B4S20016398PC Remote Controller

C HANGING THE T RANSMIT /R ECEIVE CHANNELS : If a number of PC’s are being remotely controlled in the immediate vicinity (within about 10 meters), interference may occur. This can be overcome by selecting different channels. Only change the remote control in the event of interference . To do so proceed as follows: 1. Press and hold the Setup key , until the LED goes out. 2. Release the Setup key. The LED flashes. Now enter the appropriate code using the numerical keys (1, 2, etc. up to 16). 3. Now press the Setup key briefly. The LED lights briefly, to indicate suc- cessful programming. 4. Now enter the appropriate code in the Power Cinema Setup program. B ATTERY DISPOSAL Â Important: Batteries are special category waste and must be disposed of properly. We will be happy to take back your old batteries. Replace the batteries only with batteries of the same or an equivalent type. FCC C AUTION THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. This equipment generates and uses radio frequency energy, and if not installed and used properly, that is, in strict accordan ce with the manufacturers instructions, it may cause interference to radio and televisi on reception. It has been type tested and found to comply with the limits for re mote control devices in accordance with the specifications in Sub-Parts B and C of Part 15 of FCC Rules, which are designed to provide reasonable protection against su ch interference in a residential installa- tion. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television recep-tion, which can be determined by unplugging the equipment, try to correct the inter- ference by one or more of the following measures. * Reorient the antenna of the radio/TV experiencing the interference. * Relocate the equipment with respect to the radio/TV. * Move the equipment away from the radio/TV. * Plug the equipment into an outlet on a different electrical circuit from the radio/TV experiencing the interference. * If necessary, consult your local dealer for additional suggestions. NOTE: Modifications to this product will vo id the user's authority to operate this equipment. I NSTRUCTIONS FOR PC REMOTE CONTROLLER Note : This wireless remote control set can only be used to control the Power Cinema program on your PC. In order for it to work, the following conditions must be met: - The PC must be booted up. - Windows ® XP must be fully loaded. - The driver software must be installed*. - Power Cinema installed*. - Receiver connected to a USB port. * All these conditions are met in the delivered state. I NSERTING BATTERIES 1. Turn the remote controller upside down. 2. Open the battery compartment by carefully pulling the clip on the cover and lifting it at the same time. 3. Insert two batteries (type: AA, Micro) in the battery compartment. Ensure that the polarity corresponds to the illustration etched on the inside of the battery compartment (+ must correspond with + and – with –). 4. Close the battery compartment again. I NSTALLING THE REMOTE CONTROL RECEIVER It does not matter if the PC is switched on or off when you connect up the re- mote control receiver. The necessary driver software is already installed on your computer. The driver is part of Power Cinema and is installed along with the program. 1. Boot up your PC and wait for Windows ® to load fully. 2. Insert the USB plug of the remote control receiver in a free USB slot (refer to your PC operating manual). Your PC will automatically detect the new device and automatically integrate it provided that the driver has been in-stalled (delivered state). 3. You can now use the remote controller to operate the Power Cinema program. S Key Description TV PREVIEW CHANNEL LIST For selecting the corresponding application for TV, video, DVD, music, radio and photo. Once the channel has been se-lected use the TV-PREVIEW key to see a preview of the TV programs and the CHANNEL LIST key to call up a list of the saved programs. SETUP VIDEO DESKTOP Use the SETUP key for remote controller channel programming. VIDEO DESKTOP allows you define a fi lm that is currently being shown for your desktop wallpaper. CHAN + VOL - VOL + CHAN - The CHAN +/- keys are used for program selection. VOL +/- increase or decrease the volume. The key in the middle mutes the sound. These keys are used to operate the Video-text. CHN. SEARCH DELETE The keys with numbers on them are used for direct frequency input and for renaming files and channels. To enter text press the key repeatedly until the letter you want appears. Press OK, to confirm your choice. Use DELETE to clear the last input. If you wait for about 3 seconds the input is auto-matically confirmed. The CHN. SEARCH key starts the TV and radio channel search. Key Description RENAME SNAPSHOT Use the RENAME key for renaming files. You can use SNAPSHOT to take a snapshot from a film or television program that is currently showing. This snapshot is automatically saved as an image. The arrow keys move the cursor of the mouse in the corresponding direction. This function only works in the Power Cinema program. Press OK to confirm your choice. ACQUIRE IMAGE EDIT IMAGE ACQUIRE IMAGE starts a dialogue for reading in images. EDIT IMAGE allows you to add effects to your images. FULL SCREEN The  key starts playback. Use  /  for fast forward or rewind. The  key pauses playback, while  ends it.  jumps to the end,  to the start. Start recording by pressing . The FULL SCREEN key changes the size of the win- dow. DVD MENU DVD AUDIO DVD MENU calls up the menu for DVD playback. Use DVD AUDIO for DVD sound control. The ON/OFF button starts and end the Power Cinema program. PHOTO RADIO MUSIC DVD VCR TV…

Text truncated - open the document above for the full version.

MCU (EM78P447S) Block Diagram for MD4688PC RF REMOTE Key Matrix 433MHzTransmitter 433MHz

0536 RF Remote Control Use two 1.5V AAA alkaline batteries. Medion Remote Control rating label 2: 1 4/23/03 P/N 20016398 FCC ID: B4S20016398 ® www.medion.com Made in China

1 2 34 ABCD 4 3 2 1 D CBA Title Number Revision Size A4 Date: 22-Jan-2003 Sheet of File: A:\M_RF433_.SCH Drawn By: TR1H10 R1 10K R310K R2 150R C61P C55P6 C2 * C322PC14P7 L2 8MM L318T L1 3.5T SAW1 433MHz RF INPUT +3V C41P RF 433MHz Tx 90MMAntenna PCB TRACE

DCBA 12345678 ABCD 8 7 6 5 4 3 2 1 PICO ELECTRONICS Ltd., Eastfield Industrial Estate, Glenrothes, Fife, KY7 4NZ, SCOTLAND SHEET No. DATEDATE REVISION DATE FIRST DRAWN FILEDRNAPPD. DO NOT SCALE DRAWING TITLE: REV. Error : PICO.WMF File Not Found D:\BACKUP\MEDION\PCB\FCC.~CH 11 of A MEDION PRINT DATE 09:44:12 15-Jan-2003 7/1/03 6/01/03 LED1RED R51K VSS C7100UF10V Y1 4MHZ R41M VSS VSS 2 x AAA BATTERIES BATT1BATT2 +3V NOTES:-1/ ALL UNSPECIFIED DIODES 1N4148 OR EQUIVALENT.2/ ALL UNSPECIFIED DAUGHTER BOARD CAPACITORS ARE SMD TYPE.3/ ALL UNSPECIFIED DAUGHTER BOARD RESISTORS ARE SMD TYPE.4/ ALL UNSPECIFIED RESISTORS ARE 0.125W 5%.5/ ALL UNSPECIFIED CAPACITORS ARE AXIAL MLC TYPE."*" DENOTES COMPONENT NOT INSTALLED SIGNAL KEY17MUTE KEY26OKKEY34RENAME KEY36 KEY45PAUSEKEY5RECKEY13CHANNEL LIST KEY1TV/RADIO KEY2KEY10DVDKEY18 KEY44 KEY9PHOTOKEY250 RF DAUGHTER BOARD SHOWN FOR REFERENCE ONLY DAUGHTER BOARD KEY41KEY33DEL TCC 1 VDD 2 NC 3 INT 5 P50 6 P51 7 P52 8 P53 9 P60 10 P61 11 P62 12 P63 13 P64 14 VCC 4 RES 28 P65 15 P66 16 P67 17 P70 18 P71 19 P72 20 P73 21 P74 22 P75 23 P76 24 P77 25 OSCO 26 OSCI 27 U1 EM78P447S R6100K C61NF VSS KEY67 KEY24SETUP KEY308 KEY315 KEY389 KEY396 KEY14VCR KEY74KEY47DVD MENU KEY50BLUE KEY52SNAP SHOOT KEY49YELLOW KEY54CH- KEY55GREEN KEY56RED TR1H10 R1 10K R310K R2 150R C6 * C55P6 C2 100P C322PC15P6 L2 8mm L318T L1 3.5T SAW1 433MHz C41P VSS KEY27KEY43EDIT IMAGEKEY3 ACQUIRE IMAGE KEY11TV PREVIEWKEY19VOL+KEY35CH+ KEY28PLAYKEY4KEY12MUSICKEY20 KEY22FULL SCREEN KEY21DVD AUDIO KEY23VOL- KEY29STOPKEY37VIDEO DESKTOPKEY53PINK KEY15TV KEY81KEY16RADIOKEY322KEY403KEY48POWER PCB trace

Test Report No. R-9881-1 FCC ID: B4S20016398 APPLICANT X-10 USA, Inc. 19823, 58 th Place S. Kent, WA 98032 MANUFACTURER X-10 Electronics Shenzhen Co. Ltd. X-10 Building Labour Industrial District Shenzhen, Xixiang, Bao An Guang Dong, China, 518102 TEST SPECIFICATION: FCC Rules and Regulations Part 15, Subpart C, Para. 15.231 TEST PROCEDURE: ANSI C63.4:2000 TEST SAMPLE DESCRIPTION BRANDNAME: X-10 USA Part Number: 20016398 TYPE: Pulsed Transmitter POWER REQUIREMENTS: 3 VDC derived from 2 “AAA” Batteries FREQUENCY OF OPERATION: 433 MHz TESTS PERFORMED Para. 15.231(b), Radiated Emissions, Fundamental and Harmonics Para. 15.231(b), Radiated Emissions, Spurious Case Para. 15.35, Duty Cycle Determination Para. 15.231(c), Occupied Bandwidth REPORT OF MEASUREMENTS Applicant: X-10 (USA), Inc. Brand Name: Medion Device: Pulsed Transmitter FCC ID: B4S20016398 Test Report No. R-9881-1 FCC ID: B4S20016398 Power Requirements: 3 VDC derived from 2 “AAA” Batteries Applicable Rule Section: Part 15, Subpart C, Section 15.231 Test Report No. R-9881-1 FCC ID: B4S20016398 REPORT OF MEASUREMENTS (continued) TEST RESULTS 15.231 (a): This device is used as a remote control transmitter. 15.231 (a)(1) & The transmitter is manually operated and ceases transmission within 5 15.231(a)(2): seconds after deactivation. 15.231 (a)(3): The transmitter does not perform periodic transmissions. 15.231 (b): The fundamental field strength did not exceed 10,966 μV/M (Average) at a test distance of 3 meters. In addition, the requirements of section 15.35 for averaging pulsed emissions and for limiting peak emissions were met. The field strength of harmonic and spurious emissions did not exceed 1,096 μV/M (AVERAGE). DETERMINATION OF FIELD STRENGTH LIMITS The field strength limits shown below are found in Section 15.231. Frequency Limit F1 = 260 3750 = L1 Fo = 433 Lo F2 = 470 12500 = L2 Test Report No. R-9881-1 FCC ID: B4S20016398 REPORT OF MEASUREMENTS (continued) The formula below was utilized to determine the limits: Limit = L1 + [(Fo-F1)(L2-L1)/(F2-F1)] Solving yields: Fundamental Limit = 10,966 μV/M (AVERAGE) @ 3 Meters Harmonic Limit = 1,096 μV/M (AVERAGE) @ 3 Meters DUTY CYCLE DETERMINATION The unit’s RF output was directly coupled to the input of the spectrum analyzer. The analyzer was set for a frequency span of 0Hz. The sweep time was then adjusted in order to display one full pulse train. The transmitter on time was then summed and compared to the time for one full cycle in order to obtain the duty cycle. Transmitter On Time = 13.04 milliseconds (maximum) Transmitter Cycle Time = 38.8 milliseconds Transmitter Duty Cycle = 33.6 % See separate e-file for plots named dutycycle.pdf for additional information. Test Report No. R-9881-1 FCC ID: B4S20016398 SPECTRUM ANALYZER DESENSITIZATION CONSIDERATIONS Due to the nature of the emissions being measured, care was taken to ensure that the resolution bandwidth of the spectrum analyzer was adequate to provide accurate measurements. The following formula was utilized: Setting pulse desensitization equal to zero and utilizing the minimum observed pulse width of 440 μs yields a minimum required bandwidth of 1,515 Hz. FCC specified bandwidths of 100kHz and 1MHz were utilized below and above 1GHz, respectively. GENERAL NOTES All readings were taken utilizing a peak detector function at a test distance of 3 meters. The duty cycle was applied to the peak readings in order to determine the average value of the emissions. The frequency range was scanned from 30 MHz to 4.33 GHz. All emissions not reported were more than 20 dB below the specified limit. Test Report No. R-9881-1 FCC ID: B4S20016398 EQUIPMENT LIST FCC Part 15, Subpart C Section 15.231 EN Type Manufacturer Description Model No. Cal Date Due Date 067 Open Area Test Site Retlif 3 Meter RNY 09/20/2000 09/20/2003 128 Double Ridged Guide Electro-Mechanics 1 GHz - 18 GHz 3105 06/07/2002 06/07/2003 133 Broadband Pre-Amplifier Electro-Metrics 10 kHz - 1 GHz, 26dB BPA-1000 06/11/2002 06/11/2003 141 Spectrum Analyzer Hewlett Packard 100 Hz - 40 GHz 8566B 01/23/2003 07/23/2003 141A Graphics Plotter Hewlett Packard N/A 7470A 03/05/2003 03/05/2004 141B Quasi-Peak Adaptor Hewlett Packard 100 Hz - 1 GHz 85650A 01/23/2003 07/23/2003 206B 6.0 dB Attenuator Texscan 0 - 1.0 GHz FP-50 - 6 dB 06/11/2002 06/11/2003 543 Preamplifier Hewlett Packard 1.0 GHz - 26.5 GHz 8449B 07/11/2002 07/11/2003 617 Interference Analyzer Electro-Metrics 10 kHz - 1 GHz EMC-30 08/23/2002 08/23/2003 767 Biconilog EMCO 26 - 2000 MHz 3142B 09/03/2002 09/03/2003 Test Report No. R-9132-1 FCC ID: B4S20016398 FCC 15.231(b) RADIATED EMISSIONS, FUNDAMENTAL & SPURIOUS CASE (See separate e-file named Refundharm & REspur.pdf) FCC 15.231(c) OCCUPIED BANDWIDTH (See separate e-file named occbw.pdf) Test Report No. R-9881-1 FCC ID: B4S20016398 FCC 15.231(c) DUTY CYCLE (See separate e-file named dutycycle.pdf) Test Report No. R-9881-1 FCC ID: B4S20016398 Test Setup Photograph