BABFT0023ACD Receiver with Bluetooth

• Do not leave your cellular phone in the car. The temperature inside may be high and damage the phone.• When you dispose of your car, take care to delete all personal data that are registered in your TOYOTA AUDIO system. You should delete the following Hands-free data from the system; • Bluetooth phone data In the following conditions, the system may not function.• The cellular phone is turned off.• The current position is outside the communication area.• The cellular phone is not connected.• The cellular phone has a low battery. HANDS-FREE SYSTEM • The Bluetooth ® word mark and lo g os are owned b y the Bluetooth Hands-free system allows you to make or receive a call without taking SIG, Inc. and use of such marks by TOYOTA MOTORS LIMITED is your hands off the steering wheel by connecting your cellular phone. under license. Other trade marks and trade names are those of their This system supports Bluetooth, a wireless radio data respective owners. transferring system, by which you can make calls without your cellular • Compatible Bluetooth Specifications: Bluetooth Specification Ver. 1.2 phone being connected with a cable or placed on cable. or later If your cellular phone does not support Bluetooth, this system • Compatible Profiles: HFP Ver. 1.5 or later can not function. OPP Ver. 1.1 or later CAUTION While driving, do not use a cellular phone or connect a Bluetooth phone. ATTENTION NOTE HANDS-FREE OPERATION ④ DISPLAY WINDOW ⑧ FUNCTION BUTTONS ① VOLUME KNOB ③ OFF HOOK BUTTON ⑥ ENTER ・ LIST BUTTON ⑤ TUNE• FILE KNOB ⑨ SET UP BUTTON ! ② ON HOOK BUTTON ⑦ SEEK/TRACK BUTTONS FUJITSU TEN CONFIDENTIAL ABOUT THE DISPLAY (5) When Antenna mark is displayed at the right top of the screen, the connection is completed. Reception Level Indication (6) Press the "BACK" FUNCTION BUTTON ⑧ twice to go back The strength of the reception is indicated in the DISPLAY WINDOW ④ to the previous mode. You cannot register the Bluetooth cellular phone while driving. Park your vehicle in a secure location and select the cellular phone. Bluetooth connection statusWhen a Bluetooth connection is established, " " is shown in theDISPLAY WINDOW ④ If "Failed" is displayed in the DISPLAY WINDOW ④ after entering the pass key, repeat the registration operation. REGISTERING A BLUETOOTH CELLULAR PHONERegistration is required in order to use a Bluetooth system.. CHANGING THE PASS KEY For details of the operation to be performed at the cellular phone, refer to the instruction manual supplied with the phone. (1) Press the SET UP BUTTON ⑨ to display the phone menu. (2) Select "Bluetooth" by turning the TUNE ・ FILE KNOB ⑤ , REGISTERING BLUETOOTH CELLULAR PHONE FOR THE FIRST TIME and press ENTER ・ LIST BUTTON ⑥ to display SETUP menu. (NO PHONES CURRENTLY REGISTERED) (3) Select "Set Passcode" by turning the TUNE ・ FILE KNOB ⑤ , (1) Press the SET UP BUTTON ⑨ to display the phone menu. and press ENTER ・ LIST BUTTON ⑥ to display Bluetooth menu. (2) Select "Bluetooth" by turning the TUNE ・ FILE KNOB ⑤ , and press (4) Change the pass key numbers digit by digit by turning the ENTER ・ LIST BUTTON ⑥ to display SETUP menu. TUNE ・ FILE KNOB ⑤ .The Number can be comprised of from (3) Select "BT Pairing" by turning the TUNE ・ FILE KNOB ⑤ , and press 4 to 8 digits. Press "ENTER" FUNCTION BUTTON ⑧ to complete ENTER ・ LIST BUTTON ⑥ to display Bluetooth menu. changing the pass key. (4) After "CAR AUDIO Passkey0000" is di splayed, "SEARCHING" (5) Press the "BACK" FUNCTION BUTTON ⑧ twice to go back will be shown. Perform an initial registration on a Bluetooth to the previous mode. supported cellular phone. （ Refer to the instruction manual supplied with the cellular phone. ） • The connection method from the telephone set to the unit varies according to the specification of your cellular phone. Refer to the instruction manual You cannot change the pass key while driving. Park your vehicle in a secure supplied with the phone. location and change the pass key. ATTENTION Indication Level ATTENTION NOTE Strong Weak Bluetooth BT Pairing Set Passcode BT Bluetooth BACK BACK FUJITSU TEN CONFIDENTIAL DELETING A REGISTERED CELLULAR PHONE (3) Select "Enter Phone number" by turning the TUNE ・ FILE (1) Press the SET UP BUTTON ⑨ to display the phone menu. BUTTON ⑤ , and press ENTER ・ LIST BUTTON ⑥ to display (2) Select "Bluetooth" by turning the TUNE ・ FILE KNOB ⑤ , and press PHONE menu. ENTER ・ LIST BUTTON ⑥ to display SETUP menu. (4) Turn the TUNE ・ FILE BUTTON ⑤ and "ENTER" FUNCTION (3) Select "List Phone" by turning the TUNE ・ FILE KNOB ⑤ , and press BUTTON ⑧ to enter the phone number digit by digit. ENTER ・ LIST BUTTON ⑥ to display Bluetooth menu. (5) Press OFF HOOK BUTTON ③ to make a call. (4) Select "CELL" to display the cellular phone information that is currently paired with the AUDIO unit by turning the MAKING A PHONE CALL FROM A REGISTERED NUMBER TUNE ・ FILE KNOB ⑤ . Select a desired cellular phone to be deleted. (5) Turn the TUNE ・ FILE BUTTON ⑤ and select "Delete" to delete (1) Press the SET UP BUTTON ⑨ to display the phone menu. the currently paired cellular phone. (2) Select "PHONE" and press ENTER ・ LIST BUTTON ⑥ by turning (6) "Delete a CELL ?" will appear in the DISLAY WINDOW ④ asking for the TUNE ・ FILE BUTTON ⑤ to display SETUP menu. confirmation, then press "YES" in the FUNCTION BUTTON ⑧ . (3) Select "PHONE book" and press ENTER ・ LIST BUTTON ⑥ (7) Press the "BACK" FUNCTION BUTTON ⑧ three times to by turning the TUNE ・ FILE BUTTON ⑤ to display PHONE menu. go back to the previous mode. (4) Turn the TUNE ・ FILE BUTTON ⑤ and select a phone number to call (5) Press OFF HOOK BUTTON ③ to make a call. You cannot delete the registered telephone set while driving. Park your vehicle in a secure location and delete the registered cellular phone. Phone number is not displayed while driving. Only when the vehicle is stopped or parked, it is displayed. MAKING A PHONE CALLYou can make a phone call using the phone book of the AUDIO unit, manually dialing from t…

Text truncated - open the document above for the full version.

FT0023A Label Drawing FUJITSU TEN CONFIDENTIAL

FCC & IC Label Position FCC ID: BABFT0023A IC No.: 2024B-FT0023A

MURATA CONFIDENTIAL 2009.12.15

MURATA CONFIDENTIAL 2009.12.15

Location of BT module & Antenna Antenna BT module

ETC Report No. : 10-11-MAS-259-08 Sheet 1 of 2 Sheets FCC ID. : BABFT0023A Rev. No 1.0 MAXIMUM PERMISSIBLE EXPOSURE Standard Applicable Section 15.247 (b)(5) : Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission's guidelines. See § 1.1307(b)(1) of this Chapter. Section 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (nW/cm 2 ) Average Time (Minutes) (A) Limits for Occupational/control Exposures 300-1500 -- -- F/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/Uncontrolled Exposures 300-1500 -- -- F/300 6 1500-100,000 -- -- 1 30 F = Frequency in MHz Calculations Friis transmission formula: P d = ( P out * G ) / ( 4 * pi * r 2 ) Where P d = power density in mW/cm 2 P out = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm The limit of P d is 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance where the P d at 20 cm is meet the limit of MPE. ETC Report No. : 10-11-MAS-259-08 Sheet 2 of 2 Sheets FCC ID. : BABFT0023A Rev. No 1.0 Result Operation Frequency (GHz) Distance (cm) Maximum Peak Output Power (dBm) Maximum Peak Output Power (mW) Antenna Gain (dBi) FCC Power Density (mW/cm 2 ) 2402 20 -0.89 0.815 5.44 0.0006 The P d at 20 cm distance calculated from the Friis transmission formula is mush smaller than the limit requirement 1 mW/cm 2 or 10W/m 2 . The Installation Manual instructs the user to install the device such that it has a separation of at least 20 cm from persons to comply with the FCC's requirements. This separation of 20 cm more than meets the FCC's and Industry Canada RF exposure requirements.

FCC ID: BABFT0023A Sheet 1 of 82 Sheets ETC Report No. : 10-11-MAS-259-01 Rev. No 1.0 CONFORMANCE TEST REPORT FOR FCC 47 CFR, Part 15 Subpart C Report No.: 10-11-MAS-259-01 Client: FUJITSU TEN LIMITED Product: CD Receiver with Bluetooth Model: FT0023A FCC ID: BABFT0023A Manufacturer/supplier: FUJITSU TEN LIMITED Date test item received: 2010/11/25 Date test campaign completed: 2011/02/16 Date of issue: 2011/02/16 The test result onl y corresponds to the tested sample. It is not permitted to copy this report, in part or in full, without the permission of the test laboratory. Total number of pages of this test report: 82 pages Total number of pages of photos: External photos 6 pages Internal photos 3 pages Setup photos 1 pages Test Engineer Checked By Approved By David You James Cheng Joe Hsieh ELECTRONICS TESTING CENTER, TAIWAN NO.8, LANE 29, WENMING RD., LESHAN TSUEN, GUISHAN SHIANG, TAOYUAN COUNTY, TAIWAN 33383, R.O.C.TAIWAN, R.O.C. TEL: (03) 3276170~4 INT: +886-3-3276170~4 FAX: (03) 3276188 INT: +886-3-3276188 FCC ID: BABFT0023A Sheet 2 of 82 Sheets ETC Report No. : 10-11-MAS-259-01 Rev. No 1.0 Client : FUJITSU TEN LIMITED Address : 2-28, Gosho-dori, 1-chome, Hyogo-ku, kobe 652-8510 Japan Manufacturer : FUJITSU TEN LIMITED Address : 2-28, Gosho-dori, 1-chome, Hyogo-ku, kobe 652-8510 Japan EUT : CD Receiver with Bluetooth Trade name : ---- Model No. : FT0023A Power Source : 13.2Vdc battery Regulations applied : FCC 47 CFR, Part 15 Subpart C (2009) The testing described in this report has been carried out to the best of our knowledge and ability, and our responsibility is limited to the exercise of reasonable care. This certification is not intended to believe the sellers from their legal and/or contractual obligations. The compliance test is only certified for the test equipment and the results of the testing report relate only to the item tested. The compliance test of this report was conducted in accordance with the appropriate standards. It’s not intention to assure the quality and performance of the product. This report shall not be reproduced except in full, without the approval of ETC. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. Laboratory Introduction: Electronics Testing Center, Taiwan is recognized, filed and mutual recognition arrangement as following: 1 ISO9001: TüV Product Service 2 ISO/IEC 17025: BSMI, CNLA, NCC, NVLAP, CCIBLAC, UL, Compliance 3 Filing: FCC, Industry Canada, VCCI 4 MRA: Australia, Hong Kong, New Zealand, Singapore, USA, Japan, Korea, China, APLAC through TAF 5 FCC Registration Number: 90588, 91094, 91095 h Industry Canada Site Regisitation number: IC 2949A-1 NVLAP Lab Code 200133-0 FCC ID: BABFT0023A Sheet 3 of 82 Sheets ETC Report No. : 10-11-MAS-259-01 Rev. No 1.0 Table of Contents Page 1 GENERAL INFORMATION ................................................................................................ 5 1.1 Product Description .............................................................................................................. 5 1.2 Characteristics of Device ...................................................................................................... 5 1.3 Test Methodology ................................................................................................................. 5 1.4 Modifiction List of EUT ....................................................................................................... 5 1.5 Test Facility .......................................................................................................................... 5 1.6 Test Summary ....................................................................................................................... 5 2 PROVISIONS APPLICABLE .............................................................................................. 6 2.1 Definition .............................................................................................................................. 6 2.2 Requirement for Compliance ................................................................................................7 2.3 Restricted Bands of Operation ..............................................................................................9 2.4 Labeling Requirement........................................................................................................... 9 2.5 User Information ................................................................................................................. 10 3. SYSTEM TEST CONFIGURATION................................................................................. 11 3.1 Justification ......................................................................................................................... 11 3.2 Devices for Tested System.................................................................................................. 11 4 RADIATED EMISSION MEASUREMENT ..................................................................... 13 4.1 Applicable Standard............................................................................................................ 13 4.2 Measurement Procedure .....................................................................................................13 4.3 Measuring Instrument ......................................................................................................... 15 4.4 Radiated Emission Data ...................................................................................................... 16 4.5 Field Strength Calculation .................................................................................................. 20 5 CONDUCTED EMISSION MEASUREMENT ................................................................ 21 6 ANTENNA REQUIREMENT ............................................................................................ 22 6.1 Standard Applicable ..............…

Text truncated - open the document above for the full version.

FCC ID: BABFT0023A Sheet 1 of 1 Sheets ETC Report No. : 10-11-MAS-259-01 Photos of Radiation Measuring Setup