B4SCR14APan n' Tilt Remote

To clear all stored positions: Press and hold Center then flip the switch at the bottom to Program and back. Pan ‘n Tilt Remote For use with X10 wireless cameras Model CM14A CM14A-8/01 1. Install 4 AAA alkaline batteries (sold separately) in the remote’s battery compartment. 2. Use a dime to set the Housecode dial to match the cameras, and transceiver you want to use the remote with. 3. Plug in an X10 Transceiver (RR501 or TM751, sold separately). Set Housecode to match remote. Fully extend the antenna. 4. To control up to 4 Cameras, attach each one to a ZC15A Pan and Tilt base (sold separately), plug each ZC15A into its own Addressable Power Supply, and set each power supply to the same Housecode you used in steps 2 and 3. Set each power supply to a unique number between 1 and 4. Pressing any Camera button (C1, C2, C3, or C4) turns on that camera (1, 2, 3, or 4) and turns the others (in the group) off. Then, each press of either the or button turns on the next or previous camera in the group of 4 while turning the current camera off. (You set all cameras to the same channel as the Video Receiver connected to your TV (Channel A, B, C, D). 5. After you press the "C" button to turn on a camera, pressing a left or right BLUE button at the top “pans” the camera left or right. Pressing a BLUE up or down button “tilts” the camera up or down. 6. To make buttons C1 thru C4 control cameras 5-8 (instead of 1 thru 4) press (and hold) the C2 button then flip the switch at the bottom from Normal to Program and back. Buttons C1, C2, C3, and C4 now control cameras set to 5, 6, 7, and 8. 7. Pressing C3 in step 6 sets buttons C1, C2, C3, and C4 to control cameras set to 9, 10, 11, and 12. 8. Pressing C4 in step 6 sets buttons C1, C2, C3, and C4 to control cameras set to 13, 14, 15, and 16. Buttons P1 thru P4 are used to store 4 position settings for each of the 4 cameras controlled by buttons C1 thru C4. 1. To store the first position for the camera controlled by C1, press C1. 2. Press the blue buttons to scan to the position you want. 3. Press and hold P1, then flip the switch at the bottom from Normal to Program and back, to store that position under P1. 4. Repeat steps 2 and 3, pressing P2 to store another position under P2. 5. Repeat for P3, and P4. Repeat steps 1 thru 4 to store 4 positions for C2, C3, and C4. Press the “C” button for any camera, following by any “P” button to move to the position stored under that button for that camera. Press the “C” button then Sweep to sweep through all 4 positions stored for that camera. Press the “C” button then Center to center the position for that camera. Installation and operating instructions The CR14A Remote lets you turn on any of 4 cameras or scan each of them in turn (forward or backward) so as to display the image from each camera in turn on your TV. If you purchase a Camera Pan and Tilt base (model ZC15A) for each camera, you can also use the remote to move the position of the camera from left to right (Pan) and up and down (Tilt). The Remote sends Wireless Radio Frequency (RF) signals to an X10 Transceiver (RR501 or TM751). The Transceiver then passes the signals onto your house wiring to control Wireless Cameras around your home. You connect each camera (up to 4) to a ZC15A base and plug each ZC15A into Addressable Power Supplies each set to a different number. The CR14A normally controls Cameras set to Unit Codes 1, 2, 3, 4. But you can set it to control cameras set to 5, 6, 7, 8, or 9, 10, 11, 12, or 13, 14, 15, 16. Program SCAN SweepCentre Normal A C E G I K M O . . . . .. . . CAMERA C1 C3 C2 C4 POSITION P1P2 P4P3 Set to the same letter as the TM751 and cameras. Scans forward or backward thru cameras controlled by C1 thru C4. “Pans” left and right. “Tilts” up and down. Write locations of cameras here. Controls 4 cameras. Stores the positions for 4 cameras. F.C.C. CAUTION - THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TO THE UNITS. ANY CHANGES MADE TO THE UNITS WILL VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. LIMITED 1-YEAR WARRANTY Please visit www.x10.com/warranty to complete your on-line warranty registration. Thank you. For help or more information on setup, please visit: www.x10.com/support Centers each camera position. Sweeps thru the 4 stored positions for the selected camera.

To clear all stored positions: Press and hold Center then flip the switch at the bottom to Program and back. Pan ‘n Tilt Remote For use with X10 wireless cameras Model CM14A CM14A-8/01 1. Install 4 AAA alkaline batteries (sold separately) in the remote’s battery compartment. 2. Use a dime to set the Housecode dial to match the cameras, and transceiver you want to use the remote with. 3. Plug in an X10 Transceiver (RR501 or TM751, sold separately). Set Housecode to match remote. Fully extend the antenna. 4. To control up to 4 Cameras, attach each one to a ZC15A Pan and Tilt base (sold separately), plug each ZC15A into its own Addressable Power Supply, and set each power supply to the same Housecode you used in steps 2 and 3. Set each power supply to a unique number between 1 and 4. Pressing any Camera button (C1, C2, C3, or C4) turns on that camera (1, 2, 3, or 4) and turns the others (in the group) off. Then, each press of either the or button turns on the next or previous camera in the group of 4 while turning the current camera off. (You set all cameras to the same channel as the Video Receiver connected to your TV (Channel A, B, C, D). 5. After you press the "C" button to turn on a camera, pressing a left or right BLUE button at the top “pans” the camera left or right. Pressing a BLUE up or down button “tilts” the camera up or down. 6. To make buttons C1 thru C4 control cameras 5-8 (instead of 1 thru 4) press (and hold) the C2 button then flip the switch at the bottom from Normal to Program and back. Buttons C1, C2, C3, and C4 now control cameras set to 5, 6, 7, and 8. 7. Pressing C3 in step 6 sets buttons C1, C2, C3, and C4 to control cameras set to 9, 10, 11, and 12. 8. Pressing C4 in step 6 sets buttons C1, C2, C3, and C4 to control cameras set to 13, 14, 15, and 16. Buttons P1 thru P4 are used to store 4 position settings for each of the 4 cameras controlled by buttons C1 thru C4. 1. To store the first position for the camera controlled by C1, press C1. 2. Press the blue buttons to scan to the position you want. 3. Press and hold P1, then flip the switch at the bottom from Normal to Program and back, to store that position under P1. 4. Repeat steps 2 and 3, pressing P2 to store another position under P2. 5. Repeat for P3, and P4. Repeat steps 1 thru 4 to store 4 positions for C2, C3, and C4. Press the “C” button for any camera, following by any “P” button to move to the position stored under that button for that camera. Press the “C” button then Sweep to sweep through all 4 positions stored for that camera. Press the “C” button then Center to center the position for that camera. Installation and operating instructions The CR14A Remote lets you turn on any of 4 cameras or scan each of them in turn (forward or backward) so as to display the image from each camera in turn on your TV. If you purchase a Camera Pan and Tilt base (model ZC15A) for each camera, you can also use the remote to move the position of the camera from left to right (Pan) and up and down (Tilt). The Remote sends Wireless Radio Frequency (RF) signals to an X10 Transceiver (RR501 or TM751). The Transceiver then passes the signals onto your house wiring to control Wireless Cameras around your home. You connect each camera (up to 4) to a ZC15A base and plug each ZC15A into Addressable Power Supplies each set to a different number. The CR14A normally controls Cameras set to Unit Codes 1, 2, 3, 4. But you can set it to control cameras set to 5, 6, 7, 8, or 9, 10, 11, 12, or 13, 14, 15, 16. Program SCAN SweepCentre Normal A C E G I K M O . . . . .. . . CAMERA C1 C3 C2 C4 POSITION P1P2 P4P3 Set to the same letter as the TM751 and cameras. Scans forward or backward thru cameras controlled by C1 thru C4. “Pans” left and right. “Tilts” up and down. Write locations of cameras here. Controls 4 cameras. Stores the positions for 4 cameras. F.C.C. CAUTION - THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TO THE UNITS. ANY CHANGES MADE TO THE UNITS WILL VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. LIMITED 1-YEAR WARRANTY Please visit www.x10.com/warranty to complete your on-line warranty registration. Thank you. For help or more information on setup, please visit: www.x10.com/support Centers each camera position. Sweeps thru the 4 stored positions for the selected camera.

310MHz Transmitter MPU (EM78P156BP) 310MHz Block Diagram for CR14A Remote Key Matrix

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. NO SERVICEABLE PARTS INSIDE. Use Four AAA alkaline batteries. For use with X10 Transceivers, Modules, and Remote Controlled Cameras. www.x10.com/support FCC ID: B4SCR14A MADE IN CHINA Camera Pan and Tilt Remote Control Model CR14A CR14A Rating label 2:1 08/20/01

To clear all stored positions: Press and hold Center then flip the switch at the bottom to Program and back. Pan ‘n Tilt Remote For use with X10 wireless cameras Model CM14A CM14A-8/01 1. Install 4 AAA alkaline batteries (sold separately) in the remote’s battery compartment. 2. Use a dime to set the Housecode dial to match the cameras, and transceiver you want to use the remote with. 3. Plug in an X10 Transceiver (RR501 or TM751, sold separately). Set Housecode to match remote. Fully extend the antenna. 4. To control up to 4 Cameras, attach each one to a ZC15A Pan and Tilt base (sold separately), plug each ZC15A into its own Addressable Power Supply, and set each power supply to the same Housecode you used in steps 2 and 3. Set each power supply to a unique number between 1 and 4. Pressing any Camera button (C1, C2, C3, or C4) turns on that camera (1, 2, 3, or 4) and turns the others (in the group) off. Then, each press of either the or button turns on the next or previous camera in the group of 4 while turning the current camera off. (You set all cameras to the same channel as the Video Receiver connected to your TV (Channel A, B, C, D). 5. After you press the "C" button to turn on a camera, pressing a left or right BLUE button at the top “pans” the camera left or right. Pressing a BLUE up or down button “tilts” the camera up or down. 6. To make buttons C1 thru C4 control cameras 5-8 (instead of 1 thru 4) press (and hold) the C2 button then flip the switch at the bottom from Normal to Program and back. Buttons C1, C2, C3, and C4 now control cameras set to 5, 6, 7, and 8. 7. Pressing C3 in step 6 sets buttons C1, C2, C3, and C4 to control cameras set to 9, 10, 11, and 12. 8. Pressing C4 in step 6 sets buttons C1, C2, C3, and C4 to control cameras set to 13, 14, 15, and 16. Buttons P1 thru P4 are used to store 4 position settings for each of the 4 cameras controlled by buttons C1 thru C4. 1. To store the first position for the camera controlled by C1, press C1. 2. Press the blue buttons to scan to the position you want. 3. Press and hold P1, then flip the switch at the bottom from Normal to Program and back, to store that position under P1. 4. Repeat steps 2 and 3, pressing P2 to store another position under P2. 5. Repeat for P3, and P4. Repeat steps 1 thru 4 to store 4 positions for C2, C3, and C4. Press the “C” button for any camera, following by any “P” button to move to the position stored under that button for that camera. Press the “C” button then Sweep to sweep through all 4 positions stored for that camera. Press the “C” button then Center to center the position for that camera. Installation and operating instructions The CR14A Remote lets you turn on any of 4 cameras or scan each of them in turn (forward or backward) so as to display the image from each camera in turn on your TV. If you purchase a Camera Pan and Tilt base (model ZC15A) for each camera, you can also use the remote to move the position of the camera from left to right (Pan) and up and down (Tilt). The Remote sends Wireless Radio Frequency (RF) signals to an X10 Transceiver (RR501 or TM751). The Transceiver then passes the signals onto your house wiring to control Wireless Cameras around your home. You connect each camera (up to 4) to a ZC15A base and plug each ZC15A into Addressable Power Supplies each set to a different number. The CR14A normally controls Cameras set to Unit Codes 1, 2, 3, 4. But you can set it to control cameras set to 5, 6, 7, 8, or 9, 10, 11, 12, or 13, 14, 15, 16. Program SCAN SweepCentre Normal A C E G I K M O . . . . .. . . CAMERA C1 C3 C2 C4 POSITION P1P2 P4P3 Set to the same letter as the TM751 and cameras. Scans forward or backward thru cameras controlled by C1 thru C4. “Pans” left and right. “Tilts” up and down. Write locations of cameras here. Controls 4 cameras. Stores the positions for 4 cameras. F.C.C. CAUTION - THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TO THE UNITS. ANY CHANGES MADE TO THE UNITS WILL VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. LIMITED 1-YEAR WARRANTY Please visit www.x10.com/warranty to complete your on-line warranty registration. Thank you. For help or more information on setup, please visit: www.x10.com/support Centers each camera position. Sweeps thru the 4 stored positions for the selected camera.



Test Report No. R-9144-1 FCC ID: B4SCR14 APPLICANT X-10 (USA), Inc. 400 Forge Way, Suite 412 Rockaway, NJ 07866-2033 MANUFACTURER X-10 Electronics Shenzhen Co. Ltd. X-10 Building Labour Industrial District Shenzhen, Xixiang, Bao An Guang Dong, China, 518102 TEST SPECIFICATION:FCC Rules and Regulations Part 15, Subpart C, Para. 15.231 TEST PROCEDURE:ANSI C63.4:1992 TEST SAMP LE DESCRIP TION BRANDNAME: X-10 (USA), Inc. MODEL: CR14A TYPE: Pulsed Transmitter POWER REQUIREMENTS: 6 VDC derived from (4) new “AAA” Batteries FREQUENCY OF OPERATION: 310 MHz TESTS P ERFORMED Para. 15.231(b)(1), Radiated Emissions, Fundamental and Harmonics Para. 15.231(c), Radiated Emissions, Spurious Case Para. 15.35, Duty Cycle Determination Para. 15.231(c), Occupied Bandwidth REPORT OF MEASUREMENTS Applicant: X-10 (USA), Inc. Device:Pulsed Transmitter FCC ID: B4SCR14A Power Requirements: 6 VDC derived from (4) new “AAA” Batteries Applicable Rule Section:Part 15, Subpart C, Section 15.231 Test Report No. R-9144-1 FCC ID: B4SCR14 REPORT OF MEASUREMENTS (continued) TEST RESULTS 15.231 (a):This device is used as a remote control transmitter. 15.231 (a)(1) &The transmitter is manually operated and ceases transmission within 5 15.231(a)(2):seconds after deactivation. 15.231 (a)(3):The transmitter does not perform periodic transmissions. 15.231 (b):The fundamental field strength did not exceed 5833 μV/M (Average) at a test distance of 3 meters. In addition, the requirements of section 15.35 for averaging pulsed emissions and for limiting peak emissions were met. The field strength of harmonic and spurious emissions did not exceed 583 μV/M (AVERAGE). DETERMINATION OF FIELD STRENGTH LIMITS The field strength limits shown below are found in Section 15.231. Frequency Limit F1=2603750 =L1 Fo=312Lo F2=47012500 =L2 The formula below was utilized to determine the limits: Limit = L1 + [(Fo-F1)(L2-L1)/(F2-F1)] Solving yields: Fundamental Limit= 5833 μV/M (AVERAGE) @ 3 Meters Harmonic Limit= 583 μV/M (AVERAGE) @ 3 Meters Test Report No. R-9144-1 FCC ID: B4SCR14 REPORT OF MEASUREMENTS (continued) DUTY CYCLE DETERMINATION The unit’s RF output was directly coupled to the input of the spectrum analyzer. The analyzer was set for a frequency span of 0Hz. The sweep time was then adjusted in order to display one full pulse train. The transmitter on time was then summed and compared to the time for one full cycle in order to obtain the duty cycle.( See plots for additional information) Transmitter On Time=28.8 milliseconds (maximum- worst case in 100 ms) Transmitter Cycle Time=>100 Transmitter Duty Cycle=28.8 % CALCULATION: 1 Large Pulse = 9.0 milliseconds 33 x 600 μs (small pulse)= 19.8 milliseconds 10.5 + 19.8= 28.8 milliseconds Duty Cycle=28.8 % Correction Factor = 20 log(0.288) =-10.8 SPECTRUM ANALYZER DESENSITIZATION CONSIDERATIONS Due to the nature of the emissions being measured, care was taken to ensure that the resolution bandwidth of the spectrum analyzer was adequate to provide accurate measurements. The following formula was utilized: Setting pulse desensitization equal to zero and utilizing the minimum observed pulse width of 600μs yields a minimum required bandwidth of 1.11 kHz. FCC specified bandwidths of 100kHz and 1MHz were utilized below and above 1GHz, respectively. Test Report No. R-9144-1 FCC ID: B4SCR14 GENERAL NOTES 1. All readings were taken utilizing a peak detector function at a test distance of 3 meters. 2. The duty cycle was applied to the peak readings in order to determine the average value of the emissions. 3. The frequency range was scanned from 30 MHz to 3.1 GHz. All emissions not reported were more than 20 dB below the specified limit. Test Report No. R-9144-1 FCC ID: B4SCR14 EQUIPMENT LIST FCC15.231 Compliance Testing ENTypeManufacture rDe scriptionMode l No.Cal Date Due Date 067Open Area Test SiteRetlif3 MeterRNY9/20/009/20/03 128CDouble Ridge GuideEaton Corporation1 GHz - 18 GHz960019/18/009/18/01 133Broadband Pre-AmplifierElectro-Metrics10 kHz - 1 GHz, 26dBBPA-10006/13/016/13/02 141Spectrum AnalyzerHewlett Packard100 Hz - 40 GHz8566B7/2/011/2/02 141AGraphics PlotterHewlett PackardN/A7470A3/5/013/5/02 141BQuasi-Peak AdaptorHewlett Packard100 Hz - 1 GHz85650A2/20/011/2/02 523BiconilogElectro-Mechanics26 - 2000 MHz3142B6/8/009/8/01 543PreamplifierHewlett Packard1.0 GHz - 26.5 GHz8449B6/27/016/27/02 617Interference AnalyzerElectro-Metrics10 kHz - 1 GHzEMC-302/27/012/27/02 Test Report No. R-9144-1 FCC ID: B4SCR14A FCC 15.231(b) and FCC 15.231(c) RADIATED EMISSIONS, FUNDAMENTAL & SPURIOUS CASE See separate e-file attachment named REfundharm.pdf and REspur.pdf FCC 15.231(c) OCCUPIED BANDWIDTH Please refer to separate electronic file named Occbw.pdf Test Report No. R-9144-1 FCC ID: B4SCR14A FCC 15.35 DUTY CYCLE Please refer to separate electronic file named Dutycycle.pdf Test Report No. R-9144-1 FCC ID: B4SCR14A Test Setup Photograph Test Report No. R-9144-1 FCC ID: B4SCR14A

Retlif Testing Laboratories R Data Sheet 1 of 4 Test Method: FCC Part 15 Subpart C Radiated Emissions, Fundamental & Harmonic Emissions Customer: X-10 (USA) Job No. R-9144-1 Test Sample: RF remote Paragraph: 15.231 Model No.: CR14A FCC ID: B4SCR14A Operating Mode: Continuously Transmitting a 310 MHz Signal Technician: Peter Lananna Date: August 23, 2001 Notes: Test Distance: 3 Meters Detector: Peak, Unless otherwise specified Test Freq. Antenna Pol./Height EUT Orientation Meter Reading Correction Factor Corrected Reading Converted Reading Peak Limit MHz (V/H)/Meters X / Y / Z dBuV dB dBuV/m uV/m uV/m 310 H / 2.3 X 69.6 -4.0 65.6 1905.5 58300 | H / 1.0 Y 77.3 -4.0 73.3 4623.8 | | H / 1.8 Z 72.0 -4.0 68.0 2511.9 | | V / 2.0 X 75.0 -4.0 71.0 3548.1 | | V / 1.0 Y 63.7 -4.0 59.7 966.1 | 310 V / 1.5 Z 74.1 -4.0 70.1 3198.9 58300 620 H / 1.0 X 48.2 3.9 52.1 402.7 5830 | H / 1.0 Y 50.0 3.9 53.9 495.5 | | H / 1.5 Z 48.4 3.9 52.3 412.1 | | V / 2.3 X 47.3 3.9 51.2 363.1 | | V / 2.3 Y 45.6 3.9 49.5 298.5 | 620 V / 2.3 Z 46.6 3.9 50.5 335.0 5830 930 H / 2.0 X 35.6 8.8 44.4 166.0 5830 | H / 1.3 Y 39.7 8.8 48.5 266.1 | | H / 1.5 Z 37.7 8.8 46.5 211.3 | | V / 1.0 X 46.6 8.8 55.4 588.8 | | V / 1.5 Y 38.0 8.8 46.8 218.8 | 930 V / 1.5 Z 41.9 8.8 50.7 342.8 5830 1240 H / 1.0 X 41.7 -2.8 38.9 88.1* 5000 | H / 1.0 Y 41.7 -2.8 38.9 88.1* | | H / 1.0 Z 41.7 -2.8 38.9 88.1* | | V /1.0 X 41.7 -2.8 38.9 88.1* | | V / 1.0 Y 41.7 -2.8 38.9 88.1* | 1240 V / 1.0 Z 41.7 -2.8 38.9 88.1* 5000 1550 H / 1.0 X 39.7 0.9 40.6 107.2* 5000 | H / 1.0 Y 39.7 0.9 40.6 107.2* | | H / 1.0 Z 39.7 0.9 40.6 107.2* | | V /1.0 X 39.7 0.9 40.6 107.2* | | V / 1.0 Y 39.7 0.9 40.6 107.2* | 1550 V / 1.0 Z 39.7 0.9 40.6 107.2* 5000 The frequency range was scanned from 30 MHz to 3.1 GHz. All emissions not recorded were more Than 10 dB below the specified limit. Emissions from the EUT do not exceed the specified limits. *=Noise Floor Measurements (Minimum system sensitivity) Retlif Job Number R-9144-1 Retlif Testing Laboratories R Data Sheet 2 of 4 Test Method: FCC Part 15 Subpart C Radiated Emissions, Fundamental & Harmonic Emissions Customer: X-10 (USA) Job No. R-9144-1 Test Sample: RF remote Paragraph: 15.231 Model No.: CR14A FCC ID: B4SCR14A Operating Mode: Continuously Transmitting a 310 MHz Signal Technician: Peter Lananna Date: August 23, 2001 Notes: Test Distance: 3 Meters Detector: Peak, unless otherwise specified Test Freq. Antenna Pol./Height EUT Orientation Meter Reading Correction Factor Corrected Reading Converted Reading Peak Limit MHz (V/H)-Meters X / Y / Z dBuV dB dBuV/m uV/m uV/m 1860 H / 1.0 X 38.7 3.0 41.7 121.6* 5830 | H / 1.0 Y 38.7 3.0 41.7 121.6* | | H / 1.0 Z 38.7 3.0 41.7 121.6* | | V /1.0 X 38.7 3.0 41.7 121.6* | | V / 1.0 Y 38.7 3.0 41.7 121.6* | 1860 V / 1.0 Z 38.7 3.0 41.7 121.6* 5830 2170 H / 1.0 X 39.2 0.4 39.6 95.5* 5830 | H / 1.0 Y 39.2 0.4 39.6 95.5* | | H / 1.0 Z 39.2 0.4 39.6 95.5* | | V /1.0 X 39.2 0.4 39.6 95.5* | | V / 1.0 Y 39.2 0.4 39.6 95.5* | 2170 V / 1.0 Z 39.2 0.4 39.6 95.5* 5830 2480 H / 1.0 X 39.7 3.8 43.5 149.6* 5830 | H / 1.0 Y 39.7 3.8 43.5 149.6* | | H / 1.0 Z 39.7 3.8 43.5 149.6* | | V /1.0 X 39.7 3.8 43.5 149.6* | | V / 1.0 Y 39.7 3.8 43.5 149.6* | 2480 V / 1.0 Z 39.7 3.8 43.5 149.6* 5830 2790 H / 1.0 X 38.2 5.8 44.0 158.5* 5000 | H / 1.0 Y 38.2 5.8 44.0 158.5* | | H / 1.0 Z 38.2 5.8 44.0 158.5* | | V /1.0 X 38.2 5.8 44.0 158.5* | | V / 1.0 Y 38.2 5.8 44.0 158.5* | 2790 V / 1.0 Z 38.2 5.8 44.0 158.5* 5000 3100 H / 1.0 X 40.0 6.4 46.4 208.9* 5830 | H / 1.0 Y 40.0 6.4 46.4 208.9* | | H / 1.0 Z 40.0 6.4 46.4 208.9* | | V /1.0 X 40.0 6.4 46.4 208.9* | | V / 1.0 Y 40.0 6.4 46.4 208.9* | 3100 V / 1.0 Z 40.0 6.4 46.4 208.9* 5830 The frequency range was scanned from 30 MHz to 3.1 GHz. All emissions not recorded were more Than 10 dB below the specified limit. Emissions from the EUT do not exceed the specified limits. *=Noise Floor Measurements ( Minimum system sensitivity) Retlif Job Number R-9144-1 Retlif Testing Laboratories R Data Sheet 3 of 4 Test Method: FCC Part 15 Subpart C Radiated Emissions, Fundamental & Harmonic Emissions Customer: X-10 (USA) Job No. R-9144-1 Test Sample: RF remote Paragraph: 15.231 Model No.: CR14A FCC ID: B4SCR14A Operating Mode: Continuously Transmitting a 310 MHz Signal Technician: Peter Lananna Date: August 23, 2001 Notes: Test Distance: 3 Meters Duty Cycle: 22.8 % Detector: Peak, unless otherwise specified Duty Cycle Correction: -10.8dB Test Freq. Antenna Pol./Height EUT Orientation Peak Reading Correction Factor Corrected Reading Converted Reading Avg. Limit MHz (V/H)-Meters X / Y / Z dBuV dB dBuV/m uV/m uV/m 310 H / 2.3 X 65.6 -10.8 54.8 549.5 5830 | H / 1.0 Y 73.3 -10.8 62.5 1333.5 | | H / 1.8 Z 68.0 -10.8 57.2 724.4 | | V / 2.0 X 71.0 -10.8 60.2 1023.3 | | V / 1.0 Y 59.7 -10.8 48.9 278.6 | 310 V / 1.5 Z 70.1 -10.8 59.3 922.6 5830 620 H / 1.0 X 52.1 -10.8 41.3 116.1 583 | H / 1.0 Y 53.9 -10.8 43.1 142.9 | | H / 1.5 Z 52.3 -10.8 41.5 118.9 | | V / 2.3 X 51.2 -10.8 40.4 104.7 | | V / 2.3 Y 49.5 -10.8 38.7 86.1 | 620 V / 2.3 Z 50.5 -10.8 39.7 96.6 583 930 H / 2.0 X 44.4 -10.8 33.6 47.9 583 | H / 1.3 Y 48.5 -10.8 37.7 76.7 | | H / 1.5 Z 46.5 -10.8 35.7 61.0 | | V / 1.0 X 55.4 -10.8 44.6 169.8 | | V / 1.5 Y 46.8 -10.8 36.0 63.1 | 930 V / 1.5 Z 50.7 -10.8 39.9 98.9 583 1240 H / 1.0 X 38.9 -10.8 28.1 25.4* 500 | H / 1.0 Y 38.9 -10.8 28.1 25.4* | | H / 1.0 Z 38.9 -10.8 28.1 25.4* | | V /1.0 X 38.9 -10.8 28.1 25.4* | | V / 1.0 Y 38.9 -10.8 28.1 25.4* | 1240 V / 1.0 Z 38.9 -10.8 28.1 25.4* 500 1550 H / 1.0 X 40.6 -10.8 29.8 30.9* 500 | H / 1.0 Y 40.6 -10.8 29.8 30.9* | | H / 1.0 Z 40.6 -10.8 29.8 30.9* | | V /1.0 X 40.6 -10.8 29.8 30.9* | | V / 1.0 Y 40.6 -10.8 29.8 30.9* | 1550 V / 1.0 Z 40.6 -10.8 29.8 30.9* 500 The frequency range was scanned from 30 MHz to 3.1 GHz. All emissions not recorded were more Than 10 dB below the specified limit. Emissions from the EUT do not exceed the specified limits. *=Noise Floor Measurements ( Minimum system sensitivity) Retlif Job Number …

Text truncated - open the document above for the full version.

Test Setup Photograph