CHECKED BYDRAWN BY ITEM 100KHz,0.25V CORE G50L开L槽/0.8mm NANJINGJINNINGCO,LTD START-FINISH S-F L S-F SPECIFICATION FOR APPROVAL TITLE G50开槽 HRSW ELECTRONICS CO.,LTD PART NO EPOXY9999CUDAK CO.,LTD 6.5uH±10% Antenna Gain: 0dBi

Report No.: TZ240605849-E1 Page 1 of 20 FCC TEST REPORT Test report On Behalf of Shenzhen Jiuyang Technology Co., Ltd For 2-in-1 Wireless Charger and Book Light Model No.: JY - 02 FCC ID: 2BG4HJY-02 Prepared for : Shenzhen Jiuyang Technology Co., Ltd Room 401, Building 7, Yahao Xuan, No. 502 Jian’an 1st Road, Wenhui Community, Xin’an Street, Bao’an District, Shenzhen, China Prepared By : Shenzhen Tongzhou Testing Co.,Ltd 1th Floor, Building 1, Haomai High-tech Park, Huating Road 387, Dalang Street, Longhua, Shenzhen, China Date of Test: 2024/6/12 ~ 2024/6/18 Date of Report: 2024/6/19 Report Number: TZ240605849-E1 The test report apply only to the specific sample(s) tested under stated test conditions It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: TZ240605849-E1 Page 2 of 20 TEST RESULT CERTIFICATION Applicant’s name ................. : Shenzhen Jiuyang Technology Co., Ltd Address ................................. : Room 401, Building 7, Yahao Xuan, No. 502 Jian’an 1st Road, Wenhui Community, Xin’an Street, Bao’an District, Shenzhen, China Manufacture's Name ............ : Shenzhen Jiuyang Technology Co., Ltd Address ................................. : Room 401, Building 7, Yahao Xuan, No. 502 Jian’an 1st Road, Wenhui Community, Xin’an Street, Bao’an District, Shenzhen, China Product description Trade Mark ............................ : N/A Product name............................ : 2-in-1 Wireless Charger and Book Light Model..................................... : JY - 02 Standards ............................. : FCC Rules and Regulations Part 15 Subpart C ANSI C63.10: 2013 This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Tongzhou Testing Co.,Ltd is acknowledged as copyright owner and source of the material. Shenzhen Tongzhou Testing Co.,Ltd takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Date of Test ........................................... : Date (s) of performance of tests ............. : 2024/6/12 ~ 2024/6/18 Date of Issue .......................................... : 2024/6/19 Test Result.............................................. : Pass Testing Engineer : (Nancy Li) Technical Manager : (Hugo Chen) Authorized Signatory : (Andy Zhang) Report No.: TZ240605849-E1 Page 3 of 20 Table of Contents Page 1 TEST SUMMARY ................................................................................................ 4 1.1 TEST PROCEDURES AND RESULTS ......................................... 4 1.2 TEST FACILITY ............................................................................. 4 1.3 MEASUREMENT UNCERTAINTY ................................................ 4 2 GENERAL INFORMATION ................................................................................. 5 2.1 General Description of EUT ........................................................... 5 2.2 Operation of EUT during testing .................................................... 6 2.3 Description of Test Setup .............................................................. 6 2.4 Description of Test Facility ............................................................ 6 3 Measurement Instruments List ............................................................................ 8 4 CONDUCTED EMISSION TEST ......................................................................... 9 4.1 Block Diagram of Test Setup ......................................................... 9 4.2 Conducted Power Line Emission Limit .......................................... 9 4.3 Test Procedure .............................................................................. 9 4.4 Test Result ..................................................................................... 9 5 Bandwidth ......................................................................................................... 12 5.1 Block Diagram of Test Setup ....................................................... 12 5.2 Rules and specifications .............................................................. 12 5.3 Test Procedure ............................................................................ 12 5.4 Test Result ................................................................................... 13 6 RADIATED EMISSIONS ................................................................................... 14 6.1 Block Diagram of Test Setup ....................................................... 14 6.2 Rules and specifications .............................................................. 15 6.3 Test Procedure ............................................................................ 16 6.4 Test Result ................................................................................... 16 7 ANTENNA REQUIREMENT .............................................................................. 19 7. TEST SETUP Photographs of EUT .................................................................. 20 8. Exterior Photographs of the EUT ..................................................................... 20 9. INTERIOR Photographs of the EUT ................................................................. 20 Report No.: TZ240605849-E1 Page 4 of 20 1 TEST SUMMARY 1.1 TEST PROCEDURES AND RESULTS DESCRIPTION OF TEST FCC RULE RESULT CONDUCTED EMISSIONS TEST PART 15.207 COMPLIANT RADIATED EMISSION TEST PART 15.209 COMPLIANT BANDWIDTH MEASUREMENT PART 15.215 COMPLIANT ANTENNA REQUIREMENT PART 15.203 COMPLIANT 1.2 TEST FACILITY Test Firm : Shenzhen Tongzhou Testing Co.,Ltd Address 1th Floor, Building 1, Haomai High-tech Park, Huating Road 387, Dalang Street, Longhua, Shenzhen, China 1.3 MEASUREMENT UNCERTAINTY Measurement Uncertainty Conducted Emission Expanded Uncertainty = 2.23dB, k=2 Radiated emission expanded uncertainty(9kHz-3…

Text truncated - open the document above for the full version.

Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2BG4HJY-02 This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 1 of 2 TEST SETUP PHOTOS OF THE EUT Radiated Emission Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2BG4HJY-02 This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 2 of 2 Conducted Emission