A7M-RWC739AWireless Watch Charger

FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. FCC 卡 size：80x90mm， 材质：128G双铜单黑过光油

1/1 USAgentforServiceofProcessLETTEROFATTESTATION TO: OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USAgentforServiceofProcess: CompanyName:HOPEKCORPORATIONINC Address:16755CoyoteBushDrUnit84,SanDiego,CA92127UnitedStates FRN:0034562900 ContactName:YangyangXu TelephoneNo:(561)875-9826 E-mail:[email protected] ThisletteristoconfirmthattheUSAgentforServiceofProcessacceptsresponsibilitytoactas alocalrepresentativeonbehalfofShenzhenReflyingElectronicCo.,Ltd. TheUSAgentforServiceofProcessisawareofandagreestocomplywiththerequirements outlinedintheFCCEquipmentAuthorizationProgram,ReportandOrderFCC22-84,andclause §2.911. Applicant: CompanyName:ShenzhenReflyingElectronicCo.,Ltd. ProductDescription:WirelessWatchCharger FRN:0021357322 GranteeCode:A7M FCCID:A7M-RWC739A ContactName:WenLuo Address:2/F,Building4,201-501,BuildingB6,GaoxinjianIndustrialPark,Fuyuan1stRoad, HepingCommunity,FuhaiSubdistrict,Bao'anDistrict,Shenzhen,China TelephoneNo:(86)755-26718925 E-mail:[email protected] TheApplicantisawareofandagreestocomplywiththerequirementsoutlinedintheFCC EquipmentAuthorizationProgram,ReportandOrderFCC22-84,andclause§2.911. ThisAgreementisvaliduntil(Permanentlyvalid). Date:2026/9/5 Applicant’sName: ShenzhenReflyingElectronicCo.,Ltd. USAgentforServiceofProcess’sName: HOPEKCORPORATIONINC Title:ManagerTitle:Manager SignatureSignature

Rev 1/26/2023 Shenzhen Reflying Electronic Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Sept. 05, 2026 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: A7M-RWC739A [Shenzhen Reflying Electronic Co., Ltd.] certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [Shenzhen Reflying Electronic Co., Ltd.] certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, (Applicant signature) (Applicant printed name) Wen Luo Rev 1/26/2023 Shenzhen Reflying Electronic Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Sept. 05, 2026 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: A7M-RWC739A [Shenzhen Reflying Electronic Co., Ltd.] certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Wen Luo

Shenzhen Reflying Electronic Co., Ltd. Family models declaration letter Sept. 05, 2026 We Shenzhen Reflying Electronic Co., Ltd. Of 2/F, Building 4, 201-501, Building B6, Gaoxinjian Industrial Park, Fuyuan 1st Road, Heping Community, Fuhai Subdistrict, Bao’an District, Shenzhen, China Declare under our sole responsibility that the product FCC ID: A7M-RWC739A Product: Wireless Watch Charger Model Number: RWC739A, RWC739A/CB104 All the models are the same circuit and module, except the model No.. Wen Luo/ Manager E-mail : [email protected] Phone : (86) 755-26718925 Fax : (86) 755-26718815 Address : 2/F, Building 4, 201-501, Building B6, Gaoxinjian Industrial Park, Fuyuan 1st Road, Heping Community, Fuhai Subdistrict, Bao’an District, Shenzhen, China

Shenzhen Reflying Electronic Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: September 10, 2026 Subject; Request for Confidentiality FCC ID: A7M-RWC739A To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements for UNII devices In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Wen Luo Title: Manager

Effective Date: April 2, 2020 QSF 7.6.4-8 – Agent Authorization Letter Template Page 1 of 1 Revision Date: Revision: 0 Shenzhen Reflying Electronic Co., Ltd. Date: Sept. 05, 2026 Product Model Number: RWC739A, RWC739A/CB104 FCC ID: A7M-RWC739A To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following:  Testing  Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. By: Contact Listed on FCC Wesbite Title: Manager Email: [email protected] Telephone: (86) 755-26718925 On behalf of: Shenzhen Reflying Electronic Co., Ltd.

Ext Photos Model: RWC739A Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6

Wireless Watch Charger Model: RWC739A/CB104 Lot#82464 USB-C Input: 5.0V 1.0A(5.0W) Wireless Output: 2.5W Max FCC ID: A7M-RWC739A Made in China

Int Photos Model: RWC739A Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7 Photo 8 Photo 9 Photo 10 ANT

- Page 1 of 10 - Report No.: HB20260826002E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com RF EXPOSURE Test Report Product: Wireless Watch Charger Trade Mark: N/A Model Number: RWC739A FCC ID: A7M-RWC739A Prepared for Shenzhen Reflying Electronic Co., Ltd. 2/F, Building 4, 201-501, Building B6, Gaoxinjian Industrial Park, Fuyuan 1st Road, Heping Community, Fuhai Subdistrict, Bao'an District, Shenzhen, China Prepared by Shenzhen HongBiao Certification& Testing Co., Ltd Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen, China Tel.: +86-755-2998 9321 Fax.: +86-755-2998 5110 Website: http://www.sz-hongbiao.com - Page 2 of 10 - Report No.: HB20260826002E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Table of Contents 1 GENERAL DESCRIPTION ..................................................................................................................................... 5 1.1 DESCRIPTION OF EUT ................................................................................................................................................ 5 1.2 TEST MODE .............................................................................................................................................................. 5 1.3 TEST SETUP .............................................................................................................................................................. 5 1.4 ANCILLARY EQUIPMENT .............................................................................................................................................. 5 2 TEST FACILITIES AND ACCREDITATIONS .............................................................................................................. 6 2.1 TEST LABORATORY ..................................................................................................................................................... 6 2.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 6 2.3 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 6 2.4 TEST SOFTWARE ........................................................................................................................................................ 6 3 LIST OF TEST EQUIPMENT .................................................................................................................................. 7 4 RF EXPOSURE..................................................................................................................................................... 8 4.1 MAXIMUM PERMISSIBLE EXPOSURE .............................................................................................................................. 8 4.1.1. Limit ............................................................................................................................................................ 8 4.1.2. Test Procedures ........................................................................................................................................... 8 4.1.3. Test Setup .................................................................................................................................................... 8 4.1.4. Test Result ................................................................................................................................................... 8 5 PHOTOGRAPHS OF THE TEST SETUP ..................................................................................................................10 - Page 3 of 10 - Report No.: HB20260826002E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com TEST RESULT CERTIFICATION Applicant’s Name ................. : Shenzhen Reflying Electronic Co., Ltd Address ................................. : 2/F, Building 4, 201-501, Building B6, Gaoxinjian Industrial Park, Fuyuan 1st Road, Heping Community, Fuhai Subdistrict, Bao'an District, Shenzhen, China Manufacturer's Name .......... : Shenzhen Reflying Electronic Co., Ltd Address ................................. : 2/F, Building 4, 201-501, Building B6, Gaoxinjian Industrial Park, Fuyuan 1st Road, Heping Community, Fuhai Subdistrict, Bao'an District, Shenzhen, China Product description Product name ........................ : Wireless Watch Charger Model Number ....................... : RWC739A Standards ............................. : FCC CFR 47 PART 1 , 1.1310 Test procedure ....................... : KDB 680106 D01 Wireless Power Transfer v04 This device described above has been tested by Shenzhen HongBiao Certification& Testing Co., Ltd and the test results show that the equipment under test (EUT) is in compliance with the EMC requirements. And it is applicable only to the tested sample identified in the report. Date of Test ........................................... : Date (s) of performance of tests ............. : Aug. 28, 2026~Sept. 04, 2026 Test Result .............................................. : Pass Testing Engineer : ( Z o e Su) Technical Manager : (M i n g L i u) Authorized Signatory : (L e o S u) - Page 4 of 10 - Report No.: HB20260826002E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street…

Text truncated - open the document above for the full version.

SPECIFICATIONS SHEE Huizhou Qitai Electronic Technology Co., LTD T ZLGD-A1-049 ZhongliGuanda(Shenzhen)Intelligent TechnologyCO., CUSTOMER : DESCRIPTION : CUSTOMER P/N : PART NUMBER : DATE OF APPLICATION : Ltd 3 2026-8-26 CLASSIFICATION OF SPEC. PRESENTATION. ( Tick the relevant box "√" ) oNew application √New part is added to accepted specification oRevision of accepted specification ACCEPTANCE STAMP APPROVAL BYCHECK BYPREPARE BY ADDRESS :3rd Floor, No. 181, Mingyue 2nd Road, Shiwan Town, Boluo County, Huizhou city TELPHONE :0752-6668681 E-MAIL :[email protected] zhao ziqi Feng xin History For Revised Specificatio Huizhou Qitai Electronic Technology Co., LTD n CUSTOMER P/N : PART NUMBER : ZLGD-A1-0493 DESCRIPTION ( Content Or Reason For Changed ) Rev. Cust Rev. Item Date Revisor 1 A Initial Release 0 冯 2026-8-26 欣 APPROVED BYCHECKED BYPREPARED BY 晁子 DATEPAGE 奇 冯欣 1 of 2026-8-26 3 Feng xin Zhao ziqi Feng xin Huizhou Qitai Electronic Technology Co., LTD Specification CUSTOMER P/N : PART NUMBER : ZLGD-A1-0493 1. DIMENSIONS : Unit: mm Unit：mm ABCDEG 21Max 14.5±0.5 7.5±0.58±12±12..2±0. F 2.7Refx 1 1.This product Apply a φ18 mm pure white adhesive backing 2.Magnet specifications：φ7.5*2.2，Magnetic field force（3000GS±100GS）。 3.Groove at the soft magnetic lead-out point。 APPROVED BYCHECKED BYPREPARED BYDATEPAGE 2 of 2026-8-26 3 Zhao ziqi Feng xin Huizhou Qitai Electronic Technology Co., LTD Specification CUSTOMER P/N : PART NUMBER : ZLGD-A1-0493 2. WINDING DETAILS Coil1 TurnsWire Dia 15T Wdg.Direction Intersect Yes/Not S Wdg. Type Spred/Close 0. 08*24P Hot Air stranded Wire（red） Close Reverse winding Yes 3. ELECTRICAL CHARACTERISTICS: TEMPERATURE:25±10, RELATIVE HUMIDITY:6510% NO. ITEMTERMINALSPECIFICATION Coil TEST FREQUENCYTEST EQUIPMENTS 1 1.INDS-F 10.5uh±0.3uh 100kHz/VUC2906A 2. QS-F 25Min 100kHz/VUC2906A 3.DCRS-F 150Max 100kHz/VUC2906A APPROVED BYCHECKED BY PREPARED BYDATE PAGE 3 of 2026-8-26 3 Zhao ziqi Feng xin

- Page 1 of 32 - Report No.: HB20260826002E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Test Report Product: Wireless Watch Charger Trade Mark: N/A Model Number: RWC739A FCC ID: A7M-RWC739A Prepared for Shenzhen Reflying Electronic Co., Ltd. 2/F, Building 4, 201-501, Building B6, Gaoxinjian Industrial Park, Fuyuan 1st Road, Heping Community, Fuhai Subdistrict, Bao'an District, Shenzhen, China Prepared by Shenzhen HongBiao Certification& Testing Co., Ltd Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen, China Tel.: +86-755-2998 9321 Fax.: +86-755-2998 5110 Website: http://www.sz-hongbiao.com - Page 2 of 32 - Report No.: HB20260826002E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Table of Contents 1 GENERAL DESCRIPTION ..................................................................................................................................... 5 1.1 DESCRIPTION OF EUT ................................................................................................................................................ 5 1.2 TEST MODE .............................................................................................................................................................. 5 1.3 TEST SETUP .............................................................................................................................................................. 5 1.4 POWER SETTING CONFIGURATION PARAMETERS ............................................................................................................... 6 1.5 ANCILLARY EQUIPMENT .............................................................................................................................................. 6 2 SUMMARY OF TEST RESULT ............................................................................................................................... 7 3 TEST FACILITIES AND ACCREDITATIONS .............................................................................................................. 8 3.1 TEST LABORATORY ..................................................................................................................................................... 8 3.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 8 3.3 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 8 3.4 TEST SOFTWARE ........................................................................................................................................................ 9 4 LIST OF TEST EQUIPMENT .................................................................................................................................10 5 TEST ITEM AND RESULTS ...................................................................................................................................12 5.1 ANTENNA REQUIREMENT .......................................................................................................................................... 12 5.2 CONDUCTED EMISSION ............................................................................................................................................. 13 5.3 RADIATED EMISSION ................................................................................................................................................ 17 5.4 OCCUPIED BANDWIDTH ............................................................................................................................................ 22 6 PHOTOGRAPHS OF THE TEST SETUP ..................................................................................................................23 7 PHOTOGRAPHS OF THE EUT..............................................................................................................................25 - Page 3 of 32 - Report No.: HB20260826002E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com TEST RESULT CERTIFICATION Applicant’s Name ................. : Shenzhen Reflying Electronic Co., Ltd Address ................................. : 2/F, Building 4, 201-501, Building B6, Gaoxinjian Industrial Park, Fuyuan 1st Road, Heping Community, Fuhai Subdistrict, Bao'an District, Shenzhen, China Manufacturer's Name .......... : Shenzhen Reflying Electronic Co., Ltd Address ................................. : 2/F, Building 4, 201-501, Building B6, Gaoxinjian Industrial Park, Fuyuan 1st Road, Heping Community, Fuhai Subdistrict, Bao'an District, Shenzhen, China Product description Product name ........................ : Wireless Watch Charger Model Number ....................... : RWC739A Standards ............................. : FCC Part 15C Test procedure ....................... : IEEE/ANSI C63.10-2020 + Cor. 1-2023 + C63.10a-2024 + Errata to C63.10a-2024 This device described above has been tested by Shenzhen HongBiao Certification& Testing Co., Ltd and the test results show that the equipment under test (EUT) is in compliance with the EMC requirements. And it is applicable only to the tested sample identified in the report. Date of Test ........................................... : Date (s) of performance of tests ............. : Aug. 28, 2026~Sept. 04, 2026 Test Result .................…

Text truncated - open the document above for the full version.

- Page 1 of 2 - Photographs of the Test Setup Model: RWC739A Radiated Emission Below 30MHz Radiated Emission Above 30MHz - Page 2 of 2 - Conducted emission MPE