B4SUR85ACamShow Remote

CamShow Remote For use with VK73A VGA Picture Sender Model UR85A UR85A-8/01 The CamShow Remote works with the VK73A CamShow system for situations where you want to have an additional remote, or if you are replacing a lost or broken remote. The remote lets you access all the features of the CamShow application from the comfort of your easy chair. It can also adjust the color, brightness, contrast, etc., of the picture sent from the Picture Sender to the Receiver that you connect to your TV. See VK73A owner’s manual for more information. 1.Push the tab and lift off the battery cover. 2.Insert four AAA alkaline batteries, taking care to match the + and - marks in the battery compartment. BUTTON DESCRIPTIONS Indicator light The indicator light flashes when you press any button. Start Launches the CamShow application. A, B, C, D Selects the four main functions of the CamShow application. Up, Down, Left, Right Arrows Moves picture on screen. OK Selects a selection. Zoom In/Zoom Out Zooms in and out on the picture being displayed. 0-9 Enters picture numbers directly. Forward/Backward Selects direction to move through your picture album. Page Up/Page Down Goes to the next or previous page in your photo album. Subtitles Turns subtitles on and off. Page u p Fo rward Ba ck wa rdPage d o wn Subtitle 2 13 456 78 0 9 OK A BC D Start 1.Press A to List photo albums. 2.Press B to View thumbnail views of the pictures in the album you selected when you pressed A. 3.Press C to Search through collections of photos you have grouped together. 4.Press D to access Help. 5.Press A to select an album, then press B to view thumbnail views of the pictures in the album, then press a number button corresponding to the thumbnail number of the photo you want to view. 6.Moves forward and backwards through the selected album. 7.Moves through your albums. 8.Zooms in and out on the picture being displayed. ™ F.C.C. CAUTION - THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TO THE UNITS. ANY CHANGES MADE TO THE UNITS WILL VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. LIMITED 1-YEAR WARRANTY Please visit www.x10.com/warranty to complete your on-line warranty registration. Thank you. For help or more information on setup, please visit: www.x10.com/support

MCU (EM78P156E) Block Diagram for UR85A RF REMOTE Key Matrix 310MHzTransmitter 310MHz

CamShow Remote Use with VT37A CamShow VGA Video Sender Use 4 AAA alkaline batteries. Model UR85A (VGA) Remote Control rating label 2: 1 8/22/01 FCC ID: B4SUR85A Made in China X10.com, a div. of X10 Wireless Technology, Inc. www.x10.com/support Model UR85A

CamShow Remote For use with VK73A VGA Picture Sender Model UR85A UR85A-8/01 The CamShow Remote works with the VK73A CamShow system for situations where you want to have an additional remote, or if you are replacing a lost or broken remote. The remote lets you access all the features of the CamShow application from the comfort of your easy chair. It can also adjust the color, brightness, contrast, etc., of the picture sent from the Picture Sender to the Receiver that you connect to your TV. See VK73A owner’s manual for more information. 1.Push the tab and lift off the battery cover. 2.Insert four AAA alkaline batteries, taking care to match the + and - marks in the battery compartment. BUTTON DESCRIPTIONS Indicator light The indicator light flashes when you press any button. Start Launches the CamShow application. A, B, C, D Selects the four main functions of the CamShow application. Up, Down, Left, Right Arrows Moves picture on screen. OK Selects a selection. Zoom In/Zoom Out Zooms in and out on the picture being displayed. 0-9 Enters picture numbers directly. Forward/Backward Selects direction to move through your picture album. Page Up/Page Down Goes to the next or previous page in your photo album. Subtitles Turns subtitles on and off. Page u p Fo rward Ba ck wa rdPage d o wn Subtitle 2 13 456 78 0 9 OK A BC D Start 1.Press A to List photo albums. 2.Press B to View thumbnail views of the pictures in the album you selected when you pressed A. 3.Press C to Search through collections of photos you have grouped together. 4.Press D to access Help. 5.Press A to select an album, then press B to view thumbnail views of the pictures in the album, then press a number button corresponding to the thumbnail number of the photo you want to view. 6.Moves forward and backwards through the selected album. 7.Moves through your albums. 8.Zooms in and out on the picture being displayed. ™ F.C.C. CAUTION - THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TO THE UNITS. ANY CHANGES MADE TO THE UNITS WILL VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. LIMITED 1-YEAR WARRANTY Please visit www.x10.com/warranty to complete your on-line warranty registration. Thank you. For help or more information on setup, please visit: www.x10.com/support

D C B A 12345678 A B C D 87654321 PICO ELECTRONICS Ltd., Eastfield Industrial Estate, Glenrothes, Fife, KY7 4NZ, SCOTLAND SHEET No. DATE DATE REVISION DATE FIRST DRAWN FILE DRN APPD. DO NOT SCALE DRAWING TITLE: REV. Error : PICO.WMF File Not Found C:\WINDOWS\DESKTOP\UR85AB.SCH 11of B X10 VGA RF REMOTE UR85A PRINT DATE 20:45:4121-Aug-2001 VDD KEY11 9 10/17 KEY12 D 10/18 KEY13 8 1/10 KEY14 A 2/10 KEY15 7 10/VSS KEY18 5 1/11 KEY20 4 11/VSS 4 x AAA BATTERIES BATT1 BATT2 Y1 4MHZ R1 * BKW14/8/01 14/8/01 15/8/01 KEY16 6 11/17 VSS C3 100NF C2 100UF 10V C4 * VSSVSS NOTES:- 1/ ALL UNSPECIFIED DIODES 1N4148 OR EQUIVALENT. 3/ ALL UNSPECIFIED RESISTORS ARE 0.125W 5%. 4/ ALL UNSPECIFIED CAPACITORS ARE AXIAL MLC TYPE. "*" DENOTES COMPONENT NOT INSTALLED LED1 3MM RED R2 120R VDD 14 VSS 5 P60 6 OSCO 15 OSCI 16 P53 2 P52 1 P51 18 P50 17 P64 10 P63 9 P62 8 P67 13 P66 12 P61 7 P65 11 TCC 3 RESET 4 U1 BATT3 BATT4 EM78P156E D3D2D1 VSS SIGNAL ENABLE RF DAUGHTER BOARD SHOWN FOR REFERENCE ONLY VSS R11 6K8 C4 10PF C5 1P C6 * C7 7P C8 2P R12 6K8 TR4 MPSH10 R13 68R D2 L1 6MM L2 31T D=2MM DAUGHTER BOARD +6V * KEY17 C 11/18 KEY19 B 2/11 KEY6 PAGE UP 9/17 KEY7 START 9/18 KEY8 0 1/9 KEY9 LEFT 2/9 KEY10 FORWARD 9/VSS KEY26 ZOOM OUT 13/17 KEY21 3 12/17 KEY22 UP 12/18 KEY27 RIGHT 13/18 KEY23 2 1/12 KEY25 1 12/VSS KEY28 DOWN 1/13 KEY30 ZOOM IN 13/VSS KEY1 PAGE DN 8/17 KEY3 SUBTITLE 1/8 KEY4 OK 2/8 KEY5 BACKWARD 8/VSS

Test Report No. R-9150-1 FCC ID: B4SUR85A APPLICANT X-10 (USA), Inc. 400 Forge Way, Suite 412 Rockaway, NJ 07866-2033 MANUFACTURER X-10 Electronics Shenzhen Co. Ltd. X-10 Building Labour Industrial District Shenzhen, Xixiang, Bao An Guang Dong, China, 518102 TEST SPECIFICATION:FCC Rules and Regulations Part 15, Subpart C, Para. 15.231 TEST PROCEDURE:ANSI C63.4:1992 TEST SAMP LE DESCRIP TION BRANDNAME: X-10 (USA), Inc. MODEL: UR85A TYPE: Pulsed Transmitter POWER REQUIREMENTS: 6 VDC derived from (4) new “AAA” 1.5 VDC Batteries FREQUENCY OF OPERATION: 310 MHz TESTS P ERFORMED Para. 15.231(b)(1), Radiated Emissions, Fundamental and Harmonics Para. 15.231(c), Radiated Emissions, Spurious Case Para. 15.35, Duty Cycle Determination Para. 15.231(c), Occupied Bandwidth REPORT OF MEASUREMENTS Applicant: X-10 (USA), Inc. Device:Pulsed Transmitter FCC ID: B4SUR85A Power Requirements: 6 VDC derived from (4) new “AAA” 1.5 VDC Batteries Applicable Rule Section:Part 15, Subpart C, Section 15.231 Test Report No. R-9150-1 FCC ID: B4SUR85A REPORT OF MEASUREMENTS (continued) TEST RESULTS 15.231 (a):This device is used as a remote control transmitter. 15.231 (a)(1) &The transmitter is manually operated and ceases transmission within 5 15.231(a)(2):seconds after deactivation. 15.231 (a)(3):The transmitter does not perform periodic transmissions. 15.231 (b):The fundamental field strength did not exceed 5833 μV/M (Average) at a test distance of 3 meters. In addition, the requirements of section 15.35 for averaging pulsed emissions and for limiting peak emissions were met. The field strength of harmonic and spurious emissions did not exceed 583 μV/M (AVERAGE). DETERMINATION OF FIELD STRENGTH LIMITS The field strength limits shown below are found in Section 15.231. Frequency Limit F1=2603750 =L1 Fo=312Lo F2=47012500 =L2 The formula below was utilized to determine the limits: Limit = L1 + [(Fo-F1)(L2-L1)/(F2-F1)] Solving yields: Fundamental Limit= 5833 μV/M (AVERAGE) @ 3 Meters Harmonic Limit= 583 μV/M (AVERAGE) @ 3 Meters Test Report No. R-9150-1 FCC ID: B4SUR85A REPORT OF MEASUREMENTS (continued) DUTY CYCLE DETERMINATION The unit’s RF output was directly coupled to the input of the spectrum analyzer. The analyzer was set for a frequency span of 0Hz. The sweep time was then adjusted in order to display one full pulse train. The transmitter on time was then summed and compared to the time for one full cycle in order to obtain the duty cycle. (See plots for additional information) Transmitter On Time=16.6 milliseconds (maximum- per cycle) Transmitter Cycle Time=47.7 milliseconds Transmitter Duty Cycle=34.8 % CALCULATION: 1 Large Pulse = 4.0 milliseconds 21 x 600 μs (small pulse)= 12.6 milliseconds 4.0 + 12.6= 16.6 milliseconds Cycle Time=47.7 milliseconds Duty Cycle =16.6 / 47.7 = 34.8 % Correction Factor = 20 log(0.348) =-9.2 SPECTRUM ANALYZER DESENSITIZATION CONSIDERATIONS Due to the nature of the emissions being measured, care was taken to ensure that the resolution bandwidth of the spectrum analyzer was adequate to provide accurate measurements. The following formula was utilized: Setting pulse desensitization equal to zero and utilizing the minimum observed pulse width of 600μs yields a minimum required bandwidth of 1.11 kHz. FCC specified bandwidths of 100kHz and 1MHz were utilized below and above 1GHz, respectively. Test Report No. R-9150-1 FCC ID: B4SUR85A GENERAL NOTES 1. All readings were taken utilizing a peak detector function at a test distance of 3 meters. 2. The duty cycle was applied to the peak readings in order to determine the average value of the emissions. 3. The frequency range was scanned from 30 MHz to 3.1 GHz. All emissions not reported were more than 20 dB below the specified limit. Test Report No. R-9150-1 FCC ID: B4SUR85A EQUIPMENT LIST FCC15.231 Compliance Testing ENTypeManufacture rDe scriptionMode l No.Cal Date Due Date 067Open Area Test SiteRetlif3 MeterRNY9/20/009/20/03 128CDouble Ridge GuideEaton Corporation1 GHz - 18 GHz960019/18/009/18/01 133Broadband Pre-AmplifierElectro-Metrics10 kHz - 1 GHz, 26dBBPA-10006/13/016/13/02 141Spectrum AnalyzerHewlett Packard100 Hz - 40 GHz8566B7/2/011/2/02 141AGraphics PlotterHewlett PackardN/A7470A3/5/013/5/02 141BQuasi-Peak AdaptorHewlett Packard100 Hz - 1 GHz85650A2/20/011/2/02 206B6.0 dB AttenuatorTexscan0 - 1.0 GHzFP-50 - 6 dB6/13/016/13/02 523BiconilogElectro-Mechanics26 - 2000 MHz3142B6/8/009/8/01 543PreamplifierHewlett Packard1.0 GHz - 26.5 GHz8449B6/27/016/27/02 617Interference AnalyzerElectro-Metrics10 kHz - 1 GHzEMC-302/27/012/27/02 Test Report No. R-9150-1 FCC ID: B4SUR85A FCC 15.231(b) and FCC 15.231(c) RADIATED EMISSIONS, FUNDAMENTAL & SPURIOUS CASE See separate e-file attachment named REfundharm.pdf and REspur.pdf FCC 15.231(c) OCCUPIED BANDWIDTH Please refer to separate electronic file named Occbw.pdf Test Report No. R-9150-1 FCC ID: B4SUR85A FCC 15.35 DUTY CYCLE Please refer to separate electronic file named Dutycycle.pdf Test Report No. R-9150-1 FCC ID: B4SUR85A Test Setup Photograph

Retlif Testing Laboratories R Data Sheet 1 of 4 Test Method: FCC Part 15 Subpart C Radiated Emissions, Fundamental & Harmonic Emissions Customer: X-10 (USA) Job No. R-9150-1 Test Sample: RF remote Paragraph: 15.231 Model No.: UR85A FCC ID: B4SUR85A Operating Mode: Continuously Transmitting a 310 MHz Signal Technician: Peter Lananna Date: August 23, 2001 Notes: Test Distance: 3 Meters Detector: Peak, Unless otherwise specified Test Freq. Antenna Pol./Height EUT Orientation Meter Reading Correction Factor Corrected Reading Converted Reading Peak Limit MHz (V/H)/Meters X / Y / Z dBuV dB dBuV/m uV/m uV/m 310 H / 1.0 X 62.7 -4.0 58.7 861.0 58300 | H / 1.0 Y 64.2 -4.0 60.2 1023.3 | | H / 2.3 Z 60.2 -4.0 56.2 645.7 | | V / 1.3 X 62.0 -4.0 58.0 794.3 | | V / 3.0 Y 55.0 -4.0 51.0 354.8 | 310 V / 1.8 Z 61.0 -4.0 57.0 707.9 58300 620 H / X 36.5 3.9 40.4 104.7* 5830 | H / Y 36.5 3.9 40.4 104.7* | | H / Z 36.5 3.9 40.4 104.7* | | V / X 36.5 3.9 40.4 104.7* | | V / Y 36.5 3.9 40.4 104.7* | 620 V / Z 36.5 3.9 40.4 104.7* 5830 930 H / X 29.9 8.8 38.7 86.1* 5830 | H / Y 29.9 8.8 38.7 86.1* | | H / Z 29.9 8.8 38.7 86.1* | | V / X 29.9 8.8 38.7 86.1* | | V / Y 29.9 8.8 38.7 86.1* | 930 V / Z 29.9 8.8 38.7 86.1* 5830 1240 H / X 41.7 -2.8 38.9 88.1* 5000 | H / Y 41.7 -2.8 38.9 88.1* | | H / Z 41.7 -2.8 38.9 88.1* | | V / X 41.7 -2.8 38.9 88.1* | | V / Y 41.7 -2.8 38.9 88.1* | 1240 V / Z 41.7 -2.8 38.9 88.1* 5000 1550 H / X 39.7 0.9 40.6 107.2* 5000 | H / Y 39.7 0.9 40.6 107.2* | | H / Z 39.7 0.9 40.6 107.2* | | V / X 39.7 0.9 40.6 107.2* | | V / Y 39.7 0.9 40.6 107.2* | 1550 V / Z 39.7 0.9 40.6 107.2* 5000 The frequency range was scanned from 30 MHz to 3.1 GHz. All emissions not recorded were more Than 10 dB below the specified limit. Emissions from the EUT do not exceed the specified limits. *=Noise Floor Measurements (Minimum system sensitivity) Retlif Job Number R-9150-1 Retlif Testing Laboratories R Data Sheet 2 of 4 Test Method: FCC Part 15 Subpart C Radiated Emissions, Fundamental & Harmonic Emissions Customer: X-10 (USA) Job No. R-9150-1 Test Sample: RF remote Paragraph: 15.231 Model No.: UR85A FCC ID: B4SUR85A Operating Mode: Continuously Transmitting a 310 MHz Signal Technician: Peter Lananna Date: August 23, 2001 Notes: Test Distance: 3 Meters Detector: Peak, unless otherwise specified Test Freq. Antenna Pol./Height EUT Orientation Meter Reading Correction Factor Corrected Reading Converted Reading Peak Limit MHz (V/H)-Meters X / Y / Z dBuV dB dBuV/m uV/m uV/m 1860 H / 1.0 X 38.7 3.0 41.7 121.6* 5830 | H / 1.0 Y 38.7 3.0 41.7 121.6* | | H / 1.0 Z 38.7 3.0 41.7 121.6* | | V /1.0 X 38.7 3.0 41.7 121.6* | | V / 1.0 Y 38.7 3.0 41.7 121.6* | 1860 V / 1.0 Z 38.7 3.0 41.7 121.6* 5830 2170 H / 1.0 X 39.2 0.4 39.6 95.5* 5830 | H / 1.0 Y 39.2 0.4 39.6 95.5* | | H / 1.0 Z 39.2 0.4 39.6 95.5* | | V /1.0 X 39.2 0.4 39.6 95.5* | | V / 1.0 Y 39.2 0.4 39.6 95.5* | 2170 V / 1.0 Z 39.2 0.4 39.6 95.5* 5830 2480 H / 1.0 X 39.7 3.8 43.5 149.6* 5830 | H / 1.0 Y 39.7 3.8 43.5 149.6* | | H / 1.0 Z 39.7 3.8 43.5 149.6* | | V /1.0 X 39.7 3.8 43.5 149.6* | | V / 1.0 Y 39.7 3.8 43.5 149.6* | 2480 V / 1.0 Z 39.7 3.8 43.5 149.6* 5830 2790 H / 1.0 X 38.2 5.8 44.0 158.5* 5000 | H / 1.0 Y 38.2 5.8 44.0 158.5* | | H / 1.0 Z 38.2 5.8 44.0 158.5* | | V /1.0 X 38.2 5.8 44.0 158.5* | | V / 1.0 Y 38.2 5.8 44.0 158.5* | 2790 V / 1.0 Z 38.2 5.8 44.0 158.5* 5000 3100 H / 1.0 X 40.0 6.4 46.4 208.9* 5830 | H / 1.0 Y 40.0 6.4 46.4 208.9* | | H / 1.0 Z 40.0 6.4 46.4 208.9* | | V /1.0 X 40.0 6.4 46.4 208.9* | | V / 1.0 Y 40.0 6.4 46.4 208.9* | 3100 V / 1.0 Z 40.0 6.4 46.4 208.9* 5830 The frequency range was scanned from 30 MHz to 3.1 GHz. All emissions not recorded were more Than 10 dB below the specified limit. Emissions from the EUT do not exceed the specified limits. *=Noise Floor Measurements ( Minimum system sensitivity) Retlif Job Number R-9150-1 Retlif Testing Laboratories R Data Sheet 3 of 4 Test Method: FCC Part 15 Subpart C Radiated Emissions, Fundamental & Harmonic Emissions Customer: X-10 (USA) Job No. R-9150-1 Test Sample: RF remote Paragraph: 15.231 Model No.: UR85A FCC ID: B4SUR85A Operating Mode: Continuously Transmitting a 310 MHz Signal Technician: Peter Lananna Date: August 23, 2001 Notes: Test Distance: 3 Meters Duty Cycle:37.2 % Detector: Peak, unless otherwise specified Duty Cycle Correction: -9.2dB Test Freq. Antenna Pol./Height EUT Orientation Peak Reading Correction Factor Corrected Reading Converted Reading Avg. Limit MHz (V/H)-Meters X / Y / Z dBuV dB dBuV/m uV/m uV/m 310 H / 2.3 X 58.7 -9.2 49.5 298.5 5830 | H / 1.0 Y 60.2 -9.2 51.0 354.8 | | H / 1.8 Z 56.2 -9.2 47.0 223.9 | | V / 2.0 X 58.0 -9.2 48.8 275.4 | | V / 1.0 Y 51.0 -9.2 41.8 123.0 | 310 V / 1.5 Z 57.0 -9.2 47.8 245.5 5830 620 H / 1.0 X 40.4 -9.2 31.2 36.3* 583 | H / 1.0 Y 40.4 -9.2 31.2 36.3* | | H / 1.5 Z 40.4 -9.2 31.2 36.3* | | V / 2.3 X 40.4 -9.2 31.2 36.3* | | V / 2.3 Y 40.4 -9.2 31.2 36.3* | 620 V / 2.3 Z 40.4 -9.2 31.2 36.3* 583 930 H / 2.0 X 38.7 -9.2 29.5 29.9* 583 | H / 1.3 Y 38.7 -9.2 29.5 29.9* | | H / 1.5 Z 38.7 -9.2 29.5 29.9* | | V / 1.0 X 38.7 -9.2 29.5 29.9* | | V / 1.5 Y 38.7 -9.2 29.5 29.9* | 930 V / 1.5 Z 38.7 -9.2 29.5 29.9* 583 1240 H / 1.0 X 38.9 -9.2 29.7 30.5* 500 | H / 1.0 Y 38.9 -9.2 29.7 30.5* | | H / 1.0 Z 38.9 -9.2 29.7 30.5* | | V /1.0 X 38.9 -9.2 29.7 30.5* | | V / 1.0 Y 38.9 -9.2 29.7 30.5* | 1240 V / 1.0 Z 38.9 -9.2 29.7 30.5* 500 1550 H / 1.0 X 40.6 -9.2 31.4 37.2* 500 | H / 1.0 Y 40.6 -9.2 31.4 37.2* | | H / 1.0 Z 40.6 -9.2 31.4 37.2* | | V /1.0 X 40.6 -9.2 31.4 37.2* | | V / 1.0 Y 40.6 -9.2 31.4 37.2* | 1550 V / 1.0 Z 40.6 -9.2 31.4 37.2* 500 The frequency range was scanned from 30 MHz to 3.1 GHz. All emissions not recorded were more Than 10 dB below the specified limit. Emissions from the EUT do not exceed the specified limits. *=Noise Floor Measurements ( Minimum system sensitivity) Retlif Job Number R-9150-1 Retlif Testing Laboratories R Data Sheet 4 of 4 Test Method: FCC Part 15 Subpart C Radiated Emissions, Fundame…

Text truncated - open the document above for the full version.