AB6NT2100V3231AWS Radio

5050 40th Street NE Calgary, Alberta Canada (T3J 4P8) Request for Confidentiality March 19, 2008 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: Request for confidentiality letter FCC Tx ID: AB6NT2100V3231 IC: 332D-2G1V3231 DearSir/Madam Please note that the request for confidentiality letter dated February 22nd, 2008 and uploaded with the above application is asking for confidential treatement, among other exhibits, of the Exhibit 3 which is refered as the Technical Description document and was uploaded by error as the block diagram type. At a later time the real Block Diagram document was uploaded in the application folder as the block diagram type. Please destroy the Technical Description document, not needed for this application. Our request for confidentiality applies to the following sections: Exhibit 3: Block Diagram Exhibit 6: Internal Photos Exhibit 8A/B: Circuit Schematics Exhibit 9A/B: Parts Lists Exhibit 9C: Tune Up procedure Exhibit 11: User’s Manual Exhibit 12: Operational Description The application contains technical information that Nortel Networks deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter Marin Sampaleanu, P. Eng. Title: Regulatory Prime Email: [email protected] Telephone: (403) 769 2738 Fax: (403) 769 7680

5050 40th Street NE Calgary, Alberta Canada (T3J 4P8) Original Equipment Application March 18, 2008 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: Original Equipment Certification FCC Tx ID: AB6NT2100V3231 IC: 332D-2G1V3231 DearSir/Madam Following are our responses to ATCB comments of March 12-13., 2008. Each item number below adresses the respective ATCB comment. 1. Internal Photos. Exhibit 6 shows both sides of each board of in the RF path of the AB6NT2100V3231 device and also the internal construction of the radio. For file size reasons this exhibit was split into several sub-exhibits (6A – 6E).Each exhibit has been up-issued to Rev 1. 2. A drawing was added to Exhibit 4 to show the placement of the label on the device. The Exhibit 4 was up-issued as Exh 4 Rev 1. 3. A corrected form with the correct Equipment code (TNB) was uploaded in the application folder as ATCB Form 731 Rev 1. 4. This comment was generated by a misunderstanding. The word “indoor” from the Operational Description Document refers to “indoor installation” of the base station only, as compared with “outdoor installation” and NOT to “indoor operation”. There is no intent to install an indoor antenna to operate with this device. 5. Factory Tune-up: The paragraph 4.9 of the Exhibit 2 Test Report Summary describes the factory tune-up procedure. 6. The output power 79W: The Operational Document (Exh 12) statement regarding the output power is that the AWS MFRM 3, which is a device similar to AWS 3231 meets the requirement for nominal Tx output power of 18 W per carrier and 54 W per sector. Both AWS MFRM 3 and AWS 3231 have three antenna ports, one for each sector, so what is specified and tested is the sector output power. Both these radios have the sector power pooling feature which allows to increase the transmitted power of a sector in a multi-sector base station while lowering the power of the rest of the sectors. For the AB6NT2100V3231, the specified power is the maximum power including the sector power pooling which is the maximum power that is measured at the antenna port and is higher than the nominal Tx output power which does not include the sector power pooling. 7. Type Acceptance: The wording “type acceptance” was replaced by the word “certification” in the document Test Report Summary from Exhibit 2 which was up-issued as Exhibit 2 Rev 1. 8. The plots that were pointed out in the comments are plots of "Channel Power" measurement. Those channel power measurements were made for each carrier configuration close to the upper and lower edge of the AWS band, namely, 2108 to 2109 MHz and 2156 to 2157 MHz. Although those frequencies were captured in the "9 kHz - lower adjacent 1 MHz" and "upper adjacent 1 MHz to 5 GHz" plots, which have a RBW of 1 MHz as per the FCC requirement, we wanted to provide additional information about the worst section in the plots. That's why we decided to make "Channel Power" measurements for 2108 to 2109 and 2156 to 2157 MHz, with the channel bandwidth being set to 1 MHz and we chose a RBW of 5 kHz (since this is an extra plot that provides additional information and is not specified by the FCC). As can be seen in the labels for these plots, the word "verification" is inserted at the end of the label to signify that this plot is for verification purposes. To avoid any confusion all plots marked as “verification” and introduced as additional information have been removed from the test report and the report was up-issued as the Exh 2A Rev 1. Please contact the undersigned for further information if necessary. Thank you for your attention to these matters. Important: Please see attached request for confidentiality Marin Sampaleanu, P. Eng. Title: Regulatory Prime Email: [email protected] Telephone: (403) 769 2738 Fax: (403) 769 7680

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 March 12-13, 2008 RE: Nortel Networks FCC ID: AB6NT2100V3231 After a review of the submitted information, I have a few comments on the above referenced Application. Depending on your responses, kindly understand there may be additional comments. 1) For internal photos, generally the photographs should include the front/back of each board in the RF path and also the general internal construction of the device. A few additional photographs will still likely be necessary. Please review. 2) Labeling exhibit should also show placement of the label (i.e. “location”) on the device. 3) Equipment code on Part III (4)(a) should be TNB. Please adjust. It appears the grantee code was inserted here. 4) While we understand that RF exposure may be handled by licensing for fixed outdoor use, there are some concerns for indoor given indoor suggestions in the operational description (see page 14). If so, Pico-base stations, Micro-base stations and other fixed-mounted transmitters operating with indoor antenna(s) typically are required to satisfy MPE Categorical Exclusion Limits established in §2.1091. This would require RF exposure evaluation (i.e. measurements – not just calculations) are required by 2.1091 for > 1.5 GHz range if the ERP is > 3.0 Watts. Please review/explain, and provide any necessary information. 5) Factory Tune up procedure does not appear to be provided. Please provide. ? (2.1033(c)(9)) 6) Most documentation mentions 79 Watts output (1 or multiple carriers). However operational description mentions 18 Watts. Please explain. 7) FYI....Some of the test report documents mention type acceptance. Please note that this is an old authorization by which licensed devices used to be approved. However, this is no longer true and is referred to simply as Certification. 8) Several spurious emissions plots do not appear to match the labels and also appear to use RBW < specified in the tables. Many appear to be bandedge measurements, but are labeled for much wider spans and use RBW < 1%. Please review/explain as necessary. Timothy R. Johnson Examining Engineer mailto: [email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

5050 40th Street NE Calgary, Alberta Canada (T3J 4P8) EXHIBIT 5 EXTERNAL PHOTOS Applicant: Nortel Networks For original Equipment Application on: FCC: AB6NT2100V3231 IC: 332D-2G1V3231

5050 40th Street NE Calgary, Alberta Canada (T3J 4P8) EXHIBIT 4 TRANSMIT LABEL INFORMATION Applicant: Nortel Networks For Original Equipment Application on: FCC: AB6NT2100V3231 IC: 332D-2G1V3231 REVISION DESIGN AUTHORITYTITLEDRAWING NUMBER SCALE SIZE SHEET B 1 OF NORTEL PROPRIETARY INFORMATION: THE INFORMATION CONTAINED IN THIS DOCUMENT IS THE PROPERTY OF NORTEL NETWORKS LIMITED, EXCEPT AS SPECIFICALLY AUTHORIZED IN WRITING BY NORTEL NETWORKS LTD. THE HOLDER OF THIS DOCUMENT SHALL(1) KEEP ALL INFORMATION HEREIN CONFIDENTIAL AND SHALL PROTECT SAME IN WHOLE OR IN PART FROM DISCLOSURE ANDDISSEMINATION TO ALL THIRD PARTIES AND (2) USE SAME FOR OPERATING AND MAINTENANCE PURPOSES ONLY. (CorelDRAW9 05/08/18) PRINTED IN CANADA FULL DATE: DEC. 6, 2007 C N0156686 2 BTS 3231 RADIO MODULE 1.7/2.1GHz ID LABEL SCALE 1.00 CDMA 3231 BTS RADIO MODULE 1.7/2.1 GHzModel No. NTDV51AAE5FCC ID: AB6NT2100V3231IC: 332D-2G1V3231 BACKGROUND COLOURBTS LIGHT GRAY PER S-33470(PANTONE NO. COOL GRAY 5C) NORTEL LOGOWHITE PERS-33294 TEXT:ARIAL NARROW BOLDBLACK PER S-33154 BACKGROUND COLOUROXFORD GRAY PER S-33477(PANTONE NO. COOL GRAY 11C) -REDESIGN TO HAVE A COMBINED ID / REGULATORY LABEL NOTES:1. UNLESS OTHERWISE SPECIFIED, ALL DIMENSIONS ARE EXPRESSED IN INCHES. TOLERANCES SHALL BE;TWO DECIMAL PLACES = +/- .01THREE DECIMAL PLACES = +/- .005 ALL LABEL CORNERS SHALL HAVE A .10 RADIUS. 2. THIS DESIGN FILE WAS CREATED IN ACCORDANCE WITH STD. 1517.20. THE LABELS /ARTWORK SHALL MEET ALL THE REQUIREMENTS OF NPS-90942. 3. THE ARTWORK (SEE SHEET 2) SHALL BE PLOTTED AT A MINIMUM OF 1200 DPI. THE FONT(S) SHALL BE: NORTEL INTERSTATE REGULAR 4. MATERIAL: .010 POLYCARBONATE PER R0115902 FINISH: VELVET/MATTE ADHESIVE: .002 PRESS SENSITIVE WITH PEEL-OFF LINER PER R0117260 5. NORTEL NETWORKS OBSERVATIONAL STANDARDS FOR COLORING (CORP. STD. 2701.01); BACKGROUND: OXFORD GRAY PER S-33477 (PANTONE NO. COOL GRAY 11C) TEXT & GRAPHICS: WHITE PER STANDARD S-33294 6. ALL MATERIALS AND FINISHES SHALL BE COMPLIANT TO NORTEL NPS 00200. 2.45" 0.98" 0.42" N0156686-M1 REVISION C : SCALE= 1/1 SHEET 2 OF 2 CDMA 3231 BTS RADIO MODULE 1.7/2.1 GHzModel No. NTDV51AAE5FCC ID: AB6NT2100V3231IC: 332D-2G1V3231 N0156686 BTS 3231 RM Regulatory Label Placed on front of module, top left corner, to the left of the module handle

5050 40th Street NE Calgary, Alberta Canada (T3J 4P8) EXHIBIT 10 RF EXPOSURE GUIDELINES Applicant: Nortel Networks For Original Equipment Application on: FCC: AB6NT2100V3231 IC: 332D-2G1V3231 RF Exposure Guidelines for Cellular, PCS and LMDS Antenna Sites Document no: SI-EMR-R01.5 Authors: Product Integrity BWA – RF Engineering Microwave Radio Design Proprietary Northern Telecom Antenna Siting Guideline 3 The information disclosed herein is proprietary to Nortel Networks or others and is not to be used by or disclosed to unauthorized persons without the written consent of Nortel. The recipient of this document shall respect the security status of the information. 1.0 Executive Summary This document serves as a guideline for the deployment and installation of Nortel Networks’ wireless base station equipment with respect to the control of electromagnetic radiation (EMR) exposure. The objective is to provide guidance on where antennas can be deployed, how to calculate power densities and safe distances and how to protect users from excessive exposure to electromagnetic radiation. This guideline is in response to recent regulatory requirements originating in the US aimed at controlling human exposure to EMR. Safe distance formulae for base stations: Limits Application Uncontrolled r [ meters ] Controlled r [ meters ] Cellular r0. 300 ER P= r0. 135 ER P= PCS r0. 228 ER P= r= 0.102 ERP DCS r0. 228 ER P= r=0.102ERP LMDS r = 1 r = 0.4 P-to-P Microwave Radio r = 1 r = 0.4 Uncontrolled refers to situations where individuals are either unaware or not in control of their exposure to the electromagnetic fields in question. This typically pertains to the general public. Controlled refers to situations where individuals are both aware of and in control of their exposure to the electromagnetic fields in question. This typically pertains to trained staff that is in contact with these fields as a result of their employment and have authority to limit their exposure. Note: This document includes DCS in its examples. If the EU adopts ENV50166, or any other EMR standard, then that document will replace this as the guideline for DCS products. Until that happens, these limits can be used to ensure due diligence on Nortel Networks’ behalf. Northern Telecom Antenna Siting Guideline iv Table of Contents 1.0 Executive Summary ................................................................................. ii 2.0 Introduction ............................................................................................. 1 3.0 Guideline ............................................................................................. 2 3.1 MPE Limits ............................................................................................. 3 3.2 Safe Distance and Power Density Calculations ................................. 5 3.2.1 Minimum Safe Distance ............................................................ 6 3.2.2 Power Density Calculation ........................................................ 8 3.3 Site Planning ............................................................................................ 9 4.0 Other Components ................................................................................. 10 5.0 Assumptions ........................................................................................... 11 6.0 References .............................................................................................. 12 7.0 Acronyms ............................................................................................... 12 Northern Telecom Antenna Siting Guideline 1 2.0 Introduction Regulatory bodies in the US, Federal Communications Commission (FCC), and Canada, Health Canada, are imposing Maximum Permissible Exposure (MPE) limits. FCC’s OET Bulletin #65 (versions in progress) addresses calculation and measurement procedures to determine compliance with the FCC limits which includes the 800 MHz cellular and 1.9 GHz PCS bands. The equipment and its associated deployment must comply with FCC Guidelines, ET Docket No. 93-62, Released August 1, 1996, (FCC 96-326). This standard is largely based on the limits and test methods outlined in IEEE C95.1-1982, NCRP Report No. 86 and C95.3-1982 respectively. The applicable portions of both are summarized in this document to assist in the antenna site planning to ensure compliance. The exposure limits are currently in effect. The requirement for installers to evaluate the exposure at an installation takes effect on Sept. 1/97. The exposure limits should apply now to all known sites since existing facilities are not exempt or grand fathered from the new rules. The FCC has determined that certain sites will require “Environmental Evaluations” in order to show compliance to the standards. Adhering to these guidelines can ensure compliance to the standard, and therefore can be the basis for the Environmental Evaluation. Please note that some installations do not require such routine evaluation: exceptions are noted further in this document. Adherence to these guidelines is recommended to promote safety. An installation of equipment that is identified as exempt may require an Environmental Evaluation if the combined energy of other Radio Systems at the site and the new installation could reasonably exceed the safety limits. Environmental Evaluations are kept on hand, as opposed to file with the FCC, unless requested by the FCC for substantiation. Where Nortel Networks is responsible for installing or engineering base stations, the person in charge should be aware of and have access to documentation for making an Environmental Evaluation. Also, Nortel Networks will need to maintain documentation for assurances to the FCC that Environmental Evaluations have been conducted for each radio station that uses our Experimental Radio License, or STA, where the station transmits at 100 Watt ERP or more. Northern Telecom Antenna Siting Guideline 2 3.0 Guideline The object…

Text truncated - open the document above for the full version.

5050 40th Street NE Calgary, Alberta Canada (T3J 4P8) EXHIBIT 2B TEST REPORT NTS 1 Applicant: Nortel Networks For original Equipment Application on: FCC: AB6NT2100V3231 IC: 332D-2G1V3231 Product Integrity Laboratory 5151-47 th Street, NE Calgary, Alberta T3J 3R2 Tel: (403) 568-6605 Fax : (403) 568-6970 FCC Part 27 Radiated Emission Test Report Project Code CG-778 (Report CG-778-EM-1-1) NORTEL Networks Wireless AWS 3231 Revision: 1 (Supersedes report CG-778-EM-1-0) February 15, 2008 Prepared for: Nortel Networks Wireless Author: Deniz Demirci EMC Specialist Approved by: Nick Kobrosly Director of Operations Confidentiality Statement: This report and the information contained herein represent the results of testing articles/products identified and selected by the client. The tests were performed to specifications and/or procedures approved by the client. National Technical Systems (“NTS”) makes no representations expressed or implied that such testing fully demonstrates efficiency, performance, reliability, or any other characteristic of the articles being tested, or similar products. This report should not be relied upon as an endorsement or certification by NTS of the equipment tested, nor does it represent any statement whatsoever as to its merchantability or fitness of the test article or similar products for a particular purpose. This document shall not be reproduced except in full without written approval from National Technical Systems (“NTS”) and the customer. CG-778-EM-1-1 Emissions Test Report Nortel Networks Wireless AWS 3231 The test results contained in this report refer exclusively to the product(s) presented for testing. The test results do not cover models or products not referred herein. This test report should not be published or duplicated in whole or part without permission from the testing body and the customer. NTS Product Integrity Laboratory, 5151-47 th Street N.E. Tel: 403-568-6605, Fax: 403-568-6970 Confidential Page 2 of 30 February 15, 2008 Report Summary Test Facility: National Technical Systems, Canada Product Integrity Laboratory 5151-47 th Street, N.E. Calgary Alberta T3J 3R2 Accreditation Numbers: FCC 101386 IC 46405-3978 - File # IC3978-2 Accredited by Standards Council of Canada Accredited Laboratory No. 440(Conforms with requirements of CAN−P−4D (ISO/IEC 17025)) CLIENTS SERVED: All interested parties FIELDS OF TESTING: Electrical/Electronic, Mechanical/Physical ISSUED ON: 2005−06−02 VALID TO: 2009−03−20 Nortel Network Wireless Performed For: 5050-40th Street, N.E. Calgary Alberta T3J 4P8 Customer Representative: Name: Daryl Therens Phone #: 403-769-4103 Email Address: [email protected] Responsible Manager: Name: Rick Kerslake Phone #: 403-769-5090 Email Address: [email protected] CG-778-EM-1-1 Emissions Test Report Nortel Networks Wireless AWS 3231 The test results contained in this report refer exclusively to the product(s) presented for testing. The test results do not cover models or products not referred herein. This test report should not be published or duplicated in whole or part without permission from the testing body and the customer. NTS Product Integrity Laboratory, 5151-47 th Street N.E. Tel: 403-568-6605, Fax: 403-568-6970 Confidential Page 3 of 30 February 15, 2008 Test Summary Deviations* from: Status Applicable Rule Parts Appendix Test/Requirement Description Base Standard Test Basis NTS Procedure A TX Radiated Spurious Emissions 30 MHz- 2 2 GHz No No No PASS FCC CFR 47 Part 27 B Test Equipment List No No No NA NA Test Result: The product presented for testing complied with test requirements as shown above. Test Log Appendix Test Case Start End Tester A Radiated Emissions 30 MHz – 22 GHz FCC CFR 47 Part 27 Jan 31, 2008 Feb 04, 2008 Lixin Wang Deniz Demirci James Mackay The test outlined may not be inclusive of all testing required by the Base Standards or fulfill the applicable regulatory requirements in their entirety. Test Result: The product presented for testing complied with test requirements as shown above. Prepared By: ______________________ Deniz Demirci EMC Specialist Reviewed By: ______________________ Alex Mathews Compliance Specialist Checked By: ______________________ Robyn Zuehlke Quality Representative CG-778-EM-1-1 Emissions Test Report Nortel Networks Wireless AWS 3231 The test results contained in this report refer exclusively to the product(s) presented for testing. The test results do not cover models or products not referred herein. This test report should not be published or duplicated in whole or part without permission from the testing body and the customer. NTS Product Integrity Laboratory, 5151-47 th Street N.E. Tel: 403-568-6605, Fax: 403-568-6970 Confidential Page 4 of 30 February 15, 2008 Table of Contents REPORT SUMMARY..................................................................................................................................................2 TEST SUMMARY........................................................................................................................................................3 TEST LOG....................................................................................................................................................................3 REGISTER OF REVISIONS........................................................................................................................................5 1.0 INTRODUCTION.............................................................................................................................................6 1.1 PURPOSE.........................................................................................................................................................6 1.2 ABBREVIATIONS AND DEFINITIONS......................................................................................................................6 1.3 REFERENCES......................................................................…

Text truncated - open the document above for the full version.

5050 40th Street NE Calgary, Alberta Canada (T3J 4P8) EXHIBIT 2C TEST REPORT NTS 2 Applicant: Nortel Networks For original Equipment Application on: FCC: AB6NT2100V3231 IC: 332D-2G1V3231 Product Integrity Laboratory 5151-47 th Street, NE Calgary, Alberta T3J 3R2 Tel: (403) 568-6605 Fax : (403) 568-6970 FCC Part 27 Radiated Emission Test Report Project Code CG-778 (Report CG-778-EM-2-1) NORTEL Networks Wireless AWS 3231 With DOM-A Revision: 1 (Supersedes report CG-778-EM-2-0) February 26, 2008 Prepared for: Nortel Networks Wireless Author: Deniz Demirci EMC Specialist Approved by: Nick Kobrosly Director of Operations Confidentiality Statement: This report and the information contained herein represent the results of testing articles/products identified and selected by the client. The tests were performed to specifications and/or procedures approved by the client. National Technical Systems (“NTS”) makes no representations expressed or implied that such testing fully demonstrates efficiency, performance, reliability, or any other characteristic of the articles being tested, or similar products. This report should not be relied upon as an endorsement or certification by NTS of the equipment tested, nor does it represent any statement whatsoever as to its merchantability or fitness of the test article or similar products for a particular purpose. This document shall not be reproduced except in full without written approval from National Technical Systems (“NTS”) and the customer. CG-778-EM-2-1 Emissions Test Report Nortel Networks Wireless AWS 3231 with DOM-A The test results contained in this report refer exclusively to the product(s) presented for testing. The test results do not cover models or products not referred herein. This test report should not be published or duplicated in whole or part without permission from the testing body and the customer. NTS Product Integrity Laboratory, 5151-47 th Street N.E. Tel: 403-568-6605, Fax: 403-568-6970 Confidential Page 2 of 31 February 26, 2008 Report Summary Test Facility: National Technical Systems, Canada Product Integrity Laboratory 5151-47 th Street, N.E. Calgary Alberta T3J 3R2 Accreditation Numbers: FCC 101386 IC 46405-3978 - File # IC3978-2 Accredited by Standards Council of Canada Accredited Laboratory No. 440(Conforms with requirements of CAN−P−4D (ISO/IEC 17025)) CLIENTS SERVED: All interested parties FIELDS OF TESTING: Electrical/Electronic, Mechanical/Physical ISSUED ON: 2005−06−02 VALID TO: 2009−03−20 Nortel Network Wireless Performed For: 5050-40th Street, N.E. Calgary Alberta T3J 4P8 Customer Representative: Name: Daryl Therens Phone #: 403-769-4103 Email Address: [email protected] Responsible Manager: Name: Rick Kerslake Phone #: 403-769-5090 Email Address: [email protected] CG-778-EM-2-1 Emissions Test Report Nortel Networks Wireless AWS 3231 with DOM-A The test results contained in this report refer exclusively to the product(s) presented for testing. The test results do not cover models or products not referred herein. This test report should not be published or duplicated in whole or part without permission from the testing body and the customer. NTS Product Integrity Laboratory, 5151-47 th Street N.E. Tel: 403-568-6605, Fax: 403-568-6970 Confidential Page 3 of 31 February 26, 2008 Test Summary Deviations* from: Status Applicable Rule Parts Appendix Test/Requirement Description Base Standard Test Basis NTS Procedure A TX Radiated Spurious Emissions 30 MHz- 22 GHz No No No PASS FCC CFR 47 Part 27 Test Result: The product presented for testing complied with test requirements as shown above. Test Log Appendix Test Case Start End Tester A Radiated Emissions 30 MHz – 22 GHz FCC CFR 47 Part 27 Feb 19, 2008 Feb 20, 2008 Lixin Wang The test outlined may not be inclusive of all testing required by the Base Standards or fulfill the applicable regulatory requirements in their entirety. Test Result: The product presented for testing complied with test requirements as shown above. Prepared By: ______________________ Deniz Demirci EMC Specialist Reviewed By: ______________________ Alex Mathews Compliance Specialist Checked By: ______________________ Robyn Zuehlke Quality Representative CG-778-EM-2-1 Emissions Test Report Nortel Networks Wireless AWS 3231 with DOM-A The test results contained in this report refer exclusively to the product(s) presented for testing. The test results do not cover models or products not referred herein. This test report should not be published or duplicated in whole or part without permission from the testing body and the customer. NTS Product Integrity Laboratory, 5151-47 th Street N.E. Tel: 403-568-6605, Fax: 403-568-6970 Confidential Page 4 of 31 February 26, 2008 Table of Contents REPORT SUMMARY..................................................................................................................................................2 TEST SUMMARY........................................................................................................................................................3 TEST LOG....................................................................................................................................................................3 REGISTER OF REVISIONS........................................................................................................................................5 1.0 INTRODUCTION.............................................................................................................................................6 1.1 PURPOSE.........................................................................................................................................................6 1.2 ABBREVIATIONS AND DEFINITIONS......................................................................................................................6 1.3 REFERENCES...........................................................................................…

Text truncated - open the document above for the full version.

5050 40th Street NE Calgary, Alberta Canada (T3J 4P8) EXHIBIT 2 TEST REPORT SUMMARY Applicant: Nortel Networks For Original Equipment Application on: FCC: AB6NT2100V3231 IC: 332D-2G1V3231 EL CDMA BTS Development NORT Test Summary for Original Equipment Authorization CC Tx ID: AB6NT2100V3231 T2100V3231 08 e: Marin Sampaleanu rized persons. While copies may be printed, it is not recommended. Viewing of the aster electronically ensures access to the current issue. Any hardcopies must be regarded as ncontrolled copies. ortel Networks Proprietary: he information herein is not to be disclosed without permission of its author. opyright © 2008 Nortel Networks All rights reserved F IC ID: 332D-2G1V3231 Document: TRS AB6N Stream: 00 Issue: 02 Issue date: March 17, 20 Security Status: Proprietary Document Prim DISCLAIMER: The master of this document is stored on an electronic database and is "write protected"; it may be altered only by autho m u N T C AWS V3231 FCC Part 27 Test Summary Page 2 of 14 Document Control All other soft and hard copies are to be considered uncontrolled. It is the responsibility of the reader to ensure that the latest approved release of this document is being used. Issue: 00.02 Author: Marin Sampaleanu Nortel Proprietary March 17, 2008 AWS…

Text truncated - open the document above for the full version.