2BPIZ-T5GGMRS Two Way Radio

Instruction Manual 30-Channel GMRS Two Way Radio  6$0&20 T5 * M ain Features Freq uen cy: 462.5500~462.7250MHz,467.5625~467.7125MHz H igh/Low TX Power configured to designated channels 30 Channels 121 Codes (38 CTCSS & 83 CDCSS)Grou p Function 3 VOX Levels10 Call TonesMonitorScanKey Lock Fu nction 2000 mAh Li Polymer Battery Flashl ight NOAA & Weather AlertWaterproof IP67 AI Noise ReductionFM Function Overview 1. LCD Display 2. Earphone & Charger Jack 3. Push-To-Talk (PTT) Key 4. Up / Monitor Key 5. Down / Scan Key 6. Power / Volume Knob 7. Group Key 8. Menu / WX Key 9. Call Tone /Key-Lock Key 10. Microphone 11. Speaker 12. Antenna 13. Flashlight LED 14. Flashlight Key GROUP Button – Enable the radio transmitting on GROUP-channel which is different from the PTT-channel. 12 1 3 2 4 9 10 11 5 6 8 14 15 15. FM Key 16 16. Position For Lanyard LCD Display Icons 1234 5 678 9 10 1112 131415 : Volume Size : High Power Model : Low Power Model: Coll Tone : Weather Alert: Battery Level: Main Channel: Group Channel : Channel Number: AI Noise Reduction : Beep Tone : Weather Receiver: Roger Tone : CTCSS/CDCSS Code Number Press the MENU key 1 time,enter into the menu selecting mode. Press and hold the WX key for 3s,enter into the WX mode. Press key to choose the menu function.Press key to choose the menu function. Press the CALL key, call fun ction will open. Press and hold Press the GROUP key to key for 3s to lock. speak at group channel. w il l ope n . ol d lock Monitor : Keyboard Lock 16 FIRST OPERATION You need to install the battery first. Install / Removing Battery door and Belt Clip Installing Battery Door Put the battery door flat on the radio, then use a flathead screwdriver to hit the battery door screw just like the image shows on the right. Removing Battery Door Use flathead screwdriver to unscrew it to remove the battery door.Installing Belt Clip Slide the Belt clip into the slot. A “click” sound indicates the Belt Clip is locked into position. Removing Belt Clip Push the latch of belt clip in (step 1) While pushing the belt clip latch, push up the belt c lip at the same time (step 2). Battery on First Use Since batteries leave factory without a fully charging, please charge the new batteries before using. Under normal circumstances, the battery on first useneeds 5 hours of charging. When youfind out the battery is low, it is required to charge or replace it. Safety Precautions 1. Do not disassemble. 2. Do not dispose the batteries in the fire. 3. Do not dispose the batteries as household wastes, and it must becollected and treated properly. 4. Do not charge or charge battery in hazardous location. 5. Do not short-circuit the terminals. Installing Belt Clip Removing Belt Clip WARNING Please only use original accessories to prevent damage to the radio.The radio will be slightly warm during charging. Notes:1. When charging, the temperature should be between 5 ~40 ,otherwise it may cause the leakage or even damage the battery.2. Please shut down the transceiver with battery loaded before charging it. The use of the tr ansceiver while charging is ongoing will affect the normal battery charging.3. Do not charge the battery when it is wet. You should dry it first in order to avoid any danger. 4. If the battery’s usage time is very short even when it has been charged in completely correct way, it can be concludedthat the battery life is due and should be replaced by a new one. Extension of Battery life1. The performance of the battery will be reduced when the temperature drops below 0 .I Type-C charger n cold weather, it is advised to spare another battery for emergency. Please do not dispose the cold batteries that can not work at low temperature but may be usable at room temperature. 2. It may affect the normal use or charge of the battery, if it is covered with dust. Please clean the battery with dry cloth before loading or charging it. Knowledge about Battery Storage1. Since the batter y will self-discharge, please do charge it fully before putting it aside so as to prevent damages caused by over discharge. 2. Please fully charge the battery after long time storage, in order to avoid the reduction of the battery capacity resulting from over discharge. It is proposed for lithium-ion / lithium-polymer batteries to be filled in every 6 months of storage. 3. Please pay attention to the humidity of the battery storage environment. Batteries are supposed to be stored in the environment of room temperature, cool and dry air, to reduce the self-discharge. you CHARGING When the “Battery level is low, that is the icon / need to charge the battery with the enclosed -cable. Fexible Charger GENERAL OPERATIONS Before performing any operation,you need to first install the walkie talkie battery. MAKING COMMUNICATIONS The radio has main frequencies and 121 CTCSS/CDCSS codes.You can communicate with any other user who is using the same combinations, provid ing they are within range. SPEAK TO OTHER RADIO Hold the radio in a vertical position with the microphone 2.5 cm from your mouth and then speak. 4. LISTEN TO OTHER RADIO The radio will automatically sound received signal form the other radio with the same channel and code.When the main channel has received a signal, LCD shows the "M" character in green. If the GROUP channel has received a signal, LCD shows the "G" character in green. 1. POWER 2.3. ON/OFF Rotate the PWR/VOL control knob clockwise until a" ka-ka "sound is heard to turn on the power. When you receive calls ,the knob provides you the ability to change the volumefor your listening habits.When shutting down the radio,you need to rotate it counterclockwise a "ka-ka" sound is heard. When you press the PTT key, you can’t listen to other radios. Make sure you do not press PTT key for listening. Adjust volume control if necessary. 5. GROUP FUNCTION ( Dual Channel Standby and Either of Dual Channels Transmitting)The function enables the radios to monitor two channels at the same time in standby mode an…

Text truncated - open the document above for the full version.

Shenzhen Uzomi Technology Co., Ltd. 204, Taizi Industrial Zone, No. 1 Baihua Road, Laowei Village, Buji Community, Buji Subdistrict, Longgang District, Shenzhen City, Guangdong Province, China Attestation Statements Not Covered Entity Applicant & Not Covered Equipment To: Federal Communications Commission Date: Dec. 01, 2025 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(i) & (ii) FCC ID: 2BPIZ-T5G FRN: 0037043239 Shenzhen Uzomi Technology Co., Ltd. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List, established pursuant to § 1.50002 of reference chapter, as an entity producing “covered” communication equipment. The equipment for which authorization is sought is not “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List that prohibited from receiving an equipment authorization pursuant to section § 2.903 of the FCC rules. Sincerely yours, Applicant Signature Printed Name: Lyric Li Title: General Manager Address: 204, Taizi Industrial Zone, No. 1 Baihua Road, Laowei Village, Buji Community, Buji Subdistrict, Longgang District, Shenzhen City, Guangdong Province, China Tel.: 13652435277 Email: [email protected]

Shenzhen Uzomi Technology Co., Ltd. 204, Taizi Industrial Zone, No. 1 Baihua Road, Laowei Village, Buji Community, Buji Subdistrict, Longgang District, Shenzhen City, Guangdong Province, China 1 | P a g e Attestation Statements To: Federal Communications Commission Date: Dec. 01, 2025 7435 Oakland Mills Road, Columbia, MD 21046, USA Subject: Attestation of Compliance with FCC Covered List Software Requirements FCC ID: 2BPIZ-T5G Product Name: GMRS Two Way Radio This letter serves as an attestation that the equipment identified above ☐ is / ☒ is not (select one) "covered" software as defined under the Federal Communications Commission (FCC) Covered List requirements, as outlined in FCC 22-84 and KDB 986446. Specifically, the undersigned certifies that the equipment for which authorization is sought: 1. Does not contain cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors, assignees, parents, subsidiaries, affiliates, or any entity that has rebranded or relabeled software produced by the aforementioned entities. 2. Does not have the capability to store, run, or deliver any software identified on the FCC Covered List, including but not limited to cybersecurity and anti-virus software. To support this attestation, the appendix evaluation documentation has been prepared and is included in the certification filing. This attestation is based on a thorough evaluation of the device's design, functionality, and software environment. The undersigned affirms that the information provided is accurate and complete to the best of their knowledge. Sincerely yours, Applicant Signature Printed Name: Lyric Li Title: General Manager Address: 204, Taizi Industrial Zone, No. 1 Baihua Road, Laowei Village, Buji Community, Buji Subdistrict, Longgang District, Shenzhen City, Guangdong Province, China Tel.: 13652435277 Email: [email protected] Shenzhen Uzomi Technology Co., Ltd. 204, Taizi Industrial Zone, No. 1 Baihua Road, Laowei Village, Buji Community, Buji Subdistrict, Longgang District, Shenzhen City, Guangdong Province, China 2 | P a g e Evaluation regarding to the Covered List Software: Compliance Methodology Evaluation Process Results Device is Inherent compliance ☒ The Chipset(s) used is limited to run the Cybersecurity or anti-virus software. Compliance ☐ The Memory used is limited to run the Cybersecurity or anti-virus software. Compliance ☐ There is storage capacity limitation for store or install the Cybersecurity or anti-virus software. Compliance ☐ Operating system used is limited to run, install or deliver the Cybersecurity or anti-virus software. Compliance Device is not Inherent compliance ☐ Evaluation Based on Software Bill of Materials (SBoM) See attached “SBoM“ Note:The SBoM content is limited to the scope of covered list software (e.g. antivirus and cybersecurity software). ☐ Evaluation Based on Scan for Software on the device ☐ Evaluation Based on Filesystem scan ☐ Evaluation Based on Running software check

[Shenzhen Uzomi Technology Co., Ltd.] [204, Taizi Industrial Zone, No. 1 Baihua Road, Laowei Village, Buji Community, Buji Subdistrict, Longgang District, Shenzhen City, Guangdong Province, China] Date: Dec. 01, 2025 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BPIZ-T5G US Agent – Attestation Statement / Part 2.911(d)(7) [Shenzhen Uzomi Technology Co., Ltd.] certifies, that as of [Dec. 11, 2025], we have designated FCC US Agent, LLC to accept service of process on our behalf for FCC ID: 2BPIZ-T5G. [Shenzhen Uzomi Technology Co., Ltd.], accepts to maintain an agent of service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. FCC US Agent, LLC, accepts as of the date of the filing of this application, the obligation of being the designated agent for the purpose of accepting service of process on behalf of [Shenzhen Uzomi Technology Co., Ltd.] for FCC ID: 2BPIZ-T5G. Designated Agent Information: Company Name: FCC US Agent, LLC FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Contact Person: Tim Payne Phone: 708-571-3148 Email: [email protected] Sincerely, Company: [Shenzhen Uzomi Technology Co., Ltd.] FRN: 0037043239 Designated Agent: FCC US Agent, LLC Company Representative: [Lyric Li] Tel: 13652435277 Email: [email protected] Designated Agent Representative: Tim Payne Signature: Signature:

Shineconn International (Hong Kong) Co., Ltd Room 3 8/F Easey Commercial Building 253-261 Hennessy Road Wanchai HongKong, China Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Dec. 01, 2025 Subject; Request for Confidentiality FCC ID: 2BPIZ-T5G To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description Parts List Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Lyric Li Title: General Manager

Shenzhen Uzomi Technology Co., Ltd. 204, Taizi Industrial Zone, No. 1 Baihua Road, Laowei Village, Buji Community, Buji Subdistrict, Longgang District, Shenzhen City, Guangdong Province, China (Dec. 01, 2025) Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization for FCC ID: 2BPIZ-T5G I, the undersigned, hereby authorize (Attestation of Global Compliance (Shenzhen) Co., Ltd) to act on our behalf in all matters relating to this application for equipment certification. Any act carried out by (Attestation of Global Compliance (Shenzhen) Co., Ltd) shall have the same effect as our own and I acknowledge that all responsibility for complying with the terms and conditions of certification, as specified by DERYCOM CERTIFICATION SERVICES, INC., still resides with (Shenzhen Uzomi Technology Co., Ltd.). We certify that we are not subject to a denial of federal benefits that includes FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862, and that no party to the application, as defined in 47 CFR §1.2002(b), is subject to a denial of federal benefits that includes FCC benefits pursuant to that section. Sincerely, (Signature) Printed Name: Lyric Li Title: General Manager Tel.: 13652435277 Email: [email protected]

Report No.: AGC00106250937AP02 Page 1 of 4 EXTERNAL PHOTOS All View of EUT Top View of EUT Report No.: AGC00106250937AP02 Page 2 of 4 Bottom View of EUT Front View of EUT Report No.: AGC00106250937AP02 Page 3 of 4 Back View of EUT Left View of EUT Report No.: AGC00106250937AP02 Page 4 of 4 Right View of EUT Port-1 View of EUT ****************************************End of Report*************************************

FCC ID Label Location 20mm*30mm FCC ID: 2BPIZ-T5G

Report No.: AGC00106250937AP02 Page 1 of 11 INTERNAL PHOTOS Open View-1 of EUT Open View-2 of EUT Report No.: AGC00106250937AP02 Page 2 of 11 Internal View-1 of EUT Internal View-2 of EUT UHF Antenna Report No.: AGC00106250937AP02 Page 3 of 11 Internal View-3 of EUT Internal View-4 of EUT Report No.: AGC00106250937AP02 Page 4 of 11 Internal View-5 of EUT Internal View-6 of EUT Report No.: AGC00106250937AP02 Page 5 of 11 Internal View-7 of EUT Internal View-8 of EUT Report No.: AGC00106250937AP02 Page 6 of 11 Internal View-9 of EUT Internal View-10 of EUT Report No.: AGC00106250937AP02 Page 7 of 11 Internal View-11 of EUT Internal View-12 of EUT Report No.: AGC00106250937AP02 Page 8 of 11 Internal View-13 of EUT Internal View-14 of EUT Report No.: AGC00106250937AP02 Page 9 of 11 Internal View-15 of EUT Internal View-16 of EUT Report No.: AGC00106250937AP02 Page 10 of 11 Internal View-16 of EUT Internal View-17 of EUT Report No.: AGC00106250937AP02 Page 11 of 11 Internal View-18 of EUT ****************************************End of Report*************************************

Page 1 of 18 CALIBRATION DATA PROBE CALIBRATION DATA Page 2 of 18 Page 3 of 18 Page 4 of 18 Page 5 of 18 Page 6 of 18 Page 7 of 18 Page 8 of 18 Page 9 of 18 Page 10 of 18 DAE CALIBRATION DATA Page 11 of 18 Page 12 of 18 Page 13 of 18 DIPOLE CALIBRATION DATA Page 14 of 18 Page 15 of 18 Page 16 of 18 Page 17 of 18 Page 18 of 18

Page 1 of 43 SAR Test Report Report No.: AGC00106250937FH01 FCC ID : 2BPIZ-T5G PRODUCT DESIGNATION : GMRS Two Way Radio BRAND NAME : SAMCOM MODEL NAME : T5G APPLICANT : Shenzhen Uzomi Technology Co., Ltd. DATE OF ISSUE : Dec. 01, 2025 STANDARD(S) : IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2019 REPORT VERSION : V1.0 Attestation of Global Compliance(Shenzhen) Co., Ltd. Report No.: AGC00106250937FH01 Page 2 of 43 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Dec. 01, 2025 Valid Initial Release Report No.: AGC00106250937FH01 Page 3 of 43 Test Report Applicant Name Shenzhen Uzomi Technology Co., Ltd. Applicant Address 204, Taizi Industrial Zone, No. 1 Baihua Road, Laowei Village, Buji Community, Buji Subdistrict, Longgang District, Shenzhen City, Guangdong Province, China Manufacturer Name Guangdong Samzuk Technology Co, ltd Manufacturer Address High-Tech Zone Xinggong Avenue East Heyuan City (2/F of Minghuan Electrical Engineering Company Building) Factory Name Guangdong Samzuk Technology Co, ltd Factory Address High-Tech Zone Xinggong Avenue East Heyuan City (2/F of Minghuan Electrical Engineering Company Building) Product Designation GMRS Two Way Radio Brand Name SAMCOM Test Model T5G Series Model N/A Declaration of Difference N/A EUT Voltage DC 3.7V Applicable Standard IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2019 Date of receipt of test item Sep. 25, 2025 Test Date Nov. 24, 2025 Report Template AGCRT- US -PTT/SAR (2021-04-20) Note: The results of testing in this report apply to the product/system which was tested only. Prepared By Bibo Zhang (Project Engineer) Dec. 01, 2025 Reviewed By Jack Gui (Reviewer) Dec. 01, 2025 Approved By Angela Li (Authorized Officer) Dec. 01, 2025 Report No.: AGC00106250937FH01 Page 4 of 43 TABLE OF CONTENTS 1. SUMMARY OF MAXIMUM SAR VALUE ......................................................................................................... 5 2. GENERAL INFORMATION ............................................................................................................................... 6 2.1. EUT DESCRIPTION......................................................................................................................................... 6 3. SAR MEASUREMENT SYSTEM ........................................................................................................................ 7 3.1. THE DASY5 SYSTEM USED FOR PERFORMING COMPLIANCE TESTS CONSISTS OF FOLLOWING ITEMS .................... 7 3.2. DASY5 E-FIELD PROBE ................................................................................................................................. 8 3.3. DATA ACQUISITION ELECTRONICS DESCRIPTION ............................................................................................... 8 3.4. ROBOT .......................................................................................................................................................... 9 3.5. LIGHT BEAM UNIT .......................................................................................................................................... 9 3.6. DEVICE HOLDER .......................................................................................................................................... 10 3.7. MEASUREMENT SERVER ............................................................................................................................... 10 3.8. PHANTOM ................................................................................................................................................. 11 4. SAR MEASUREMENT PROCEDURE ............................................................................................................ 12 4.1. SPECIFIC ABSORPTION RATE (SAR) .............................................................................................................. 12 4.2. SAR MEASUREMENT PROCEDURE ................................................................................................................ 13 5. TISSUE SIMULATING LIQUID ....................................................................................................................... 15 5.1. THE COMPOSITION OF THE TISSUE SIMULATING LIQUID..................................................................................... 15 5.2. TISSUE DIELECTRIC PARAMETERS FOR HEAD AND BODY PHANTOMS ............................................................... 15 5.3. TISSUE CALIBRATION RESULT ....................................................................................................................... 16 6. SAR SYSTEM CHECK PROCEDURE ........................................................................................................... 17 6.1. SAR SYSTEM CHECK PROCEDURES ............................................................................................................. 17 6.2. SAR SYSTEM CHECK ................................................................................................................................... 18 7. EUT TEST POSITION ...................................................................................................................................... 19 7.1. BODY WORN POSITION ................................................................................................................................ 19 8. SAR EXPOSURE LIMITS ............................................................................................................................... 20 9. TEST FACILITY .............................................................................................................................................. 21 10. TEST EQUIPMENT LIST .............................................................................................................................. 22 11. MEASUREMENT UNCERTAINTY ............................................................…

Text truncated - open the document above for the full version.

Page 1 of 43 FCC Test Report Report No.: AGC00106250937FR01 FCC ID : 2BPIZ-T5G APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : GMRS Two Way Radio BRAND NAME : SAMCOM MODEL NAME : T5G APPLICANT : Shenzhen Uzomi Technology Co., Ltd. DATE OF ISSUE : Oct. 28, 2025 STANDARD(S) : FCC Part 95 Subpart E REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC00106250937FR01 Page 2 of 43 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Oct. 28, 2025 Valid Initial Release Report No.: AGC00106250937FR01 Page 3 of 43 Table of Contents 1. General Information ........................................................................................................................................ 5 2. Product Information ........................................................................................................................................ 6 2.1 Product Technical Description ................................................................................................................... 6 2.2 Test Frequency List ................................................................................................................................... 7 2.3 Related Submittal(S) / Grant (S) ............................................................................................................... 8 2.4 Test Methodology ...................................................................................................................................... 8 2.5 Calculation of Emission Indicators ............................................................................................................ 8 2.6 Special Accessories .................................................................................................................................. 8 2.7 Equipment Modifications ........................................................................................................................... 8 2.8 Antenna Requirement ............................................................................................................................... 9 3. Test Environment .......................................................................................................................................... 10 3.1 Address of The Test Laboratory .............................................................................................................. 10 3.2 Test Facility .............................................................................................................................................. 10 3.3 Environmental Conditions ....................................................................................................................... 11 3.4 Measurement Uncertainty ....................................................................................................................... 11 3.5 List of Equipment Used ........................................................................................................................... 12 4. System Test Configuration ........................................................................................................................... 13 4.1 EUT Configuration ................................................................................................................................... 13 4.2 EUT Exercise ........................................................................................................................................... 13 4.3 Configuration of Tested System .............................................................................................................. 13 4.4 Equipment Used in Tested System ......................................................................................................... 13 4.5 Summary of Test Results ........................................................................................................................ 14 5. Description of Test Modes ........................................................................................................................... 15 6. Frequency Stability ....................................................................................................................................... 16 6.1 Provisions Applicable .............................................................................................................................. 16 6.2 Measurement Procedure ......................................................................................................................... 16 6.3 Measurement Setup ................................................................................................................................ 16 6.4 Measurement Result ............................................................................................................................... 17 7. 26dB Emission Bandwidth and 99% Occupied Bandwidth ...................................................................... 18 7.1 Provisions Applicable .............................................................................................................................. 18 7.2 Measurement Procedure ......................................................................................................................... 18 7.3 Measurement Setup ................................................................................................................................ 18 7.4 Measurement Result ............................................................................................................................... 19 8. Spurious Radiated Emission ......................................................................................................................... 20 8.1 Provisions Applicable ......................................................................................................................…

Text truncated - open the document above for the full version.

Report No.: AGC00106250937AP01 Page 1 of 2 TEST SETUP PHOTOS Radiated Emission Test Setup Below 1GHz Radiated Emission Test Setup Above 1GHz Report No.: AGC00106250937AP01 Page 2 of 2 Conducted Test Setup ****************************************End of Report*************************************