AUO-LABQ3LabQuest 3

ƒ„—‡•– ̺ ͵Ȃ•‡”ƒ—ƒŽ Version 3.0.0 August 2020 LabQuest ® 3 – User Manual ii ABOUT THIS GUIDE LabQuest 3, released in August 2020, ships with a Quick-Start Guide to get you started with basic data collection and analysis. The LabQuest 3 User Manual is an extended guide detailing the hardware and software features of LabQuest 3. LabQuest ® 3 User Manual iii SAFETY INFORMATION Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation RF Exposure Warning The equipment complies with RF exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. LabQuest ® 3 – User Manual iv IC Statement 7KLVGHYLFHFRQWDLQVOLFHQFHH[HPSWWUDQVPLWWHU V UHFHLYHU V WKDWFRPSO\ZLWK,QQRYDWLRQ 6FLHQFHDQG(FRQRPLF'HYHORSPHQW&DQDGD¶VOLFHQFHH[HPSW566 V 2SHUDWLRQLVVXEMHFWWR WKHIROORZLQJWZRFRQGLWLRQV  7KLVGHYLFHPD\QRWFDXVHLQWHUIHUHQFH  7KLVGHYLFHPXVWDFFHSWDQ\LQWHUIHUHQFHLQFOXGLQJLQWHUIHUHQFHWKDWPD\FDXVHXQGHVLUHG RSHUDWLRQRIWKHGHYLFH Industry Canada - Class B This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. RF exposure warning: The equipment complies with RF exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. /¶pPHWWHXUUpFHSWHXUH[HPSWGHOLFHQFHFRQWHQXGDQVOHSUpVHQWDSSDUHLOHVWFRQIRUPHDX[&15 G¶,QQRYDWLRQ6FLHQFHVHW'pYHORSSHPHQWpFRQRPLTXH&DQDGDDSSOLFDEOHVDX[DSSDUHLOVUDGLR H[HPSWVGHOLFHQFH/¶H[SORLWDWLRQHVWDXWRULVpHDX[GHX[FRQGLWLRQVVXLYDQWHV  /¶DSSDUHLOQHGRLWSDVSURGXLUHGHEURXLOODJH  /¶DSSDUHLOGRLWDFFHSWHUWRXWEURXLOODJHUDGLRpOHFWULTXHVXELPrPHVLOHEURXLOODJHHVW VXVFHSWLEOHG¶HQFRPSURPHWWUHOHIRQFWLRQQHPHQW Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme sur le matériel interférant-brouilleur: “Appareils Numériques,” NMB-003 édictée par industrie Canada. L’utilisation est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer d’interférences, et (2) cet appareil doit accepter toutes interférences, y comprises celles susceptibles de provoquer un disfonctionnement du dispositif. Afin de réduire les interférences radio potentielles pour les autres utilisateurs, le type d’antenne et son gain doivent être choisie de telle façon que l’équivalent de puissance isotrope émis (e.i.r.p) n’est pas plus grand que celui permis pour une communication établie. Avertissement d’exposition RF: L’équipement est conforme aux limites d’exposition aux RF établies pour un environnement non supervisé. L’antenne (s) utilisée pour ce transmetteur ne doit pas être jumelés ou fonctionner en conjonction avec toute autre antenne ou transmetteur. LabQuest ® 3 User Manual v CONTENTS I. GETTING STARTED WITH LABQUEST ® 3 ........................................................................................ 1 What’s Included..................................................................................................................1 Preparing for First Time Use ..............................................................................................1 Powering on LabQuest .......................................................................................................1 Using the Touch Screen......................................................................................................2 Device Navigation ..............................................................................................................3 Customizing the Settings ....................................................................................................4 Connecting Sensors .…

Text truncated - open the document above for the full version.

Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 1 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 2 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 3 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 4 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 5 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 30 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 AC Adapter Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 31 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 32 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 33 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 34 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 35 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 36 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 ─────THE END────

Label Location Information EUT (Back View) Label Location

Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 6 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 7 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 8 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 9 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 10 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 11 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 12 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 13 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 14 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 15 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 16 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 17 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 18 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 19 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 20 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 21 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 22 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 23 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 24 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 25 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 26 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 27 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 28 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 29 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020 Photographs of EUT Report No. : EP081907 SPORTON International Inc. Page No. : 30 of 36 TEL : 886-3-327-3456 EP Report Version : Rev. 01 FAX : 886-3-327-0973 Issued Date : Oct. 28, 2020

FCC ID: AUO-LABQ3 Page: 1 / 36 Report No.: T200916W01-SF Rev.: 01 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group FCC TEST REPORT FCC 47 CFR § 2.1093 IEEE Std 1528-2013 for LabQuest 3 with 802.11 b/g/n,BT/BLE Model Name: LABQ3 Issued to: Vernier Software & Technology LLC 13979 SW Millikan Way Beaverton, OR 97005-2886, U.S.A Issued by Compliance Certification Services Inc. Wugu Lab. No.11, Wugong 6th Rd., Wugu Dist., New Taipei City, Taiwan. (R.O.C.) Issued Date: 10/19/2020 Statements of Conformity Determination of compliance is based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. Note: This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, A2LA, NIST or any government agencies. The test results in the report only apply to the tested sample. Page: 2 / 36 Report No.: T200916W01-SF Rev.: 01 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 09/22/2020 Initial Issue ALL Sky 01 10/19/2020 Change the FCC ID. Page 1 Sky Page: 3 / 36 Report No.: T200916W01-SF Rev.: 01 Table of Contents 1 CERTIFICATE OF COMPLIANCE (SAR EVALUATION)..................................................... 5 2 DESCRIPTION OF EQUIPMENT UNDER TEST ............................................................... 6 2.1 SUMMARY OF HIGHEST SAR VALUES .............................................................................................................. 7 3 REQUIREMENTS FOR COMPLIANCE TESTING DEFINED ............................................... 8 3.1 REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE FCC .......................................................... 8 4 DOSIMETRIC ASSESSMENT SYSTEM .......................................................................... 9 4.1 MEASUREMENT SYSTEM DIAGRAM .............................................................................................................. 10 4.2 SYSTEM COMPONENTS ................................................................................................................................... 11 5 EVALUATION PROCEDURES .................................................................................... 14 6 SAR MEASUREMENT PROCEDURES ......................................................................... 16 6.1 NORMAL SAR TEST PROCEDURE .................................................................................................................... 16 7 MEASUREMENT UNCERTAINTY .............................................................................. 18 8 ANTENNA LOCATION ............................................................................................. 19 9 RF EXPOSURE CONDITIONS (TEST CONFIGURATIONS) .............................................. 20 9.1. STANDALONE SAR TEST EXCLUSION CONSIDERATIONS .......................................................................... 20 9.2. REQUIRED TEST CONFIGURATIONS .............................................................................................................. 20 10 EXPOSURE LIMIT ................................................................................................... 21 11 TISSUE DIELECTRIC PROPERTIES ............................................................................. 22 11.1 TEST LIQUID CONFIRMATION ......................................................................................................................... 22 11.2 TYPICAL COMPOSITION OF INGREDIENTS FOR LIQUID TISSUE PHANTOMS........................................... 23 11.3 SIMULATING LIQUIDS PARAMETER CHECK RESULTS .................................................................................. 24 12 SYSTEM PERFORMANCE CHECK .............................................................................. 25 12.1 SYSTEM PERFORMANCE CHECK RESULTS .................................................................................................... 26 13 RF OUTPUT POWER MEASUREMENT ...................................................................... 27 13.1 WI-FI 2.4GHZ (DTS BAND) ............................................................................................................................... 28 13.2 BLUETOOTH ...................................................................................................................................................... 29 14 MEASURED AND RE…

Text truncated - open the document above for the full version.

Test Laboratory: CCS Taiwan.(R.O.C),Ltd. Wugu Laboratory. Date: 2020/9/17 System Performance Check-D2450V2 SN727 Frequency: 2450 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 23.0C; Liquid Temperature: 22.0C Medium parameters used: f = 2450 MHz; σ = 1.828 S/m; ε r = 38.191; ρ = 1000 kg/m 3 DASY5 Configuration: - Area Scan Setting: Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn856; Calibrated: 2020/4/23 - Probe: EX3DV4 - SN3665; ConvF(7.35, 7.35, 7.35) @ 2450 MHz; Calibrated: 2020/8/20 - Sensor-Surface: 2mm (Mechanical Surface Detection) - Phantom: ELI Head/Pin=250mW/Area Scan (71x91x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 21.4 W/kg Head/Pin=250mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 107.9 V/m; Power Drift = -0.10 dB Peak SAR (extrapolated) = 28.5 W/kg SAR(1 g) = 13.3 W/kg; SAR(10 g) = 6.01 W/kg Smallest distance from peaks to all points 3 dB below = 9 mm Ratio of SAR at M2 to SAR at M1 = 46.6% Maximum value of SAR (measured) = 20.6 W/kg 0 dB = 20.6 W/kg = 13.14 dBW/kg

Test Laboratory: CCS Taiwan.(R.O.C),Ltd. Wugu Laboratory. Date: 2020/9/17 WiFi 2.4GHz Frequency: 2437 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 23.2C; Liquid Temperature: 22.1C Medium parameters used: f = 2437 MHz; σ = 1.883 S/m; ε r = 39.943; ρ = 1000 kg/m 3 DASY5 Configuration: - Area Scan Setting: Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn856; Calibrated: 2020/4/23 - Probe: EX3DV4 - SN3665; ConvF(7.35, 7.35, 7.35) @ 2437 MHz; Calibrated: 2020/8/20 - Sensor-Surface: 2mm (Mechanical Surface Detection) - Phantom: ELI Edge 3/802.11b 1M_CH 6_0mm/Area Scan (61x141x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.276 W/kg Edge 3/802.11b 1M_CH 6_0mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 3.268 V/m; Power Drift = 0.18 dB Peak SAR (extrapolated) = 0.421 W/kg SAR(1 g) = 0.162 W/kg; SAR(10 g) = 0.064 W/kg Smallest distance from peaks to all points 3 dB below = 6 mm Ratio of SAR at M2 to SAR at M1 = 41.5% Maximum value of SAR (measured) = 0.278 W/kg 0 dB = 0.278 W/kg = -5.56 dBW/kg Test Laboratory: CCS Taiwan.(R.O.C),Ltd. Wugu Laboratory. Date: 2020/9/17 Bluetooth Frequency: 2441 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 23.1C; Liquid Temperature: 22.1C Medium parameters used: f = 2441 MHz; σ = 1.888 S/m; ε r = 39.904; ρ = 1000 kg/m 3 DASY5 Configuration: - Area Scan Setting: Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn856; Calibrated: 2020/4/23 - Probe: EX3DV4 - SN3665; ConvF(7.35, 7.35, 7.35) @ 2441 MHz; Calibrated: 2020/8/20 - Sensor-Surface: 2mm (Mechanical Surface Detection) - Phantom: ELI Edg3/GFSK_CH 39_0mm/Area Scan (61x141x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.184 W/kg Edg3/GFSK_CH 39_0mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 2.489 V/m; Power Drift = -0.09 dB Peak SAR (extrapolated) = 0.304 W/kg SAR(1 g) = 0.117 W/kg; SAR(10 g) = 0.046 W/kg Smallest distance from peaks to all points 3 dB below = 6 mm Ratio of SAR at M2 to SAR at M1 = 39.6% Maximum value of SAR (measured) = 0.200 W/kg 0 dB = 0.200 W/kg = -6.99 dBW/kg

FCC Test Report Report No. :FR081907AC TEL : 886-3-3273456 Page Number : 1 of 25 FAX : 886-3-3270973 Issued Date : Oct. 28, 2020 Report Template No.: HE1-C8 Ver3.9 Report Version : 01 FCC ID: AUO-LABQ3 FCC Test Report FCC ID : AUO-LABQ3 Equipment : LabQuest 3 Brand Name : Vernier Model Name : LABQ3 Applicant : Vernier Software & Technology 13979 SW Millikan Way Beaverton, OR 97005, USA Manufacturer : Vernier Software & Technology 13979 SW Millikan Way Beaverton, OR 97005, USA Standard : 47 CFR FCC Part 15.247 The product was received on Aug. 19, 2020, and testing was started from Aug. 26, 2020 and completed on Sep. 15, 2020. We, SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory, would like to declare that the tested sample has been evaluated in accordance with the procedures given in ANSI C63.10-2013 and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory, the test report shall not be reproduced except in full. ___________________________________________ Approved by: Allen Lin SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City, Taiwan (R.O.C.) FCC Test Report Report No. :FR081907AC TEL : 886-3-3273456 Page Number : 2 of 25 FAX : 886-3-3270973 Issued Date : Oct. 28, 2020 Report Template No.: HE1-C8 Ver3.9 Report Version : 01 FCC ID: AUO-LABQ3 Table of Contents HISTORY OF THIS TEST REPORT .................................................................................................................. 3 SUMMARY OF TEST RESULT ......................................................................................................................... 4 1 GENERAL DESCRIPTION .................................................................................................................... 5 1.1 Information .............................................................................................................................................. 5 1.2 Testing Applied Standards ..................................................................................................................... 7 1.3 Testing Location Information .................................................................................................................. 7 1.4 Measurement Uncertainty ...................................................................................................................... 7 2 TEST CONFIGURATION OF EUT......................................................................................................... 8 2.1 Test Condition ........................................................................................................................................ 8 2.2 Test Channel Mode ................................................................................................................................ 8 2.3 The Worst Case Measurement Configuration ........................................................................................ 9 2.4 Accessories .......................................................................................................................................... 10 2.5 Support Equipment ............................................................................................................................... 10 2.6 Test Setup Diagram ............................................................................................................................. 11 3 TRANSMITTER TEST RESULT .......................................................................................................... 13 3.1 AC Power-line Conducted Emissions .................................................................................................. 13 3.2 DTS Bandwidth..................................................................................................................................... 15 3.3 Maximum Conducted Output Power .................................................................................................... 16 3.4 Power Spectral Density ........................................................................................................................ 18 3.5 Emissions in Non-restricted Frequency Bands .................................................................................... 19 3.6 Emissions in Restricted Frequency Bands ........................................................................................... 20 4 TEST EQUIPMENT AND CALIBRATION DATA ................................................................................ 24 APPENDIX A. TEST RESULTS OF AC POWER-LINE CONDUCTED EMISSIONS APPENDIX B. TEST RESULTS OF DTS BANDWIDTH APPENDIX C. TEST RESULTS OF MAXIMUM CONDUCTED OUTPUT POWER APPENDIX D. TEST RESULTS OF POWER SPECTRAL DENSITY APPENDIX E. TEST RESULTS OF EMISSIONS IN NON-RESTRICTED FREQUENCY BANDS APPENDIX F. TEST RESULTS OF EMISSIONS IN RESTRICTED FREQUENCY BANDS APPENDIX G. TEST PHOTOS PHOTOGRAPHS OF EUT V01 FCC Test Report Report No. :FR081907AC TEL : 886-3-3273456 Page Number : 3 of 25 FAX : 886-3-3270973 Issued Date : Oct. 28, 2020 Report Template No.: HE1-C8 Ver3.9 Report Version : 01 FCC ID: AUO-LABQ3 History of this test report Report No. Version Description Issued Date FR081907AC 01 Initial issue of report Oct. 28, 2020 FCC Test Report Report No. :FR081907AC TEL : 886-3-3273456 Page Number : 4 of 25 FAX : 886-3-3270973 Issued Date : Oct. 28, 2020 Report Template No.: HE1-C8 Ver3.9 Report Version : 01 FCC ID: AUO-LABQ3 Summary of Test Result Report Clause Ref. Std. Clause Test Items Result (PASS/FAIL) Remark 1.1.2 15.203 Antenna Requirement PASS - 3.1 15.207 AC Power-line Conducted Emissions PASS - 3.2 15.247(a) DTS Bandwidth PASS - 3.3 15.247(b) Maximum Conducted Output Power PASS - 3.4 15.247(e) Power Spectral Density PASS - 3.5 1…

Text truncated - open the document above for the full version.

FCC Test Report Report No. : FR081907AL TEL : 886-3-3273456 Page Number : 1 of 26 FAX : 886-3-3270973 Issued Date : Oct. 28, 2020 Report Template No.: HE1-C10 Ver3.9 Report Version : 01 FCC ID: AUO-LABQ3 FCC Test Report FCC ID : AUO-LABQ3 Equipment : LabQuest 3 Brand Name : Vernier Model Name : LABQ3 Applicant : Vernier Software & Technology 13979 SW Millikan Way Beaverton, OR 97005, USA Manufacturer : Vernier Software & Technology 13979 SW Millikan Way Beaverton, OR 97005, USA Standard : 47 CFR FCC Part 15.247 The product was received on Aug. 19, 2020, and testing was started from Aug. 26, 2020 and completed on Sep. 15, 2020. We, SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory, would like to declare that the tested sample has been evaluated in accordance with the procedures given in ANSI C63.10-2013 and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory, the test report shall not be reproduced except in full. ___________________________________________ Approved by: Allen Lin __________________________________________ SDoC by: XXXXX SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City, Taiwan (R.O.C.) FCC Test Report Report No. : FR081907AL TEL : 886-3-3273456 Page Number : 2 of 26 FAX : 886-3-3270973 Issued Date : Oct. 28, 2020 Report Template No.: HE1-C10 Ver3.9 Report Version : 01 FCC ID: AUO-LABQ3 Table of Contents HISTORY OF…

Text truncated - open the document above for the full version.