B4SPH750TUNIVERSAL REMOTE

PH750 Owner’s Manual 32 Introduction Table of Contents Congratulations on your purchase of a Philips Universal Remote Control. Philips Universal Remotes let you replace a broken or lost remote or combine more than one remote into one. In addition, this remote is equipped with a command learning feature which lets the remote learn commands from your original equipment remote control! This remote control operates the common features of most but not all models and brands of IR Infrared Controlled Video Equipment. This remote may provide functions that are not available on your equipment. Some functions of your particular equipment (e.g. menu functions) may not be controlled by this remote. In such cases, use the original remote control for your equipment. Please use this manual to become familiar with your Philips Universal Remote. After you are familiar with your remote the first thing you need to do is to install batteries and setup your remote for your particular product and brand. The remote also transmits wireless radio Frequency (RF) com- mands. The wireless receiver (included), see page 21, or a video sender (sold separately) receives these commands and converts them to regular Infrared (IR) commands. These IR commands are then emitted from the IR Extender to control your A/V components. This lets you control your A/V components from ANY room in your home - you don’t need to aim the remote at your component! Thank you for buying a Philips remote and we hope it will give you many years of service. FCC Caution THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDI- TIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTER- FERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTER- FERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. This equipment generates and uses radio frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturers instructions, it may cause interference to radio and television reception. It has been type tested and found to comply with the limits for remote control devices in accordance with the specifications in Sub-Parts B and C of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by unplugging the equipment, try to correct the interference by one or more of the following measures. • Reorient the antenna of the radio/TV experiencing the interference. • Relocate the receiver with respect to the radio/TV. • Move the receiver away from the radio/TV. • Plug the receiver into an outlet on a different electrical circuit from the radio/TV experiencing the interference. • If necessary, consult your local Dealer for additional suggestions. NOTE: Modifications to any of the components in this kit will void the user’s authority to operate this equipment. Introduction.................................................................... 2 Setup............................................................................. 4 Battery Installation..................................................... 4 Battery Saver............................................................. 4 Code Saver ............................................................... 4 Power-On default...................................................... 5 TV Punch Through Feature........................................ 5 VCR Punch Through Feature..................................... 5 Code Setup ............................................................... 5 Button Functions............................................................. 6 Advanced DVD and SAT Button Functions..................... 8 VCR/DVD Punch-Through Feature................................ 9 TV/VCR and TV/DVD Combo units.............................. 9 Code Entry................................................................... 10 Direct Code Entry.................................................... 10 Code Search ........................................................... 11 Code Search by Brand............................................ 12 Code Identification................................................... 14 Sleep Timer.................................................................. 15 Code Learning.............................................................. 16 Tips on Learning...................................................... 16 Learning Commands................................................ 17 Clearing Learned commands for a mode................... 18 Master Clear........................................................... 19 Product Operation........................................................ 20 Wireless Receiver......................................................... 21 Troubleshooting............................................................ 22 54 CODE SEARCH Setup Setup, cont. Code Saver Codes are stored in permanent memory while you are changing batteries so you will not lose any codes stored in the remote while you are changing batteries. Power-On Default The remote powers on in TV mode. TV Volume/Mute Punch-Through Feature The TV Volume/Mute punch-through feature lets you control the Volume and Mute function of your TV in any mode programmed to be a VCR, DVD, CABLE or SAT device, without needing to change to TV mode. VCR/DVD Punch-Through Feature Punch-through to VCR/DVD mode i.e. the 6 keys (PLAY, PAUSE, STOP, FF, REWIND, and REC) is only allowed in modes pro- grammed for TV or Cable codes. Battery Installation 1. On the back of the remote, push down on the tab and lift the cover off. 2. Match the batteries to the + and - marks inside the battery case, then insert 2 AAA Alkaline batteries. 3. Press the battery cover back into place. Batter…

Text truncated - open the document above for the full version.

IR Driver MCU Block Diagram for PH750T RF Remote Key Matrix 418MHz Transmitter 418MHz

Retlif Testing Laboratories, Test Report R-10698-1, X-10(USA), FCC ID B4SPH750T Page 1 of 3 Retlif Testing Laboratories, Test Report R-10698-1, X-10(USA), FCC ID B4SPH750T Page 2 of 3

Retlif Testing Laboratories, Test Report R-10698-1, X-10(USA), FCC ID B4SPH750T Page 1 of 3

7 in 1 RF Universal Remote Use with ZN551R Receiver. Use two AAA alkaline batteries. 1. Press and hold CODE SEARCH until red light stays on. 2. Press and release mode button (TV, VCR, CBL, etc. 3. Enter 3 digit code from code list. FCC ID: B4SPH750T PH750T remote rating label 2: 1 12/13/04 Model PH750T Gemini Industries, Inc. Ledgewood, NJ 07852 Made in China

Retlif Testing Laboratories, Test Report R-10698-1, X-10(USA), FCC ID B4SPH750T Page 1 of 4 Retlif Testing Laboratories, Test Report R-10698-1, X-10(USA), FCC ID B4SPH750T Page 2 of 4 Retlif Testing Laboratories, Test Report R-10698-1, X-10(USA), FCC ID B4SPH750T Page 3 of 4 Retlif Testing Laboratories, Test Report R-10698-1, X-10(USA), FCC ID B4SPH750T Page 4 of 4

PH750T Operational Description The PH750T is a 418 MHz pulsed RF transmitter. The remote can control a variety of TVs, VCRs, DVDs, CDs, Satellite receivers and Cable boxes. The internal MCU receive information from the keypad and convert the keystrokes into a pulse code. The pulse code is then sent to the 418 MHz RF transmitter and is used to pulse modulate the 418 MHz carrier.

DCBA 12345678 ABCD 8 7 6 5 4 3 2 1 PICO ELECTRONICS Ltd., Eastfield Industrial Estate, Glenrothes, Fife, KY7 4NZ, SCOTLAND SHEET No. DATEDATE REVISION DATE FIRST DRAWN FILEDRNAPPD. DO NOT SCALE DRAWING TITLE: REV. Error : PICO.WMF File Not Found D:\SCH\PM725AD.SCH 11 of D GEMINI PM725A SERIES REMOTES PRINT DATE 10:04:41 13-Dec-2004 BKW 18/12/01 18/12/01 18/12/01 KEY13CAB13/3KEY19SAT13/4 KEY20CODESEARCH14/4KEY26INFO14/5KEY32PREV.CHAN14/6 KEY7VCR13/2KEY1TV13/1 KEY2MUTE14/1KEY8VOL.DOWN14/2KEY14VOL.UP14/3KEY50UP14/19 LED1 R2330R Y14MHZ R11M IR1 TR1 9013G VSS VSS 2 x AAA BATTERIES BATT1BATT2 C4 VSS OPTIONAL * VDD 11-7 26 D-0 11 D-1 12 11-6 25 11-5 24 C-1 35 C-0 34 TSTP_P 32 RSTP_N 29 SXI 31 SXO 30 D-7 18 D-6 17 D-5 16 D-4 15 D-3 14 D-2 13 10-1 2 10-0 1 10-3 4 10-2 3 10-5 6 10-4 5 10-7 8 10-6 7 11-1 20 11-0 19 11-3 22 11-2 21 C-3 37 VDD 33 C-2 36 FXI 28 FXO 27 GND 10 11-4 23 IR-OUT 9 U1 ROO8-USA KEY3CH.DOWN15/1KEY15RECORD15/3 KEY16STOP16/3 KEY17PAUSE17/3 KEY21115/4 KEY22216/4 KEY23317/4 KEY27415/5 KEY28516/5 KEY29617/5KEY35CC17/6 KEY39715/7 KEY41917/7KEY5CH.UP17/1 KEY9REWIND15/2 KEY10PLAY16/2 KEY11FF17/2 KEY4POWER16/1 KEY45TV/VCR15/8 KEY47ENTER17/8 KEY40816/7KEY46016/8 KEY51LEFT15/19 KEY53RIGHT17/19 KEY57MENU15/20 KEY59QUIT17/20 KEY58DOWN16/20 C3100NF VSS C2100UF6.3V R30R D11N4148 VSS NOTES:-1/ ALL UNSPECIFIED DIODES 1N4148 OR EQUIVALENT.2/ ALL UNSPECIFIED RESISTORS ARE 0.125W 5%.3/ ALL UNSPECIFIED CAPACITORS ARE AXIAL MLC TYPE."*" DENOTES COMPONENT NOT INSTALLED KEY55LEARN13/20 +3V TR59014D R947K R10470K R141K D7* VDD GATE FROM LED PORT C-2 IR INPUT SIGNAL C91UF10V A0 1 A1 2 A2 3 VSS 4 SDA 5 SCL 6 WP 7 VCC 8 U224LC16B VDD VSS TO LEARN CCT. GATE INPUT CLOCK DATA C1 100NF R410K (GEMINI) HE041 KEY36SLEEP18/6KEY66CHAPTER UP18/21KEY72CHAPTER DOWN18/22 KEY63PIP15/21KEY69TOGGLE15/22 KEY31AUX13/6KEY37DVD13/7KEY43CD13/8 (SCAN+) (SCAN-) (REPEAT) (SUBTITLE) KEY56GUIDE14/20 KEY52OK/SELECT16/19 A A B B OPTIONAL LEARN - SEE TABLE OPTIONAL LEARN - SEE TABLE LEARN CCT.REQUIRED MODELREMOTEPM725, PM725xWPM625, PM625xWPM525, PM525xWPM435/P/S, PM435xWPM430/G, PM430xW YESYESYESNONO PM720xW YES PM620xW YES PM520xW YES VSS SIGNAL ENABLE * N/A OPTIONAL RF DAUGHTER BOARD SHOWN FOR REFERENCE ONLY VSS V+ 1 2 34 ABCD 4 3 2 1 D CBA Title Number Revision Size A4 Date: 10-Dec-2004 Sheet of File: A:\RF418-TX.SCH Drawn By: TR1 H10 R1 10K R3 10K R2 270R C5 6P8 C322PC1 5P6 L2 6MM L3 18T L1 3.5T SAW1 418MHz RF INPUT +3V C4 1P RF 418MHz Tx 90MM ANT PCB TRACE

Retlif Testing Laboratories, Test Report R-10698-1, X-10(USA), FCC ID B4SPH750T Page 1 of 3 X-Axis, Front Y-Axis, Front Retlif Testing Laboratories, Test Report R-10698-1, X-10(USA), FCC ID B4SPH750T Page 2 of 3 Z-Axis, Front X-Axis, Rear Retlif Testing Laboratories, Test Report R-10698-1, X-10(USA), FCC ID B4SPH750T Page 3 of 3 Y-Axis, Rear Z-Axis, Rear

Retlif Testing Laboratories, Test Report R-10698-1, X-10(USA), FCC ID: B4SPH750T Page 1 of 18 APPLICANT X-10 USA, Inc. 19823, 58 th Place S. Kent, WA 98032 MANUFACTURER X-10 Electronics Shenzhen Co. Ltd. X-10 Building Labour Industrial District Shenzhen, Xixiang, Bao An Guang Dong, China, 518102 TEST SPECIFICATION: FCC Rules and Regulations Part 15, Subpart C, Para. 15.231 TEST PROCEDURE: ANSI C63.4:2003 TEST SAMPLE DESCRIPTION BRANDNAME: X10 MODEL: PH750T TYPE: Pulsed Transmitter POWER REQUIREMENTS: 3 VDC via two (2) “AAA” batteries FREQUENCY OF OPERATION: 418 MHz TESTS PERFORMED Para. 15.231(a), Radiated Emissions, Fundamental and Harmonics Para. 15.231(b), Radiated Emissions, Spurious Case Para. 15.231(b), Duty Cycle Determination Para. 15.231(c), Occupied Bandwidth Retlif Testing Laboratories, Test Report R-10698-1, X-10(USA), FCC ID: B4SPH750T Page 2 of 18 REPORT OF MEASUREMENTS Applicant: X-10 (USA), Inc. Device: Pulsed Transmitter FCC ID: B4SPH750T Power Requirements: 3 VDC via two (2) “AAA” batteries Applicable Rule Section: Part 15, Subpart C, Section 15.231 TEST RESULTS 15.231 (a): This device is used as a remote control transmitter. 15.231 (a)(1) The transmitter is manually operated. Transmission ends within 5 seconds of deactivation. 15.231 (a)(3): The transmitter does not perform periodic transmissions. 15.231 (b): The fundamental field strength did not exceed 10333 μV/M (Average) at a test distance of 3 meters. In addition, the requirements of section 15.35 for averaging pulsed emissions and for limiting peak emissions were met. The field strength of harmonic and spurious emissions did not exceed 1033 μV/M (AVERAGE). DETERMINATION OF FIELD STRENGTH LIMITS The field strength limits shown below are found in Section 15.231. Frequency Limit F1 = 260 3750 = L1 Fo = 418 Lo F2 = 470 12500 = L2 The formula below was utilized to determine the limits: Limit = L1 + [(Fo-F1)(L2-L1)/(F2-F1)] Solving yields: Fundamental Limit = 10333 μV/M (AVERAGE) @ 3 Meters Harmonic Limit = 1033 μV/M (AVERAGE) @ 3 Meters Retlif Testing Laboratories, Test Report R-10698-1, X-10(USA), FCC ID: B4SPH750T Page 3 of 18 DUTY CYCLE DETERMINATION The unit’s RF output was directly coupled to the input of the spectrum analyzer. The analyzer was set for a frequency span of 0Hz. The sweep time was then adjusted in order to display one full pulse train. The transmitter on time was then summed and compared to the time for one full cycle in order to obtain the duty cycle. (See plots for additional information) Transmitter On Time = 21.925 milliseconds (maximum) Transmitter Cycle Time = 45 milliseconds Transmitter Duty Cycle = 48.7% CALCULATION: 1 Large Pulse = 2.5 milliseconds 9 x 1.425 ms(medium pulse) = 12.825 milliseconds 11 x 600 μs (small pulse) = 6.6 milliseconds 2.5 + 12.825 + 6.6 = 21.925 milliseconds Duty Cycle (21.925/45) = 48.7 % Correction Factor = 20 log (0.487) = -6.2 dB SPECTRUM ANALYZER DESENSITIZATION CONSIDERATIONS Due to the nature of the emissions being measured, care was taken to ensure that the resolution bandwidth of the spectrum analyzer was adequate to provide accurate measurements. The following formula was utilized: Setting pulse desensitization equal to zero and utilizing the minimum observed pulse width of 600 μs yields a minimum required bandwidth of 1111 Hz. FCC specified bandwidths of 100 kHz and 1 MHz were utilized below and above 1GHz, respectively. GENERAL NOTES 1. All readings were taken utilizing a peak detector function at a test distance of 3 meters. 2. The duty cycle was applied to the peak readings in order to determine the average value of the emissions. 3. The frequency range was scanned from 30 MHz to 4.2 GHz. All emissions not reported were more than 20 dB below the specified limit. Retlif Testing Laboratories, Test Report R-10698-1, X-10(USA), FCC ID: B4SPH750T Page 4 of 18 EQUIPMENT LIST Low Power Pulsed Transmitter Testing EN Type Manufacturer Description Model No. Cal Date Due 067 Open Area Test Site Retlif 3 Meter RNY 10/1/2003 10/1/2006 128 Double Ridged Guide Electro-Mechanics 1 GHz - 18 GHz 3105 6/21/2004 6/21/2005 133 Broadband Pre-Amplifier Electro-Metrics 10 kHz - 1 GHz, 26dB BPA-1000 6/12/2004 6/12/2005 141 Spectrum Analyzer Hewlett Packard 100 Hz - 40 GHz 8566B 8/5/2004 2/5/2005 141A Graphics Plotter Hewlett Packard N/A 7470A 2/9/2004 2/9/2005 141B Quasi-Peak Adaptor Hewlett Packard 100 Hz - 1 GHz 85650A 8/7/2004 2/7/2005 206B 6.0 dB Attenuator Texscan 0 - 1.0 GHz FP-50 - 6 dB 6/12/2004 6/12/2005 543 Preamplifier Hewlett Packard 1.0 GHz - 26.5 GHz 8449B 7/27/2004 7/27/2005 617 Interference Analyzer Electro-Metrics 10 kHz - 1 GHz EMC-30 10/5/2004 10/5/2005 767 Biconilog EMCO 26 - 2000 MHz 3142B 10/7/2004 10/7/2005 Retlif Testing Laboratories, Test Report R-10698-1, X-10(USA), FCC ID: B4SPH750T Page 5 of 18 FCC 15.231(b) RADIATED EMISSIONS, FUNDAMENTAL & SPURIOUS CASE Retlif Testing Laboratories, Test Report R-10698-1, X-10(USA), FCC ID: B4SPH750T Page 6 of 18 Test Method: FCC Part 15 Subpart C Radiated Emissions, Fundamental & Harmonic Emissions Customer: X-10 Wireless Technology, Inc. Job No. R-10698-1 Test Sample: Pulsed 418 MHz Transmitter Paragraph: 15.231 Model No.: PH750T FCC ID: B4SPH750T Operating Mode: Continuously Transmitting a pulsed 418 MHz signal Technician: R. Soodoo Date: December 16, 2004 Notes: Test Distance: 3 Meters Detector: Peak, Unless otherwise specified Test Freq. Antenna Pol./Height EUT Orientation Meter Reading Correction Factor Corrected Reading Converted Reading Peak Limit MHz (V/H)/Meters X / Y / Z dBuV dB dBuV/m uV/m uV/m 418 V/1.0 X 71.4-2.269.2 2884.0103333 | V/1.0 Y 72.8 -2.2 70.6 3388.4 | | V/1.0 Z 73.4 -2.2 71.2 3630.8 | | H/1.8 X 69.3 -1.7 67.6 2398.8 | | H/1.0 Y 67.1 -1.7 65.4 1862.1 | 418 H/1.5 Z 65.2 -1.7 63.5 1496.2 103333 836 V/1.0 X 35.0 6.8 41.8 123.0 10333 | V/1.0 Y 36.7 6.8 43.5 149.6 | | V/1.0 Z 40.1 6.8 46.9 221.3 | | H/1.0 X 36.6 6.9 43.5 149.6 | | H/1.5 Y 36.1 6.9 43.0 141.3 | 836 H/2.0 Z 34.8 6.9 41.7 121.6 1033…

Text truncated - open the document above for the full version.