A7MBTS100Hex-Btspeaker

Bluetooth speaker Manual: ( double print) 4. Application 5. Troubleshooting Applicable to all Bluetooth devices. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. 1 2 3 4 5 6 User Manual Hands-free call is only available when Bluetooth is connected. The phone call can be interfered with by high frequency electromagnetism, users should avoid if possible. Bluetooth is a bidirectional transmitting protocol; transmitting distance is highly related to audio player. Compatible Bluetooth players are recommended. Some terminal players are without automatically switching play function. In this case, POP noise will exist in the interval of every 2 songs. 6. Accessories: USB charging cable, Audio cable,2 pieces; User manual, 1 piece. When Bluetooth transmitting devices cannot be connected, a possible solution is to delete the Bluetooth device name from the list, turn off Bluetooth on the device, turn back on, re-discover the device, and pair again. The sound performance could also be affected when BT transmitting devices is under poor signal environment, or under low battery capacity. General Micro USB port Laser printing top button, Classic blue light Air ducting hole Anti-skid Silicon Pad Wireless Bluetooth transmission for mobile phone, laptop, ipad, etc Activate Computer’s Bluetooth (if the computer does not have built-in Bluetooth, plug in a Bluetooth adapter) – Turn speaker to pairing mode (Blue light flashing quickly) – Search Bluetooth speaker –Paring – Connect and Play Connect your computer and the HEX speaker via 3.5mm audio cable 2. Structure 1. Micro USB: Charging port; 2. 3.5mm Audio port; 3. Power switch: Switch on/off; 4. Mic: Serve as microphone during hands-free call; 5. Answer / hang up the phone call under Bluetooth mode; 6. LED Indicator: Built-in battery indicator,Red light on - In charging. 3. Usage Important – Verify that the speaker is turned on and charged. Play via Computer: Product Name: HEX Product Type: Bluetooth Speaker Size & Weight:74*74*65mm;176.8g Material100% ROHS PC & ABS S/N & Distortion Ratio:≥85db;≤0.5% Frequency Response:100HZ-- 20KHZ Output Power: RMS 3.0 watt Battery:3.7V/500MA Speaker Spec.:40mm 3W/2.8Ω Advanced Bluetooth 3.0 (up to 10 meters range) Built-in Li-polymer battery with 500mah Up to 4-6 hours playing time 1. Description Play via Mobile phone: Activate Mobile phone’s Bluetooth – Search BT speaker – Find HX-BTS100 –Paring – Connect and Play Connect your mobile phone and the HEX speaker via 3.5mm audio cable size:250x50mm This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, (2) this device must accept any interference received, including interference that may cause undesired operation. RoHS Made in China CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm

Shenzhen Reflying Electronic Co., Ltd Authority to Act as Agent Date: _____2014-7-1___ To Whom It May Concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Vicky Yuan in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all matters relating to all processes required in FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: ___12 months_____ By: ________________________ (Signature 1 ) (Print name) Title: _____MANAGER____________________ On behalf of: ____ Shenzhen Reflying Electronic Co., Ltd __________________ (Company Name) Telephone: ________+86 755 26718925_______________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Shenzhen Reflyin g Electronic Co.,Ltd Request for Confidentiality Date: _ 2014-07-01 Subject: Confid en tiality Req ues t for: ____FCC ID: A7MBTS100___ Pursuant to FCC 47 CRF 0.457(d) an d 0. 459 an d IC RSP-100, Section 10, th e applicant reques ts th at a part of the su bject FCC application be held confidenti al. Type of Confidential ity Requested Exhibit Shor t Term Permanent Block Diagr ams Short Term External Photos Shor t Term Permanent* 1 Internal Photos Shor t Term Permanent Operation Description/Theory of Operation Shor t Term Permane nt Parts List & Placement/BOM Shor t Term Permanent Tune-Up Proc ed ure Shor t Term Permanent Schematics Shor t Term Test Setup Phot os Shor t Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary) ______ _ Shenzhen Reflying Elec tronic Co.,Ltd____ has spent sub stantial effort in developing this product and it is one of the first of its kind in industry. Having th e subject information ea sily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confident ial be permanently withheld from public review due to materials th at contain trade secrets and propriet ary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidentia l be withheld from public view for a period of ___(specify number of days not to exceed 180 ) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marke ting or release of the product to the public. Applicant is also aware that they are responsible to noti fy ACB in th e event information regarding the pr od uct or the pr oduct is made available to the public. ACB will then release the documents listed above fo r public disclosure pursuant to FCC Public Noti ce DA 04-170 5. NOTE for Industry Canada Applications: The ap plicant un derstands that until such time that IC distinguishes between Short Term an d Permanent Confidentiality, eit her type of marked exhibit above will simply be marked Confide ntial when submitted to IC. Sincerely, By: __ ___________________ (Signature/Title 3 ) (Print na me) 1 - The asterisked ite ms (*) req uire fu rther justificatio n be fore per manent co nf id entiality will be allowed. Thes e also currently require review by the FCC under th eir Permit-But- Ask po licy before the grant is issued and can delay co mplet ion of an ap plicat ion. Further justification should be added to the no te ab ove. One such example for a potted device woul d be: “The EUT is FULLY potted using a non-remova ble ep oxy based material. Remova l of potting material ca uses irr eparable damag e to inte rnal circu itry. See photographs exhibits that outli ne the device be fore and af ter pott ing.” 2 - Pleas e refer to ht tp:/ /acbcert.com/documents/misc-docs/Memo-Short-Ter m-Vs-Standard-Confident ia lit y.p df for co mplete details. 3 - Must be signed by applicant contact giv en for applicant on the FCC sit e, or by the author ized ag ent if an ap prop riate au thorized agent letter has been provided. Letter s should be placed on ap propriate letter he ad.

Shenzhen Reflying Electronic Co.,Ltd Model Confirmation Letter We, Shenzhen Reflying Electronic Co.,Ltdcertify th e product: Hex-Btspeaker, And item No.: HX-BTS100, RFSND33 Their electrical circuit design, layout, component s used and internal wiring ar e identical, Only the Item number and color are dif ferent. Agency Agreement Expiration Date: __ 12 months_____ By: _____ ___________________ Wen, Luo_______________ (Signature 1 ) (Print name) Title: ____________manager______________ On behalf of: Shenzhen Reflying Electr onic Co.,Ltd Telephone: _______0755－26718925___________________

1 Photographs - EUT Constructional Details Test model No.: HX-BTS100

1 Photographs - EUT Constructional Details Test model No.: HX-BTS100

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM140700357903 Page: 1 of 7 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page RF Exposure Evaluation Report Application No.: SZEM1407003579RF Applicant: Shenzhen Reflying Electronic Co., Ltd Manufacturer: Shenzhen Reflying Electronic Co., Ltd Factory Shenzhen Reflying Electronic Co., Ltd Product Name: Hex-Btspeaker Model No.(EUT): HX-BTS100 Add Model No.: RFSND33 FCC ID: A7MBTS100 Standards: 47 CFR Part 1.1307(2013) 47 CFR Part 1.1310(2013) Date of Receipt: 2014-07-10 Date of Test: 2014-07-14 to 2014-07-21 Date of Issue: 2014-07-29 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM140700357903 Page: 2 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2014-07-29 Original Authorized for issue by: Tested By 2014-07-21 (Owen Zhou) /Project Engineer Date Prepared By 2014-07-29 (Molinda Li) /Clerk Date Checked By 2014-07-30 (Emen Li) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM140700357903 Page: 3 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Contents Page 1 COVER PAGE ......................................................................…

Text truncated - open the document above for the full version.

1 2 3 4 56 ABCD 6 5 4 3 2 1 D CBA Title Number Revision Size B Date: 27-Jun-2014 Sheet of File: E:\ 开发案 \ 三角 \6-4 客人确认后修改版本 \CQSJ-V00 2.dd b Drawn By: PIO21 1 PIO18 2 PIO17 3 PIO9 4 PIO7 5 PIO6 6 SPI-PCM 7 PI04/CS 8 PI03/MISO 9 PI02/MOSI 10 PI01/CLK 11 RST 12 VBAT 13 GND 14 VCHG 15 CHG-EXT 16 VBAT-SENSE 17 PIO01/TX 18 PIO00/RX 19 USB-N 20 USB-P 21 POWER-EN 22 1V8 23 LED0 24 LED1 25 LED2 26 LINE/MIC-AN 27 LINE/MIC-AP 28 MIC-BIAS 29 LINE-BN 30 LINE-BP 31 NC1 32 NC 33 SPK-LN 34 SPK-LP 35 RF-GND 36 RF 37 RF-GND1 38 U1 F-3288(8615) BAT R110K 12 34 k1 R210K K2 SW-SPDT LED1 R31K BAT 1 C1 NC CTRL 1 BYPASS 2 IN- 3 IN+ 4 OUT+ 5 VDD 6 GND 7 OUT- 8 U2 HT6873 PVCC PVCC R412KR512K C3333C4333 IN-P IN-N IN-N IN-P C5106 12 J1 C6104 C7106 C8106 C27104 GND 3 4 R 1 L 2 P1 PHONE JACK4 PVCC OUT1 1 IN1- 2 IN1+ 3 VEE 4 VCC 8 OUT2 7 IN2- 6 IN2+ 5 U3 JRC4558 R6100K R7100K VREF R810K R910KR1010K C9105C10105 R11 1K R12 1K R13 1K R14 1K IN-BP LINE-BP LINE-BN C11475 C12683 LINE-BN R151K R1630K C14NC AUX-BT R1710k VREF VCC 1 D- 2 D+ 3 ID 4 GND 5 GND 6 GND 7 GND 8 GND 9 J3 MICRO 5PIN D11206 S4 CHG 1 GND 2 BAT 3 PROG 5 VCC 4 U4LP4054 BAT R182K C15105 C16105 LED2 R191k 5V 5V R21 4.7K R2210k PVCC C17100nC18100n R232k2 L115NH C1915P 12 J2 CON2 MIC-BIAS MIC-BIAS R2410K R25NC MUTE R26NC R27NC R3010kR3110k R3230k C20683 C21105C22105 LINE-BP C23NC R33 1K IN-BP C24103 AUX-BT MUTE 12 J4 CON2 R1000 LED4 MIC-AN MIC-AN

SGS-CSTC Standards Technical Services Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM140700357901 Page: 1 of 89 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No: SZEM1407003579RF Applicant: Shenzhen Reflying Electronic Co., Ltd Manufacturer: Shenzhen Reflying Electronic Co., Ltd Factory: Shenzhen Reflying Electronic Co., Ltd Product Name: Hex-Btspeaker Model No.(EUT): HX-BTS100 Add Model No.: RFSND33 FCC ID: A7MBTS100 Standards: 47 CFR Part 15, Subpart C (2013) Date of Receipt: 2014-07-10 Date of Test: 2014-07-14 to 2014-07-21 Date of Issue: 2014-07-29 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM140700357901 Page: 2 of 89 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2014-07-29 Original Authorized for issue by: Tested By 2014-07-21 (Owen Zhou) /Project Engineer Date Prepared By 2014-07-29 (Molinda Li) /Clerk Date Checked By 2014-07-30 (Emen Li) /Reviewer Date SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM140700357901 Page: 3 of 89 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203/15.247 (c) ANSI C63.10 (2…

Text truncated - open the document above for the full version.

1 Photographs - EUT Test Setup Test model No.: HX-BTS100 1.1 Conducted Emission 1.2 Radiated Emission 1.3 Radiated Spurious Emission