B4SUR47A

Set Up and Operating Instructions for Remote Control Model UR47A To setup for A/V functions: Press and hold SETUP until the red lights stays on. Press and release TV, VCR, CBL, AUX, SAT or DVD. Enter the three digit code for your TV, VCR, etc., from the code list. Home Control operation: Plug in an X10 Transceiver (sold separately) and set it to Housecode A. You can control it and other X10 modules (set to Housecode A) as follows: Press and release any of the 4 ON-OFF rocker buttons at the bottom corresponding to the X10 Module you want to control. Set the slide switch on the side of the remote to control Modules set to Unit Codes 1-4 OR 5-8. To change the X10 Housecode: The UR47A Remote defaults to Housecode A, to change this: 1.Press and hold SETUP until the red light stays on. 2.Press and release the number button corresponding to the Housecode you want: (01=A, 02=B, 03=C .....16=P). Note: The Housecode you choose must match the Housecode on the Transceiver and X10 Modules you are using it with. F.C.C. CAUTION - THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. This equipment generates and uses radio frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturers instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for remote control security devices in accordance with the specifications in Sub-Part B of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by unplugging the equipment, try to correct the interference by one or more of the following measures. o Reorient the antenna of the radio/TV experiencing the interference. o Relocate the product with respect to the radio/TV. o Move the product away from the radio/TV. o Plug the product into an outlet on a different electrical circuit from the radio/TV experiencing the interference. If necessary, consult your local dealer for additional suggestions. NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TO THE UNITS. ANY CHANGES MADE TO THE UNITS WILL VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. X10 (USA) Inc., 91 Ruckman Rd., Closter, NJ 07624. www.x10.com UR47A-6/30/99

6 in 1 RF Universal Remote with DVD & Home Control Use with RR501 RF Transceiver and X10 Modules. Use 4 AAA alkaline batteries. X10 (USA) Inc., Closter, NJ 07624. 1. Press and hold SETUP until red light stays on. 2. Press and release mode button (TV, VCR, CBL, AUX, SAT, or DVD) 3. Enter 3 digit code from code book. 4. Press the ON-OFF buttons at bottom to control X10 Modules. FCC ID: B4SUR47A Made in China TVVCRCBLAUXSATDVD Model UR47A 6 in 1 Remote Control rating label 2: 1 6/30/99 Model UR47A

Operational Description The UR47A is a 310 MHz transmitter used for remote control purposes. It is manually operated and ceases operation within 5 seconds after activation. It does not perform periodic transmissions.

0UR47A-3DVD REMOTE CONTROL 1UR47A-3UDVD REMOTE CONTROL NOPACK1 0.2038020H11492RATING LABEL (X-10)1 0.2183010H14940BATTERY DOOR1 0.2183010H17530KNOB COVER1 0.2185000H16760TOP CABINET1 0.2185000H16770BOTTOM CABINET1 0.2275000H10770KEYPAD1 0.2403011H10136SPRING CONTACT (+VE)1 0.2403011H10137SPRING CONTACT (-VE)2 0.2851001H10598RS REMOTE, RF 310MHZ1 ..3042010H10410PCB, RF1 ..3076-10000002CAP-MCC 10P 5% NPO 08051 ..3076-10900000CAP-MCC 1P .25P NPO 08052 ..3076-30900000CAP-MCC 3P .25P NPO 08051 ..3076-70900000CAP-MCC 7P .25P NPO 08051 ..3124000H10001RF COIL 31T1 ..3162089H10014RF WIRE LOOP ID=6 WD=0.61 ..3209117H10002TRS-NPN MPS H101 ..3212107H10000DIODE-SI 1N41481 ..3240-68206011RES-CF 6K8 +/-5% 1/8W1 ..3241-68000000RES-TFC 68R 5% 1/10W 08051 ..3241-68200000RES-TFC 6K8 5% 1/10W 08051 ..3358-60821001WIRE-JUMPER D=0.6MM4 0.2851001H10998PCB ASSY1 ..3042010H10668APCB1 ..3055-10400000CAP-C 100N +8-2 25V Y5V2 ..3057-10100019CAP-E 100U 20% 10V1 ..3080001H100504MHZ RESONATOR W/2 CAP1 ..3210010H10010TRS-H90131 ..3211328H10174IC GMS81032 (X1005)1 ..3212107H10000DIODE-SI 1N41483 ..3220-00200180LED 3MM (RED DIFFUSED)1 ..3220-00200220IR EMITTING LED 5MM1 ..3240-10506011RES-CF 1M +/-5% 1/8W1 ..3240-33106022RES-CF 330R +/-5% 1/4W1 ..3240-33906022RES-CF 3R3 +/-5% 1/4W1 ..3240-68106022RES-CF 680R +/-5% 1/4W1 ..3283-00000012SLIDE SWITCH (1P2T)1 ..3358-60821001WIRE-JUMPER D=0.6MM1 ..3403011H10113SPRING CONTACT (+VE)1 ..3403011H10114SPRING CONTACT (-VE)1

D C B A 12345678 A B C D 87654321 PICO ELECTRONICS Ltd., Eastfield Industrial Estate, Glenrothes, Fife, KY7 4NZ, SCOTLAND SHEET No. DATE DATE REVISION DATE FIRST DRAWN FILE DRN APPD. DO NOT SCALE DRAWING TITLE: REV. Error : PICO.WMF File Not Found F:\JOSEPH\UR47AB.SCH 11of B UR47A USA X10/DVD REMOTE PRINT DATE 16:03:4729-Jun-1999 KEY15 RETURN 2/8 (B) KEY16 ENTER 2/9 KEY17 DISPLAY 2/10 (A) KEY18 OKAY 2/11 KEY19 A/B 2/18 KEY20 UP 2/19 KEY22 9 1/8 KEY23 4 1/9 KEY24 7 1/10 KEY25 EXIT 1/11 KEY26 6 1/18 KEY27 8 1/19 KEY29 VCR 28/8 (AUX-A) KEY30 TV 28/9 KEY31 POWER 28/10 KEY32 ALL LTS ON 28/11 (FIX-X10) KEY33 DVD 28/18 (AUX-D) KEY34 SAT 28/19 (AUX-C) KEY36 VOL.UP 27/8 KEY37 AUX (MOUSE) 27/9 (AUX-E) KEY38 VOL.DOWN 27/10 KEY41 MUTE 27/19 KEY43 3 26/8 KEY45 1 26/10 KEY47 RECALL 26/18 KEY48 2 26/19 KEY8 SUBTITLE 3/8 (CC) KEY9 TITLE 3/9 (C) KEY10 MENU 3/10 KEY11 SKIP DOWN 3/11 KEY12 RIGHT 3/18 KEY1 PAUSE 4/8 KEY2 RECORD 4/9 KEY3 REWIND 4/10 KEY4 SKIP UP 4/11 KEY5 FF 4/18 KEY6 STOP 4/19 Y1 4MHZ LED1 R2 330R IR1 TR1 9013G VSS VSS 4 x AAA BATTERIES BATT1 BATT2 +6V C4 VSS OPTIONAL R3 3R3 R1 1M NOTES:- 1/ ALL UNSPECIFIED DIODES 1N4148 OR EQUIVALENT. 2/ ALL UNSPECIFIED DAUGHTER BOARD CAPACITORS ARE SMD TYPE. 3/ ALL UNSPECIFIED DAUGHTER BOARD RESISTORS ARE SMD TYPE. 4/ ALL UNSPECIFIED RESISTORS ARE 0.125W 5%. 5/ ALL UNSPECIFIED CAPACITORS ARE AXIAL MLC TYPE. "*" DENOTES COMPONENT NOT INSTALLED +V R4 680R * R11 3 R12 2 VDD 5 Xout 6 Xin 7 R00 8 R01 9 R02 10 R03 11 R20 12 VSS 17 R04 18 R05 19 R06 20 R07 21 TEST 22 RESET 23 REMOUT 24 R17 25 R10 4 R13 1 R14 28 R15 27 R16 26 R21 13 R22 14 R23 15 R24 16 1 GMS81032-28 C3 100NF VSS C2 100UF 6.3V SIGNAL ENABLE BKW31/5/99 31/5/99 2/6/99 KEY50 1-ON 25/8 (FIX-X10) KEY52 2-ON 25/10 (FIX-X10) KEY54 3-OFF 25/18 (FIX-X10) KEY55 4-ON 25/19 (FIX-X10) KEY13 DOWN 3/19 KEY39 ALL OFF 27/11 (FIX-X10) KEY46 3-ON 26/11 (FIX-X10) KEY53 2-OFF 25/11 (FIX-X10) KEY44 SETUP 26/9 KEY51 1-OFF 25/9 (FIX-X10) KEY21 0 2/20 KEY28 5 1/20 KEY35 CABLE 28/20 (AUX-B) KEY42 CH.UP 27/20 KEY49 CH.DOWN 26/20 KEY7 PLAY 4/20 KEY56 4-OFF 25/20 (FIX-X10) KEY14 LEFT 3/20 DAUGHTER BOARD OPTIONAL RF DAUGHTER BOARD VSS V+ R11 6K8 C4 10PF C5 1P C6 * C7 7P C8 2P R12 6K8 TR4 MPSH10 R13 68R D2 L1 6MM L2 31T D=2MM SHOWN FOR REFERENCE ONLY D3D4D5 SW1 SK-12D20 BATT3 BATT4 VSS 0=DEVICE GROUP 1-4 1=DEVICE GROUP 5-8 C5 100NF

Test Report No. R-8155-1 FCC ID: B4SUR47A APPLICANT X-10 (USA), Inc. 91 Ruckman Road Closter, NJ 07624-0420 MANUFACTURER X-10 Electronics Shenzhen Co. Ltd. X-10 Building Labour Industrial District Shenzhen, Xixiang, Bao An Guang Dong, China, 518102 TEST SPECIFICATION: FCC Rules and Regulations Part 15, Subpart C, Para. 15.231 TEST PROCEDURE: ANSI C63.4:1992 TEST SAMPLE DESCRIPTION BRANDNAME: X-10 (USA), Inc. MODEL: UR47A TYPE: 310 MHz RF Transmitter POWER REQUIREMENTS: 6 VDC Via (4) “AAA” Batteries FREQUENCY OF OPERATION: 310 MHz TESTS PERFORMED Para. 15.231(a), Radiated Emissions, Fundamental and Harmonics Para. 15.231(c), Occupied Bandwidth Duty Cycle Determination REPORT OF MEASUREMENTS Applicant: X-10 (USA), Inc. Device:310 MHz RF Remote Control FCC ID: B4SUR47A Power Requirements: 6 VDC Via (4) “AAA” Batteries Applicable Rule Section:Part 15, Subpart C, Section 15.231 Test Report No. R-8155-1 FCC ID: B4SUR47A REPORT OF MEASUREMENTS (continued) TEST RESULTS 15.231 (a) -The device is used as a transmitter for security purposes. 15.231 (a)(1) & -The transmitter is manually operated and ceases transmission within 5 15.231(2)seconds after deactivation. 15.231 (a)(3) -The transmitter does not perform periodic transmissions. 15.231 (a)(4)-The device is employed for RC purposes involving security. 15.231 (b) -The fundamental field strength did not exceed 5833 μV/M (Average) at a test distance of 3 meters. In addition, the requirements of section 15.35 for averaging pulsed emissions and for limiting peak emissions were met. The field strength of harmonic and spurious emissions did not exceed 583 μV/M (AVERAGE). 15.231 (c) -The device operates at 310 MHz. The bandwidth of emissions did not exceed 0.25% of the operating frequency (775 kHz). DETERMINATION OF FIELD STRENGTH LIMITS The field strength limits shown below are found in Section 15.231. Frequency Limit F1=2603750 =L1 Fo=310Lo F2=47012500 =L2 The formula below was utilized to determine the limits: Limit = L1 + [(Fo-F1)(L2-L1)/(F2-F1)] Solving yields: Fundamental Limit= 5,833 μV/M (AVERAGE) @ 3 Meters Harmonic Limit= 583 μV/M (AVERAGE) @ 3 Meters Test Report No. R-8155-1 FCC ID: B4SUR47A REPORT OF MEASUREMENTS (continued) DETERMINATION OF DUTY CYCLE The unit’s RF output was directly coupled to the input of the spectrum analyzer. The analyzer was set for a frequency span of 0Hz. The sweep time was then adjusted in order to display one full pulse train. The transmitter on time was then summed and compared to the time for one full cycle in order to obtain the duty cycle. (See separate e-file attachments named Dutycycle1.pdf, Dutycycle2.pdf, Dutycycle3.pdf for plots) Transmitter On Time=31.2 milliseconds (maximum- worst case in 100 ms) Transmitter Cycle Time=107.0 milliseconds Transmitter Duty Cycle=31.2 % CALCULATION: 1 Large Pulse = 9.17 milliseconds 33 x 667 μs (small pulse)= 22.01 milliseconds 9.17 + 22.01= 31.2 milliseconds Duty Cycle=31.2 % Correction Factor = 20 log(0.285) = -10.1 SPECTRUM ANALYZER DESENSITIZATION CONSIDERATIONS Due to the nature of the emissions being measured, care was taken to ensure that the resolution bandwidth of the spectrum analyzer was adequate to provide accurate measurements. The following formula was utilized: Setting pulse desensitization equal to zero and utilizing the minimum observed pulse width of 667μs yields a minimum required bandwidth of 999.5 Hz. FCC specified bandwidths of 100kHz and 1MHz were utilized below and above 1GHz, respectively. Test Report No. R-8155-1 FCC ID: B4SUR47A REPORT OF MEASUREMENTS (continued) GENERAL NOTES 1. All readings were taken utilizing a peak detector function at a test distance of 3 meters. 2. The duty cycle was applied to the peak readings in order to determine the average value of the emissions. 3. All measurements were made with (4) new “AAA” Batteries. 4. The frequency range was scanned from 30 MHz to 3.1 GHz . All emissions not reported were more than 20 dB below the specified limit. Test Report No. R-8155-1 FCC ID: B4SUR47A EQUIPMENT LIST FCC Part 15 Subpart C Radiated Emissions Paragraph 15.231(b) ENTypeManufacturerFrequency Range Model No.Cal Date Due Date 067Open Area Test SiteRetlif3 MeterRNY8/30/978/30/99 128CDouble Ridge GuideEaton Corporation1 GHz - 18 GHz9600110/6/9810/6/99 133Broadband Pre-AmplifierElectro-Metrics10 kHz - 1 GHz, 26dBBPA-10006/22/986/22/99 141Spectrum AnalyzerHewlett Packard100 Hz - 40 GHz8566B3/16/999/16/99 141AGraphics PlotterHewlett PackardN/A7470A3/5/993/5/00 141BQuasi-Peak AdaptorHewlett Packard100 Hz - 1 GHz85650A3/16/999/16/99 206B6.0 dB AttenuatorTexscan0 - 1.0 GHzFP-50 - 6 dB6/22/986/22/99 523BiconilogElectro-Mechanics26 - 2000 MHz3142B10/22/984/22/00 543PreamplifierHewlett Packard1.0 GHz - 26.5 GHz8449B9/3/989/3/99 Test Report No. R-8155-1 FCC ID: B4SUR47A FCC 15.231(b) RADIATED EMISSIONS, FUNDAMENTAL & SPURIOUS CASE (See separate e-file attachment named 310Mhz231.Doc) Test Report No. R-8155-1 FCC ID: B4SUR47A FCC 15.231(c) OCCUPIED BANDWIDTH (See separate e-file attachment named OccBw1.pdf and OccBw2.pdf) Test Report No. R-8155-1 FCC ID: B4SUR47A DUTY CYCLE PLOTS (See separate e-file attachment named Dutycycle1.pdf, Dutycycle2.pdf, and Dutycycle3.pdf)

Data Sheet 1 of 2 Test Method: FCC Part 15 Subpart C Radiated Emissions Paragraph 15.231 Customer: X-10 (USA) Inc Job No. R-8155-1 Test Sample: Pulsed RF Transmitter FCC ID: B4SUR47A Model No.: UR47A Serial No. N/A Operating Mode: Continuously Transmitter 310 Mhz Signal Technician: Dennis Cortes Date: June 31,1999 Notes: Test Distance: 3 Meters Temp: 31C Humidity:90% Detector: Peak Test Freq. Antenna Pol./Height EUT Orientation Meter Reading Correction Factor Corrected Reading Converted Reading Peak Limit Mhz(V/H) / DegreesX / Y / Z dBuv dB dBuV/m uV/m uV/m 310.0H / 1.0X69.7-4.065.71927.558330 310.0H / 1.2Y82.0-4.078.07943.358330 310.0H / 1.0Z79.8-4.075.86166.058330 310.0V / 1.5X80.0-4.076.06309.658330 310.0V / 1.3Y72.0-4.068.02511.958330 310.0V / 1.0Z68.0-4.064.01584.958330 620.0H / 1.6X47.23.250.4331.15833 620.0H / 1.1Y57.23.260.41047.15833 620.0H / 1.4Z57.03.260.21023.35833 620.0V / 1.0X60.33.263.51496.25833 620.0V / 1.0Y51.63.254.8549.55833 620.0V / 1.3Z51.43.254.6537.05833 930.0H / 1.2X32.87.440.2102.35833 930.0H / 1.0Y35.67.443.0141.35833 930.0H / 1.1Z33.07.440.4104.75833 930.0V / 1.3X34.37.441.7121.65833 930.0V / 1.2Y32.37.439.796.65833 930.0V / 1.0Z31.97.439.392.35833 1240.0H & VX, Y, Z43.7-3.839.9*98.95000 1550.0H & VX,Y, Z44.3-0.144.2*162.25000 1860.0H & VX,Y, Z44.11.645.7*192.85833 2170.0H & VX,Y, Z43.4-1.342.1*127.45833 2480.0H & VX,Y, Z43.30.143.4*147.95833 2790.0H & VX,Y, Z42.51.443.9*156.75000 3100.0H & VX,Y, Z42.33.545.8*195.05833 The frequency range was scanned from 30 Mhz to 3.1 Ghz. All emissions not recorded were more Than 10 dB below the specified limit. Emissions from the EUT do not exceed the specified limits. *=Noise Floor Measurements ( Minimum system sensitivity) Data Sheet 2 of 2 Test Method: FCC Part 15 Subpart C Radiated Emissions Paragraph 15.231 Customer: X-10 (USA) Inc Job No. R-8155-1 Test Sample: Pulsed RF Transmitter FCC ID: B4SUR47A Model No.: UR47A Serial No. N/A Operating Mode: Continuously Transmitter 310 Mhz Signal Technician: Dennis Cortes Date: June 31,1999 Notes: Test Distance: 3 Meters Duty Cycle: 31.2% Detector: Peak Duty Cycle Correction: -10.1 dB Test Freq. Antenna Pol./Height EUT Orientation Peak Reading Correction Factor Corrected Reading Converted Reading Peak Limit Mhz(V/H) / DegreesX / Y / Z dBuv dB dBuV/m uV/m uV/m 310.0H / 1.0X65.7-10.155.6602.65833 310.0H / 1.2Y78.0-10.167.92483.15833 310.0H / 1.0Z75.8-10.165.71927.55833 310.0V / 1.5X76.0-10.165.91972.45833 310.0V / 1.3Y68.0-10.157.9785.25833 310.0V / 1.0Z64.0-10.153.9495.55833 620.0H / 1.6X50.4-10.140.3103.5583 620.0H / 1.1Y60.4-10.150.3327.3583 620.0H / 1.4Z60.2-10.150.1319.9583 620.0V / 1.0X63.5-10.153.4467.7583 620.0V / 1.0Y54.8-10.144.7171.8583 620.0V / 1.3Z54.6-10.144.5167.9583 930.0H / 1.2X40.2-10.130.132.0583 930.0H / 1.0Y43.0-10.132.944.2583 930.0H / 1.1Z40.4-10.130.332.7583 930.0V / 1.3X41.7-10.131.638.0583 930.0V / 1.2Y39.7-10.129.630.2583 930.0V / 1.0Z39.3-10.129.228.8583 1240.0H & VX, Y, Z39.9-10.129.8*30.9500 1550.0H & VX,Y, Z44.2-10.134.1*50.7500 1860.0H & VX,Y, Z45.7-10.135.6*60.3583 2170.0H & VX,Y, Z42.1-10.132.0*39.8583 2480.0H & VX,Y, Z43.4-10.133.3*46.2583 2790.0H & VX,Y, Z43.9-10.133.8*49.0500 3100.0H & VX,Y, Z45.8-10.135.7*61.0583 The frequency range was scanned from 30 Mhz to 3.1 Ghz. All emissions not recorded were more Than 10 dB below the specified limit. Emissions from the EUT do not exceed the specified limits. *=Noise Floor Measurements ( Minimum system sensitivity) Data Sheet 3 of 2