AUO-LQ2-LELabQuest2

2 Reference Guide v1.01 ©Vernier Software & Technology LabQuest 2 Reference Guide i SAFETY INFORMATION Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation RF Exposure Warning The equipment complies with RF exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. IC Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Industry Canada - Class B This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. LabQuest 2 Reference Guide ii RF exposure warning: The equipment complies with RF exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’appareil doit accepter tout interférence radioélectrique, même si cela résulte à un brouillage susceptible d’en compromettre le fonctionnement. Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme sur le matériel interférant-brouilleur: “Appareils Numériques,” NMB-003 édictée par industrie Canada. L’utilisation est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer d’interférences, et (2) cet appareil doit accepter toutes interférences, y comprises celles susceptibles de provoquer un disfonctionnement du dispositif. Afin de réduire les interférences radio potentielles pour les autres utilisateurs, le type d’antenne et son gain doivent être choisie de telle façon que l’équivalent de puissance isotrope émis (e.i.r.p) n’est pas plus grand que celui permis pour une communication établie. Avertissement d’exposition RF: L’équipement est conforme aux limites d’exposition aux RF établies pour un environnement non supervisé. L’antenne (s) utilisée pour ce transmetteur ne doit pas être jumelés ou fonctionner en conjonction avec toute autre antenne ou transmetteur. ABOUT THIS GUIDE LabQuest 2, released in March 2012, ships with a Quick-Start Guide intended to get you up and running with basic data collection and analysis. The LabQuest 2 Reference Guide is an extended guide designed as a comprehensive resource detailing the features, hardware, and software of LabQuest 2. LabQuest 2 Reference Guide iii CONTENTS I. GETTING STARTED WITH LABQUEST 2 ......................................................................................... 1 What’s Included .................................................................................................................1 Using LabQuest 2 for the First Time ..................................................................................1 Quick Start to Data Collection ...........................................................................................2 II. LABQUEST HARDWARE .................................................................................................................... 4 Power Button ......................................................................................................................4 Touch Screen ......................................................................................................................5 Hardware Keys ..............................................................................................................…

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 2.0 775 Montague Expressway, Milpitas, CA 95035 USA Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (current) 1.0 1.0 Nov-14-2006 Revised wording (current) 1.0 2.0 Sept–25-2007 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 2.0 Vernier Software & Technology Date:2013/4/9 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, _____ Vernier Software & Technology____hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): (Product name: LabQuest2, model name: LQ2-LE) We affirm that between SIEMIC and __ Vernier Software & Technology___, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Client’s signature Name/Title: John Wheeler / Director of Engineering/Partner Company Name: Vernier Software & Technology Address: 13979 SW Millikan Way Beaverton, OR 97005 TEL: 503-277-2299 FAX: 503-277-2440 Email: [email protected]

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 2.0 775 Montague Expressway, Milpitas, CA 95035 USA Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (current) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 1.0 2.0 August – 11 - 2008 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 2.0 Vernier Software & Technology Date：2013/4/8 To: Federal Communications Commission 775 Montague Expressway, Milpitas, CA 95035 USA Subject: Permanent Confidentiality Request for FCC ID: AUO-LQ2-LE We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Circuit Diagram - Operational Description - Antenna Spec The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature : Name/Title: John Wheeler / Director of Engineering/Partner Company Name: Vernier Software & Technology Address: 13979 SW Millikan Way Beaverton, OR 97005 TEL: 503-277-2299 FAX: 503-277-2440 Email: [email protected]

Compliance Certification Services Inc. Report No.: T130325W06 Date of Issue: April 15, 2013 A1 - 1 / 13 Rev. 00 APPENDIX 1 - PHOTOGRAPHS OF EUT EXTERNAL PHOTOGRAPHS OF EUT Compliance Certification Services Inc. Report No.: T130325W06 Date of Issue: April 15, 2013 A1 - 2 / 13 Rev. 00 Compliance Certification Services Inc. Report No.: T130325W06 Date of Issue: April 15, 2013 A1 - 3 / 13 Rev. 00 Compliance Certification Services Inc. Report No.: T130325W06 Date of Issue: April 15, 2013 A1 - 4 / 13 Rev. 00 Compliance Certification Services Inc. Report No.: T130325W06 Date of Issue: April 15, 2013 A1 - 5 / 13 Rev. 00 Compliance Certification Services Inc. Report No.: T130325W06 Date of Issue: April 15, 2013 A1 - 6 / 13 Rev. 00

Compliance Certification Services Inc. Report No.: T130325W06 Date of Issue: April 15, 2013 A1 - 7 Rev. 00 INTERNAL PHOTOGRAPHS OF EUT Compliance Certification Services Inc. Report No.: T130325W06 Date of Issue: April 15, 2013 A1 - 8 Rev. 00 Compliance Certification Services Inc. Report No.: T130325W06 Date of Issue: April 15, 2013 A1 - 9 Rev. 00 Compliance Certification Services Inc. Report No.: T130325W06 Date of Issue: April 15, 2013 A1 - 10 Rev. 00 Compliance Certification Services Inc. Report No.: T130325W06 Date of Issue: April 15, 2013 A1 - 11 Rev. 00 GPS Antenna Compliance Certification Services Inc. Report No.: T130325W06 Date of Issue: April 15, 2013 A1 - 12 Rev. 00 WIFI & BT Antenna Compliance Certification Services Inc. Report No.: T130325W06 Date of Issue: April 15, 2013 A1 - 13 Rev. 00 GPS Module WIFI & BT Module

Compliance Certification Services Inc. FCC ID: AUO-LQ2-LE Report No: T130325W06-SF Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 Total Page: 31 Rev. 02 ANSI/IEEE Std. C95.1-1992 in accordance with the requirements of FCC Report and Order: ET Docket 93-62, and OET Bulletin 65 Supplement C FCC TEST REPORT For LabQuest2 Trade Name: Vernier Model: LQ2-LE Issued to Vernier Software & Technology 13979 SW Millikan Way Beaverton, OR 97005 Issued by Compliance Certification Services Inc. No.11, Wugong 6th Rd., Wugu Dist., New Taipei City 24891, Taiwan. (R.O.C.) http://www.ccsrf.com [email protected]. Issued Date: 2013/03/29 Compliance Certification Services Inc. FCC ID: AUO-LQ2-LE Report No: T130325W06-SF Page 2 Rev. 02 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 2013/03/29 Initial Issue ALL Scott Hsu 01 2013/04/16 Revise Bluetooth Band 26 Scott Hsu 02 2013/06/04 Add Device Under Test of new section 11. 23 Scott Hsu Compliance Certification Services Inc. FCC ID: AUO-LQ2-LE Report No: T130325W06-SF Page 3 Rev. 02 Table of contents 1 Certificate of Compliance (SAR Evaluation) ............................................................... 4 2 EUT Description ...................................................................................................... 5 3 Requirements for Compliance Testing Defined .......................................................... 6 3.1 Requirements for Compliance Testing Defined by the FCC ........................................................................ 6 4 Dosimetric Assessment System ................................................................................ 6 4.1 Measurement System Diagram ....................................................................................................................... 7 4.2 System Components .......................................................................................................................................... 8 5 Evaluation Procedures ........................................................................................... 11 6 Measurement Uncertainty ..................................................................................... 15 7 Exposure Limit ...................................................................................................... 16 8 Tissue Dielectric Properties .................................................................................... 17 8.1 Test Liquid Confirmation ................................................................................................................................. 17 8.2 Typical Composition of Ingredients for Liquid Tissue Phantoms .............................................................. 18 8.3 Simulating Liquids Parameter Check Results ............................................................................................... 19 9 System Performance Check .................................................................................... 20 9.1 System Performance Check Results .............................................................................................................. 21 10 Summary of Test Configurations ............................................................................ 22 10.1 Body Test Exclusion Thresholds ......................................................................................................... 22 10.2 Body Exposure Conditions for WiFi ................................................................................................... 22 10.3 Body Exposure Conditions for Bluetooth........................................................................................... 22 11 Device Under Test ................................................................................................. 23 11.1 Simultaneous Transmission ............................................................................................................... 23 12 RF Output Power Measurement ............................................................................. 24 12.1 WiFi (2.4 GHz Band) ........................................................................................................................... 24 12.2 Bluetooth ........................................................................................................................................... 25 13 SAR Measurements Results ................................................................................... 26 13.1 Summary of Highest SAR Values .................................................................................................................... 27 14 Antenna Locations & Separation Distances ............................................................. 28 15 Equipment List & Calibration Status ....................................................................... 29 16 Facilities ............................................................................................................... 30 17 Reference ............................................................................................................. 30 18 Attachments ......................................................................................................... 31 Compliance Certification Services Inc. FCC ID: AUO-LQ2-LE Report No: T130325W06-SF Page 4 Rev. 02 1 Certificate of Compliance (SAR Evaluation) Applicant Vernier Software & Technology 13979 SW Millikan Way Beaverton, OR 97005 Equipment Under Test: LabQuest2 Trade Name: Vernier Model Number: LQ2-LE Date of Test: March 29 , 2013 Device Category: PORTABLE DEVICES Exposure Category: GENERAL POPULATION/UNCONTROLLED EXPOSURE Applicable Standards FCC  FCC OET 65 Supplement C  IEEE 1528 2003  KDB 447498…

Text truncated - open the document above for the full version.

Test Laboratory: Compliance Certification Service Inc. SAR Lab 02 Date: 3/29/2013 20130329_System Check_Dipole2450V2 SN728 Frequency: 2450 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 24.0C; Liquid Temperature: 23.0C Medium parameters used (interpolated): f = 2450 MHz; σ = 1.96 mho/m; ε r = 50.7; ρ = 1000 kg/m 3 ; DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn558; Calibrated: 7/19/2012 - Probe: EX3DV4 - SN3554; ConvF(6.06, 6.06, 6.06); Calibrated: 9/27/2012 - Sensor-Surface: 2mm (Mechanical Surface Detection (Locations From Previous Scan Used))Sensor-Surface: 2mm (Mechanical Surface Detection) - Phantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN: 1052 Body/Pin=100mW, d=10mm/Area Scan (8x9x1): Measurement grid: dx=15mm, dy=15mm Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 4.84 mW/g Body/Pin=100mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 64.0 V/m; Power Drift = -0.043 dB Peak SAR (extrapolated) = 11.0 W/kg SAR(1 g) = 5.26 mW/g; SAR(10 g) = 2.45 mW/g Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 8.05 mW/g 0 dB = 8.05mW/g Test Laboratory: Compliance Certification Service Inc. SAR Lab 02 Date: 3/29/2013 20130329_System Check_Dipole2450V2 SN728 Frequency: 2450 MHz; Duty Cycle: 1:1 Body/Pin=100mW, d=10mm/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 7.98 mW/g Test Laboratory: Compliance Certification Service Inc. SAR Lab 02 Date: 3/29/2013 Bluetooth Band Frequency: 2441 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 24.0C; Liquid Temperature: 23.0C Medium parameters used (interpolated): f = 2441 MHz; σ = 1.94 mho/m; ε r = 50.7; ρ = 1000 kg/m 3 ; DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn558; Calibrated: 7/19/2012 - Probe: EX3DV4 - SN3554; ConvF(6.06, 6.06, 6.06); Calibrated: 9/27/2012 - Sensor-Surface: 2mm (Mechanical Surface Detection) - Phantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN: 1052 Front Touch/DH5/CH 39/Area Scan (7x7x1): Measurement grid: dx=15mm, dy=15mm Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 0.264 mW/g Front Touch/DH5/CH 39/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 9.84 V/m; Power Drift = 0.137 dB Peak SAR (extrapolated) = 0.594 W/kg SAR(1 g) = 0.324 mW/g; SAR(10 g) = 0.247 mW/g Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 0.408 mW/g Test Laboratory: Compliance Certification Service Inc. SAR Lab 02 Date: 3/29/2013 Bluetooth Band Frequency: 2441 MHz; Duty Cycle: 1:1 Front Touch/DH5/CH 39/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 0.176 mW/g Test Laboratory: Compliance Certification Service Inc. SAR Lab 02 Date: 3/29/2013 2450MHz Band Frequency: 2412 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 24.0C; Liquid Temperature: 23.0C Medium parameters used: f = 2412.7 MHz; σ = 1.9 mho/m; ε r = 50.8; ρ = 1000 kg/m 3 ; DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn558; Calibrated: 7/19/2012 - Probe: EX3DV4 - SN3554; ConvF(6.06, 6.06, 6.06); Calibrated: 9/27/2012 - Sensor-Surface: 2mm (Mechanical Surface Detection) - Phantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN: 1052 Edge1 Touch/802.11b/CH 1/Area Scan (6x9x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.194 mW/g Edge1 Touch/802.11b/CH 1/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 7.89 V/m; Power Drift = 0.048 dB Peak SAR (extrapolated) = 0.349 W/kg SAR(1 g) = 0.156 mW/g; SAR(10 g) = 0.083 mW/g Maximum value of SAR (measured) = 0.242 mW/g Test Laboratory: Compliance Certification Service Inc. SAR Lab 02 Date: 3/29/2013 2450MHz Band Frequency: 2412 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 24.0C; Liquid Temperature: 23.0C Medium parameters used: f = 2412.7 MHz; σ = 1.37 mho/m; ε r = 50.8; ρ = 1000 kg/m 3 ; DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn558; Calibrated: 7/19/2012 - Probe: EX3DV4 - SN3554; ConvF(6.06, 6.06, 6.06); Calibrated: 9/27/2012 - Sensor-Surface: 2mm (Mechanical Surface Detection) - Phantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN: 1052 Edge4 Touch/802.11b/CH 1/Area Scan (6x13x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 1.07 mW/g Edge4 Touch/802.11b/CH 1/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 15.0 V/m; Power Drift = 0.030 dB Peak SAR (extrapolated) = 1.93 W/kg SAR(1 g) = 0.723 mW/g; SAR(10 g) = 0.326 mW/g Maximum value of SAR (measured) = 1.21 mW/g Test Laboratory: Compliance Certification Service Inc. SAR Lab 02 Date: 3/29/2013 2450MHz Band Frequency: 2412 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 24.0C; Liquid Temperature: 23.0C Medium parameters used: f = 2412.7 MHz; σ = 1.9 mho/m; ε r = 50.8; ρ = 1000 kg/m 3 ; DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn558; Calibrated: 7/19/2012 - Probe: EX3DV4 - SN3554; ConvF(6.06, 6.06, 6.06); Calibrated: 9/27/2012 - Sensor-Surface: 2mm (Mechanical Surface Detection) - Phantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN: 1052 Rear Touch/802.11b/CH 1/Area Scan (7x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of …

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Reference No.: T120205G01-RP2 FCC ID: AUO-LQ2-LE Report No.: T130325W06-RP2 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 / 82 Rev.00 FCC 47 CFR PART 15 SUBPART C TEST REPORT For LabQuest2 Model: LQ2-LE Trade Name: Vernier Issued to Vernier Software & Technology 13979 SW Millikan Way Beaverton, OR 97005 Issued by Compliance Certification Services Inc. No.11, Wugong 6th Rd., Wugu Dist., New Taipei City 24891, Taiwan. (R.O.C.) http://www.ccsrf.com [email protected] Issued Date: April 15, 2013 Compliance Certification Services Inc. Reference No.: T120205G01-RP2 FCC ID: AUO-LQ2-LE Report No.: T130325W06-RP2 Page 2 Rev.00 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 February 16, 2012 Initial Issue ALL Sandy Lin 01 April 15, 2013 See the Following Note Rev.(01). ALL Rachel Wu Rev. (01): 1. Update pin to pin RF module. 2. Other information, please refer to the T120205G01 and this test report. Compliance Certification Services Inc. Reference No.: T120205G01-RP2 FCC ID: AUO-LQ2-LE Report No.: T130325W06-RP2 Page 3 Rev.00 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION.................................................................................................4 2. EUT DESCRIPTION ........................................................................................................................5 3. TEST METHODOLOGY .................................................................................................................6 3.1 EUT CONFIGURATION.....................................................................................................................6 3.2 EUT EXERCISE.................................................................................................................................6 3.3 GENERAL TEST PROCEDURES..........................................................................................................6 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS......................................................7 3.5 DESCRIPTION OF TEST MODES........................................................................................................8 4. INSTRUMENT CALIBRATION.....................................................................................................9 4.1 MEASURING INSTRUMENT CALIBRATION...................................................................................9 4.2 MEASUREMENT EQUIPMENT USED ......................................................................................9 4.3 MEASUREMENT UNCERTAINTY ..........................................................................................10 5. FACILITIES AND ACCREDITATIONS .....................................................................................11 5.1 FACILITIES ....................................................................................................................................11 5.2 EQUIPMENT...................................................................................................................................11 5.3 TABLE OF ACCREDITATIONS AND LISTINGS..................................................................................12 6. SETUP OF EQUIPMENT UNDER TEST ....................................................................................13 6.1 SETUP CONFIGURATION OF EUT....................................................................................................13 6.2 SUPPORT EQUIPMENT ............................................................................................................13 7. FCC PART 15.247 REQUIREMENTS..........................................................................................14 7.1 20 DB BANDWIDTH..................................................................................................................14 7.2 PEAK POWER.................................................................................................................................21 7.3 BAND EDGES MEASUREMENT .............................................................................................22 7.4 FREQUENCY SEPARATION ....................................................................................................40 7.5 NUMBER OF HOPPING FREQUENCY....................................................................................45 7.6 TIME OF OCCUPANCY (DWELL TIME) ................................................................................50 7.7 SPURIOUS EMISSIONS .............................................................................................................59 7.8 POWERLINE CONDUCTED EMISSIONS............................................................................................77 APPENDIX I PHOTOGRAPHS OF TEST SETUP............................................................................80 Compliance Certification Services Inc. Reference No.: T120205G01-RP2 FCC ID: AUO-LQ2-LE Report No.: T130325W06-RP2 Page 4 Rev.00 1. TEST RESULT CERTIFICATION Applicant: Vernier Software & Technology 13979 SW Millikan Way Beaverton, OR 97005 Equipment Under Test: LabQuest2 Tr a d e N a m e : Vernier Model: LQ2-LE Date of Test: February 14, 2012 ~ April 1, 2013 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2009 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements set forth in the above standards. The test results…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Reference No.: T120205G01-RP2 FCC ID: AUO-LQ2-LE Report No.: T130325W06-RP2 Page 80 Rev.00 APPENDIX I PHOTOGRAPHS OF TEST SETUP Conducted Emission Set Up Photo Compliance Certification Services Inc. Reference No.: T120205G01-RP2 FCC ID: AUO-LQ2-LE Report No.: T130325W06-RP2 Page 81 Rev.00 Radiated Emission Set up Photos Compliance Certification Services Inc. Reference No.: T120205G01-RP2 FCC ID: AUO-LQ2-LE Report No.: T130325W06-RP2 Page 82 Rev.00 Powerline Conducted Emissions Setup Photos