B4SFWKRKey Chain Remote

INSTRUCTION MANUAL Cat. No. FWSK ONOFF 1 2 3 4 6 7 5 9 8 10 12 11 13 15 16 14 ROOM COLOR MOOD 2MOOD 1HOUSE ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF HH HH oo oo mm mm ee ee AA AA uu uu tt tt oo oo mm mm aa aa tt tt ii ii oo oo nn nn SS SS tt tt aa aa rr rr tt tt ee ee rr rr KK KK ii ii tt tt Indoor Remote Catalog # FWIR Messenger Hub Catalog # FWMH Lamp Receiver Catalog # FWLR Key Chain Remote Catalog # FWKR Bulb Receiver Catalog # FWBR Home Auto Manual large NEWEST 4/24/03 3:40 PM Page 1 General Safety Rules WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS CAUTION:To reduce the risk of electric shock, do not disassemble any parts. No user-serviceable parts are inside. If you spill liquid on a unit, disconnect the unit from the AC outlet to prevent possible fire or shock hazard and consult authorized service personnel. WARNING:To prevent electric shock hazard, do not expose any part to rain or moisture. WARNING:Use only incandescent bulbs in lamps that are to be controlled by Lamp Receivers. Using any other type bulbs could damage bulbs and or Lamp Receivers. Attempting to control any other device by the Lamp Receivers, may damage that device and may damage the Lamp Receiver. FCC Caution THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAYCAUSE UNDESIRED OPERATION. This equipment generates and uses radio frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturers instructions, it may cause interference to radio and television reception. It has been type tested and found to comply with the limits for remote control devices in accordance with the specifications in Sub Parts B and C of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by unplugging the equipment, try to correct the interference by one or more of the following measures. • Reorient the antenna of the radio/TV experiencing the interference. • Relocate the interference with respect to the radio/TV. • Move the interference away from the radio/TV. • Plug the interface into an outlet on a different electrical circuit from the radio/TV experiencing the interference. • If necessary, consult your local Dealer for additional suggestions NOTE: Modifications to any of the components in this kit will void the user’s authority to operate this equipment. 2 Home Auto Manual large NEWEST 4/24/03 3:40 PM Page 2 3 ONOFF 1 2 3 4 6 7 5 9 8 10 12 11 13 15 16 14 ROOM COLOR MOOD 2MOOD 1HOUSE ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF INDOOR REMOTE LAMP RECEIVER BULB RECEIVER MESSENGER HUB KEY CHAIN REMOTE The MESSENGER HUB is the brainof the Freewire tm system. When it is plugged into an AC outlet it has the ability to receive Radio Frequency (RF) signals from the remotes and the ability to send messages through existing house wiring to all receivers that are dialed to the same house code. It is also used to control *incandescent lamps only , rated up to 500 watts, connected to the plug receptacle at the bottom of the MESSENGER HUB. Note:For restrictions and instructions see MESSENGER HUB section. *Do not use fluorescent, low wattage, energy saving and halogen bulbs. The INDOOR REMOTE sends Radio Frequency (RF) signals to the MESSENGER HUB. These signals can go through walls, so you can use this remote to control lights (or appliances with approved appliance receiver only) from anywhere in or around your home. NOTE: Walls and other obstructions may reduce the effective range of the RF signal. A LAMP RECEIVER must be used in conjunction with at least one active MESSENGER HUB. It is used to control *incandescent lamps only rated up to 300 watts. Note:For restrictions and instructions see LAMP RECEIVER section. *Do not use fluorescent, low wattage, energy saving and halogen bulbs. The BULB RECEIVER must be used in conjunction with at least one MESSENGER HUB. It is used to control an indoor or outdoor incandescent light (up to 150 watts) that is normally controlled by a wall switch. *Do not use fluorescent, low wattage, energy saving and halogen bulbs. The KEY CHAIN REMOTE can conveniently turn on and off a limited number of lights which you select from the MESSENGER HUB. NOTE:For restrictions and instructions see KEY CHAIN REMOTE section Getting familiar with your home automation kit. Home Auto Manual large NEWEST 4/24/03 3:40 PM Page 3 4 PLEASE FOLLOW THE SEQUENCE LAID OUT IN THIS MANUAL TO AVOID CONFUSION Step by step instructions to set up the MESSENGER HUB: A Quick Note Before You Set Up MESSENGER HUB: WARNING: For indoor use only. Each receiver has a specific address made up of a HOUSE CODE (bottom dial) and a Unit Code (upper dial) which is used to communicate with the MESSENGER HUB. The function of the HOUSE CODE is to prevent interference from another FREEWIRE system. If at any time, you experience interference with another system please choose another setting for your HOUSE CODE A - P. The letter selected must be the same on all RECEIVERS and the MESSENGER HUB. Step 1: Plug MESSENGER HUB into any operational AC outlet within your home. Rotate antenna to the upright position. Open the front door to expose control panel as shown in Figure 1. NOTE: Placing the MESSENGER HUB on the inside wall closest to driveway or entry way, will often maximize range of the KEY CHAIN REMOTE. Step 2: Select a HOUSE CODE on the MESSENGER HUB, any letterA- P. (Note:The house code you select for the MESSENGER HUB will d…

Text truncated - open the document above for the full version.

MCU 12C508A Block Diagram for FWKR RF REMOTE Key Matrix 418MHzTransmitter 418MHz

B&D Keychain Remote (KR30A) rating label 2:1 4/28/03 For use with Freewire ™ remote receivers and modules. Use two CR2016 Lithium 3V batteries. No serviceable parts inside. Keychain Remote FWKR FCC ID: B4SFWKR www.blackanddecker.com Made in China

MODEL FWKR Operational Description The MODEL FWKR is a 418 MHz pulsed RF transmitter remote control. The RF remote is used in conjunction with the Messenger Hub RF receiver. The remote can activate various household appliances when used with the RF receiver that is connected to the household AC wiring. The remote control’s internal MCUs receive information from the keypad and convert the keystrokes into a pulse code. The pulse code is then sent to the 418 MHz RF transmitter and is used to pulse modulate the 418 MHz carrier.

LEVEL PART IDENTIFIER DESCRIPTIONQTY/ASSY REFERENCE 0 FWKRSEC KEYCHAIN REMOTE NPACK1 1 038010H10513-1LABEL-FREQUENCE (418MC)1 1 038010H11093PLAIN WHITE LABEL(20X5)MM1 1 038020H12138RATING LABEL FWKR1 1 098-30080013LITHIUM BATT. 3V (CR2016)2 1 185000H16345TOP CABINET BLACK1 1 185000H16350ABOTTOM CABINET (REV.A)1 1 275000H10635RUBBER KEYPAD1 1 851001H11218PCB ASSY (6V)1 0.2 038010H10513-1LABEL-FREQUENCE (418MC)1 0.2 038010H11093PLAIN WHITE LABEL(20X5)MM1 0.2 042010H10677BPCB1 0.2 076-10400016CAP-MCC 100N +8-2 Y5V08051 C7 0.2 076-15000002CAP-MCC 15P 5% NPO 08051 C3 076-18900000CAP-MCC 1P8 .25P NPO 08051 C8 0.2 076-50900002 CAP-MCC 5P 5% NPO 08051 C2 0.2 076-60900000CAP-MCC 6P .25P NPO 08051 C1 0.2 080001H10021SAW 418MHZ SIEMENS1 Y1 0.2 160-56700006INDUCTOR 56NH 5% 0805 SMD1 L1 0.2 162089H10013RF WIRE LOOP ID=4 WD=0.61 L2 0.2 209-00000003TRS-NPN 2SC3356 SMD1 Q1 0.2 211328H10145IC PIC12C508 SMD1 U1 0.2 220-00000000LED RED SMD 1.5X31 LED1 241-15300000RES-TFC 15K 5% 1/10W 08051 R2 0.2 241-68000000 RES-TFC 68R 5% 1/10W 08051 R1 0.2 241-68100000RES-TFC 680R 5% 1/10W08051 R4 0.2 241-68200000RES-TFC 6K8 5% 1/10W 08051 R3 0.2 241-68300000RES-TFC 68K 5% 1/10W 08051 R5 241-68400000RES-TFC 680K 5% 1/10W08051 0.2 403021H10450A CONTACT PLATE (+VE)1 0.2 403021H10451CONTACT PLATE (-)1

1 2 3 4 5 6 78 ABCD 8 7 6 5 4 3 2 1 D CBA Title Number Revision Size A3 Date: 28-Apr-2003 Sheet of File: A:\B&D_KF1.SCH Drawn By: KEY44/2KEY07/2KEY26/2 KEY 36/3KEY17/3KEY54/3 LED1 R4 680R R2 15K R36K8 R1 300R Y1 418MHz Q13356 C16P C25P C4 * C3 15P PCB TRACE L1 56N +6V BAT1 2 X 2032 1 ON 1 OFF MOOD1 OFF MOOD1 ONHOUSE ON HOUSE OFF Black & Decker Keyfob Remote 01 C7 100N 6mm L2 +6V 851001H11218 R5 68K R6680K VDD 1 GP5 2 GP4 3 GP3 4 GP2 5 GP1 6 GP0 7 VSS 8 U1 PIC12C508 RFO RFO C8 1P8

Test Report No. R-9895-1 FCC ID: B4SFWKR APPLICANT X-10 USA, Inc. 19823, 58 th Place S. Kent, WA 98032 MANUFACTURER X-10 Electronics Shenzhen Co. Ltd. X-10 Building Labour Industrial District Shenzhen, Xixiang, Bao An Guang Dong, China, 518102 TEST SPECIFICATION: FCC Rules and Regulations Part 15, Subpart C, Para. 15.231 TEST PROCEDURE: ANSI C63.4:2000 TEST SAMPLE DESCRIPTION BRANDNAME: Black & Decker MODEL: FWKR TYPE: Pulsed Transmitter POWER REQUIREMENTS: 6 VDC derived from (2) 3 volt Lithium Batteries, Model No. CR2016 FREQUENCY OF OPERATION: 418 MHz TESTS PERFORMED Para. 15.231(b), Radiated Emissions, Fundamental and Harmonics Para. 15.231(b), Radiated Emissions, Spurious Case Para. 15.35, Duty Cycle Determination Para. 15.231(c), Occupied Bandwidth Test Report No. R-9895-1 FCC ID: B4SFWKR REPORT OF MEASUREMENTS Applicant: X-10 (USA), Inc. Device: Pulsed Transmitter FCC ID: B4SFWKR Power Requirements: 6 VDC derived from (2) 3 volt Lithium Batteries, Model No. CR2016 Applicable Rule Section: Part 15, Subpart C, Section 15.231 TEST RESULTS 15.231 (a): This device is used as a remote control transmitter. 15.231 (a)(1) & The transmitter is manually operated and ceases transmission within 5 15.231(a)(2): seconds after deactivation. 15.231 (a)(3): The transmitter does not perform periodic transmissions. 15.231 (b): The fundamental field strength did not exceed 10,330 μV/M (Average) at a test distance of 3 meters. In addition, the requirements of section 15.35 for averaging pulsed emissions and for limiting peak emissions were met. The field strength of harmonic and spurious emissions did not exceed 1,033 μV/M (AVERAGE). DETERMINATION OF FIELD STRENGTH LIMITS The field strength limits shown below are found in Section 15.231. Frequency Limit F1 = 260 3750 = L1 Fo = 418 Lo F2 = 470 12500 = L2 Test Report No. R-9895-1 FCC ID: B4SFWKR REPORT OF MEASUREMENTS (continued) The formula below was utilized to determine the limits: Limit = L1 + [(Fo-F1)(L2-L1)/(F2-F1)] Solving yields: Fundamental Limit = 10,330 μV/M (AVERAGE) @ 3 Meters Harmonic Limit = 1,033 μV/M (AVERAGE) @ 3 Meters DUTY CYCLE DETERMINATION The unit’s RF output was directly coupled to the input of the spectrum analyzer. The analyzer was set for a frequency span of 0Hz. The sweep time was then adjusted in order to display one full pulse train. The transmitter on time was then summed and compared to the time for one full cycle in order to obtain the duty cycle. Transmitter On Time = 37.4 milliseconds (maximum) Transmitter Cycle Time = >100 milliseconds Transmitter Duty Cycle = 37.4 % See separate e-file plots named dutycycle.pdf for additional information. Test Report No. R-9895-1 FCC ID: B4SFWKR SPECTRUM ANALYZER DESENSITIZATION CONSIDERATIONS Due to the nature of the emissions being measured, care was taken to ensure that the resolution bandwidth of the spectrum analyzer was adequate to provide accurate measurements. The following formula was utilized: Setting pulse desensitization equal to zero and utilizing the minimum observed pulse width of 550.0 μs yields a minimum required bandwidth of 1.212 kHz. FCC specified bandwidths of 100kHz and 1MHz were utilized below and above 1GHz, respectively. GENERAL NOTES All readings were taken utilizing a peak detector function at a test distance of 3 meters. The duty cycle was applied to the peak readings in order to determine the average value of the emissions. The frequency range was scanned from 30 MHz to 4.18 GHz. All emissions not reported were more than 20 dB below the specified limit. Test Report No. R-9895-1 FCC ID: B4SFWKR EQUIPMENT LIST FCC Part 15 Subpart C Radiated Emissions EN Type Manufacturer Description Model No. Cal Date Due Date 067 Open Area Test Site Retlif 3 Meter RNY 09/20/2000 09/20/2003 128 Double Ridged Guide Electro-Mechanics 1 GHz - 18 GHz 3105 06/07/2002 06/07/2003 133 Broadband Pre-Amplifier Electro-Metrics 10 kHz - 1 GHz, 26dB BPA-1000 06/11/2002 06/11/2003 141 Spectrum Analyzer Hewlett Packard 100 Hz - 40 GHz 8566B 01/23/2003 07/23/2003 141A Graphics Plotter Hewlett Packard N/A 7470A 03/05/2003 03/05/2004 141B Quasi-Peak Adaptor Hewlett Packard 100 Hz - 1 GHz 85650A 01/23/2003 07/23/2003 206B 6.0 dB Attenuator Texscan 0 - 1.0 GHz FP-50 - 6 dB 06/11/2002 06/11/2003 543 Preamplifier Hewlett Packard 1.0 GHz - 26.5 GHz 8449B 07/11/2002 07/11/2003 617 Interference Analyzer Electro-Metrics 10 kHz - 1 GHz EMC-30 08/23/2002 08/23/2003 767 Biconilog EMCO 26 - 2000 MHz 3142B 09/03/2002 09/03/2003 Test Report No. R-9895-1 FCC ID: B4SFWKR FCC 15.231(b) RADIATED EMISSIONS, FUNDAMENTAL & SPURIOUS CASE (See separate e-file named Refundharm & REspur.pdf) FCC 15.231(c) OCCUPIED BANDWIDTH (See separate e-file named occbw.pdf) Test Report No. R-9895-1 FCC ID: B4SFWKR FCC 15.231(c) DUTY CYCLE (See separate e-file named dutycycle.pdf) Test Report No. R-9895-1 FCC ID: B4SFWKR Test Setup Photographs

Test Setup Photographs

Test Setup Photographs