ABZ89FT5901Non Broadcast Transmitter

TO: Federal Communication Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Rd Columbia, MD 21046 May 16, 2024 Pursuant to FCC 22-84 Report and Order and KDB 986446 D01 Covered Equipment v01, the Commission adopted new FCC requirements to protect the nation’s networks and supply chains from equipment that poses an unacceptable risk to national security or the safety of U.S. persons. Specifically, the Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List. Certification designating a U.S. agent for service of process. As required by section 2.911(d)(7), the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. Matt Nawrocki (“the applicant”) acknowledges to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. If the agent changes then the TCB and the FCC must be notified. Matt Nawrocki Motorola Solutions 2000 Progress Parkway, Schaumburg, IL 60196 847-812-5841 [email protected] FCC ID: ABZ89FT5901 FRN: 0034642793 Thank you. Regards, 5/16/2024 Matt Nawrocki Engineering Manager

TO: Federal Communication Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Rd Columbia, MD 21046 May 16, 2024 Pursuant to FCC 22-84 Report and Order and KDB 986446 D01 Covered Equipment v01, the Commission adopted new FCC requirements to protect the nation’s networks and supply chains from equipment that poses an unacceptable risk to national security or the safety of U.S. persons. Specifically, the Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List. Certifications FCC ID: ABZ89FT5901 concerning “covered” equipment. Section 2.911(d)(5)(i)-(ii). Matt Nawrocki (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Matt Nawrocki (“the applicant”) certifies that as of the date of the filing of the application, the applicant is not identified on the covered list as an entity producing covered equipment. Thank you. Regards, 5/16/2024 Matt Nawrocki Engineering Manager Motorola Solutions 2000 Progress Parkway, Schaumburg, IL 60196 847-812-5841 [email protected] FCC ID: ABZ89FT5901 FRN: 0034642793

TO: Federal Communication Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Rd Columbia, MD 21046 ATTENTION: Federal Communication Commission Equipment Authorization To whom it may concern, We would like to submit for Certification to FCC: ABZ89FT5901. Please find in the following application all related documentation to support this New Single Certification. We would appreciate your prompt attention to the submittal. Applicant Company name: Motorola Solutions, Inc. Contact Name: Matt Nawrocki Address: 2000 Progress Parkway, Schaumburg, IL 60196 Telephone No: 847-812-5841 Email: [email protected] FCC ID Number: ABZ89FT5901 05/24/2024 Matt Nawrocki Engineering Manager Motorola Solutions FRN: 0034642793

FCC ID: ABZ89FT5901 ___________________________________________________________________________________________________________ Motorola Solutions Date: May 16, 2024 Rick King Certification Department 1516 Centre Circle Downers Grove, Illinois 60515 Telephone: 630 495-9770 Email: [email protected] ELITE ELECTRONIC ENGINEERING Subject: Extended Frequencies Justification for Certification of Transmitter with FCC ID: ABZ89FT5901 Dear Sir, In accordance with updated requirements pertaining to Publication KDB 634817, Frequency Range Listings for Certification Grants, Motorola Solutions hereby submits attestation that the transmitter described in this submission includes continuous frequencies that are not listed in rule part 90. For the FCC’s Rule Parts 22, 74, 80 and 90 applications, this radio is used in systems by Federal and Public Safety agencies including Police, Fire, and Emergency Medical Services, etc. Please note that Licensed End Users do not have access to any external controls that will allow them to program the equipment. Equipment programming is the responsibility of Authorized Service Personnel. Also, the radio complies with 47 CFR Part 90.203(e) and 80.203(b), in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. It is understood that a grant note code may be added to the grant which indicates this required operation. Sincerely, Matt Nawrocki Engineering Manager FRN: 0034642793 E-mail: [email protected]

FCC ID: ABZ89FT5901 Date: May 16, 2024 Rick King Certification Department 1516 Centre Circle Downers Grove, Illinois 60515 Telephone: 630 495-9770 Email: [email protected] ELITE ELECTRONIC ENGINEERING Subject: Part 90.203 (j) (5) Certification Statement FCC ID: ABZ99FT5101B Dear Sir, Motorola Solutions, Inc certifies that it’s digital base station transmitter FCC ID: ABZ89FT5901, meets a spectrum efficiency standard of one voice channel per 6.25kHz of channel bandwidth. Additionally, Motorola Solutions, Inc certifies the equipment is capable of supporting a minimum data rate of 4800 bits per second per 6.25 kHz of channel bandwidth. . Sincerely, Matt Nawrocki Engineering Manager FRN: 0034642793 E-mail: [email protected]

FCC ID: ABZ89FT5901 HVIN: T8899-800 CONFIDENTIALITY REQUESTED Date: May 5, 2024 Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams (Included in Exhibit B) Short Term External Photos Short Term Permanent Internal Photos Short Term Permanent Operation Description/Theory of Operation (Included in Exhibit B) Short Term Permanent Parts List & Placement/BOM (Included in Exhibit B) Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics (Included in Exhibit B) Short Term Test Setup Photos Short Term Permanent* User’s Manual Motorola Solutions has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Short Term Confidentiality: The applicant requests the exhibits listed above as Short Term confidential be withheld from public review for a duration of 180 days from the date of submission. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By: __________________________ Matt Nawrocki (Signature) (Print name) Title: Engineering Manager

APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FT5901 109AB-T5901 Photographs of the Device EXHIBIT A Photographs – Index EXHIBIT DESCRIPTION A1 ID Label Location A2 FCC / IC Identification Label APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FT5901 109AB-T5901 Photographs of the Device EXHIBIT A1 ID Label Location APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FT5901 109AB-T5901 Photographs of the Device EXHIBIT A2 FCC / IC Identification Label

Mot orola Solut ions Canada, Inc. UPN Number: T5 9 0 1 Company Number: 1 0 9 AB Model Number: T8 8 9 9-8 0 0 Page 1 RF Exposure Technical Brief This Technical Brief calculates the minimum separation distance from an antenna, connected to the subject base station, such that the power density values listed in RSS-102, Radio Frequency (RF) Exposure Compliance of Radiocommunications Apparatus (All Frequency Bands) Table 4.2 and Table 4.4 are not exceeded. The analysis is for a typical installation using a structure mounted antenna. Within the frequency range that the subject equipment operates, 851 MHz – 870 MHz the permitted exposure limit is frequency dependent. Table 1 lists the maximum permitted exposure limits by environment type for the subject equipment at the lowest frequency. The lowest operating frequency, 851 MHz, is selected because the power density calculations per RSS-102, Table 4.2 and Table 4.4 result in a lower exposure level than for the highest operating frequency, 869 MHz. The maximum permitted exposure limit for uncontrolled environments is a power density of 5.67 W/m 2 and the maximum permitted exposure limit for controlled environments is 28.4 W/m 2 . Table 1 - Maximum Permissible Exposure Limits Uncontrolled Environment Controlled Environment Frequency 851-869 MHz 851-869 MHz Limit 5.67 W/m 2 28.4 W/m 2 Example Calculations for DBR M12, 800 MHz Transmitter: The example configuration is a multicarrier site with 12 channels transmitting at 40W, with minimal RF network losses, set to zero for this example, between the transmitter output connector and the antenna input connector. The antenna has an omni directional pattern in the horizontal plane and a 13 degree beamwidth in the vertical plane. The largest dimension of the antenna is in the vertical plane. For the operating band of the equipment commonly available base station antennas have typical gains of 6 dBd or greater. A low gain antenna was selected to realize a higher power density over the analyzed surface area. This configuration results in a conservative separation distance, i.e., larger distance. Table 2 - Transmitter Configuration Frequency 851-869 MHz RF Site Output Power (40Wx12) 480 W RF Network Loss 0 dB Antenna Type RFS BMR6-O-B1 6 dBd / 8.1 dBi (Omni) Antenna length 1.68 m Using Equation 1 the spatially averaged plane-wave equivalent power densities parallel to the antenna in the vertical plane may be estimated by dividing the net input power to the antenna by the surface area of an imaginary cylinder at a distance R from the antenna, with the height of the cylinder equal to the length of the antenna 1 . 1 Federal Communications Commission Office of Engineering & Technology, OET Bulletin 65, “Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields”, Edition 97-01, page 32, Tell’s cylindrical model. Mot orola Solut ions Canada, Inc. UPN Number: T5 9 0 1 Company Number: 1 0 9 AB Model Number: T8 8 9 9-8 0 0 Page 2 Rh Pnet S 2  (1) Where: S = power density, W/m 2 Pnet = net input power to the antenna, W R = radial distance from the antenna, m h = height of the antenna, m The minimum separation distance can be found by solving Equation 1 for R and setting S to the maximum power density for the environment per Table 1. Uncontrolled environment: 02.8 67.568.12 480 2    hS Pnet R m (2) Controlled environment: 60.1 4.2868.12 480 2    hS Pnet R m (3) For the example site configuration the minimum separation distance for an uncontrolled environment is 8.02 m and the minimum separation distance for the controlled environment is 1.60 m.

APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FT5901 109AB-T5901 Report on Test Measurements EXHIBIT E Measurements Report The measurement report shows compliance information against the pertinent technical standards. Each parameter is measured generally at the low end, middle, and at the high end of the applicable frequency band. Each section of the report contains either verbiage or graphs which show compliance to applicable standards as required, explains testing method used, and indicates what the applicable specification is. A list of test equipment for all sections, and certification signoff page are included at the end of the measurement report. SUBMITTED MEASURED DATA -- INDEX EXHIBIT DESCRIPTION E1-1 RF Output-Data E1-2 Occupied Bandwidth, Digital Emissions: Setup, Specifications, and Index E1-2.1, 2, 3 Linear Simulcast Modulation (LSM) E1-2.4, 5, 6 Compatible 4-Level Frequency Modulation (C4FM) E1-2.7, 8, 9 H-DQPSK, P25 Two Slot TDMA Digital Modulation E1-3 Conducted Spurious Emissions: Setup, Specifications, and Index E1-3.1 LSM Conducted Spurious Harmonic Emissions, Power 44 Watts (Average) E1-3.2 LSM Conducted Spurious Harmonic Emissions, Power 2 Watts (Average) E1-3.3 C4FM Conducted Spurious Harmonic Emissions, Power 44 Watts E1-3.4 C4FM Conducted Spurious Harmonic Emissions, Power 2 Watts E1-3.5 H-DQPSK Conducted Spurious Harmonic Emissions, Power 44 Watts E1-3.6 H-DQPSK Conducted Spurious Harmonic Emissions, Power 2 Watts E1-3.7, 8, 9 Conducted Spurious Emission Spectrum, 200 MHz Span, Power Output at 44 Watts, LSM E1-3.10, 11, 12 Conducted Spurious Emission Spectrum, 200 MHz Span, Power Output at 44 Watts, C4FM E1-3.13, 14, 15 Conducted Spurious Emission Spectrum, 200 MHz Span, Power Output at 44 Watts, H- DQPSK E1-4 Radiated Spurious Emissions: Setup, Specifications, and Index E1-4.1 C4FM Radiated Spurious Harmonic Emissions, Power 44 Watts 851MHz E1-4.2 C4FM Radiated Spurious Harmonic Emissions, Power 2 Watts 851MHz E1-4.3 LSM Radiated Spurious Harmonic Emissions, Power 44 Watts 852MHz E1-4.4 LSM Radiated Spurious Harmonic Emissions, Power 2 Watts 852MHz E1-4.5 H-DQPSK Radiated Spurious Harmonic Emissions, Power 44 Watts 853MHz E1-4.6 H-DQPSK Radiated Spurious Harmonic Emissions, Power 2 Watts 853MHz E1-4.7 C4FM Radiated Spurious Harmonic Emissions, Power 44 Watts 860MHz E1-4.8 C4FM Radiated Spurious Harmonic Emissions, Power 2 Watts 860MHz E1-4.9 LSM Radiated Spurious Harmonic Emissions, Power 44 Watts 861MHz APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FT5901 109AB-T5901 Report on Test Measurements EXHIBIT E E1-4.10 LSM Radiated Spurious Harmonic Emissions, Power 2 Watts 861MHz E1-4.11 H-DQPSK Radiated Spurious Harmonic Emissions, Power 44 Watts 862MHz E1-4.12 H-DQPSK Radiated Spurious Harmonic Emissions, Power 2 Watts 862MHz E1-4.13 C4FM Radiated Spurious Harmonic Emissions, Power 44 Watts 868MHz E1-4.14 C4FM Radiated Spurious Harmonic Emissions, Power 2 Watts 868MHz E1-4.15 LSM Radiated Spurious Harmonic Emissions, Power 44 Watts 869MHz E1-4.16 LSM Radiated Spurious Harmonic Emissions, Power 2 Watts 869MHz E1-4.17 H-DQPSK Radiated Spurious Harmonic Emissions, Power 44 Watts 870MHz E1-4.18 H-DQPSK Radiated Spurious Harmonic Emissions, Power 2 Watts 870MHz E1-5 Frequency Stability: Setup, Specifications, and Index E1-5.1 Frequency Stability Vs Temperature E1-5.2 Frequency Stability Vs Voltage E1-6 Test Setup Details E1-7 Statement of Certification APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FT5901 109AB-T5901 Report on Test Measurements EXHIBIT E1-1 RF Power Output Data The RF power output was measured with the indicated voltage applied to the RF Site. The DC current indicated is the total for the site with 1 channel transmitting at the noted power at the top of rack. Max Power requested is 44W, Lower Power is 2W. C4FM Modulation Temperature 25 ̊C Remarks Voltage (V) 48V Frequency (MHz) Low Power (W) Current (A) Max Power (W) Current (A) 851 2.03 36.38 45.20 41.47 860 2.02 37.36 44.53 42.14 870 2.06 37.51 44.31 42.49 LSM Modulation Temperature 25 ̊C Remarks Voltage (V) 48V Frequency (MHz) Low Power (W) Current (A) Max Power (W) Current (A) 851 2.08 37.43 45.71 41.63 860 2.05 37.43 44.55 42.06 870 2.07 37.50 46.34 42.57 H-DQPSK Modulation Temperature 25 ̊C Remarks Voltage (V) 48V Frequency (MHz) Low Power (W) Current (A) Max Power (W) Current (A) 851 2.09 37.40 46.08 42.92 860 2.05 37.46 44.60 42.32 870 2.07 37.53 45.20 42.93 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FT5901 109AB-T5901 Report on Test Measurements EXHIBIT E1-2 (Sheet 1 of 3) Occupied Bandwidth – Linear Simulcast Modulation (LSM), 12.5 kHz Channel Spacing Linear Simulcast Modulation can be used in a system configuration based upon channel usage as described in Exhibit B. The ‘D1E’ emission designator provides usage for telephony, the ‘D1D’ provides usage for data / telecommand, and the ‘D1W’ provides for usage as a combination. All are spectrally identical. The occupied bandwidth charts reference the following setup and specification requirements. Modulation Type: Linear Simulcast Modulation, LSM Emission Designator: 8K70D1E, 8K70D1D, 8K70D1W Channelization: 12.5 kHz Power Setting: 44 Watts, Average Specification Requirement 47 CFR §90.210(d) and IC RSS-119 section 5.8.3 - Emission Limits – “D-Mask”: Emission Mask D. For transmitters designed to operate with a 12.5 kHz channel bandwidth, any emission must be attenuated below the power (P) of the highest emission contained within the authorized bandwidth as follows: (1) On any frequency from the center of the authorized bandwidth (f0) to 5.625 kHz removed from f0: Zero dB (2) On any frequency removed from the center of the authorized bandwidth by a displacement frequency (f d in kHz) of more than 5.625 kHz but no more than 12.5 kHz: At least 7.27 *( f d –2.88 kHz) dB (3) On any frequency removed from the center of the authorized bandwidth by a displacement frequency (f d in kHz) of more than 12.5 kHz: At least 50 plus 10 log 10…

Text truncated - open the document above for the full version.