A7MASOUND-66Siliphone Cling BT Speaker

cate Of Conformity (warranty Card)1 Piece 40mm This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Shenzhen Reflying Electronic Co.,Ltd Authority to Act as Agent Date: _2013-1-31 American Certific ation Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch is authorized to act on our behalf, until ot herwise notified, fo r applications to American Certification Body, Inc. (ACB). We certi fy that we are not subject to denial of federal benefits, th at in cludes FCC benefits, purs uant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defin ed in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that inclu des FCC benefits. Thank you, Agency Agreemen t Expiration Date: ___12 months_____ By: __________________________ ________________________ (Signature 1 Title: ___manager On behalf of: _ Shenzhen Reflyin g Electronic Co.,Ltd (Company Name) Telephone: _+86 7 55 26718925 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent let ter has been pr ovid ed. Letter s should be pl aced on ap prop riat e letter head. ) (Print name)

Shenzhen Reflyin g Electronic Co.,Ltd Request for Confidentiality Date: _ 2013-01-31 Subject: Confid en tiality Req ues t for: ____A7MASOUND-66____ Pursuant to FCC 47 CRF 0.457(d) an d 0. 459 an d IC RSP-100, Section 10, th e applicant reques ts th at a part of the su bject FCC application be held confidenti al. Type of Confidential ity Requested Exhibit Shor t Term Permanent Block Diagr ams Short Term External Photos Shor t Term Permanent* 1 Internal Photos Shor t Term Permanent Operation Description/Theory of Operation Shor t Term Permane nt Parts List & Placement/BOM Shor t Term Permanent Tune-Up Proc ed ure Shor t Term Permanent Schematics Shor t Term Test Setup Phot os Shor t Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary) ______ _ Shenzhen Reflying Elec tronic Co.,Ltd____ has spent sub stantial effort in developing this product and it is one of the first of its kind in industry. Having th e subject information ea sily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confident ial be permanently withheld from public review due to materials th at contain trade secrets and propriet ary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180 ) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marke ting or release of the product to the public. Applicant is also aware that they are responsible to noti fy ACB in th e event information regarding the pr od uct or the pr oduct is made available to the public. ACB will then release the documents listed above fo r public disclosure pursuant to FCC Public Noti ce DA 04-170 5. NOTE for Industry Canada Applications: The ap plicant un derstands that until such time that IC distinguishes between Short Term an d Permanent Confidentiality, eit her type of marked exhibit above will simply be marked Confide ntial when submitted to IC. Sincerely, By: __ ___________________ (Signature/Title 3 ) (Print na me) 1 - The asterisked ite ms (*) req uire fu rther justificatio n be fore per manent co nf id entiality will be allowed. Thes e also currently require review by the FCC under th eir Permit-But- Ask po licy before the grant is issued and can delay co mplet ion of an ap plicat ion. Further justification should be added to the no te ab ove. One such example for a potted device woul d be: “The EUT is FULLY potted using a non-remova ble ep oxy based material. Remova l of potting material ca uses irr eparable damag e to inte rnal circu itry. See photographs exhibits that outli ne the device be fore and af ter pott ing.” 2 - Pleas e refer to ht tp:/ /acbcert.com/documents/misc-docs/Memo-Short-Ter m-Vs-Standard-Confident ia lit y.p df for co mplete details. 3 - Must be signed by applicant contact giv en for applicant on the FCC sit e, or by the author ized ag ent if an ap prop riate au thorized agent letter has been provided. Letter s should be placed on ap propriate letter he ad.

1 Photographs - EUT Constructional Details (Test Model No.: Asound-66)

1 Photographs - EUT Constructional Details (Test Model No.: Asound-66)

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM130200078404 Page: 1 of 5 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page SAR Evaluation Report Application No.: SZEM1302000784RF Applicant: Shenzhen Reflying Electronic Co., Ltd Manufacturer: Shenzhen Reflying Electronic Co., Ltd Factory: Shenzhen Reflying Electronic Co., Ltd Product Name: Siliphone Cling BT Speaker Model No.(EUT): Asound-66 Add Model No.: 840042, 840043, 840044, 840045, 840046 FCC ID: A7MASOUND-66 Standards: 47 CFR Part 1.1307(2012) 47 CFR Part 2.1093 (2012) KDB447498D01 General RF Exposure Guidance v05 Date of Receipt: 2013-02-22 Date of Test: 2013-02-27 to 2013-04-09 Date of Issue: 2013-04-17 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM130200078404 Page: 2 of 5 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Contents Page 1 COVER PAGE ..................................................................................................................................................... 1 2 CONTENTS ......................................................................................................................................................... 2 3 GENERAL INFORMATION ................................................................................................................................ 3 3.1 CLIENT INFORMATION ......................................................................................................................................... 3 3.2 GENERAL DESCRIPTION OF EUT .......................................................................................................................... 3 3.3 TEST LOCATION .................................................................................................................................................. 4 3.4 TEST FACILITY.................................................................................................................................................... 4 3.5 DEVIATION FROM STANDARDS ............................................................................................................................. 4 3.6 ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................................... 4 3.7 OTHER INFORMATION REQUESTED BY THE CUSTOMER .......................................................................................... 4 4…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM130200078403 Page: 1 of 47 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No.: SZEM1302000784RF Applicant: Shenzhen Reflying Electronic Co., Ltd Manufacturer: Shenzhen Reflying Electronic Co., Ltd Factory: Shenzhen Reflying Electronic Co., Ltd Product Name: Siliphone Cling BT Speaker Model No.(EUT): Asound-66 Add Model No.: 840042, 840043, 840044, 840045, 840046 FCC ID: A7MASOUND-66 Standards: 47 CFR Part 15, Subpart C (2012) Date of Receipt: 2013-02-22 Date of Test: 2013-02-27 to 2013-04-09 Date of Issue: 2013-04-17 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM130200078403 Page: 2 of 47 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203/15.247 (c) ANSI C63.10 2009 PASS AC Power Line Conducted Emission 47 CFR Part 15, Subpart C Section 15.207 ANSI C63.10 2009 PASS Conducted Peak Output Power 47 CFR Part 15, Subpart C Section 15.247 (b)(3) KDB558074 D01 PASS 6dB Occupied Bandwidth 47 CFR Part 15, Subpart C Section 15.247 (a)(2) KDB558074 D01 PASS Power Spectral Density 47 CFR Part 15, Subpart C Section 15.247 (e) KDB558074 D01 PASS Pseudorandom Frequency Hopping Sequence 47 CFR Part 15, Subpart C Section 15.247(b)(4)&TCB Exclusion List (7 July 2002) ANSI C63.10 (2009) PASS Band-edge for RF Conducted Emissions 47 CFR Part 15, Subpart C Section 15.247(d) KDB558074 D01 PASS RF Conducted Spurious Emissions 47 CFR Part 15, Subpart C Section 15.247(d) KDB558074 D01 PASS Radiated Spurious Emissions 47 CFR Part 15, Subpart C Section 15.205/15.209 ANSI C63.10 2009 PASS Band Edge (Radiated Emission) 47 CFR Part 15, Subpart C Section 15.205/15.209 ANSI C63.10 2009 PASS Remark: Model No.: Asound-66, 840042, 840043, 840044, 840045, 840046 Only the model Asound-66 was tested, since the electrical circuit design, layout, components used and internal wiring were identical for all above models. Only different on model number and color. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM130200078403 Page: 3 of 47 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documen…

Text truncated - open the document above for the full version.

1 Photographs- EUT Test Setup (Test Model No.: Asound-66) 1.1 Conducted Emission 1.2 Radiated Emission 1.3 Radiated Spurious Emission