BABTN0020ACar Audio

Index 1-Rating 2-Button Function Spec 3-Radio operation procedure 4-Operating manual (Bluetooth/Handsfree) 5-FCC Operating manual Requirement 6P Model name Model No Car Audio TN0020A Page 2P 3P 4P 5P TN0020A Operation Manual (1/6) DAB TUNING RANGE 174.928 - 239.200 MHz 1-Rating FM TUNING RANGE 12.0V (10.5～16.0V) - ground 4Ω 2.1mA or less 4.0Ａ or less (Vcc=13.2V, 0.5W output) 531 - 1602 kHz (9kHz step) 87.5 - 108 MHz (50kHz step) AM TUNING RANGE RATED VOLTAGE LOAD IMPEDANCE BACK UP CURRENT RATED CURRENT (2/6) ■AUDIO controls ④BACK Transition to previous screen ②VOL DOWN Short Push: Decrease Volume Down 1 step Long Push: Decrease Volume Down continuously ③HOME Short Push: Transition to home screen Long Push: AA/CP voice recognition 2-Button Function Spec Button No.Button Name Operation ①VOL UP Short Push: Increase Volume Up 1 step Long Push: Increase Volume Up continuously 3 4 1 2 (3/6) 【操作手順】[Operation procedure] ①起動 (ACC-ON) ACC-ON後、TOYOTA画面が表示された事を確認。 After the ACC-ON, confirm that Toyota screen is displayed. ②数秒後に"CAUTION"画面に遷移します。 The screen is changed to "CAUTION" screen after a few seconds. *初回のACC-ON時はやや時間を要します。 Note: It takes a little longer for the first time of ACC-ON. ③数秒後に”Continue”ボタンを押して、MENU画面に遷移させます。 Press the "Continue" button on the face panel after a few seconds to move MENU screen. Menu Screen Display ④画面内のラジオモードウィンドウを押すと、"FM1 "画面に遷移します。 When the Radio Mode Window on the screen is pressed,"FM1" screen is displayed. ⑤下記画面に遷移したら、”<”釦 若しくは、”>”釦を押下してください。 これで、SEEKが始まります。 Confirm that the screen is changed as below, Please push down the ”<”button or ”>”button. This will start to SEEK. ※AM/DABモードも同様の手順です。 ※Same as AM/DAB mode. 3-Radio operation procedure Press anywhere in this area Push this button Push this button (4/6) 【操作手順】[Operation procedure] ①起動 (ACC-ON) ⑦画面の”Add Device”釦を押下してください。 ACC-ON後、TOYOTA画が表示された事を確認。 Please press the ”Add Device” button of the screen After the ACC-ON, confirm that Toyota screen is displayed. ②数秒後に"CAUTION"画面に遷移します。 The screen is changed to "CAUTION" screen after a few seconds. ⑧画面の”Search Device”釦を押下してください。 *初回のACC-ON時はやや時間を要します。Please press the ”Search Device” button of the screen Note: It takes a little longer for the first time of ACC-ON. ③数秒後に”Continue”ボタンを押して、MENU画面に遷移させます。⑨下記画面に遷移したらBluetooth端末（iPhone、 iPodなど)をペアリング Press the "Continue" button on the face panel after a few seconds モードに設定してください｡ to move MENU screen. Confirm if screen is changed as below, Please set iPhone or iPod in pairing mode. Menu Screen Display ④下のスワップして、NOTIFICATION画面に遷移させます。 Swipe down on the face panel to move to Notification screen. ※Displays when you have more than one pairing equipment ※複数のペアリング機器がある場合の表示 ⑩接続したiPhone又はiPodを選択します。 Select the iPhone or iPod to connect. ⑤”Setting”ボタンを押して、SETTINGS画面に遷移させます。 Please press the "Setting" button on the face panel to move to Settings screen ※ 電話機の表示にしたがって操作してください ※ Operate the phone after the message on the screen ⑪完了すれば"Connection Completed"の画面になります｡ ”Connection Completed” is displayed if completed. ⑥”Settings”画面に遷移することを確認し、画面上の"Bluetooth"釦を選択。 Confirm if ”Settings” screen is displayed, select the ”Bluetooth” button on the display. 4-Operating manual (Bluetooth/Handsfree) Push this button Push this button Push this button Push this button Push this button (5/6) CAUTION: Radio Frequency Radiation Exposure This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated with at least 20cm and more between the radiator and person's body in normal use position. Co-location: This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 5-FCC Operating manual Requirement (6/6)

Index 1-Rating 2-Button Function Spec 3-Radio operation procedure 4-Operating manual (Bluetooth/Handsfree) 5-FCC Operating manual Requirement 6P Model name Model No Car Audio TN0020A Page 2P 3P 4P 5P TN0020A Operation Manual (1/6) 1-Rating FM TUNING RANGE 12.0V (10.5～16.0V) - ground 4Ω 2.1mA or less 4.0Ａ or less (Vcc=13.2V, 0.5W output) 531 - 1602 kHz (9kHz step) 87.5 - 108 MHz (50kHz step) AM TUNING RANGE RATED VOLTAGE LOAD IMPEDANCE BACK UP CURRENT RATED CURRENT (2/6) ■AUDIO controls ④ BACK Transition to previous screen 2-Button Function Spec Button No. Button No.Button No. Button No.Button Name Button NameButton Name Button Name ①VOL UP Short Push: Increase Volume Up 1 step Long Push: Increase Volume Up continuously Operation OperationOperation Operation ② VOL DOWN Short Push: Decrease Volume Down 1 step Long Push: Decrease Volume Down continuously ③HOME Short Push: Transition to home screen Long Push: AA/CP voice recognition 3 4 1 2 (3/6) 【操作手順】[Operation procedure] ①起動 (ACC-ON) ACC-ON後、TOYOTA画面が表示された事を確認。 After the ACC-ON, confirm that Toyota screen is displayed. ②数秒後に"CAUTION"画面に遷移します。 The screen is changed to "CAUTION" screen after a few seconds. *初回のACC-ON時はやや時間を要します。 Note: It takes a little longer for the first time of ACC-ON. ③数秒後に”Continue”ボタンを押して、MENU画面に遷移させます。 Press the "Continue" button on the face panel after a few seconds to move MENU screen. Menu Screen Display ④画面内のラジオモードウィンドウを押すと、"FM1 "画面に遷移します。 When the Radio Mode Window on the screen is pressed,"FM1" screen is displayed. ⑤下記画面に遷移したら、”<”釦 若しくは、”>”釦を押下してください。 これで、SEEKが始まります。 Confirm that the screen is changed as below, Please push down the ”<”button or ”>”button. This will start to SEEK. ※AMモードも同様の手順です。 ※Same as AM mode. 3-Radio operation procedure Press anywhere in this area Push this button Push this button (4/6) 【操作手順】[Operation procedure] ①起動 (ACC-ON) ⑦画面の”Add Device”釦を押下してください。 ACC-ON後、TOYOTA画が表示された事を確認。 Please press the ”Add Device” button of the screen After the ACC-ON, confirm that Toyota screen is displayed. ②数秒後に"CAUTION"画面に遷移します。 The screen is changed to "CAUTION" screen after a few seconds. ⑧画面の”Search Device”釦を押下してください。 *初回のACC-ON時はやや時間を要します。Please press the ”Search Device” button of the screen Note: It takes a little longer for the first time of ACC-ON. ③数秒後に”Continue”ボタンを押して、MENU画面に遷移させます。⑨下記画面に遷移したらBluetooth端末（iPhone、 iPodなど)をペアリング Press the "Continue" button on the face panel after a few seconds モードに設定してください｡ to move MENU screen. Confirm if screen is changed as below, Please set iPhone or iPod in pairing mode. Menu Screen Display ④下のスワップして、NOTIFICATION画面に遷移させます。 Swipe down on the face panel to move to Notification screen. ※Displays when you have more than one pairing equipment ※複数のペアリング機器がある場合の表示 ⑩接続したiPhone又はiPodを選択します。 Select the iPhone or iPod to connect. ⑤”Setting”ボタンを押して、SETTINGS画面に遷移させます。 Please press the "Setting" button on the face panel to move to Settings screen ※ 電話機の表示にしたがって操作してください ※ Operate the phone after the message on the screen ⑪完了すれば"Connection Completed"の画面になります｡ ”Connection Completed” is displayed if completed. ⑥”Settings”画面に遷移することを確認し、画面上の"Bluetooth"釦を選択。 Confirm if ”Settings” screen is displayed, select the ”Bluetooth” button on the display. 4-Operating manual (Bluetooth/Handsfree) Push this button Push this button Push this button Push this button Push this button (5/6) CAUTION: Radio Frequency Radiation Exposure This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated with at least 20cm and more between the radiator and person's body in normal use position. Co-location: This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 5-FCC Operating manual Requirement (6/6)

Index 1-Rating 2-Button Function Spec 3-Radio operation procedure 4-Operating manual (Bluetooth/Handsfree) 5-FCC Operating manual Requirement 6P Model name Model No Car Audio TN0020A Page 2P 3P 4P 5P TN0020A Operation Manual (1/6) 1-Rating FM TUNING RANGE 12.0V (10.5～16.0V) - ground 4Ω 2.1mA or less 4.0Ａ or less (Vcc=13.2V, 0.5W output) 530 - 1625 kHz (5kHz step) 87.5 - 108 MHz (100kHz step) AM TUNING RANGE RATED VOLTAGE LOAD IMPEDANCE BACK UP CURRENT RATED CURRENT (2/6) ■AUDIO controls ④ BACK Transition to previous screen 2-Button Function Spec Button No. Button No.Button No. Button No.Button Name Button NameButton Name Button Name ①VOL UP Short Push: Increase Volume Up 1 step Long Push: Increase Volume Up continuously Operation OperationOperation Operation ② VOL DOWN Short Push: Decrease Volume Down 1 step Long Push: Decrease Volume Down continuously ③HOME Short Push: Transition to home screen Long Push: AA/CP voice recognition 3 4 1 2 (3/6) 【操作手順】[Operation procedure] ①起動 (ACC-ON) ACC-ON後、TOYOTA画面が表示された事を確認。 After the ACC-ON, confirm that Toyota screen is displayed. ②数秒後に"CAUTION"画面に遷移します。 The screen is changed to "CAUTION" screen after a few seconds. *初回のACC-ON時はやや時間を要します。 Note: It takes a little longer for the first time of ACC-ON. ③数秒後に”Continue”ボタンを押して、MENU画面に遷移させます。 Press the "Continue" button on the face panel after a few seconds to move MENU screen. Menu Screen Display ④画面内のラジオモードウィンドウを押すと、"FM1 "画面に遷移します。 When the Radio Mode Window on the screen is pressed,"FM1" screen is displayed. ⑤下記画面に遷移したら、”<”釦 若しくは、”>”釦を押下してください。 これで、SEEKが始まります。 Confirm that the screen is changed as below, Please push down the ”<”button or ”>”button. This will start to SEEK. ※AMモードも同様の手順です。 ※Same as AM mode. 3-Radio operation procedure Press anywhere in this area Push this button Push this button (4/6) 【操作手順】[Operation procedure] ①起動 (ACC-ON) ⑦画面の”Add Device”釦を押下してください。 ACC-ON後、TOYOTA画が表示された事を確認。 Please press the ”Add Device” button of the screen After the ACC-ON, confirm that Toyota screen is displayed. ②数秒後に"CAUTION"画面に遷移します。 The screen is changed to "CAUTION" screen after a few seconds. ⑧画面の”Search Device”釦を押下してください。 *初回のACC-ON時はやや時間を要します。Please press the ”Search Device” button of the screen Note: It takes a little longer for the first time of ACC-ON. ③数秒後に”Continue”ボタンを押して、MENU画面に遷移させます。⑨下記画面に遷移したらBluetooth端末（iPhone、 iPodなど)をペアリング Press the "Continue" button on the face panel after a few seconds モードに設定してください｡ to move MENU screen. Confirm if screen is changed as below, Please set iPhone or iPod in pairing mode. Menu Screen Display ④下のスワップして、NOTIFICATION画面に遷移させます。 Swipe down on the face panel to move to Notification screen. ※Displays when you have more than one pairing equipment ※複数のペアリング機器がある場合の表示 ⑩接続したiPhone又はiPodを選択します。 Select the iPhone or iPod to connect. ⑤”Setting”ボタンを押して、SETTINGS画面に遷移させます。 Please press the "Setting" button on the face panel to move to Settings screen ※ 電話機の表示にしたがって操作してください ※ Operate the phone after the message on the screen ⑪完了すれば"Connection Completed"の画面になります｡ ”Connection Completed” is displayed if completed. ⑥”Settings”画面に遷移することを確認し、画面上の"Bluetooth"釦を選択。 Confirm if ”Settings” screen is displayed, select the ”Bluetooth” button on the display. 4-Operating manual (Bluetooth/Handsfree) Push this button Push this button Push this button Push this button Push this button (5/6) CAUTION: Radio Frequency Radiation Exposure This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated with at least 20cm and more between the radiator and person's body in normal use position. Co-location: This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 5-FCC Operating manual Requirement (6/6)

DENSO TEN Limited 2-28, Gosho-dori 1-chome, Hyogo-ku, Kobe, 652-8510 Japan Tel.: +81.78-682-2159 Fax.: +81.78-682-2169 Date: June 22, 2020 UL Verification Services Inc. 47173 Benicia Street, Fremont, CA 94538 Applicant: DENSO TEN Limited FCC ID: BABTN0020A To whom it may concern: We, the undersigned, hereby authorize Yukari Ito of Consumer Technology Division, UL Japan, Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Japan, Inc. on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. The application for the subject equipment has not been submitted to another TCB for certification. Sincerely Yours, Kaoru Abe Department General Manager Quality Assurance Group Quality Control Div Regulatory Management Dept. DENSO TEN Limited

DENSO TEN Limited 2-28, Gosho-dori 1-chome, Hyogo-ku, Kobe, 652-8510 Japan Tel.: +81.78-682-2159 Fax.: +81.78-682-2169 Request for Confidentiality Date: June 22, 2020 UL Verification Services Inc. 47173 Benicia Street, Fremont, CA 94538 Applicant : DENSO TEN Limited FCC ID : BABTN0020A To whom it may concern: Please be advised that the following information is to be held confidential on behalf of us, referring to the FCC rules 0.457 and 0.459: Block Diagram Theory of Operation Schematics The application contains technical information which we deem to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Sincerely, Kaoru Abe Department General Manager Quality Assurance Group Quality Control Div Regulatory Management Dept. DENSO TEN Limited

DENSO TEN Limited 2-28, Gosho-dori 1-chome, Hyogo-ku, Kobe, 652-8510 Japan Tel.: +81.78-682-2159 Fax.: +81.78-682-2169 Request for Short-Term Confidentiality Date: June 22, 2020 UL Verification Services Inc. 47173 Benicia Street, Fremont, CA 94538 FCC ID : BABTN0020A Applicant : DENSO TEN Limited To whom it may concern: Please be advised that the following information is to be held in confidence for 180 days from the date of the Grant of Equipment Authorization and behalf of us, referring to the FCC rules 0.457 and 0.459: External Photos Internal Photos Test Setup Photos User Manual The application contains technical information, which we deem to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Sincerely, ____________________________________ Kaoru Abe Department General Manager Quality Assurance Group Quality Control Div Regulatory Management Dept. DENSO TEN Limited

DENSO TEN Limited 2-28, Gosho-dori 1-chome, Hyogo-ku, Kobe, 652-8510 Japan Tel.: +81.78-682-2159 Fax.: +81.78-682-2169 Special Power of Attorney To whom it may concern: I, Hitoshi Itoh of DENSO TEN Limited hereby appoint Kaoru Abe of DENSO TEN Limited to represent me to act on my behalf to do any and all of the following: Sign the following documents on my behalf and apply to FCC for the products - Letter of agency and anti-drug - Confidentiality cover letters - Any other application document that requires a signature by grantee. The rights, powers and authority in fact to exercise any and all of the rights and powers herein granted shall commence and be in full force and effective from June 17, 2020 unless specifically extended or terminated by either party. Date: June 17, 2020 Place: Japan Hitoshi Itoh DENSO TEN Limited

External Photos TN0020A (RHD) □Front□Rear □Right□e □Top□oo DENSO TEN CONFIDENTIA

DENSO TEN CONFIDENTIAL LABEL IMAGE & LABEL POSITION TN0020A TYPEAM/FM Frequency band A/B/F/GAM 531 to 1602 kHz FM 87.50 to 108.00 MHz C/HAM 530 to 1625 kHz FM 87.50 to 108.00 MHz DAM 530 to 1710 kHz FM 87.90 to 108.00 MHz EAM 530 to 1620 kHz FM 76.00 to 108.00 MHz Type A/B/C/D/E AM *** to **** kHz FM **.**to ***.** MHz Type F/G/H Label Label DENSO TEN CONFIDENTIAL

Internal Photos TN0020A (RHD) 【PANEL Board】 Component sideSolder side 【MAIN Board】 Component sideSolder side 【DAB Board】 Component sideSolder side DENSO TEN CONFIDENTIAL 【BT module mounting position】 Panel AssyEnlargement 【BT Antenna position】 Panel AssyEnlargement DENSO TEN CONFIDENTIAL ・As for mount parts and parts number , refer to the 'Component layout DWG'. ・As for pattern, refer to the 'Pattern DWG'. BT module BT Antenna

Test report No. : 13198340H-C-R1 Page : 1 of 26 Issued date : October 30, 2020 FCC ID : BABTN0020A UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Report Cover Page - 13-EM-F0429 Issue # 17.0 EMI TEST REPORT Test Report No. : 13198340H-C-R1 Applicant : DENSO TEN Limited Type of EUT : Car Audio Model Number of EUT : TN0020A FCC ID : BABTN0020A Test regulation : FCC Part 15 Subpart B: 2020 ICES-003 Issue 6: 2016 (updated April 2019) Test Result : Complied (Refer to SECTION 3.2) Date of test: June 19 and 20, 2020 Representative test engineer: Ken Fujita Engineer Consumer Technology Division Approved by: Tsubasa Takayama Leader Consumer Technology Division CERTIFICATE 5107.02 The testing in which "Non-accreditation" is displayed is outside the accreditation scopes in UL Japan. There is no testing item of "Non-accreditation". 1. This test report shall not be reproduced in full or partial, without the written approval of UL Japan, Inc. 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the limits of the above re gulation. 4. The test results in this test report are traceable to the national or international standards. 5. This test report must not be used by the customer to claim product certification, approval, or endorsement by the A2LA accreditation body. 6. This test report covers EMC technical requirements. It does not cover administrative issues such as Manual or non-EMC test related Requirements. (if applicable) 7. The all test items in this test report are conducted by UL Japan, Inc. Ise EMC Lab. 8. The opinions and the interpretations to the result of the description in this report are outside scopes where UL Japan has been accredited. 9. The information provided from the customer for this report is identified in SECTION 1. 10. This report is a revised version of 13198340H-C. 13198340H-C is replaced with this report. Test report No. : 13198340H-C-R1 Page : 2 of 26 Issued date : October 30, 2020 FCC ID : BABTN0020A UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 REVISION HISTORY Original Test Report No.: 13198340H-C Revision Test report No. Date Page revised Contents - (Ori ginal) 13198340H-C July 31, 2020 - - 1 13198340H-C-R1 October 30, 2020 P.24 Deletion of Power Meter (Local ID: MPM-22) and Addition of Pre Amplifier (Local ID: MPA-22) Test report No. : 13198340H-C-R1 Page : 3 of 26 Issued date : October 30, 2020 FCC ID : BABTN0020A UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 CONTENTS PAGE SECTION 1: Customer information ...................................................................................................... 4 SECTION 2: Equipment under test (EUT) ............................................................................................ 4 SECTION 3: Test specification, procedures & results ......................................................................... 6 SECTION 4: Operation of EUT during testing ..................................................................................... 9 SECTION 5: Radiated Emission ........................................................................................................... 11 SECTION 6: Antenna Terminal ........................................................................................................... 13 APPENDIX 1: Test data ........................................................................................................................ 14 Radiated emission ............................................................................................................................. 14 Antenna Terminal Conducted Emission ........................................................................................... 22 APPENDIX 2: Test instruments ........................................................................................................... 24 APPENDIX 3: Photographs of test setup ............................................................................................. 25 Radiated Emission ............................................................................................................................ 25 Test report No. : 13198340H-C-R1 Page : 4 of 26 Issued date : October 30, 2020 FCC ID : BABTN0020A UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 SECTION 1: Customer information Compan y Name : DENSO TEN Limited Address : 2-28, Gosho-dori 1-Chome, H yogo-ku, Kobe, 652-8510 JAPAN Telephone Numbe r : +81-78-682-2159 Facsimile Numbe r : +81-78-671-7160 Contact Person : Daisuke Fukii The information provided from the customer is as follows; - Applicant, Type of EUT, Model Number of EUT, FCC ID on the cover and other relevant pages - Operating/Test Mode(s) (Mode(s)) on all the relevant pages - SECTION 1: Customer information - SECTION 2: Equipment under test (EUT) other than the Receipt Date - SECTION 4: Operation of EUT during testing * The laboratory is exempted from liability of any test results affected from the above information in SECTION 2 and 4. SECTION 2: Equipment under test (EUT) 2.1 Identification of EUT T ype : Car Audio Model Numbe r : TN0020A Serial Numbe r : Refer to SECTION 4.2 Ratin g : DC 12V Receipt Date : June 15, 2020 Countr y of Mass-production : Thailand Condition : Production prototype (Not for Sale: This sample is equivalent to mass- produced items.) Modification : No Modification by the test lab. Test report No. : 13198340H-C-R1 Page : 5 of 26 Issued date : October 30, 2020 FCC ID : BABTN0020A UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 2.2 Product Description …

Text truncated - open the document above for the full version.

Test report No. : 13198340H-C-R1 Page : 25 of 26 Issued date : October 30, 2020 FCC ID : BABTN0020A UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 APPENDIX 3: Photographs of test setup Radiated Emission (Below 1 GHz) Photo 1 Photo 2 Test report No. : 13198340H-C-R1 Page : 26 of 26 Issued date : October 30, 2020 FCC ID : BABTN0020A UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Radiated Emission (Above 1 GHz) Photo 1 Photo 2 End of Report