BABFT0020ACD Receiver with Bluetooth

• Do not leave your mobile phone in the car. The temperature inside may be high and damage the phone.• When you dispose of your car, take care to delete all personal data that are registered in your Chevrolet AUDIO system. You should delete the following Hands-free data from the system; • Bluetooth phone data In the following conditions, the system may not function.• The mobile phone is turned off.• The current position is outside the communication area.• The mobile phone is not connected.• The mobile phone has a low battery. HANDS-FREE SYSTEM • The Bluetooth ® word mark and logos are owned by the Bluetooth Hands-free system allows you to make or receive a call without taking SIG, Inc. and use of such marks by General MOTORS LIMITED is your hands off the steering wheel by connecting your mobile phone. under license. Other trade marks and trade names are those of their This system supports Bluetooth. Bluetooth is a wireless radio data respective owners. transferring system by which you can make calls without your mobile • Compatible Bluetooth Specifications: Bluetooth Specification Ver. 1.2 phone being connected with a cable or placed on cable. or later If your mobile phone does not support Bluetooth, this system • Compatible Profiles: HFP Ver. 1.5 or later can not function. OPP Ver. 1.1 or later ATTENTION NOTE CAUTION While driving, do not use a mobile phone or connect the bluetooth phone. HANDS-FREE OPERATION ③ DISPLAY WINDOW ⑦ FUNCTION BUTTONS ① VOLUME ADJUST KNOB ② PHONE BUTTON ⑤ AUDIO BUTTON④ TUNE• FILE KNOB ⑥ MENU BUTTON ! !!! FUJITSU TEN CONFIDENTIAL ABOUT THE DISPLAY • The telephone set will be registered in the main unit automatically. When registration is completed, the message "Completed!" appear for a few seconds Reception Level Indication and " " is shown in the DISPLAY WINDOW ③ in that order. The strength of the reception is indicated in the DISPLAY WINDOW ③ (5) Press the PHONE button ② to go back to the previous mode. You cannot register the Bluetooth telephone set while driving. Park your vehicle in a secure location and select the telephone set. Bluetooth connection statusWhen a Bluetooth connection is established, " " is shown in theDISPLAY WINDOW ③ If "Failed" is displayed in the DISPLAY WINDOW ③ after entering the pass key, repeat the registration operation. REGISTERING A BLUETOOTH TELEPHONE SETRegistration is required in order to use a Bluetooth telephone set. CHANGING THE PASS KEY For details of the operation to be performed at the telephone set, refer to the instruction manual supplied with the telephone set. (1) Press the PHONE BUTTON ② to display the phone menu. (2) Press MENU BUTTON ⑥ , then press in the FUNCTION REGISTERING BLUETOOTH TELEPHONE SET FOR THE FIRST TIME BUTTON ⑦ to display Bluetooth menu. (NO PHONES CURRENTLY REGISTERED) (3) Press in the FUNCTION BUTTON ⑦ to display the (1) Press the PHONE BUTTON ② to display the phone menu. Bluetooth information of the main unit. (2) Press MENU BUTTON ⑥ , then press in the FUNCTION (4) Press in the FUNCTION BUTTON ⑦ to change the pass key. BUTTON ⑦ to display Bluetooth menu. (5) Turn the TUNE•FILE KNOB ④ to display the numeral of your (3) Press in the FUNCTION BUTTON ⑦ so that the main choice in the DISPLAY WINDOW ③ , then press the AUDIO unit will start searching for other Bluetooth devices. BUTTON ⑤ . (4) When "Connecting...", "Device Name: Chevrolet" and • Repeat the same operation until you have entered the entire pass key. "Passkey: ____" is displayed in the DISPLAY WINDOW ③ ; (6) After entering the final number of your choice, press in the use the mobile phone to pair with the main unit FUNCTION BUTTON ⑦ to save the pass key you have entered. and to enter the pass key. • The pass key number comprises of only 4 digits. • The connection method from the telephone set to the unit varies according • If you wish to change the pass key again, press and then press to the specification of your telephone set. Refer to the instruction manual in the FUNCTION BUTTON ⑦ . supplied with the telephone set (5) Press the PHONE button ② to go back to the previous mode. NOTE Indication Level ATTENTION Strong Weak BT PAIR INFO EDIT BT SAVE INFO EDIT FUJITSU TEN CONFIDENTIAL (1) Press the PHONE BUTTON ② to display the phone menu. (2) Press in the FUNCTION BUTTON ⑦ to input the number You cannot change the pass key while driving. Park your vehicle in a secure you wish to call. location and change the pass key. (3) Turn the TUNE•FILE KNOB ④ to display the numeral of your choice in the DISPLAY WINDOW ③ , then press the AUDIO BUTTON ⑤ . • Repeat the same operation until you have entered the entire number. DELETING A REGISTERED TELEPHONE SET (4) When the name or telephone number you wish to call appears in the DISPLAY WINDOW ③ , press in the FUNCTION (1) Press the PHONE BUTTON ② to display the phone menu. BUTTON ⑦ . (2) Press MENU BUTTON ⑥ , then press in the FUNCTION (5) When the person receives the call, use "hands-free" to talk. BUTTON ⑦ to display Bluetooth menu. • When you have finished the call, press in the FUNCTION BUTTON ⑦ . (3) Press in the FUNCTION BUTTON ⑦ to display the mobile phone information that is currently paired with the main unit.(4) Press in the FUNCTION BUTTON ⑦ to delete/disconnect MAKING A PHONE CALL FROM A REGISTERED NUMBER the currently paired mobile phone.(5) "Delete ok?" will appear in the DISLAY WINDOW ③ asking for (1) Press the PHONE BUTTON ② to display the phone menu. confirmation, then press in the FUNCTION BUTTON ⑦ . (2) Press in the FUNCTION BUTTON ⑦ to display all phone • When deletion is completed, BT mark " " will disappear in the numbers registered, then turn TUNE•FILE KNOB ④ to search DISPLAY WINDOW ③ . and select the number you wish to call. (5) Press the PHONE button ② to go back to the previous mode. (3) When the name or telephone number you wish to call appears in the DISPLAY WINDOW ③ , press in the FUNCTION BUTTON ⑦ . (4) When the person receives the call, use "hands-free" to talk. You cannot…

Text truncated - open the document above for the full version.

FCC ID: BABFT0020A Sheet A1 of A2 Sheets ETC Report No. : 10-08-MAS-128-08(R) ANNEX A: EXTERNAL CONSTRUCTION PHOTOS OF EUT 1. Outside view 1 of EUT 2. Outside view 2 of EUT FCC ID: BABFT0020A Sheet A2 of A2 Sheets ETC Report No. : 10-08-MAS-128-08(R) 3. Outside view 3 of EUT

FCC ID: BABFT0020A Sheet B1 of B3 Sheets ETC Report No. : 10-08-MAS-128-08(R) ANNEX B: INTERNAL CONSTRUCTION PHOTOS OF EUT 1. Inside View 1 of EUT 2. Inside View 2 of EUT FCC ID: BABFT0020A Sheet B2 of B3 Sheets ETC Report No. : 10-08-MAS-128-08(R) 3. Inside View 3 of EUT 4. Inside View 4 of EUT FCC ID: BABFT0020A Sheet B3 of B3 Sheets ETC Report No. : 10-08-MAS-128-08(R) 5. Module 6. Module

ETC Report No. : 10-08-MAS-128-08(R) Sheet 1 of 3 Sheets FCC ID. : BABFT0020A Rev. No 1.0 MAXIMUM PERMISSIBLE EXPOSURE Standard Applicable FCC RULES Section 15.247 (b)(5) : Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission's guidelines. See § 1.1307(b)(1) of this Chapter. Section 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (nW/cm 2 ) Average Time (Minutes) (A) Limits for Occupational/control Exposures 300-1500 -- -- F/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/Uncontrolled Exposures 300-1500 -- -- F/300 6 1500-100,000 -- -- 1 30 F = Frequency in MHz ETC Report No. : 10-08-MAS-128-08(R) Sheet 2 of 3 Sheets FCC ID. : BABFT0020A Rev. No 1.0 IC RULES IC Safety Code 6, Section 2.2.1 (a) A person other than an RF and microwave exposed worker shall not be exposed to electromagnetic radiation in a frequency band listed in Column 1 of Table 5, if the field strength exceeds the value given in Column 2 or 3 of Table 5, when averaged spatially and over time, or if the power density exceeds the value given in Column 4 of Table 5, when averaged spatially and over time. Calculations Friis transmission formula: P d = ( P out * G ) / ( 4 * pi * r 2 ) Where P d = power density in mW/cm 2 P out = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm The limit of P d is 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance where the P d at 20 cm is meet the limit of MPE. ETC Report No. : 10-08-MAS-128-08(R) Sheet 3 of 3 Sheets FCC ID. : BABFT0020A Rev. No 1.0 Result ： Worse case Operation Frequency (GHz) Distance (cm) Maximum Peak Output Power (dBm) Maximum Peak Output Power (mW) Antenna Gain (dBi) Power Density (mW/cm 2 ) Power Density (W/m 2 ) 2.402 20 -4.03 0.395 0.8 0.00009 0.0009 The P d at 20 cm distance calculated from the Friis transmission formula is mush smaller than the limit requirement 1 mW/cm 2 or 10W/m 2 . The Installation Manual instructs the user to install the device such that it has a separation of at least 20 cm from persons to comply with the FCC's requirements. This separation of 20 cm more than meets the FCC's and Industry Canada RF exposure requirements.

FCC ID: BABFT0020A Sheet 1 of 69 Sheets ETC Report No. : 10-08-MAS-128-08(R) Rev. No 1.0 CONFORMANCE TEST REPORT FOR FCC 47 CFR, Part 15 Subpart C Report No.: 10-08-MAS-128-08(R) Client: FUJITSU TEN LIMITED Product: CD Receiver with Bluetooth Model: FT0020A FCC ID: BABFT0020A Manufacturer/supplier: FUJITSU TEN LIMITED Issue date of the origin report 10-08-MAS-128-01: 2010/09/14 Issue date of the revision report : 2010/10/08 The test result onl y corresponds to the tested sample. It is not permitted to copy this report, in part or in full, without the permission of the test laboratory. Total number of pages of this test report: 69 pages Total number of pages of photos: External photos 2 pages Internal photos 3 pages Setup photos 1 pages Test Engineer Checked By Approved By David You James Cheng Joe Hsieh ELECTRONICS TESTING CENTER, TAIWAN NO.8, LANE 29, WENMING RD., LESHAN TSUEN, GUISHAN SHIANG, TAOYUAN COUNTY, TAIWAN 33383, R.O.C.TAIWAN, R.O.C. TEL: (03) 3276170~4 INT: +886-3-3276170~4 FAX: (03) 3276188 INT: +886-3-3276188 FCC ID: BABFT0020A Sheet 2 of 69 Sheets ETC Report No. : 10-08-MAS-128-08(R) Rev. No 1.0 Client : FUJITSU TEN LIMITED Address : 2-28, Gosho-dori, 1-chome, Hyogo-ku, kobe 652-8510 Japan Manufacturer : FUJITSU TEN LIMITED Address : 2-28, Gosho-dori, 1-chome, Hyogo-ku, kobe 652-8510 Japan EUT : CD Receiver with Bluetooth Trade name : ---- Model No. : FT0020A Power Source : 13.2Vdc battery Regulations applied : FCC 47 CFR, Part 15 Subpart C (2009) Canada RSS-210 Issue 7 (2007) / RSS-Gen Issue 2 (2007) The testing described in this report has been carried out to the best of our knowledge and ability, and our responsibility is limited to the exercise of reasonable care. This certification is not intended to believe the sellers from their legal and/or contractual obligations. The compliance test is only certified for the test equipment and the results of the testing report relate only to the item tested. The compliance test of this report was conducted in accordance with the appropriate standards. It’s not intention to assure the quality and performance of the product. This report shall not be reproduced except in full, without the approval of ETC. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. Laboratory Introduction: Electronics Testing Center, Taiwan is recognized, filed and mutual recognition arrangement as following: 1 ISO9001: TüV Product Service 2 ISO/IEC 17025: BSMI, CNLA, NCC, NVLAP, CCIBLAC, UL, Compliance 3 Filing: FCC, Industry Canada, VCCI 4 MRA: Australia, Hong Kong, New Zealand, Singapore, USA, Japan, Korea, China, APLAC through TAF 5 FCC Registration Number: 90588, 91094, 91095 h Industry Canada Site Regisitation number: IC 2949A-1 NVLAP Lab Code 200133-0 FCC ID: BABFT0020A Sheet 3 of 69 Sheets ETC Report No. : 10-08-MAS-128-08(R) Rev. No 1.0 Table of Contents Page 1 GENERAL INFORMATION ............................................................................................... 5 1.1 Product Description .............................................................................................................. 5 1.2 Characteristics of Device...................................................................................................... 5 1.3 Test Methodology................................................................................................................. 5 1.4 Modifiction List of EUT....................................................................................................... 5 1.5 Test Facility .......................................................................................................................... 5 1.6 Test Summary ....................................................................................................................... 5 2 PROVISIONS APPLICABLE .............................................................................................. 6 2.1 Definition .............................................................................................................................. 6 2.2 Requirement for Compliance................................................................................................7 2.3 Restricted Bands of Operation..............................................................................................9 2.4 Labeling Requirement .......................................................................................................... 9 2.5 User Information................................................................................................................. 10 3. SYSTEM TEST CONFIGURATION ................................................................................ 11 3.1 Justification......................................................................................................................... 11 3.2 Devices for Tested System .................................................................................................11 3.2.1 ........................................................................................................................................... 11 4 RADIATED EMISSION MEASUREMENT ..................................................................... 13 4.1 Applicable Standard ........................................................................................................... 13 4.2 Measurement Procedure .....................................................................................................13 4.3 Measuring Instrument......................................................................................................... 15 4.4 Radiated Emission Data...................................................................................................... 16 4.5 Field Strength Calculation .................................................................................................. 26 5 CONDUCTED EMISSION MEASUREMENT ..............…

Text truncated - open the document above for the full version.

FCC ID: BABFT0020A Sheet 1 of 1 Sheets ETC Report No. : 10-08-MAS-128-08(R) Photos of Radiation Measuring Setup