AHV-SID2HMI controller

Additional Type Approval information and Safety Precautions/Warnings! Legal Statements for SID 2.0 D-000849 SID_TA_Information_leaflet.docx rev: C 19w27 This document contains Additional Type Approval information such as type approval symbols, numbers and texts for the SID 2.0 unit required by national authorities and where this information is not found on the device itself due to limited space. Legal Statements and Safety Precautions/Warnings for the SID 2.0 unit required by national authorities. Country/ Region Additional Type Approval Information - Statements/Precautions/Warnings! Canada Contains IC: 10224A-201903EG25G This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions. (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. USA Contains FCC ID: XMR201903EG25G This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions. (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. NOTICE: Changes or modifications made to this equipment not expressly approved by (manufacturer name) may void the FCC authorization to operate this equipment. Radio frequency radiation exposure Information: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter should not be co-located or operating in conjunction with any other antenna or transmitter.

Load Assist Foreword This appendix is intended to serve as a supplement to the Operator’s Manual of the machine and should be read together with the manual. Keep the appendix, together with the Operator’s Manual of the machine, in the cab, so that it is always at hand. Replace it immediately, if it is lost. NOTE! If this appendix covers more than one machine, the information applies to all machines unless otherwise indicated. A lot of work has been spent on the machine's design and manufacture to make it as effective and safe as possible. Accidents that occur in despite of this can most often be contributed to the human factor. A safety-conscious person and a well-maintained machine make a safe, efficient, and profitable combination. Therefore, read the safety instructionsand follow them. We continuously strive to improve our products and to make them more effective by changes to their design. We reserve the right to do this without committing ourselves to introduce these improvements on already delivered products. We also reserve the right to change data and equipment, as well as instructions for service and maintenance without prior notice. OPERATOR'S MANUAL Table of contents Load Assist TPMS Safety regulations It is the operator's obligation to know and follow the applicable national and local safety regulations. The safety instructions in this manual only apply to cases where there are no national or local regulations. Alphabetical index PUB 20049540-G The original language is English. Original instructions. 2021.05 Copyright © 2021, Volvo Construction Equipment. All rights reserved. 2 Foreword DANGER The safety symbol combined with this signal word indicates a hazardous situation which, if not avoided, will result in deathor serious injury. Danger is limited to the most extremesituations. WARNING The safety symbol combined with this signal word indicates a hazardous situation which, if not avoided, could result in deathor serious injury. CAUTION The safety symbol combined with this signal word indicates a hazardous situation which, if not avoided, could result in moderate or minor injury. NOTICE Indicates a potentially hazardous situation which may result in machine damage. NOTE! It is used to highlight information for installing, use, or maintenance that is important but is not safety-related. Table of contents 3 Table of contents Foreword .........................................................1 Load Assist.....................................................5 Screen views ................................................... 6 Settings ......................................................... 12 Load weighing ............................................... 38 Task mode .................................................... 61 Map ............................................................... 69 Rear vision system ...................................... 117 View selector ............................................... 118 Messages .................................................... 119 Maintenance ................................................ 121 TPMS ............................................................ 122 Settings ....................................................... 124 Alphabetical index .................................. 129 Load Assist 5 A B V1151437 A Display B Recommended location for printer Load Assist Load Assist is intended to be used as an information system to facilitate the user’s tasks. This appendix does not release the operator from following the instructions and cautionary measures described in the ordinary operator’s manual to the machine. Load Assist is a feature in the Co-pilot. It is basing on the load weighing system and can be complemented with features like: Task mode, see page 61. Map, see page 69. Rear vision system, see page 117. Load Weighing is a system that weighs the load in/ on the attachment during a continuous lifting motion. An audible signal confirms that the weight is measured correctly. The system summarizes the load in every cycle and the progress can be followed in the display. For more information, see page 40. Running-in instructions New machines may need up to 200 working hours to reach a stable accuracy due to the initially higher friction in the boom linkage but should be used as normal during the running-in period. Known weight calibration is recommended after the first 200 working hours to maintain a good weighing accuracy when using these buckets. Regular greasing is important to maintain a low friction in the lift arm system. Follow the greasing intervals in the machine Operator's Manual. Central lubrication system is recommended. Load Assist 6Screen views Screen views Load Assist 8Screen views Main screen NOTE! The appearance of the main screen differs depending on the current settings etc. NOTE! The main screen information here is shown as when Known weight calibrated buckets are used. There are two decimals on load value when Known weight calibrated buckets are used and one decimal when other attachments are used. Appearance and items also differ slightly between these two accuracy levels. Load Assist 9Screen views Settings 1. Settings, see page 12. Load weighing 2. Current load, see page 42. 3. Locked/unlocked load, see page 43. 4. Forced unload, see page 45. 5. Forced partial unloading, see page 46. 6. Attachment type, see page 43. 7. Attachment angle, see page 43. 8. Known weight calibrated buckets, see page 44. 9. Weight adjustment of the current attachment, see page 57. 10. Machine inclination, transversal (“roll”), see page 44. 11. Boom angle, see page 45. 12. Machine inclination, longitudinal (“pitch”), see page 45. Task mode 13. Task mode, see page 61. 14. Delete last load, see page 65. 15. Pause view, see page 65. 16. Print receipt, see page 65. Map 17. Centering/Compass view, see page 77. Rear vision system 18. Rear vision system, see page 117. Others 19. View selector, see page 118. 20. Messages, see page …

Text truncated - open the document above for the full version.

CPAC SYSTEMS AB Bergskroken 3 SE-431 37 Mölndal Phone: +46 (0)31 352 16 00 Fax: +46 (0)31 352 16 99 www.cpacsystems.se Copyright by CPAC Systems AB. All rights reserved Attention: Application Examiner Re: Covered List, located at https://www.fcc.gov/supplychain/coveredlist and 47 CFR parts §2.903 and §2.911(d)(5)(ii) of the FCC rules Applicant: CPAC Systems AB FCC ID: AHV-SID2 To whom it may concern, CPAC Systems AB (“Applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to 47 CFR part §2.903 of the FCC rules and does not originate directly or indirectly from any company named on the covered list located in the link above or any subsidiary or affiliate thereof. Applicant further certifies that, as of the date of the filing of the application, the Applicant is not identified on the Covered List as an entity producing “covered” equipment and is not a subsidiary or affiliate of any such entity pursuant to 47 CFR part §1.50002 and required by 47 CFR part §2.911(d)(5)(ii) of the FCC rules. I HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant and agree to immediately notify Nemko Scandinavia AS if there is any change in the status identified above. Emma Lindqvist Regulatory Affairs Manager CPAC Systems AB 2023/04/26

CPAC SYSTEMS AB Bergskroken 3 SE-431 37 Mölndal Phone: +46 (0)31 352 16 00 Fax: +46 (0)31 352 16 99 www.cpacsystems.se Copyright by CPAC Systems AB. All rights reserved Attention: Application Examiner Re: Certification designating a U.S. agent for service of process pursuant to section 2.911(d)(7) of the FCC rules To whom it may concern, This letter is to confirm both Volvo Construction Equipment North America, LLC (“Agent”) and CPAC Systems AB (“Applicant”) acknowledge consent to obligations of each party pursuant to 47 CFR part §2.911(d)(7) of the FCC rules in regard to the agent for service of process. I, Emma Lindqvist HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant. I further acknowledge the requirement to maintain an agent extends for no less than one year after the termination of all marketing and importation or the conclusion of and commission-related proceeding involving the equipment and agree to immediately notify the FCC and Nemko Scandinavia AS if there is any change in the status identified above. Applicant Company Name: CPAC Systems AB Contact Name : Emma Lindqvist Address: Bergskroken 3, 401 26 Gothenburg, Sweden Telephone No : +467055948961 Email: [email protected] Applicant FRN: 0025650813 Signature: ____________________________________ Date: 2023/05/02___________________________________ I John Bartz, HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Agent. I consent to the obligation to accept service of process on behalf of the applicant in regard to all certification applications to the FCC submitted by above applicant and agree to immediately notify the FCC and Nemko Scandinavia AS if there is change in this representation. Agent Company Name: Volvo Construction Equipment North America, LLC Contact Name: John Bartz Address: 304 Volvo Way, Shippensburg, PA, 17257 Telephone No: 828 674-5456 Email: [email protected] Agent FRN: 0025715467 Signature: Date: 5/3/2023

CPAC SYSTEMS AB Bergskroken 3 SE-431 37 Mölndal Phone: +46 (0)31 352 16 00 Fax: +46 (0)31 352 16 99 www.cpacsystems.se Copyright by CPAC Systems AB. All rights reserved 1/9/2023 Nemko North America, Inc. 303 River Road Ottawa, Ontario, Canada K1V 1H2 AUTHORITY TO ACT AS AGENT - FCC On our behalf, I appoint Nemko North America, Inc., to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in FCC regulations will have affixed to it a label identical to that submitted for approval with this application. In signing this letter, Applicant certifies that neither the applicant nor any party to the application is not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. § 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko North America Inc., still resides still resides with us. Sincerely, Printed name: Emma Lindqvist

CPAC SYSTEMS AB Bergskroken 3 SE-431 37 Mölndal Phone: +46 (0)31 352 16 00 Fax: +46 (0)31 352 16 99 www.cpacsystems.se Copyright by CPAC Systems AB. All rights reserved 3/30/2023 Nemko North America, Inc. 303 River Road Ottawa, Ontario, Canada K1V 1H2 REQUEST FOR CONFIDENTIALITY - FCC FCC ID: AHV‐SID2 Pursuant to Sections 0.457(d) and 0.459 of the Commission’s Rules and FCC Guidance document 726920, we hereby request confidential treatment of information accompanying this application as outlined below: PERMANENT LONG-TERM CONFIDENTIALITY: Schematics Bill of Materials/Parts List Block Diagrams Theory of Operation When the device is marketed before the requested number of days listed above, the grantee will inform the TCB to release the Short-Term Confidentiality information withheld on the FCC equipment authorization website. The above information contains trade secrets and proprietary information not customarily released to the public. The public disclosure of this information might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Sincerely, Signed : Printed name: Emma Lindqvist Title: Regulatory Affairs Manager

Label dimensions (W x H): 55 ±1 mm x 30 ±1 mm, corners R1±0,5 mm Model name: SID 2.0 Manufacturer: CPAC Systems AB Box 217 SE-40123 Gothenburg, SWEDEN Brand name:CPAC Country of origin: SLOVAKIA SID 2.0 Homologation label FCC ID: AHV-SID2 IC:10111-SID2 Contains FCC ID:XMR201903EG25G Contains IC ID:10224A-201903EG25G Rating: 12-24VDC 12VDC<15A 24VDC<10A

1 Jin Xu From:Emma Lindqvist <[email protected]> Sent:Friday, July 7, 2023 7:04 AM To:Rahul Sankhayan; Daniel Wasell Subject:Fwd: Hydra mainboard photos [EXTERNAL EMAIL] Hi Rahul, See photos attached. Med vänlig hälsning Emma Lindqvist 2 3 4

FCC ID: AHV-SID2 FCC RF Exposure Compliance for Simultaneous Operations Configurations for Simultaneous OperationsConfiguration 1: BT/BLE + GSM/WCDMA/LTEConfiguration 2: WiFi 2.4 + GSM/WCDMA/LTEPower Density is calculated from Maximum Conducted Power and Antenna Gain at prediction distanceMaximum of Conducted and Radiated Output Power is used in the calculation. Therefore negative values for antenna gain have been replaced by 0 dBi. RF Function BT BLE WiFi 2.4 GSM850 GSM1900 WCDMA B2 WCDMA B4 WCDMA B5 LTE B2 LTE B4 LTE B5 LTE B7 LTE B12 LTE B13 LTE B25 LTE B26_1 LTE B26_2 LTE B38 LTE B41 Frequency (MHz) 2402 2402 2412 824.2 1850.2 1852.4 1712.4 826.4 1850.7 1711 824.7 2502.5 699.7 779.5 1850.7 814.7 824.7 2572.5 2498.5 Conducted Output Power (dBm) 3.00 1.00 20.00 26.00 23.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 Tune Up Tolerance (dB) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 Output Power (W) 0.002 0.001 0.100 0.398 0.200 0.316 0.316 0.316 0.316 0.316 0.316 0.316 0.316 0.316 0.316 0.316 0.316 0.316 0.316 Antenna Gain (dBi) 8.00 8.00 12.00 2.00 4.00 4.00 4.00 4.00 4.00 4.00 2.00 3.10 3.20 3.20 4.00 2.00 2.00 3.10 3.10 Antenna Gain (Numeric) 6.31 6.31 15.85 1.58 2.51 2.51 2.51 2.51 2.51 2.51 1.58 2.04 2.09 2.09 2.51 1.58 1.58 2.04 2.04 Prediction Distance (cm) 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 Σ of MPE Time Averaged Duty Cycle (%) 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 ratios Calculated Power Density (W/m2) 0.025 0.016 3.153 1.255 0.997 1.580 1.580 1.580 1.580 1.580 0.997 1.284 1.314 1.314 1.580 0.997 0.997 1.284 1.284 Requirement (W/m2) 10.00 10.00 10.00 5.50 10.00 10.00 10.00 5.51 10.00 10.00 5.50 10.00 4.67 5.20 10.00 5.43 5.50 10.00 10.00 MPE ratio (PD/Req.) 0.003 0.002 0.315 0.228 0.100 0.158 0.158 0.287 0.158 0.158 0.181 0.128 0.282 0.253 0.158 0.184 0.181 0.128 0.128 Configuration 1 (MPE Ratio) 0.003 0.002 0.228 0.100 0.158 0.158 0.287 0.158 0.158 0.181 0.128 0.282 0.253 0.158 0.184 0.181 0.128 0.128 0.284 Configuration 2 (MPE Ratio) 0.315 0.228 0.100 0.158 0.158 0.287 0.158 0.158 0.181 0.128 0.282 0.253 0.158 0.184 0.181 0.128 0.128 0.597 Requirement: Σ of MPE ratios ≤ 1 The maximum values for GSM/WCDMA/LTE and BT/BLE/WiFi is used in the above calculations.Antenna GainFrequency (MHz) 2402 2402 2412 824.2 1850.2 1852.4 1712.4 826.4 1850.7 1711 824.7 2502.5 699.7 779.5 1850.7 814.7 824.7 2572.5 2498.5 2J4A50PCFa, Peak Gain (dBi) 3.7 3.7 3.7 2.0 4.0 4.0 4.0 4.0 4.0 4.0 2.0 3.1 2.0 2.0 4.0 2.0 2.0 3.1 3.1 2J4A50PCFa, Peak Gain, MIMO (dBi) 6.7 Volvo Base_Ant VT Full_Feat (dBi) 8.0 8.0 8.0 2.0 3.1 3.1 3.1 2.0 3.1 3.1 2.0 1.6 3.2 3.2 3.1 2.0 2.0 1.6 1.6 Volvo WLAN Interior (dBi) 4.0 Hirschman Interior Phone PK 1.6 0.6 0.6 0.6 1.6 0.6 0.6 1.6 -0.1 0.7 0.7 0.6 1.6 1.6 -0.1 -0.1 The Antennas Volvo Base VT and WLAN Interior are used at the same time, however they will normally be mounted so that they are separated by more than the prediction distance.

Datasheet 12.12.20191-4 ANTENNA WLAN INTERIOR Pt no. 23311706 / 920 638-001 ANTENNA INTERIOR WLAN Subject to alterations • Passive transmitting and reception antennas for BT/WLAN(2.4/5 GHz) • Low body height max. 5 mm • Coverage of frequency band BT/WLAN(2.4/5 GHz) • Mounting on plastic and glass materials Technical data* ParameterTR referenceRemarksUnitsValues Dimensions / Package35x45x5 mm Housing Protection ClassREQ 22379848-6 v1 REQ 22379848-8 v1 ISO20653IK 5k2 Operating TemperatureREQ 22379848-9 v1-40- +85°C Storage Temperature-40- +85°C Cable typeREQ 22379848-41 v1Dacar 302dB/m< 0.7 @ 2.5GHz < 1.2 @ 6GHz WLAN ParameterTR referenceFrequency rangesUnitsValues Frequency bandsREQ 22379848-53 v12400 ≤ f ≤ 2485 MHz 5150 ≤ f ≤ 5925 MHz Return LossREQ 22379848-54 v12400 – 2485 MHz 5150 - 5925 MHz typ. dB≥ 8 PolarizationREQ 22379848-60 v1VP (antenna mounted vertically)linear 12.12.20192-4 Datasheet ANTENNA WLAN INTERIOR Pt no. 23311706 / 920 638-001 Technical drawings Technical data* ParameterTR referenceRemarksUnitsValues Antenna Gain (Average)REQ 22379848-55 v12400 – 2485 MHz 5150 - 5925 MHz typ. dBi≥ -1.5 ≥ 0,5 ImpedanceREQ 22379848-54 v1 Ω 50 Diagnosis ResistorREQ 22379848-67 v1kΩ51 Power HandlingREQ 22379848-48 v1dBm≥ 30 * All technical requirements are according to 22379848.06 “Antenna System P2593/P2594 Multifunctional & Single function antennas” 12.12.20193-4 Datasheet ANTENNA WLAN INTERIOR Pt no. 23311706 / 920 638-001 Antenna diagrams Gain Radiation pattern 12.12.20194-4 Datasheet ANTENNA WLAN INTERIOR Pt no. 23311706 / 920 638-001 Subject to alterations Antenna diagrams Radiation pattern 12.12.20195-4 Datasheet ANTENNA WLAN INTERIOR Pt no. 23311706 / 920 638-001 Antenna diagrams Return loss ServiceLower LimitUpper Limit WLAN 2,42400 MHz2485 MHz WLAN 55150 MHz5925 MHz Frequency Table

Datasheet 21.03.20181-5 ANTENNA PHONE-PK INTERIOR Pt no. 23311714 / 920 453-003 ANTENNA INTERIOR PHONE-PK • Passive transmitting and reception antennas for the Cellular phone services 2G/3G/4G • Low body height max. 5 mm • Coverage of frequency bands LTE low (USA+EU), GSM850/900/1800/1900, UMTS, LTE high • Mounting on plastic and glass materials Subject to alterations Technical data* ParameterTR referenceRemarksUnitsValues Package107x54x5 mm Housing MaterialsREQ 22379848-23 v1TPU Elastollan® Konz 917/1, black Housing Protection ClassREQ 22379848-7 v1 REQ 22379848-7 v1 ISO 20653IP 5k2 Operating TemperatureREQ 22379848-9 v1-40- +85°C Storage Temperature-40- +85°C Cable typeREQ 22379848-41 v1RG 174< 1 @ 1GHz < 1.6 @ 2GHz < 2 @ 2.7GHz GSM/3G/4G ParameterTR referenceFrequency rangesUnitsValues Frequency bandsREQ 22379848-53 v1698 ≤ f ≤ 803 MHz 824 ≤ f ≤ 960 MHz 1710 ≤ f ≤ 2170 MHz 2300 ≤ f ≤ 2690 MHz dB±0,5 Return LossREQ 22379848-54 v1699 – 803 MHz 824 – 894 MH 880 – 960 MHz 1710 – 2170 MHz 2300 – 2690 MHz typ. dB7. 3 10 9.8 8.0 8.9 PolarizationREQ 22379848-60 v1linear 21.03.20182-5 Datasheet ANTENNA PHONE-PK INTERIOR Pt no. 23311714 / 920 453-003 Technical drawings Technical data* ParameterTR referenceFrequency rangesUnitsValues Antenna Gain (Average)REQ 22379848-55 v1699 – 803 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 2170 MHz 2300 – 2690 MHz typ. dBi0.7 1.6 1.6 0.6 -0.1 ImpedanceREQ 22379848-54 v1 Ω 50 Diagnosis ResistorREQ 22379848-67 v1kΩ51 Power HandlingREQ 22379848-48 v1W5 * All technical requirements are according to 22379848.06 “Antenna System P2593/P2594 Multifunctional & Single function antennas” 21.03.20183-5 Datasheet ANTENNA PHONE-PK INTERIOR Pt no. 23311714 / 920 453-003 Antenna diagrams Gain 21.03.20184-5 Datasheet ANTENNA PHONE-PK INTERIOR Pt no. 23311714 / 920 453-003 Antenna diagrams Radiation pattern 21.03.20185-5 Datasheet ANTENNA PHONE-PK INTERIOR Pt no. 23311714 / 920 453-003 Antenna diagrams Return loss Frequency Table ServiceLower LimitUpper Limit LT E699 MHz803 MHz AMPS+GSM900824 MHz960 MHz GSM1800+UMTS1710 MHz2170 MHz LT E2300 MHz2690 MHz Confection Datasheet is valid also for logisticaly handled package conditions 23311714 / 920 453-503 Single package replacement

05.09.20191-17 ANTENNA BASE_ANT RT FULL FEAT. Subject to alterations Pt no. Datasheet ANTENNA BASE FULL FEAT. 23311779/920 447-011 Pt no. ANTENNA BASE_ANT VT FULL FEAT. • Vehicle roof antenna for combined AM/FM/DAB and GNSS reception with integrated LNA • Transmission operation in the CELLULAR and WLAN services LTE low and high, GSM 850/900/1800/1890/UMTS and WLAN 2,4 GHz plus 5 GHz • Antenna rod 405 and 200 mm for AM/FM/DAB with M6 thread • Mounting on metallic vehicle roof from outside System overview ANTENNA AM/FM/DAB-ROD, 200 mm 230 371 07 825 180-001 ANTENNA AM/FM/DAB-ROD, 400 mm 224 729 86 825 066-001 22472983/920 447-012 FAKRA male Code B white FAKRA male Code C blue FAKRA male Code D bordeaux FAKRA male Code I beige 05.09.20192-17 Datasheet ANTENNA BASE_ANT VT FULL FEAT. ANTENNA BASE_ANT RT FULL FEAT. Pt no. Pt no. 23311779/920 447-011 22472983/920 447-012 Technische Daten / Technical data* ParameterTR referenceRemarksUnitsValues Dimensions / Package142 mm x 69 mm x 85 mm w/o rod Housing protection classREQ 22379848-6 v1 REQ 22379848-7 v1 ISO 20653IP 6k9k Housing materialREQ 22379848-23 v1PA6 Wellamid 6000, UV stabilized, thundergray Mounting materialmetal sheetmm0,75 - 1,2mm Operating temperature REQ 22379848-9 v1°C-40 – +85 °C Storage temperature°C-40 – +85 °C Antenna Isolation GSM to AM/FM/DAB (wo. Filter at AM/FM/DAB amplifier input) REQ 22379848-61 v187 – 108 MHz 174 – 240 MHz 699 – 960 MHz dB> 30 > 22 > 7 Antenna Isolation GSM to WLANREQ 22379848-61 v1699 – 960 MHz 1710 – 2690 MHz dB> 26 > 17 Antenna Isolation GSM to GNSSREQ 22379848-61 v1699 - 960 MHz 1559 – 1615 MHz 1710 – 2690 MHz dB> 32 > 15 > 23 Antenna Isolation WLAN to GNSS (wo. Filter at LNA input) REQ 22379848-61 v11559 – 1615 MHz 2400 – 2500 MHz dB> 14 > 8 AM/FM/DAB Amplifier ParameterTR referenceFrequency rangesUnitsValues PolarizationREQ 22379848-60 v1vertical Average antenna gainREQ 22379848-55 v1AM-LF 405 mm rod 200 mm rod AM-MF 405 mm rod 200 mm rod FM 405 mm rod 200 mm rod DAB 405 mm rod 200 mm rod dB ref 2,7 -4,7 3,3 -3,7 9,4 5,5 16,6 15,0 Frequency BandsREQ 22379848-53 v1AM 0.1485 ≤ f ≤ 1.705 MHz FM 76 ≤ f ≤ 108 MHz DAB(BandIII) ) 174 ≤ f ≤ 240 MHz dB±0,5 Impedance (Output)REQ 22379848-54 v1 Ω 50 Return loss (Output)REQ 22379848-54 v1Band ll (FM RoW) Band lll dB> 10 > 10 ∆IM3 P out = 110 dBμV REQ 22379848-58 v1LF f=(300 ±50) kHz MF f=(1000 ±50) kHz dB49 56 05.09.20193-17 Datasheet ANTENNA BASE_ANT VT FULL FEAT. ANTENNA BASE_ANT RT FULL FEAT. Pt no. Pt no. 23311779/920 447-011 22472983/920 447-012 Technische Daten / Technical data* ParameterTR referenceFrequency rangesUnitsValues ∆IM3 P out = 110 dBμV REQ 22379848-58 v1Band ll f=(98 ±0.5) MHzdB60 ∆IM3 P out = 110 dBμV REQ 22379848-58 v1Band lll f=(207 ±0.5) MHzdB61 AM Voltage gain (S 21 ) 50 Ω resistor connected to ground at the input REQ 22379848-56 v1LF MF dB5 ±2 5,7 ±2 FM Gain (S 21 Band ll / FM RoW)REQ 22379848-56 v1dB10 ±2 DAB Gain (S 21 Band lll)REQ 22379848-56 v1dB21 -3/+2 Noise Voltage (Output) (Detector average, Bandwidth 9 kHz, open input) REQ 22379848-63 v1LF MF dBμV-10 -11 Noise figure Band ll / FM RoWREQ 22379848-63 v1dB4,8 Noise Figure Band lllREQ 22379848-63 v1dB1,9 Supply voltageREQ 22379848-47 v1V12 -4/+2 Supply currentREQ 22379848-48 v1mA140 -5/+4 Power Supply MethodREQ 22379848-48 v1Phantom feed with internal voltage regulator in antenna GNSS Frequency bandsREQ 22379848-53 v1GNSS (GLONASS, GPS, Galilleo, BeiDou) 1559 MHz ≤ f ≤ 1606 MHz dB±0,5 PolarizationREQ 22379848-60 v1RHCP Average antenna gain GNSSREQ 22379848-55 v1passive, zenith θ=0°dBic2,7 Noise figureREQ 22379848-63 v1dB2,1 Gain (Filter+LNA) S 21 REQ 22379848-56 v1dB28 Out of band ∆IM3REQ 22379848-58 v1f1 = 1712,7 MHz f2 = 1850 MHz dB> 55 Band Pass Filter RejectionREQ 22379848-62 v150 ≤ |∆f| ≤ 70: 30 dBc 70 < |∆f| ≤ 100: 35 dBc |∆f| > 100: 40 dBc dB> 30 > 40 > 50 Impedance OutputREQ 22379848-54 v1 Ω 50 Return loss (Output)REQ 22379848-54 v1dB> 10 05.09.20194-17 Datasheet ANTENNA BASE_ANT VT FULL FEAT. ANTENNA BASE_ANT RT FULL FEAT. Pt no. 23311779/920 447-011 22472983/920 447-012 Ord. code Technische Daten / Technical data* ParameterTR referenceFrequency rangesUnitsValues Current consumptionREQ 22379848-48 v1mA27 -5/+3 Supply voltageREQ 22379848-47 v1V3,15-5,25 2G/3G/4G (CELLULAR) Frequency bandsREQ 22379848-53 v1698 ≤ f ≤ 803 MHz 824 ≤ f ≤ 960 MHz 1710 ≤ f ≤ 2170 MHz 2300 ≤ f ≤ 2690 MHz dB±0,5 PolarizationREQ 22379848-60 v1vertical Return lossREQ 22379848-54 v1699-803 MHz 824-894 MHz 880-960 MHz 1710-2170 MHz 2300-2690 MHz typ. dB7, 3 10 9,8 8,0 8,9 ImpedanceREQ 22379848-54 v1 Ω 50 Antenna gain (Average)REQ 22379848-55 v1699-803 MHz 824-894 MHz 880-960 MHz 1710-2170 MHz 2300-2690 MHz typ. dBi 3,2 2,0 2,0 3,1 1,6 Diagnosis ResistorREQ 22379848-67 v1kΩ51 Power HandlingREQ 22379848-48 v1698-803 MHz 824-894 MHz 880-960 MHz 1710-2170 MHz 2300-2690 MHz dBm37 WLAN Frequency bandsREQ 22379848-53 v1 (2.4GHz) 2400 ≤ f ≤ 2485 MHz (5GHz) 5150 ≤ f ≤ 5925 MHz dB±0,5 PolarizationREQ 22379848-60 v1vertical Return lossREQ 22379848-54 v12400-2485 MHz typ. dB10 ImpedanceREQ 22379848-54 v1 Ω 50 Antenna gain (Average)REQ 22379848-55 v12400-2485 MHztyp. dB10 Diagnosis resistorREQ 22379848-67 v1kΩ51 Power handlingREQ 22379848-48 v12.4GHz/5GHzdBm30 * All technical requirements are according to 22379848.06 “Antenna System P2593/P2594 Multifunctional & Single function antennas” 05.09.20195-17 Datasheet ANTENNA BASE_ANT VT FULL FEAT. ANTENNA BASE_ANT RT FULL FEAT. Pt no. 23311779/920 447-011 22472983/920 447-012 Technical drawings 05.09.20196-17 Datasheet ANTENNA BASE_ANT VT FULL FEAT. ANTENNA BASE_ANT RT FULL FEAT. Pt no. Pt no. 23311779/920 447-011 22472983/920 447-012 Antenna diagrams AM/FM Gain (active w. 405 mm …

Text truncated - open the document above for the full version.