B4SUR86ARemote Control

Set Up and Operating Instructions for Remote Control Model UR86A Install batteries: Open the battery compartment on the back of the remote and insert 4 AAA alkaline batteries (not supplied). Observe polarity. Setup 1.Turn on the device you want to control (TV, VCR, cable box, etc.). 2.Press and hold SETUP until the LED indicator lights steadily. Release the SETUP button. 3.Press and release mode button for the device you want to control. The LED blinks once. 4.Enter the 3 digit Code from the Library Code Table (separate sheet). The LED turns off after the last digit entered. 5.Point the remote at the device and press the POWER button. Your device should turn off. 6.Turn your device on and press CHANNEL+. If the device responds, setup is complete. PC Operation Download and install the software from www.x10.com/software. Run the program and press the PC button to access Mouse Remote features. Follow the on screen prompts in the software and select help from the on-screen menu for more information. X10 (USA) Inc. 400 Forge Way, Suite 412 Rockaway, NJ 07866 973-625-9355 UR86A-10/01 TV VCRAUX POWER CBL PLAY STOP PAUSEREC REWF.F. 213 4 5 6 789 0 MENUEXIT X1O AB CD PC ML LR F.C.C. CAUTION - THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. This equipment generates and uses radio frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturers instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for remote control security devices in accordance with the specifications in Sub-Part B of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by unplugging the equipment, try to correct the interference by one or more of the following measures. oReorient the antenna of the radio/TV experiencing the interference. oRelocate the product with respect to the radio/TV. oMove the product away from the radio/TV. oPlug the product into an outlet on a different electrical circuit from the radio/TV experiencing the interference. If necessary, consult your local dealer for additional suggestions. NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TO THE UNITS. ANY CHANGES MADE TO THE UNITS WILL VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

MCU (R008) MCU (EM78P153E) Block Diagram for MOUSE REMOTE (UR86A) Key Matrix Mouse Pad 310MHz Transmitter 310MHz

Model UR86A (VGA) Remote Control rating label 2: 1 11/5/01 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. NO SERVICEABLE PARTS INSIDE. Use Four AAA alkaline batteries. For use with VT37A VGA Video Sender. Mouse Remote Model UR86A X10.com, a division of X10 Wireless Technology, Inc. www.x10.com/support FCC ID: B4SUR86A Made in China

UR86A Operational Description The UR86A is a 310 MHz pulsed RF transmitter and an infrared remote control. The infrared remote can control a variety of TVs VCRs cable boxes etc. The 310 MHz pulsed RF transmitter can control a variety of X-10 home automation devices. The internal MCUs receive information from either the keypad or mouse pad and convert the keystrokes into a pulse code. The pulse code is then sent to the 310 MHz RF transmitter and is used to pulse modulate the 310 MHz carrier.

Retlif Testing Laboratories R Test Report No. R-9234-1 FCC ID: B4SUR86A APPLICANT X-10 (USA), Inc. 400 Forge Way, Suite 412 Rockaway, NJ 07866-2033 MANUFACTURER X-10 Electronics Shenzhen Co. Ltd. X-10 Building Labour Industrial District Shenzhen, Xixiang, Bao An Guang Dong, China, 518102 TEST SPECIFICATION:FCC Rules and Regulations Part 15, Subpart C, Para. 15.231 TEST PROCEDURE:ANSI C63.4:1992 TEST SAMPLE DESCRIPTION BRANDNAME: X-10 (USA), Inc. MODEL: UR86A TYPE: Pulsed Transmitter POWER REQUIREMENTS: 6 VDC derived from (4) new “AAA” Batteries FREQUENCY OF OPERATION: 310 MHz TESTS PERFORMED Para. 15.231(b)(1), Radiated Emissions, Fundamental and Harmonics Para. 15.231(b)(3), Radiated Emissions, Spurious Case Para. 15.231(c), Occupied Bandwidth Para. 15.35, Duty Cycle Determination REPORT OF MEASUREMENTS Applicant: X-10 (USA), Inc. Device:Pulsed Transmitter FCC ID: B4SUR86A Power Requirements: 6 VDC derived from (4) new “AAA” Batteries Applicable Rule Section:Part 15, Subpart C, Section 15.231 Retlif Testing Laboratories R Test Report No. R-9234-1 FCC ID: B4SUR86A Retlif Testing Laboratories R Test Report No. R-9234-1 FCC ID: B4SUR86A REPORT OF MEASUREMENTS (continued) TEST RESULTS 15.231 (a):This device is used as a remote control transmitter. 15.231 (a)(1) &The transmitter is manually operated and ceases transmission within 5 15.231(a)(2):seconds after deactivation. 15.231 (a)(3):The transmitter does not perform periodic transmissions. 15.231 (b):The fundamental field strength did not exceed 5833 μV/M (Average) at a test distance of 3 meters. In addition, the requirements of section 15.35 for averaging pulsed emissions and for limiting peak emissions were met. The field strength of harmonic and spurious emissions did not exceed 583 μV/M (AVERAGE). DETERMINATION OF FIELD STRENGTH LIMITS The field strength limits shown below are found in Section 15.231. Frequency Limit F1=2603750=L1 Fo=310Lo F2=47012500=L2 The formula below was utilized to determine the limits: Limit = L1 + [(Fo-F1)(L2-L1)/(F2-F1)] Solving yields: Fundamental Limit= 5833 μV/M (AVERAGE) @ 3 Meters Harmonic Limit= 583 μV/M (AVERAGE) @ 3 Meters Retlif Testing Laboratories R Test Report No. R-9234-1 FCC ID: B4SUR86A REPORT OF MEASUREMENTS (continued) DUTY CYCLE DETERMINATION The unit’s RF output was directly coupled to the input of the spectrum analyzer. The analyzer was set for a frequency span of 0Hz. The sweep time was then adjusted in order to display one full pulse train. The transmitter on time was then summed and compared to the time for one full cycle in order to obtain the duty cycle. (See plots for additional information) Transmitter On Time=17.4 milliseconds (maximum- per cycle) Transmitter Cycle Time=48 milliseconds Transmitter Duty Cycle=36.3 % CALCULATION: 1 Large Pulse = 4.3 milliseconds 21 x 625 μs (small pulse)= 13.1 milliseconds 4.3 + 13.1= 17.4 milliseconds Cycle Time=48 milliseconds Duty Cycle =17.4/48 = 36.3 % Correction Factor = 20 log(0.363) =-8.8 SPECTRUM ANALYZER DESENSITIZATION CONSIDERATIONS Due to the nature of the emissions being measured, care was taken to ensure that the resolution bandwidth of the spectrum analyzer was adequate to provide accurate measurements. The following formula was utilized: Setting pulse desensitization equal to zero and utilizing the minimum observed pulse width of 625μs yields a minimum required bandwidth of 1.067 kHz. FCC specified bandwidths of 100kHz and 1MHz were utilized below and above 1GHz, respectively. Retlif Testing Laboratories R Test Report No. R-9234-1 FCC ID: B4SUR86A GENERAL NOTES 1.All readings were taken utilizing a peak detector function at a test distance of 3 meters. 2.The duty cycle was applied to the peak readings in order to determine the average value of the emissions. 3.The frequency range was scanned from 30 MHz to 3.1 GHz. All emissions not reported were more than 20 dB below the specified limit. Retlif Testing Laboratories R Test Report No. R-9234-1 FCC ID: B4SUR86A EQUIPMENT LIST FCC15.231 Compliance testing ENTypeManufacturerDescriptionModel No.Cal DateDue Date 067Open Area Test SiteRetlif3 MeterRNY09/20/200009/20/2003 128CDouble Ridge GuideEaton Corporation1 GHz - 18 GHz9600109/21/200109/21/2002 133Broadband Pre-AmplifierElectro-Metrics10 kHz - 1 GHz, 26dBBPA-100006/13/200106/13/2002 141Spectrum AnalyzerHewlett Packard100 Hz - 40 GHz8566B07/02/200101/02/2002 141AGraphics PlotterHewlett PackardN/A7470A03/05/200103/05/2002 141BQuasi-Peak AdaptorHewlett Packard100 Hz - 1 GHz85650A02/20/200101/02/2002 206B6.0 dB AttenuatorTexscan0 - 1.0 GHzFP-50 - 6 dB06/13/200106/13/2002 543PreamplifierHewlett Packard1.0 GHz - 26.5 GHz8449B06/27/200106/27/2002 767BiconilogEMCO26 - 2000 MHz3142B08/28/200108/28/2002 Retlif Testing Laboratories R Test Report No. R-9234-1 FCC ID: B4SUR86A FCC 15.231(b) RADIATED EMISSIONS, FUNDAMENTAL & SPURIOUS CASE See separate e-file attachment named REfundharm.pdf and REspur.pdf Retlif Testing Laboratories R Test Report No. R-9234-1 FCC ID: B4SUR86A FCC 15.231(c) OCCUPIED BANDWIDTH Please refer to separate electronic file named Occbw.pdf Retlif Testing Laboratories R Test Report No. R-9234-1 FCC ID: B4SUR86A FCC 15.35 DUTY CYCLE Please refer to separate electronic file named Dutycycle.pdf Retlif Testing Laboratories R Test Report No. R-9234-1 FCC ID: B4SUR86A Test Setup Photograph Radiated Emissions Retlif Testing Laboratories R Data Sheet 1 of 4 Test Method: FCC Part 15 Subpart C Radiated Emissions, Fundamental & Harmonic Emissions Customer: X-10 (USA) Job No. R-9234-1 Test Sample: RF remote Paragraph: 15.231 Model No.: UR86A FCC ID: B4SUR86A Operating Mode: Continuously Transmitting a 310 MHz Signal Technician: Peter Lananna Date: November 5, 2001 Notes: Test Distance: 3 Meters Detector: Peak, Unless otherwise specified Test Freq. Antenna Pol./Height EUT Orientation Meter Reading Correction Factor Corrected Reading Converted Reading Peak Limit MHz (V/H)/Meters X / Y / Z dBuV dB dBuV/m uV/m uV/m 310 H / 2.3 X 65.9 -3.8 62.1 …

Text truncated - open the document above for the full version.

Retlif Testing Laboratories R Test Report No. R-9234-1 FCC ID: B4SUR86A Test Setup Photograph Radiated Emissions