B32UX301SMRFID Reader Module

Verifone Part Number DOC159-026-EN-A, Revision A.2 UX301 Installation Guide All rights reserved. No part of the contents of this document may be reproduced or transmitted in any form without the written permission of Verifone, Inc. The information contained in this document is subject to change without notice. Although Verifone has attempted to ensure the accuracy of the contents of this document, this document may include errors or omissions. The examples and sample programs are for illustration only and may not be suited for your purpose. You should verify the applicability of any example or sample program before placing the software into productive use. This document, including without limitation the examples and software programs, is supplied “As-Is.” Verifone, Inc. 2099 Gateway Place, Suite 600 San Jose, CA, 95110 USA www.verifone.com Verifone Part Number DOC159-026-EN-A, Revision A.2 UX301 Installation Guide © 2015 Verifone, Inc. Verifone, the Verifone logo, Omni, VeriCentre, Verix, and ZonTalk are registered trademarks of Verifone. Other brand names or trademarks associated with Verifone’s products and services are trademarks of Verifone, Inc. All other brand names and trademarks appearing in this manual are the property of their respective holders. Comments? Please e-mail all comments on this document to your local Verifone Support Team. SETUP Cable Connections UX301 I NSTALLATION GUIDE17 8Slide the cardholder cover back, locking it into place. Figure 7Replacing the SAM Cardholders 9Install additional SAM cards in the available slots as necessary. Cable Connections The UX301 rear panel holds several interface ports for power and communications. Use this section to see how the UX301 connects to various UX- series units, as well as other devices. •Connecting to a UX-Series Host Device •Connecting to a UX-Series Peripheral Device •Connecting Optional Devices Connecting to a UX-Series Host Device This section discusses the connection of the UX301 device with the following host units: Connecting to a Vending Machine You can connect the UX301 to a host vending machine (VM) with any of the following connection types: •USB Type B •ETH (LAN) •COM (RS-232) •MDB For more information regarding your card reader configuration and your cabling needs, contact your local Verifone service provider. For cable ordering information, see Accessories and Documentation). 58)MAGE0LACEHOLDER NOTE To get the proper connection cables, please refer to Accessories and Documentation. The I/O ports of the EUT are listed below: SAM Card Slot *3 USB Port *3 Smart Card Slot *1 SMA port *1 RJ45 Port *2 LAN Port *1 SETUP Cable Connections 18UX301 INSTALLATION GUIDE Connecting to a UX-Series Peripheral Device This section discusses the connection of the UX301 device with the following peripheral units: •Connecting to a UX1xx Series PIN Pad •Connecting to a UX401 CTLS Unit Connecting to a UX1xx Series PIN Pad You can connect the UX301 to a UX1xx-series PIN pad device with a standard USB Type A to B cable (VPN CBL000-045-01-A). Figure 8Connecting to a UX110 PIN Pad Connect the Type A plug in the UX301 high-powered port and connect the type B plug to the USB port of the UX110. Use the same procedure for connecting to other UX1xx-series PIN pads. The UX301 host device installs the USB device driver automatically. The USB data will be encrypted with authentication upon startup. Connecting to a UX401 CTLS Unit You can connect the UX301 to a UX401 unit using a communication cable (VPN CBL159-313-02-A) and an SMA / analog RF cable (VPN CBL159-302-03-A). To connect the UX301 to the UX401 CTLS unit 1Attach one end of the comm cable to the UX301 and the other end to the UX401. 58)MAGE0LACEHOLDER 2 Attach one end of the SMA cable to the UX301 and the other end to theUX401. UX301 INSTALLATION GUIDE27 CHAPTER 3 Specifications This chapter discusses power requirements, dimensions, and other specifications of the UX301 card reader. Unit Power Requirements •Operation voltage: 8 to 43V DC, 24V DC for Printer use •Idle Power: 2W •Typical Power: 3W (CTLS read), 4W (UX100 display heater), 0.5W (UX100/ 110), 5W (RS232-vout) •Sleep Mode: TBD. Temperature•Operating temperature: •-30°C to 70°C (-22°F to 158°F) Standard unit •Storage temperature: -25°C to 70°C (-13°F to 158°F) •Power Supply rated for indoor use only: 12V DC 3.3A, operating temperature 0°C to 40°C (32°F to 104°F) •Power Supply rated for outdoor use: 24V, DC 3.75A up to 40°C (DC 2.5A up to 60°C), operating temperature -25°C to 60°C •Relative humidity: 5% to 90% RH non-condensing •External Dimensions •Height: 67 mm (2.64 in) •Width: 97 mm (3.82 in) •Depth 102 mm (4.02 in) Memory•128 MB DDRAM •256 MB NAND-Flash Magnetic Stripe Card •Triple-track NOTE If this device is to be used in the Nordic countries, or in any environment where the temperature range exceeds the product’s operating temperature, it is the responsibility of the integrators to ensure that the ambient environment is controlled in such a way to ensure that the product operates within the specified temperature range. SPECIFICATIONS 28UX301 INSTALLATION GUIDE Smart Card Reader•Non-sliding •Card conserving plated landing contacts SAM Requirements•3 SAM slots Peripheral Ports•Consistent ports: •Power •Powered USB Type A for external device (host) •USB Type B (client) •COM1 (powered) •ETH (LAN) connection with 2 colored LEDs for link state and speed indication •Analog RF CTLS antenna connector to the UX401 CTLS unit •8-PIN to RJ-45 connector to UX401 CTLS antenna unit Model dependent board: •MDB Communication•COM: Up to 115200 bps,HW RTS/CTS handshake •MDB: 9600 bps fix, 9E1 Display•3 status LEDs on the front (payment application controlled) UX301 INSTALLATION GUIDE29 CHAPTER 4 Maintenance and Cleaning Your card reader should be treated with care. It has no user-serviceable parts. The following suggestions will help you protect your warranty coverage. •Do not store the device in hot areas. High temperatures can…

Text truncated - open the document above for the full version.

B32UX301SM

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 3 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 3 Rev 5.0 2015.4.22 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, _ VeriFone Inc._hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): (RFID Reader Module, UX301) FCC ID: B32UX301SM Sincerely, Client’s signature Client’s name / title Don Perkins/ Director Engineering Contact information / address: 1400 West Stanford Ranch Road Suite 200 Rocklin, CA 95765 , UNITED STATES

SCS-F26 Modular Approval Letter Page 1 of 4 Rev 10.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Modular Approval Declaration Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (Obsolete) 1.0 1.0 Dec-04-2006 Added IC Modular Letter (Obsolete) 1.0 2.0 Feb 16 2009 Add LMA and MA option (Obsolete) 2.0 3.0 April 14 2010 Revised per RSS Gen issue 3.0 (Obsolete) 3.0 4.0 Jan 12 2011 Removed Foot(2) (obsolete) 4.0 5.0 July 19 2011 Adding New note per KDB996369 D01 V01R03 (obsolete) 5.0 6.0 August 29 2011 Updated company template & Added text box (obsolete) 6.0 7.0 Jan-31-2012 Updated modular requirement (obsolete) 7.0 8.0 Sept 05 2014 Updated template to meet RSP 100 issue 10 (obsolete) 8.0 9.0 Nov 20 2014 Updated template to meet RSP 100 issue 11 (current) 9.0 10.0 March 19 2015 SCS-F26 Modular Approval Letter Page 2 of 4 Rev 10.0 (Company Letter head) (Date) 2015.4.16 (Product name) FCC ID : B32UX301SM , is seeking FCC Authorization as a Single Modular transmitter / Single Limited Modular Approval (Please check one). The EUT meets the requirements for Single Modular approval / Single Limited Modular Approval (please check one) as detailed in FCC public Notice DA00-1407. Compliance to each of the requirements is described below : Questions are: * Please provide a detailed explanation if the answer is “No.” Item Modular requirement Yes No 1 The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly; ˅ 2 The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal; ˅ 3 The module must contain power supply regulation on the module; ˅ 4 The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b); ˅ 5 The module must demonstrate compliance in a stand-alone configuration; ˅ 6 The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements); ˅ 7 The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee; ˅ 8 The module must comply with RF exposure requirements ˅ Note: (1) LMA may be granted when one or more of the requirements in the table above cannot be demonstrated. LMA will also be issued in those instances where applicants can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must state that the module is only approved for use when installed in devices produced by a specific manufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product into which the module will be installed, and will be maintained, such that full compliance of the end product is always ensured. (2) Please provide Clear and specific instructions describing the conditions, limitations and procedures for third-parties to use and/or integrate the module into a host device. (3) For non-Software Defined Radio transmitter modules where software is used to ensure compliance of the device, technical description of how such control is implemented to ensure prevention of third party modification must be provided (see KDB 594280). Note 1: Compliance of a module in its final configuration is the responsibility of the applicant. A host device will not be considered certified if the instructions regarding antenna configuration provided in the original description, of one or more separately certified modules it contains, were not followed. Example: A separately certified low-power transceiver module using Bluetooth technology which is housed in a desktop computer, laptop or peripheral does not require the overall system to be recertified, if the desktop computer, laptop or peripheral, as a stand-alone unit, complies with all applicable technical standards.

UX301 2015-4-20 RFID Reader Module

FCC Test Report Report No.: RF- V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. Page : A2-1 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 Attachment 2 External Photographs of EUT FCC Test Report Report No.: RF- V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. Page : A2-1 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 UX301 FCC Test Report Report No.: RF- V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. Page : A2-2 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 FCC Test Report Report No.: RF- V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. Page : A2-3 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 FCC Test Report Report No.: RF- V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. Page : A2-4 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 Antenna UX401 FCC Test Report Report No.: RF- V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. Page : A2-5 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 FCC Test Report Report No.: RF- V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. Page : A2-6 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546

Label Location

SIGNA TURES REV. DWG.NO. SIZE TITLE DATE SCALE: SHEET DWN. ENG.CHK. OF XXX ECO# CXXXXX 6/28/13 Nick_C2 LABEL QX400 PROD ID UL CE ARTWORK, LBLXXX-XXX-XX-AW XXX A4 2X VICTORIA_L1 Nick_C2 6/28/13 6/28/13 THIS DOCUMENT IS TH E PROPERTY OF VERIFONE, AND CONTAINS VERIFONE'S CONFIDENTIAL AN D PROPRIETARY IN FORMATION IN CONSIDERATION OF VERIFONE'S DISCLOSURE OF THIS DOCUMENT TO YOU, YOU AGREE THAT N EITHER IT, NOR THE INFORMATION CONTAINED THEREIN SHALL BE DI SCLOSED T O OTHERS OR DUPLICATED, IN WHOLE OR IN PART, OR USED FOR ANY PURPOSES OTHER THAN AGREED T O BY VE RIFONE, WITHOUT EX PRESS WRITTEN CONSENT OF VERIFONE. THIS ARTWORK IS THE PROPER TY OF VERIFONE. HANDLE WITH CARE AND RETURN TO VERIFONE VER Y S OON AFTER USE. UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN MILLIMETERS. 11 REV. DESCRIPTION DATE APPROVED REVISIONS 39 22.5 R San Jose, CA. USA LBLXXX-XXX-XX-A Model:  X 400 FCC ID:B32UX400CTLS I.T.E. Notes:1.Background:Matte silver 2.Logo & text: Black 28JUN13 MADE IN MAYLASIA VEN B32UX300400 This device complies with Part 15 of theFCC Rules. Operation is subject to thefollowing two conditions: (1) this device may not causeharmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation. B32UX301401 %8;60

FCC RF Test Report Report No.: RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. Page : A3- TEL. : 886-2-25984542 FAX. : 886-2-25984546 0 Attachment 3 Internal Photographs of EUT FCC RF Test Report Report No.: RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. Page : A3- TEL. : 886-2-25984542 FAX. : 886-2-25984546 1 UX301 FCC RF Test Report Report No.: RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. Page : A3- TEL. : 886-2-25984542 FAX. : 886-2-25984546 2 FCC RF Test Report Report No.: RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. Page : A3- TEL. : 886-2-25984542 FAX. : 886-2-25984546 3 FCC RF Test Report Report No.: RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. Page : A3- TEL. : 886-2-25984542 FAX. : 886-2-25984546 4 FCC RF Test Report Report No.: RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. Page : A3- TEL. : 886-2-25984542 FAX. : 886-2-25984546 5 FCC RF Test Report Report No.: RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. Page : A3- TEL. : 886-2-25984542 FAX. : 886-2-25984546 6 RF IC: PN512 FCC RF Test Report Report No.: RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. Page : A3- TEL. : 886-2-25984542 FAX. : 886-2-25984546 7 Antenna UX401 FCC RF Test Report Report No.: RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. Page : A3- TEL. : 886-2-25984542 FAX. : 886-2-25984546 8 FCC RF Test Report Report No.: RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. Page : A3- TEL. : 886-2-25984542 FAX. : 886-2-25984546 9 FCC RF Test Report Report No.: RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. Page : A3- TEL. : 886-2-25984542 FAX. : 886-2-25984546 10

FCC RF Test Report Report No.:RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. Page : 1/47 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 FCC Test Report for RFID Reader Module Trade Name : Verifone Model Number : UX301 Antenna Model No. : UX401 FCC ID : B32UX301SM Report Number : RF-V040-1503-101 Date of Receipt : April 15, 2015 Date of Report : April 23, 2015 Prepared for Verifone Inc. 1400 West Stanford Ranch Road, Suite 200, Rocklin, CA, 95765, UNITED STATES Prepared by Central Research Technology Co. EMC Test Laboratory 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. NVLAP LAB CODE 200575-0 This report shall not be reproduced, except in full, without the written approval of Central Research Technology Co.. It may be duplicated completely in its entirely for legal use with the permission of the applicant. It should not be used to claim product endorsement by NVLAP, NIST or any U.S. government agency. The test result in the report applies only to the sample tested. FCC RF Test Report Report No.:RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. Page : 2/47 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 Vertification Equipment Under Test : RFID Reader Module Model No. : UX301 Antenna Model No. : UX401 FCC ID : B32UX301SM Applicant : Verifone Inc. Address : 1400 West Stanford Ranch Road, Suite 200, Rocklin, CA, 95765, UNITED STATES Applicable Standards : FCC Part 15, Subpart C Date of Testing : April 15, 2015 ~ April 21, 2015 Deviation : N/A Condition of Test Sample : Mass Production We, Central Research Technology Co., hereby certify that one sample of the designated product was tested in our facility during the period mentioned above. The test records, data evaluation and Equipment Under Test (EUT) configurations shown in the present report are true and accurate representation of the measurements of the sample’s RF characteristics under the conditions herein specified. The test results show that the EUT as described in the present report is in compliance with the requirements set forth in the standards mentioned above and apply to the tested sample identified in the present report only. The test report shall not be reproduced, except in its entirety, without the written approval of Central Research Technology Co. FCC RF Test Report Report No.:RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. Page : 3/47 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 Contents 1. General Description .............................................................................................. 5 1.1 GENERAL DESCRIPTION OF EUT ................................................................................ 5 1.2 TEST METHODOLOGY ................................................................................................ 6 1.3 TEST MODE .............................................................................................................. 6 1.4 A PPLIED STANDARDS ................................................................................................. 7 1.5 THE SUPPORT UNITS ............................................................................................... 10 1.6 LAYOUT OF SETUP ................................................................................................... 11 1.7 TEST CAPABILITY .................................................................................................... 12 1.8 MEASUREMENT UNCERTAINTY .................................................................................. 14 2. Conducted Emission Measurement .................................................................. 15 2.1 LIMITS FOR EMISSION MEASUREMENT ....................................................................... 15 2.2 TEST INSTRUMENTS ................................................................................................. 16 2.3 T EST PROCEDURES ................................................................................................. 17 2.4 TEST CONFIGURATIONS ........................................................................................... 18 2.5 TEST DATA .............................................................................................................. 19 3. Field Strength of fundamental Measurement .................................................... 23 3.1 APPLIED STANDARD ................................................................................................ 23 3.2 TEST INSTRUMENTS ................................................................................................. 24 3.3 MEASUREMENT PROCEDURE .................................................................................... 25 3.4 TEST CONFIGURATION ............................................................................................. 26 3.5 T EST RESULTS ........................................................................................................ 27 4. Radiated Emission .............................................................................................. 31 4.1 APPLIED STANDARD ................................................................................................ 31 4.2 TEST INSTRUMENTS ................................................................................................. 32 4.3 M EASUREMENT PROCEDURE .................................................................................... 33 4.4 TEST CONFIGURATION ............................................................................................. 34 4.5 T EST RESULTS ........................................................................................................ 35 5. Frequency Tolerence .......................................................................................... 37 5.1 APPLIED STANDARD ...........…

Text truncated - open the document above for the full version.

FCC Test Report Report No.:RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. Page : A1-1 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 Attachment 1 Photographs of the Test Configurations FCC Test Report Report No.:RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. Page : A1-i 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 Contents 1. Radiated Emission Measurement ............................................................. 1 2. Conducted Emission Measurement .......................................................... 3 FCC Test Report Report No.:RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. Page : A1-1 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 1. Radiated Emission Measurement Below 30MHz FCC Test Report Report No.:RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. Page : A1-2 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 Above 30MHz FCC Test Report Report No.:RF-V040-1503-101 CENTRAL RESEARCH TECHNOLOGY CO. Page : A1-3 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 2. Conducted Emission Measurement