A7C-56-100F-000WIFI BEAMFORMING ACCESS POINT

GoBeam 5100/6100 Installation Guide This page is intentionally left blank. GoBeam 5100/6100 Installation Guide i Trademarks and Licensing Agreement © 2012 GoNet Systems Ltd. All rights reserved. All information contained in this document is protected by international copyright treaties. No information may be copied or reproduced without the express written consent of GoNet Systems Ltd. GoNet Metro Broadband Wireless, GoNet GoBeam, GoNet MBW, WLAN Sector Base Station, WLS, GoNet WLAN Pico Base Station, WLP, GoNet Wireless Network Controller, and WNC are all trademarks of GoNet Systems Ltd. Any duplication, transmission by any method, or storage in an information retrieval system of any part of this publication for other purposes other than those stated above is strictly prohibited without the specific written permission of GoNet Systems Ltd. This includes, but is not limited to, transcription into any form of computer system for audio, text, print, or visual retrieval. All rights under federal copyright laws and international laws will be strictly enforced. All other trademarks and registered trademarks are the property of their respective owners. GoNet Systems Ltd. Email: [email protected] Document #: 3600-112012-2 ii GoBeam 5100/6100 Installation Guide Regulatory Information FCC-15 User Information 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 2. This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment, this equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur. To meet regulatory restrictions, the outdoor access point must be professionally installed. The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using its antennas. Any changes or modifications not expressly approved by GoNet Systems could void the user's authority to operate the equipment. The antennas used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. GoBeam 5100/6100 Installation Guide iii Notices Read and understand the following before installation. • Equipment surfaces may become hot during operation. Do not touch hot surfaces of the system. Touching a hot surface may result in serious personal injury, including burning of skin or flesh. • The GoBeam 5100/6100 is intended to be grounded. Ensure that the GoBeam 5100/6100 is connected to earth ground during normal use. • This product must be connected to a power-over- Ethernet (PoE) IEEE 802.3af compliant power source or an IEC60950 compliant limited power source. • This unit is not intended for use in marine environments. • Use 48Vdc LPS (according IEC/EN/UL 60950-1 section 2.5) power supply as power injector. iv GoBeam 5100/6100 Installation Guide Table of Contents Introduction .................................................................................. 1 GoBeam Model Numbers ............................................................ 1 GoBeam 5100 ................................................................................ 2 GoBeam 5100 Features ............................................................. 2 GoBeam 5100 Package Components ........................................... 2 GoBeam 6100 ................................................................................ 3 GoBeam 6100 Features ............................................................. 3 GoBeam 6100 Package Components ........................................... 3 GoBeam 5100/6100 Safety Information ............................................ 4 RF Exposure ............................................................................. 4 Installation Codes ..................................................................... 4 Information de sécurité pour GoBeam 5100/6100 .............................. 5 Exposition aux fréquences RF ..................................................... 5 Paratonnerre pour GoBeam 5100/6100 ....................................... 5 Codes d'installation ................................................................... 5 Installation .................................................................................... 6 Installation Process ................................................................... 6 Site Survey ........................................................................ 6 Assembling the GoBeam 5100 Antennas ...................................... 7 GoBeam 5100 Wi-Fi antennas ............................................... 7 GoBeam 5100 Mesh antennas ............................................... 8 Assembling and Mounting the GoBeam 5100/6100........................ 8 Hardware and Connectors Installation Tools .......................... 11 Mounting Adapters ............................................................. 11 Mounting Brackets .............................................................. 13 Mounting the GoBeam 5100/6100 on a horizontal pole ........... 15 Mounting the GoBeam 6100 on a vertical pole ....................... 15 Installing the Safety Cable .................................................. 16 Assembling the Optional Mesh Antennas .......................................... 17 Installation Tools ..................................................................... 19 Attaching Antenna Cables to L-Bracket ....................................... 19 Mounting the L-Bracket to the Chas…

Text truncated - open the document above for the full version.

Test Report E117580.01 GoNet Systems Ltd. Page 1 of 92 FCC ACC M Ver 1.1 05Mayl 2000 DATE: 12 September 2013 I.T.L. (PRODUCT TESTING) LTD. FCC Radio Test Report for GoNet Systems Ltd Equipment under test: WiFi BeamForming Access Point GoBeam 6100F; GoBeam 5100F Written by: _____________________________ R. Pinchuck, Documentation Approved by: _____________________________ A. Sharabi, Test Engineer Approved by: _____________________________ I. Raz, EMC Laboratory Manager This report must not be reproduced, except in full, without the written permission of I.T.L. (Product Testing) Ltd. This report relates only to items tested. *See Customer’s Declaration on page 6. Test Report E117580.01 GoNet Systems Ltd. Page 2 of 92 FCC ACC M Ver 1.1 05Mayl 2000 Measurement/Technical Report for GoNet Systems Ltd WiFi BeamForming Access Point GoBeam 6100F; GoBeam 5100F FCC ID: A7C-56-100F-000 This report concerns: Original Grant: X Class I Change: Class II Change: Equipment type: Digital Transmission System Limits used: 47CFR15 Section 15.247 Measurement procedures used are KDB 558074 D01 v03r01 April 9, 2013 and ANSI C63.4-2003. Application for Certification Applicant for this device: prepared by: (different from "prepared by") Ishaishou Raz Sharon Ashkenazi ITL (Product Testing) Ltd. GoNet Systems Ltd. Kfar Bin Nun 34 HaBarzel St. D.N. Shimshon 99780 Tel-Aviv, 69710 Israel Israel e-mail [email protected] Tel: +972-3- 633-8634 Fax: +972-3- 649-3866 e-mail: [email protected] Test Report E117580.01 GoNet Systems Ltd. Page 3 of 92 FCC ACC M Ver 1.1 05Mayl 2000 TABLE OF CONTENTS 1. GENERAL INFORMATION ------------------------------------------------------------------------------- 5 1.1 Administrative Information ................................................................................. 5 1.2 List of Accreditations ......................................................................................... 7 1.3 Product Description ........................................................................................... 8 1.4 Test Methodology .............................................................................................. 8 1.5 Test Facility ....................................................................................................... 9 1.6 Measurement Uncertainty ................................................................................. 9 2. SYSTEM TEST CONFIGURATION --------------------------------------------------------------------10 2.1 Justification ...................................................................................................... 10 2.2 EUT Exercise Software ................................................................................... 10 2.3 Special Accessories ........................................................................................ 10 2.4 Equipment Modifications ................................................................................. 10 2.5 Configuration of Tested System ...................................................................... 11 3. CONDUCTED AND RADIATED MEASUREMENT TEST SET-UP PHOTOS --------------12 4. POWER LINES CONDUCTED EMISSION ----------------------------------------------------------17 4.1 Test Specification ............................................................................................ 17 4.2 Test Procedure ................................................................................................ 17 4.3 Test Results..................................................................................................... 17 4.4 Test Equipment Used, Power Lines Conducted Emission .............................. 22 5. 6 DB MINIMUM BANDWIDTH --------------------------------------------------------------------------23 5.1 Test Specification ............................................................................................ 23 5.2 Test Procedure ................................................................................................ 23 5.3 Test Results..................................................................................................... 24 5.4 Test Equipment Used, 6dB Minimum Bandwidth ............................................ 28 6. 26 DB MINIMUM BANDWIDTH-------------------------------------------------------------------------29 6.1 Test Specification ............................................................................................ 29 6.2 Test Procedure ................................................................................................ 29 6.3 Test Results..................................................................................................... 30 6.4 Test Equipment Used, 26 dB Minimum Bandwidth ......................................... 34 7. MAXIMUM TRANSMITTED PEAK POWER OUTPUT -------------------------------------------35 7.1 Test Specification ............................................................................................ 35 7.2 Test Procedure ................................................................................................ 35 7.3 Test Results..................................................................................................... 35 7.4 Test Equipment Used, Maximum Peak Power Output .................................... 40 8. PEAK POWER OUTPUT OUT OF 2400-2483.5 MHZ BAND -----------------------------------41 8.1 Test Specification ............................................................................................ 41 8.2 Test Procedure ................................................................................................ 41 8.3 Test Results..................................................................................................... 41 8.4 Test Equipment Used, Peak Power Output Out of 2400-2483.5 MHz Band .. 48 9. BAND EDGE ------------------------------------------------------------------------------------------------49 9.1 Test Specification ..…

Text truncated - open the document above for the full version.