A7M-79715Mount MagSafe Car Vent

Name Mount MagSafe Car Vent Item Number 79715 /8098433 FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected... Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC'S RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Shenzhen Reflying Electronic Co., Ltd. 2023.07.03 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for FCC ID: A7M-79715 Shenzhen Reflying Electronic Co., Ltd. certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Applicant signature: Applicant printed name: Wen Luo / Manager Shenzhen Reflying Electronic Co., Ltd. 2023.07.03 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for FCC ID: A7M-79715 Shenzhen Reflying Electronic Co., Ltd. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Applicant signature: Applicant printed name: Wen Luo / Manager

Shenzhen Reflying Electronic Co., Ltd. 2023.07.03 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: CONFIDENTIALITY REQUEST FOR EUT NAME: Mount MagSafe Car Vent MODEL : RST97C, 79715, 8098433 FCC ID: A7M-79715 To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the - Block Diagram - Schematics - Operational Description required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, Client’s signature: Client’s name / title : Wen Luo / Manager Contact information / address: 6 Bldg., Gaoxinjian Industrial Zone, Heping Villag Fuyong Town, Bao'an District, Shenzhen, Guangdong, China

Shenzhen Reflying Electronic Co., Ltd. 2023.07.03 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen BCTC Testing Co., Ltd to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Client’s signature: Client’s name / title : Wen Luo / Manager Contact information / address: 6 Bldg., Gaoxinjian Industrial Zone, Heping Villag Fuyong Town, Bao'an District, Shenzhen, Guangdong, China

Shenzhen Reflying Electronic Co., Ltd. Model Difference 2023-07-03 EUT NAME: Mount MagSafe Car Vent MODEL : RST97C, 79715, 8098433 FCC ID: A7M-79715 All the model are the same circuit and RF module, except model names. Regards Sincerely Client’s signature: Client’s name / title : Wen Luo / Manager Contact information / address: 6 Bldg., Gaoxinjian Industrial Zone, Heping Villag Fuyong Town, Bao'an District, Shenzhen, Guangdong, China

External Photos

Size:10*5mm FCC ID: A7M-79715 Label Location

Internal Photos Antenna

No.：BCTC/RF-EMC-005 Page 1 of 14 Edition：B.0 TEST REPORT Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC2306254498-2E Applicant: Shenzhen Reflying Electronic Co., Ltd. Product Name: Mount MagSafe Car Vent Model/Type reference: RST97C Tested Date: 2023-06-28 to 2023-07-01 Issued Date: 2023-07-03 Report No.: BCTC2306254498-2E No.：BCTC/RF-EMC-005 Page 2 of 14 Edition：B.0 FCC ID: A7M-79715 The test report is effective only with both signature and specialized stamp.This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Testing Co., Ltd, this report can’t be reproduced except in full.The tested sample(s) and the sample information are provided by the client. Product Name: Mount MagSafe Car Vent Trademark: Reflying, Mangotek, ATIVA Model/Type reference: RST97C 79715, 8098433 Prepared For: Shenzhen Reflying Electronic Co., Ltd. Address: 6 Bldg., Gaoxinjian Industrial Zone, Heping Villag Fuyong Town, Bao'an District, Shenzhen, Guangdong, China Manufacturer: Shenzhen Reflying Electronic Co., Ltd. Address: 6 Bldg., Gaoxinjian Industrial Zone, Heping Villag Fuyong Town, Bao'an District, Shenzhen, Guangdong, China Prepared By: Shenzhen BCTC Testing Co., Ltd. Address: 1-2/F., Building B, Pengzhou Industrial Park, No.158, Fuyuan 1st Road, Zhancheng, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, China Sample Received Date: 2023-06-27 Sample tested Date: 2023-06-28 to 2023-07-01 Issue Date: 2023-07-03 Report No.: BCTC2306254498-2E Test Standards: FCC CFR 47 part1, 1.1307(b), 1.1310 Test Results: PASS Tested by: Approved by: Eric Yang/Project Handler Zero Zhou/Reviewer Report No.: BCTC2306254498-2E No.：BCTC/RF-EMC-005 Page 3 of 14 Edition：B.0 Table Of Content Test Report Declaration Page 1. Version .................................................................................................................. 4 2. Product Information ............................................................................................... 5 2.1 Product Information ............................................................................................... 5 2.2 Support Equipment ............................................................................................... 5 2.3 Test Mode ............................................................................................................. 5 3. Test Facility And Test Instrument Used ................................................................. 6 3.1 Test Facility ........................................................................................................... 6 3.2 Test Instrument Used ............................................................................................ 6 4. Method Of Measurement ....................................................................................... 7 4.1 Applicable Standard .............................................................................................. 7 4.2 Block Diagram Of Test Setup ................................................................................ 7 4.3 Limit ...................................................................................................................... 8 4.4 Test procedure ...................................................................................................... 8 4.5 Equipment Approval Considerations ..................................................................... 9 4.6 E and H field Strength ......................................................................................... 10 5. Photographs Of Test Set-Up ............................................................................... 11 (Note: N/A Means Not Applicable) Report No.: BCTC2306254498-2E No.：BCTC/RF-EMC-005 Page 4 of 14 Edition：B.0 1. Version Report No. Issue Date Description Approved BCTC2306254498-2E 2023-07-03 Original Valid Report No.: BCTC2306254498-2E No.：BCTC/RF-EMC-005 Page 5 of 14 Edition：B.0 2. Product Information 2.1 Product Information Model/Type reference: RST97C 79715, 8098433 Model differences: All the model are the same circuit and RF module, except model names. Operation Frequency: 115kHz-205kHz Modulation type: ASK Antenna installation: Coil antenna Ratings: DC 5V/9V From Adapter Wireless charger Output: 5W, 7.5W, 10W 2.2 Support Equipment Device Type Brand Model Series No. Note E-2 Dummy load N/A DL01 N/A E-3 Adapter N/A HW-110600C02 N/A Notes: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. 2.3 Test Mode Test Mode keeping TX+Charging mode Report No.: BCTC2306254498-2E No.：BCTC/RF-EMC-005 Page 6 of 14 Edition：B.0 3. Test Facility And Test Instrument Used 3.1 Test Facility All measurement facilities used to collect the measurement data are located at Shenzhen BCTC Testing Co., Ltd. Address:1-2/F., Building B, Pengzhou Industrial Park, No.158, Fuyuan 1st Road, Zhancheng, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, China. The site and apparatus are constructed in conformance with the requirements of ANSI C63.4 and CISPR 16-1-1 other equivalent standards. FCC Test Firm Registration Number: 712850 FCC Designation Number: CN1212 ISED Registered No.: 23583 ISED CAB identifier: CN0017 3.2 Test Instrument Used EMF Test Equipment Manufacturer Model# Serial# Last Cal. Next Cal. Electromagnet -ic radiation tester Wavecontrol SMP160 19SN0980 May 15, 2023 May 14, 2024 Electromagnet -ic field probe Wavecontrol WP400-3 20WP120082 Sept. 08, 2022 Sept. 07, 2023 843 Chamber ETS 843 84301 Aug. 27, 2020 Aug. 26, 2023 Software Frad EZ-EMC EMC-CON 3A1 \ \ Report No.: BCTC2306254498-2E No.：BCTC/RF-EMC-005 Page 7 of 14 Edition：B.0 4. Method Of Measurement 4.1 Applicable Standard According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensure…

Text truncated - open the document above for the full version.

No.：BCTC/RF-EMC-005 Page 1 of 24 Edition：B.0 TEST REPORT Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC2306254498-1E Applicant: Shenzhen Reflying Electronic Co., Ltd. Product Name: Mount MagSafe Car Vent Model/Type reference: RST97C Tested Date: 2023-06-28 to 2023-07-01 Issued Date: 2023-07-03 Report No.: BCTC2306254498-1E No.：BCTC/RF-EMC-005 Page 2 of 24 Edition：B.0 FCC ID: A7M-79715 The test report is effective only with both signature and specialized stamp.This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Testing Co., Ltd, this report can’t be reproduced except in full.The tested sample(s) and the sample information are provided by the client. Product Name: Mount MagSafe Car Vent Trademark: Reflying, Mangotek, ATIVA Model/Type reference: RST97C 79715, 8098433 Prepared For: Shenzhen Reflying Electronic Co., Ltd. Address: 6 Bldg., Gaoxinjian Industrial Zone, Heping Villag Fuyong Town, Bao'an District, Shenzhen, Guangdong, China Manufacturer: Shenzhen Reflying Electronic Co., Ltd. Address: 6 Bldg., Gaoxinjian Industrial Zone, Heping Villag Fuyong Town, Bao'an District, Shenzhen, Guangdong, China Prepared By: Shenzhen BCTC Testing Co., Ltd. Address: 1-2/F., Building B, Pengzhou Industrial Park, No.158, Fuyuan 1st Road, Zhancheng, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, China Sample Received Date: 2023-06-27 Sample tested Date: 2023-06-28 to 2023-07-01 Issue Date: 2023-07-03 Report No.: BCTC2306254498-1E Test Standards: FCC Part15.209 ANSI C63.10-2013 Test Results: PASS Tested by: Approved by: Eric Yang/Project Handler Zero Zhou/Reviewer Report No.: BCTC2306254498-1E No.：BCTC/RF-EMC-005 Page 3 of 24 Edition：B.0 Table Of Content Test Report Declaration Page 1. Version .................................................................................................................. 4 2. Test Summary ....................................................................................................... 5 3. Measurement Uncertainty ..................................................................................... 6 4. Product Information And Test Setup ..................................................................... 7 4.1 Product Information ............................................................................................... 7 4.2 Test Setup Configuration ...................................................................................... 7 4.3 Support Equipment ............................................................................................... 8 4.5 Test Mode ............................................................................................................. 8 5. Test Facility And Test Instrument Used ................................................................. 9 5.1 Test Facility ........................................................................................................... 9 5.2 Test Instrument Used ............................................................................................ 9 6. Conducted Emissions .......................................................................................... 11 6.1 Block Diagram Of Test Setup .............................................................................. 11 6.2 Limit .................................................................................................................... 11 6.3 Test procedure .................................................................................................... 11 6.4 EUT operating Conditions ................................................................................... 11 6.5 Test Result .......................................................................................................... 12 7. Radiated Emissions ............................................................................................. 14 7.1 Block Diagram Of Test Setup .............................................................................. 14 7.2 Limit .................................................................................................................... 15 7.3 Test procedure .................................................................................................... 15 7.4 Test Result .......................................................................................................... 16 8. Bandwidth Test .................................................................................................... 19 8.1 Test Procedure ................................................................................................... 19 8.2 Test Setup ........................................................................................................... 19 8.3 Test Result .......................................................................................................... 19 9. Antenna Requirements ........................................................................................ 20 9.1 Limit .................................................................................................................... 20 9.2 Test Result .......................................................................................................... 20 10. EUT Photographs ................................................................................................ 21 11. EUT Test Setup Photographs.............................................................................. 22 (Note: N/A Means Not Applicable) Report No.: BCTC2306254498-1E No.：BCTC/RF-EMC-005 Page 4 of 24 Edition：B.0 1. Version Report No. Issue Date Description Approved BCTC2306254498-1E 2023-07-03 Original Valid Report No.: BCTC2306254498-1E No.：BCTC/RF-EMC-005 Page 5 of 24 Edition：B.0 2. Test Summary The Product has been tested according to the following specifications: No. Test Parameter Clause No. Results 1 Conducted Emission 15.207 PASS 2 Radiated Emission 15.209 PASS 3 20dB…

Text truncated - open the document above for the full version.

客 户 名 称 ： CUSTOMER`S NAME 客 户 料 号 ： CUSTOMER`S P/N 产 品 规 格 ： PRODUCT SPEC 制 作 日 期 ： ISSUE DATE 审核 CHECKED BY 承 认 书 SPECIFICATION FOR APPROVAL 2023年7月4日 拟制 PREPARED BY Y.A11.216 批准 APPROVED BY 客户承认 CUSTOMER APPROVE Manufa cturer: Add： Tel： Fax： *本承认书请在首批下单生产此机种前回签，否则视为贵方默认此承认书内所有内容* A118 Goldman Sachs Tower,No. 18 Central Road, Shajing Street, Bao'an District, Shenzhen 188 2097 0736 Shenzhen Qxwic Technology Co., Ltd CUSTOMERCUSTOMER`S P/N0 ISSUE DATEPRODUCT SPECY.A11.216 SPECIFICATION CONTROL DRAWING REVISIONS REVDESCRIPTIONDATEISSUE BYAPPROVAL BY 李博文 A INITIAL2023年7月4日 李蓓 1.MATERIAL: NOUL FILE NO CUSTOMERCUSTOMER`S P/N0 ISSUE DATEPRODUCT SPEC Y.A11.216 ITEMTYPESUPPLIERS 1 2 3 4 5 6 / 双面胶/double-side tape / 电子黄胶/yellow glue 锡/tin / / / 磁片/magnetic separator 高温胶带/high temperature tape Sn99.3:Cu0.7 BE885-9007 42*0.1 0.025*8 BTL BR DL YH MnZn-Ferrite G43.5*5.2*T0.8 LX 线材/wire [email protected]*100P AG/ 2.DIMENSION： CUSTOMER 0CUSTOMER`S P/N0 ISSUE DATE2023年7月4日PRODUCT SPECY.A11.216 ISSUECHECKAPPROVAL BYBYBY 4.CIRCUIT DIAGRAM 5.WINDING NO N1 CUSTOMERCUSTOMER`S P/N0 ISSUE DATE2023年7月4日PRODUCT SPECY.A11.216 WINDINGWIRETURNSTAPEWINDING CONDITION S-FØ0.07*100P 10 / CCW 6.CHARACTERISTIC ITEMMEASURED POINTTECHNICAL DATATESTING CONDITION & INSTRUMENT LSS-F6.5uH±5% LCR1062 100KHz/1V AT 25°C±2°C 7.THE PACKING WAY CUSTOMER0CUSTOMER`S P/N0 ISSUE DATE2023年7月4日PRODUCT SPECY.A11.216

Conducted emissions Radiated Measurement Photos