ACJ9TGCF-194Personal Computer

1 Contents Precautions ...............................................................................2 Names and Functions of Parts .................................................4 Supplementary Instructions for HSDPA/UTMS Modem Model No. CF-19 Series Personal Computer 2 The following safety precautions must be observed during all phases of the operation, usage, service or repair of any Personal Computer or Handheld Computer incorporating WWAN. Manufacturers of the cellular terminal are advised to convey the following safety information to users and operating person- nel and to incorporate these guidelines into all manuals supplied with the product. Failure to comply with these precautions violates safety standards of design, manufacture and intended use of the prod- uct. Panasonic assumes no liability for customer failure to comply with these precautions. When in a hospital or other health care facility, observe the restrictions on the use of mobiles. Switch Personal Computer or Handheld Computer incorporating WWAN off, if instructed to do so by the guidelines posted in sensitive areas. Medical equipment may be sensitive to RF energy. The operation of cardiac pacemakers, other implanted medical equipment and hearing aids can be affected by interference from Personal Computer or Handheld Computer in- corporating WWAN placed close to the device. If in doubt about potential danger, contact the physician or the manufacturer of the device to verify that the equipment is properly shielded. Pacemaker patients are advised to keep their Personal Computer or Handheld Computer incorporating WWAN away from the pacemaker, while it is on. Switch off Personal Computer or Handheld Computer incorporating WWAN before board- ing an aircraft. Make sure it cannot be switched on inadvertently. The operation of wireless appliances in an aircraft is forbidden to prevent interference with communications systems. Failure to observe these instructions may lead to the suspension or denial of cellular ser- vices to the offender, legal action, or both. Do not operate Personal Computer or Handheld Computer incorporating WWAN in the presence of fl ammable gases or fumes. Switch off the cellular terminal when you are near petrol stations, fuel depots, chemical plants or where blasting operations are in progress. Operation of any elec- trical equipment in potentially explosive atmospheres can constitute a safety hazard. Your Personal Computer or Handheld Computer incorporating WWAN receives and trans- mits radio frequency energy while switched on. Remember that interference can occur if it is used close to TV sets, radios, computers or inadequately shielded equipment. Follow any special regulations and always switch off Personal Computer or Handheld Computer incor- porating WWAN wherever forbidden, or when you suspect that it may cause interference or danger. Road safety comes fi rst! Do not use a Personal Computer or Handheld Computer incorporating WWAN while driving a vehicle. Do not place the computer with WWAN in an area where it could cause personal injury to the driver or passengers. It is recommended to stow the unit in the boot or secure stowage area while driving. Do not place the computer with WWAN in an area over an air bag or in the vicinity where an air bag may deploy. Air bags infl ate with great force and if the computer with WWAN is placed in the air bag deploy- ment area may be propelled with great force and cause serious injury to occupants of the vehicle. IMPORTANT! Personal Computer or Handheld Computer incorporating WWAN operate using radio sig- nals and cellular networks cannot be guaranteed to connect in all conditions. Therefore, you should never rely solely upon any wireless device for essential communications, for example emergency calls. Remember, in order to make or receive calls, Personal Computer or Handheld Computer in- corporating WWAN must be switched on and in a service area with adequate cellular signal strength. Some networks do not allow for emergency calls if certain network services or phone features are in use (e.g. lock functions, fi xed dialing etc.). You may need to deacti- vate those features before you can make an emergency call. Safety Precautions Precautions 3 Some networks require that a valid SIM card be properly inserted in Personal Computer or Handheld Computer incorporating WWAN. 27-E-1-1 Federal Communications Commission Radio Frequency Interference Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital de- vice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc- tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular in- stallation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equip- ment and receiver. Connect the equipment into an outlet on a cir- cuit different from that to which the receiver is connected. Consult the Panasonic Service Center or an experienced radio/TV technician for help. Warning To assure continued compliance, use only shielded interface cables when connecting to a computer or peripheral. Also, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. FCC RF Exposure Warning: This equipment is provided with PC Card slot that could be used with wireless transmitters, which will be specifically recommended wh…

Text truncated - open the document above for the full version.

Contents Getting Started OPERATING INSTRUCTIONS Personal Computer Model No. CF-19 series Introduction ................................................................. 2 Read Me First ............................................................. 3 Description of Parts .................................................. 10 First-time Operation .................................................. 13 Useful Information On-screen Manual .................................................... 16 Handling and Maintenance ....................................... 17 Hard Disk Backup Function (Recover Pro) .............. 19 Hard Disk Data Erase Utility ..................................... 21 Reinstalling Software ................................................ 22 Troubleshooting Error Code/Message ................................................ 24 Troubleshooting (Basic) ............................................ 25 Hardware Diagnostics .............................................. 29 Appendix LIMITED USE LICENSE AGREEMENT ................... 32 Specifi cations ........................................................... 34 LIMITED WARRANTY .............................................. 36 Please read these instructions carefully before using this product and save this manual for future use. For further information about the com- puter, you can refer to the on-screen manual. To access the on-screen manual Î page 16 “On-screen Manual” Getting Started Useful Information Troubleshooting Appendix Introduction Thank you for purchasing this Panasonic computer. For optimum performance and safety, please read these instruc­ tions carefully. „ Terms and illustrations in these instructions Getting Started CAUTION : Conditions that may result in minor or moderate injury. NOTE : Useful and helpful information. Enter : Press [Enter] key. Fn + F5 : Press and hold [Fn] key, and then press [F5] key. [start] - [Run] : Click [start], and then click [Run]. You may need to double-click in some cases. Î : Page in these Operating Instructions or in the Reference Manual. : Reference to the on-screen manuals. z Some illustrations are simplified to help your understanding and may look different from the actual unit. z If you do not log on as an administrator, you cannot use some functions or cannot display some screens. z Refer for the latest information about optional products to the catalogs, etc. z In these instructions, the names and terms are referred as follows. y “Microsoft ® Windows ® XP Professional Service Pack 2 with Advanced Security Technologies” as “Windows”, “Win­ dows XP” or “Windows XP Professional” y “Microsoft ® Windows ® XP Tablet PC Edition 2005” as “Windows”, “Windows XP” or “Windows XP Tablet PC Edi­ tion” y DVD-ROM & CD-R/RW drive, and DVD MULTI drive as “CD/DVD drive” y Circular media including DVD-ROM and CD-ROM as “discs” z The display modes are referred as follows. ( ) indicates the terms in [Intel ® Graphics Media Accelerator Driver for Mobile] screen. To display the screen, click [start] - [Control Panel] - [Other Control Panel Options] - [Intel(R) GMA Driver for Mobile]. y Internal LCD (Notebook): The computer’s display y External display (Monitor): External display y Simultaneous display (Intel ® Dual Display Clone): The same screen is displayed on the internal LCD and the ex­ ternal display. y Extended desktop: The extended working area across the internal LCD and the external display. „ Copyright This manual is copyrighted by Matsushita Electric Industrial Co., Ltd. with all rights reserved. No part of this manual may be reproduced in any form without the prior written permission of Matsushita Electric Industrial Co., Ltd. No patent liability is assumed with respect to the use of the information contained herein. © 2006 Matsushita Electric Industrial Co., Ltd. All Rights Reserved. „ Disclaimer Computer specifications and manuals are subject to change without notice. Matsushita Electric Industrial Co., Ltd. as­ sumes no liability for damage incurred directly or indirectly from errors, omissions or discrepancies between the com­ puter and the manuals. „ Trademarks Microsoft ® , Windows ® , the Windows logo and IntelliMouse are registered trademarks of Microsoft Corporation of the United States and/or other countries. Intel, Core, Centrino and PROSet are either registered trademarks or trademarks of Intel Corporation. SD Logo is a trademark. Adobe, the Adobe logo and Adobe Reader are either registered trademarks or trademarks of Adobe Systems Incorpo­ rated in the United States and/or other countries. PhoenixBIOS, Phoenix Always and Recover Pro are trademarks and/or registered trademarks of Phoenix Technolo­ gies Ltd. Bluetooth™ is a trademark owned by Bluetooth SIG, Inc., U.S.A. and licensed to Matsushita Electric Industrial Co., Ltd. Panasonic ® is a registered trademark of Matsushita Electric Industrial Co., Ltd. Names of products, brands, etc., appearing in this manual are trademarks or registered trademarks of their respective own companies. 2 Read Me First Models for U.S.A. Federal Communications Commission Radio Fre­ quency Interference Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal­ lation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer­ ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: z Reorient or relocate the receiving antenna. z Increase t…

Text truncated - open the document above for the full version.

Panasonic Corporation of North America One Panasonic Way 4B-8 Secaucus, NJ 07094 Tel: 201-348-7758 / Fax: 201-392-4564 [email protected] RICHARD MULLEN Group Manager Product Safety and Compliance Division January 23, 2007 ITPD-06-F026A: BT Part 15C / DSS / EA866610 ITPD-06-F026B: WLAN Part 15C / DTS / EA652874 ITPD-06-F026C: UNII Part 15E / NII / EA560561 ITPD-06-F026D: HSDPA Parts 22H, 24E / PCB / EA465249 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: Authority to Act as FCC Agent for Panasonic Portable Personal Computer Model CF-19 Family With Taiyo Bluetooth, Intel WLAN(a+b+g) and Novatel HSDPA FCC Certification for FCC ID: ACJ9TGCF-194 To Whom It May Concern: On behalf of Panasonic Corp. of North America, we herby authorize PCTEST Engineering Laboratory, Inc., to act on our behalf in matters relating to FCC equipment authorization, including the signing of documents relating to these matters. Any and all acts carried out by PCTEST on our behalf shall have the same effect as acts of our own. This project represents Panasonic Portable Personal Computer, Model CF-19 Family with Intel Core Duo 1.06 GHz and Tablet LCD with side panel spacers, which will be marketed under FCC ID: ACJ9TGCF-194. Under this filing, the Intel WLAN's Part 15E Unlicensed National Information Infrastructure’s 5260~5320 MHz high band has been disabled. The U-NII feature will not be enabled until after a FCC certified access point becomes available on the marketplace to enable performance of DFS tests to be performed on this end-product, which operates in only the client mode without radar detection, ad-hoc and peer-to-peer capabilities. The DFS tests will be performed on 5.15~5.25 GHz U-NII frequency band and filed under a Class II Permissive Change application. This product will be marketed with the following co-located transmitters: (1) Taiyo Yuden Bluetooth, Model EYS1CSMX (Taiyo Yuden has no FCC ID): FCC Rule Part Type Freq Range (MHz) Output Watts Part 15C DSS 2402~2480 0.0191 (2) Intel WLAN (a+b+g), Model WM3945ABG (Intel FCC ID: PD9WM3945ABG) FCC Rule Part Type Freq Range (MHz) Output Watts Part 15C 802.11(b) 2412~2462 0.0294 Part 15C 802.11(g) 2412~2462 0.0265 Part 15C 802.11(a) 5745~5825 0.0266 Part 15E 802.11(a) Low Band 5180~5240 0.0204 (3) Novatel HSDPA, Model EU730 (Novatel FCC ID: NBZNRM-EU730) Novatel FCC Grant Notes: Quad Band GPRS/EDGE & UMTS FCC Rule Part Type Freq Range (MHz) Output Watts Emission Designator Part 22H Cellular GPRS 824.2~848.8 1.5 W ERP 278KGXW Part 22H Cellular HSDPA 826.4~846.6 0.184 W ERP 4M17F9W Part 24E PCS GPRS 1850.2~1909.8 0.816 W EIRP 277KGXW Part 24E PCS HSDPA 1852.4~1907.6 0.197 W EIRP 4M17F9W Panasonic Corporation of North America One Panasonic Way 4B-8 Secaucus, NJ 07094 Tel: 201-348-7758 / Fax: 201-392-4564 [email protected] RICHARD MULLEN Group Manager Product Safety and Compliance Division The highest reported SAR values measured with LCD spacers was: BT Body SAR (2.4 GHz) 0.036 W/kg with LCD flip 802.11a Body SAR (5.2 GHz) 0.561 W/kg at zero spacing 802.11b Body SAR (2.4 GHz) 0.074 W/kg at zero spacing 802.11a Body SAR (5.8 GHz) 1.30 W/kg at zero spacing 802.11g Body SAR (2.4 GHz) 0.129 W/kg at 1.5 cm spacing Part 22H WCDMA-HSDPA Body SAR (826.4~846.6 MHz) 0.146 W/kg with LCD flip Part 24E PCS WCDMA-HSDPA Body SAR (1852.4~1907.6 MHz) 0.220 W/kg with LCD flip This PC contains the following Inverted-F type transmitter antennas, which are all located within the LCD panel: (1) BT TX/RX antenna with 3.06 dBi antenna gain; (2) WLAN Main TX/RX and Aux TX/RX antennas with 2.48 dBi and 3.31 dBi antenna gains; and (3) HSDPA Main TX/RX antennas with 1.84 dBi and Aux Rx only antenna. The PC’s main User Manual gives all FCC required notices and warning, including RF Exposure Warning. In accordance with provisions of Section 0.457(d) of the Commission’s Rules and Section 552(b)(4) of the Freedom of Information Act, we request permanent confidentiality for transmitter’s exhibits, which contain Operation Description, Parts Lists & Tune-Up Procedure, Block Diagram and Schematic Diagram. The BT and WLAN transmitters are not user adjustable and do not have a Tune-Up Procedure. These exhibits contain proprietary, confidential and trade secrets material, which would not be routinely made available for public inspection. Also, in accordance with FCC Public DA 04-1705, we request short-term confidentiality for exhibits, which contain External Photographs, Internal Photographs, Test Setup Photographs and the User Manual. These exhibits contain pre-market information, which could give our competitors unfair advantage should this information be released before this product is actually introduced into the common marketplace. Sincerely yours, Richard Mullen Richard Mullen Group Manager

Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification - FCC ID: NBZNRM-EU730 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Integration Guide Technical Specification Schematics Bill of Materials / Part List Block Diagrams The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Kevin Goodfellow Technical Specialist December 10, 2005

To: Andrew Leimer / FCC Application Processing Branch From: Richard Mullen / Panasonic FCC ID: ACJ9TGCF-194 Applicant: Panasonic Corporation of North America Subject: Personal Computer CF-19+BT+WLAN+HSDPA Date: March 20, 2007 PO Control No. Equipment Type and FCC Rule Part 731 Confirmation CRN ITPD-06-F026A BT Part 15C EA866610 32712 ITPD-06-F026B WLAN Part 15C EA652874 32710 ITPD-06-F026C UNII Part 15E EA560561 32711 ITPD-06-F026D HSDPA Parts 22H, 24E EA465249 32709 FCC comment dated March 20, 2007: Please amend SAR report to include device setup info per FCC Lab WCDMA / HSDPA procedures. Panasonic answer dated March 20, 2007: Today we uploaded SAR Test Report Section 13, which contains the FCC 3G Measurement Procedures, which includes HSDPA and WCDMA test results.

< CF-19 WLANabg BlueTooth & HSDPA model photo> 1. Top and Front View

<CF-19 WLANa+b+g & BlueTooth & HSDPA model’s Label Description> 1) FCCID Label 2) FCC DoC Logo FCC ID: ACJ9TGCF-194 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC DoC LABELFCC ID LABEL

2. Module Position HSDPA Module WLAN Module Reverse side of HSDPA PWB Reverse Side BlueTooth Module 3. Module Photo 1) WLAN WLAN Exterior Top View WLAN Exterior Bottom View WLAN inside Top View WLAN inside Bottom View 2) BlueTooth BlueTooth Card Top View BlueTooth Card Bottom View BlueTooth Module inside Top View BlueTooth Module inside Bottom View FCCID:WM3945ABG 3) HSDPA Photo HSDPA Top View EVDO Bottom View HSDPA Inside Top View HSDPA Inside Bottom View 4. Antenna Position HSDPA TX/RX Antenna WLAN Main TX/RX Antenna BlueTooth TX/RX Antenna WLAN AUX TX/RX Antenna WLAN Main TX/RX Antenna WLAN AUX TX/RX Antenna BlueTooth TX/RX Antenna HSDPA TX/RX Antenna 5) Antenna Specification WLAN Main TX/RX Antenna: Pattern Antenna (Inverted F type: 2.48dBi max) WLAN Aux TX/RX Antenna: Pattern Antenna (Inverted F type: 3.31dBi max) Bluetooth TX/RX Antenna: Pattern Antenna (Inverted F type: 3.06dBi max) HSDPA TX/RX Antenna: Pattern Antenna (Inverted-F type: 1.84dBi max)

APPENDIX A: SAR TEST DATA PCTEST ENGINEERING LABORATORY, INC. DUT: CF-19; Type: Panasonic Notebook PC with WLAN + Bluetooth + HSDPA; Sample #7 Communication System: WCDMA850; Frequency: 835 MHz;Duty Cycle: 1:1 Medium: 835 Muscle ( σ = 0.97 mho/m, ε r = 53.71, ρ = 1000 kg/m 3 ) Phantom section: Flat Section; Bystander Position; Space: 1.5 cm Test Date: 10-19-2006; Ambient Temp: 23.5°C; Tissue Temp: 21.3°C Probe: EX3DV4 - SN3550; ConvF(7.56, 7.56, 7.56); Calibrated: 1/18/2006 Sensor-Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 Sn665; Calibrated: 9/4/2006 Phantom: SAM with CRP; Type: SAM; Serial: TP1375 Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Mode: 850 HSDPA, Bystander position, LCD Open, Mid.ch Area Scan (5x17x1): Measurement grid: dx=15mm, dy=15mm Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 7.24 V/m Peak SAR (extrapolated) = 0.064 W/kg SAR(1 g) = 0.043 mW/g; SAR(10 g) = 0.029 mW/g 0 dB = 0.049mW/g PCTEST ENGINEERING LABORATORY, INC. DUT: CF-19; Type: Panasonic Notebook PC with WLAN + Bluetooth + HSDPA; Sample #7 Communication System: WCDMA850; Frequency: 835 MHz;Duty Cycle: 1:1 Medium: 835 Muscle ( σ = 0.97 mho/m, ε r = 53.71, ρ = 1000 kg/m 3 ) Phantom section: Flat Section; Laptop Position; Space: 0.0 cm Test Date: 10-19-2006; Ambient Temp: 23.5°C; Tissue Temp: 21.3°C Probe: EX3DV4 - SN3550; ConvF(7.56, 7.56, 7.56); Calibrated: 1/18/2006 Sensor-Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 Sn665; Calibrated: 9/4/2006 Phantom: SAM with CRP; Type: SAM; Serial: TP1375 Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Mode: 850 HSDPA, Laptopt position, LCD Flip, Mid.ch Area Scan (6x17x1): Measurement grid: dx=15mm, dy=15mm Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 6.02 V/m Peak SAR (extrapolated) = 0.044 W/kg SAR(1 g) = 0.028 mW/g; SAR(10 g) = 0.018 mW/g 0 dB = 0.034mW/g PCTEST ENGINEERING LABORATORY, INC. DUT: CF-19; Type: Panasonic Notebook PC with WLAN + Bluetooth + HSDPA; Sample #7 Communication System: WCDMA850; Frequency: 835 MHz;Duty Cycle: 1:1 Medium: 835 Muscle ( σ = 0.97 mho/m, ε r = 53.71, ρ = 1000 kg/m 3 ) Phantom section: Flat Section; LCD Left Side; Space: 0.0 cm Test Date: 10-19-2006; Ambient Temp: 23.5°C; Tissue Temp: 21.3°C Probe: EX3DV4 - SN3550; ConvF(7.56, 7.56, 7.56); Calibrated: 1/18/2006 Sensor-Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 Sn665; Calibrated: 9/4/2006 Phantom: SAM with CRP; Type: SAM; Serial: TP1375 Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Mode: 850 HSDPA, Tablet position, Right side, LCD Flip, Mid.ch Area Scan (7x17x1): Measurement grid: dx=15mm, dy=15mm Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 12.7 V/m Peak SAR (extrapolated) = 0.202 W/kg SAR(1 g) = 0.133 mW/g; SAR(10 g) = 0.085 mW/g 0 dB = 0.158mW/g PCTEST ENGINEERING LABORATORY, INC. DUT: CF-19; Type: Panasonic Notebook PC with WLAN + Bluetooth + HSDPA; Sample #7 Communication System: WCDMA1900; Frequency: 1880 MHz;Duty Cycle: 1:1 Medium: 1900 Muscle ( σ = 1.57 mho/m, ε r = 53.63, ρ = 1000 kg/m 3 ) Phantom section: Flat Section; Bystander Position; Space: 1.5 cm Test Date: 10-19-2006; Ambient Temp: 23.6°C; Tissue Temp: 21.7°C Probe: EX3DV4 - SN3550; ConvF(6.3, 6.3, 6.3); Calibrated: 1/18/2006 Sensor-Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 Sn665; Calibrated: 9/4/2006 Phantom: SAM with CRP; Type: SAM; Serial: TP1375 Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Mode: 1900 HSDPA, Bystander position, LCD Open, Mid.ch Area Scan (5x17x1): Measurement grid: dx=15mm, dy=15mm Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 9.19 V/m Peak SAR (extrapolated) = 0.162 W/kg SAR(1 g) = 0.106 mW/g; SAR(10 g) = 0.067 mW/g 0 dB = 0.126mW/g PCTEST ENGINEERING LABORATORY, INC. DUT: CF-19; Type: Panasonic Notebook PC with WLAN + Bluetooth + HSDPA; Sample #7 Communication System: WCDMA1900; Frequency: 1880 MHz;Duty Cycle: 1:1 Medium: 1900 Muscle ( σ = 1.57 mho/m, ε r = 53.63, ρ = 1000 kg/m 3 ) Phantom section: Flat Section; Laptop Position; Space: 0.0 cm Test Date: 10-19-2006; Ambient Temp: 23.6°C; Tissue Temp: 21.7°C Probe: EX3DV4 - SN3550; ConvF(6.3, 6.3, 6.3); Calibrated: 1/18/2006 Sensor-Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 Sn665; Calibrated: 9/4/2006 Phantom: SAM with CRP; Type: SAM; Serial: TP1375 Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Mode: 1900 HSDPA, Laptopt position, LCD Flip, Mid.ch Area Scan (6x17x1): Measurement grid: dx=15mm, dy=15mm Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 6.73 V/m Peak SAR (extrapolated) = 0.101 W/kg SAR(1 g) = 0.053 mW/g; SAR(10 g) = 0.029 mW/g 0 dB = 0.068mW/g PCTEST ENGINEERING LABORATORY, INC. DUT: CF-19; Type: Panasonic Notebook PC with WLAN + Bluetooth + HSDPA; Sample #7 Communication System: WCDMA1900; Frequency: 1880 MHz;Duty Cycle: 1:1 Medium: 1900 Muscle ( σ = 1.57 mho/m, ε r = 53.63, ρ = 1000 kg/m 3 ) Phantom section: Flat Section; LCD Right Side; Space: 0.0 cm Test Date: 10-19-2006; Ambient Temp: 23.6°C; Tissue Temp: 21.7°C Probe: EX3DV4 - SN3550; ConvF(6.3, 6.3, 6.3); Calibrated: 1/18/2006 Sensor-Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 Sn665; Calibrated: 9/4/2006 Phantom: SAM with CRP; Type: SAM; Serial: TP1375 Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 Mode: 1900 HSDPA, Tablet position, Right side, LCD Flip, Mid.ch Area Scan (7x17x1): Measurement grid: dx=15mm, dy=15mm Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 13.0 V/m Peak SAR (extrapolated) = 0.329 W/kg SAR(1 g) = 0.210 mW/g; SAR(10 g) = 0.122 mW/g 0 dB = 0.255mW/g PCTEST ENGINEERING LABORATORY, INC. DUT: CF-19; Type: Panasonic Notebook PC with…

Text truncated - open the document above for the full version.

Reviewed by: FCC ID: ACJ9TGCF-194 CERTIFICATION REPORT Quality Manager SAR Filename: Test Dates: EUT Type: 0610040879 10/17/2006 - 10/20/2006 Toughbook Model: CF-19 Page 1 of 25 © 2006 PCTEST Engineering Laboratory, Inc. v 3.2 Applicant Name: Date of Testing: Panasonic Corporation of North America 10/17/2006 - 10/20/2006 One Pnasonic Way, 4B-8 Test Site/Location: Secaucus, NJ 07094 PCTEST Lab, Columbia, MD, USA Test Report Serial No.: 0610040879 FCC ID: ACJ9TGCF-194 APPLICANT: PANASONIC CORPORATION OF NORTH AMERICA EUT Type: Toughbook Model: CF-19 Application Type: Certification FCC Rule Part(s): §2.1093; FCC/OET Bulletin 65 Supplement C [July 2001] FCC Classification: FCC Part 15 Frequency Hopping Spread Spectrum Transceiver (DSS) Unlicensed National Information Infrastructure (UNII) Digital Transmission System (DTS) PCS Licensed Transmitter (PCB) Model(s): CF-19 Tx Frequency: 2412 - 2462MHz (DSS/OFDM) / 5745 - 5825MHz (OFDM)/ 5180 – 5240MHz (UNII)/ 826.4 – 846.6 MHz (WCDMA)/ 1852.4 – 1907.6 MHz (PCS WCDMA) Conducted Power: 14.25 dBm Conducted (a) 14.68 dBm Conducted (b) 14.24 dBm Conducted (g) 19.099 mW (12.81 dBm) Bluetooth Conducted / 13.09 dBm (UNII Low Band) 0.302 W ERP WCDMA (24.799dBm)/ 0.365 W EIRP PCS WCDMA (25.626dBm) Max. SAR Measurement: 0.074 W/kg 802.11b Body SAR / 0.036 W/kg Bluetooth Body SAR 0.561 W/kg 802.11a 5.2GHz Body SAR/ 1.30 W/kg 802.11a 5.8GHz Body SAR 0.133 W/kg WCDMA Body SAR/ 0.210 W/kg PCS WCDMA Body SAR Test Device Serial No.: Pre-Production [S/N: N/A] This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-2005 and had been tested in accordance with the measurement procedures specified in FCC/OET Bulletin 65 Supplement C (2001) and IEEE Std. 1528-2003. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Grant Conditions: . SAR compliance for body-worn operating configuration is based on a separation distance of 1.5 cm between the bottom of the unit and the body of the user. End-users must be informed of the body-worn operating requirements for satisfying RF exposure compliance. PCTEST certifies that no party to this application has been denied the FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. PCTEST ENGINEERING LABORATORY, INC. 6660-B Dobbin Road, Columbia, MD 21045 USA Tel. 410.290.6652 / Fax 410.290.6554 http://www.pctestlab.com CERTIFICATE OF COMPLIANCE (SAR EVALUATION) Reviewed by: FCC ID: ACJ9TGCF-194 CERTIFICATION REPORT Quality Manager SAR Filename: Test Dates: EUT Type: 0610040879 10/17/2006 - 10/20/2006 Toughbook Model: CF-19 Page 2 of 25 © 2006 PCTEST Engineering Laboratory, Inc. v 3.2 TABLE OF CONTENTS 1 INTRODUCTION ............................................................................................................................. 3 2 TEST SITE LOCATION ................................................................................................................... 4 3 SAR MEASUREMENT SETUP ....................................................................................................... 5 4 DASY E-FIELD PROBE SYSTEM .................................................................................................. 7 5 PROBE CALIBRATION PROCESS ................................................................................................ 8 6 PHANTOM AND EQUIVALENT TISSUES...................................................................................... 9 7 DOSIMETRIC ASSESSMENT & PHANTOM SPECS................................................................... 10 8 DEFINITION OF REFERENCE POINTS ......................…

Text truncated - open the document above for the full version.