BBORBTM7800BLUETOOTH MODULE

Clear and specific instructions describing the conditions, limitations and procedures for third-parties to use and/or integrate the module into a host device. Grantee must demonstrate how it will retain control over the final installation of the device, such that compliance of the product is ensured: • Manual: It must be clear that manual is intended to OEM/Integrators • Does cover/or title page indicate something similar to “OEM/Integrators Installations Manual”? • Or is the content of manual clear about this? Manual must indicate • That module is limited to OEM installation ONLY • That OEM integrators is responsible for ensuring that the end-user has no manual instructions to remove or install module • That module is limited to installation in mobile or fixed applications, according to Part 2.1091(b) • Labeling instructions of finished products. Please refer to KDB784748 D01 v07, section 8. Page 6/7 last two paragraphs which include the required instructions https://apps.fcc.gov/kdb/GetAttachment.html?id=26762 example: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1” etc. The Grantee must instruct the OEM/Integrator to include the following instructions/statements in the host user’s manual (i.e. end product). • Statements required per Part 15.19 and 15.21 • End-users must be provided with transmitter/antenna installation requirements and operating conditions for satisfying RF exposure compliance: • The module is integrated with the host, the grantee (the party responsible for the module grant) shall provide guidance to the host manufacturer for compliance with the Part 15B requirements.” • § 15.21 & 15.19 Information to user. • 15.21 The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. • The OEM integrator shall include in the manual for the End User this warning statement. 15.19 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

User manual (internal Cobra document) Module description. 1. A PCB assembly that contains the BT IC, flash memory IC, antenna, voltage regulator, and connectors to interconnect to a motherboard. Use limitations 2. The assembly is designed for inclusion in Cobra radar detector products to supply the BT and laser detection functions. 3. The Bluetooth module assembly can only be used in Cobra devices designed for this particular form factor. Other form factors are not allowed without FCC and IC reauthorization. 4. Although this device is a very low output power device. The RF exposure limits we self impose are for use in mobile or fixed location products => 20 cm. 5. The BT protocols and data interface is per the manufacturer’s data sheet for the BT integrated circuit. 6. The radiated or conducted output power cannot be changed without re authorization. Module photo 1 Module photo 2

Clear and specific instructions describing the conditions, limitations and procedures for third-parties to use and/or integrate the module into a host device. Grantee must demonstrate how it will retain control over the final installation of the device, such that compliance of the product is ensured: • Manual: It must be clear that manual is intended to OEM/Integrators • Does cover/or title page indicate something similar to “OEM/Integrators Installations Manual”? • Or is the content of manual clear about this? Manual must indicate • That module is limited to OEM installation ONLY • That OEM integrators is responsible for ensuring that the end-user has no manual instructions to remove or install module • That module is limited to installation in mobile or fixed applications, according to Part 2.1091(b) • Labeling instructions of finished products. Please refer to KDB784748 D01 v07, section 8. Page 6/7 last two paragraphs which include the required instructions https://apps.fcc.gov/kdb/GetAttachment.html?id=26762 example: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1” etc. The Grantee must instruct the OEM/Integrator to include the following instructions/statements in the host user’s manual (i.e. end product). • Statements required per Part 15.19 and 15.21 • End-users must be provided with transmitter/antenna installation requirements and operating conditions for satisfying RF exposure compliance: • The module is integrated with the host, the grantee (the party responsible for the module grant) shall provide guidance to the host manufacturer for compliance with the Part 15B requirements.” • § 15.21 & 15.19 Information to user. • 15.21 The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. • The OEM integrator shall include in the manual for the End User this warning statement. 15.19 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

To Whom It May Concern: We, the Cobra Electronics Corporation, hereby request a Limited Module Approval as provided in Section 15.212 of the FCC Rules. The requirements of this section have been fulfilled as follows: 15.212(a)(1)(i); Requirement of RF Shielding: The module meets the radiated emissions limits of sections 15.209 and 15.249 of the FCC Rules without shielding. 15.212(a)(1)(ii); Requirement of Buffered Input: The module does not provide a direct data input to the modulator. 15.212(a)(1)(iii); Requirement of Power Supply Regulation: The module incorporates its own regulators, which are denoted as U1602 in the documentation. 15.212(a)(1)(iv); Antenna Requirement: The module incorporates a permanently attached antenna. 15.212(a)(1)(v); Stand-Alone Test Configuration: The module was tested in a standalone test configuration as described in the test report. 15.212(a)(1)(vi)(A); Labeling Requirement: The module will be labeled with its own FCC identification number, and the device into which the module is installed will display a label referring to the enclosed module. A picture of the external label is included with the documentation. 15.212(a)(1)(vii); Operating Requirements: The module meets the specific rules for this type of transceiver, and the User’s Manual contains instructions for maintaining compliance. Further Cobra expects to only use the module in it’s own products. 15.212(a)(1)(vii); RF Exposure: The module complies with RF exposure requirements as demonstrated in the test report. Sincerely, Jeff Sterling Director, Microwave Engineering Cobra Electronics Corporation

Equipment Authorization Division Office of Engineering and Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Ref: FCC ID: BBOSPX7800 BBORBTM7800 Request for Confidentiality Dear Sirs: With regard to the referenced application, Cobra Electronics Corp. is requesting confidentiality of certain sections of the accompanying documents. The documents for which Cobra Electronics Corp. is requesting confidentiality are: SPX 7800 Block Diagram SPX 7800 Circuits (Schematics) SPX 7800 Theory of operation This request is made under the provisions of Section 0.457(d) of the Commission’s Rules, and Section 552(b)(4) of the Freedom of Information Act. The material for which confidentiality is requested falls within the scope of Section 552(b)(4) as trade secrets and includes material covered by Section 0.459 of the Commission’s Rules. Pursuant to DA 04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below until the end of March, 2013 (expected ship date): SPX 7800 External Photos SPX 7800 Test Setup Photos SPX 7800 Manual SPX 7800 Internal Photos Sincerely, Jeff Sterling Director, Microwave Engineering

APPLICANT: COBRA ELECTRONICS CORPORATION FCC ID: BBORBTM7800 EXTERNAL PHOTOS

APPLICANT: COBRA ELECTRONICS CORPORATION FCC ID: BBORBTM7800 EXTERNAL PHOTOS

FCC PART 15.249 TEST REPORT UNLICENSED INTENTIONAL RADIATOR Applicant COBRA ELECTRONICS CORPORATION Address 6500 WEST CORTLAND STREET CHICAGO IL 60707 USA FCC ID BBORBTM7800 Model Number RBTM7800 Product Description BLUETOOTH MODULE Date Sample Received 7/17/2013 Date Tested 7/25/2013 Tested By John A. Day Approved By John A. Day Report Number 1232AUT13TestReport.docx Test Results PASS FAIL THE ATTACHED REPORT SHALL NOT BE REPRODUCED EXCEPT IN FULL WITHOUT THE WRITTEN APPROVAL OF TIMCO ENGINEERING, INC. Testing Certificate #0955-01 849 NW State Road 45 Newberry, FL 32669 USA Ph: 888.472.2424 or 352.472.5500 Fax: 352.472.2030 Email: [email protected] Website: www.timcoengr.com APPLICANT: COBRA ELECTRONICS CORPORATION FCC ID: BBORBTM7800 REPORT #: C\COBRA\1232AUT13\1232AUT13TestReport.docx Page 2 of 16 Mdea5.11.2012 TABLE OF CONTENT GENERAL REMARKS ................................................................................................................. 3 GENERAL INFORMATION .......................................................................................................... 4 EMC EQUIPMENT LIST .............................................................................................................. 5 TEST PROCEDURES .................................................................................................................. 7 RADIATION INTERFERENCE ..................................................................................................... 8 OCCUPIED BANDWIDTH ........................................................................................................... 9 BAND EDGE COMPLIANCE ..................................................................................................... 10 DUTY CYCLE ........................................................................................................................... 15 POWER LINE CONDUCTED INTERFERENCE ........................................................................... 16 APPLICANT: COBRA ELECTRONICS CORPORATION FCC ID: BBORBTM7800 REPORT #: C\COBRA\1232AUT13\1232AUT13TestReport.docx Page 3 of 16 Mdea5.11.2012 GENERAL REMARKS The attached report shall not be reproduced except in full without the written permission of Timco Engineering Inc. Summary The device under test does: fulfill the general approval requirements as identified in this test report not fulfill the general approval requirements as identified in this test report Attestations This equipment has been tested in accordance with the standards identified in this test report. To the best of my knowledge and belief, these tests were performed using the measurement procedures described in this report. All instrumentation and accessories used to test products for compliance to the indicated standards are calibrated regularly in accordance with ISO 17025 requirements. Certificate # 0955-01 I attest that the necessary measurements were made, under my supervision, at: Timco Engineering Inc. 849 NW State Road 45 Newberry, Fl 32669 Authorized Signatory Name: John A. Day Engineering Project Manager Date: 7/31/2013 APPLICANT: COBRA ELECTRONICS CORPORATION FCC ID: BBORBTM7800 REPORT #: C\COBRA\1232AUT13\1232AUT13TestReport.docx Page 4 of 16 Mdea5.11.2012 GENERAL INFORMATION DUT Specification The test results relate only to the items tested. Applicable Standard Part 15.249, RSS-210, RSS-GEN DUT Description BLUETOOTH MODULE FCC ID BBORBTM7800 Model Number RBTM7800 Operating Frequency TX: 2402 - 2480 RX: Same No. of Channels 79 Modulations GFSK DUT Power Source 110–120Vac/50– 60Hz DC Power Battery Operated Exclusively Test Item Prototype Pre-Production Production Type of Equipment Fixed Mobile Portable Antenna Connector FCC Rules require that the antenna connector be unique. Test Facility Timco Engineering Inc. located at 849 NW State Road 45 Newberry, FL 32669 USA. Test Conditions Temperature: 26ºC Relative humidity: 50% Test Exercise The DUT was placed in continuous transmit mode of operation. Modifications Test Supporting Equipment Supporting Device Manufacturer Model / FCC ID Serial Number N/A APPLICANT: COBRA ELECTRONICS CORPORATION FCC ID: BBORBTM7800 REPORT #: C\COBRA\1232AUT13\1232AUT13TestReport.docx Page 5 of 16 Mdea5.11.2012 EMC EQUIPMENT LIST Device Manufacturer Model Serial Number Cal/Char Date Due Date 3/10-Meter OATS TEI N/A N/A 12/31/11 12/31/13 3-Meter OATS TEI N/A N/A 12/31/11 12/31/13 Antenna: Passive Loop EMC Test Systems EMCO 6512 9706-1211 06/14/12 06/14/14 Frequency Counter HP 5385A 2730A03025 08/17/11 08/17/13 Frequency Counter HP 5352B 2632A00165 06/26/13 06/26/15 Digital Multimeter Fluke 77 43850817 02/22/12 02/22/14 Digital Multimeter Fluke FLUKE-77-3 79510405 06/20/13 06/20/15 Frequency Counter HP 5385A 3242A07460 06/16/13 06/16/15 Antenna: Active Loop ETS-Lindgren 6502 00062529 09/23/10 09/23/13 Antenna: Double- Ridged Horn Electro- Metrics RGA-180 2319 06/19/12 06/19/14 LISN Electro- Metrics ANS-25/2 2604 10/28/11 10/28/13 LISN Electro- Metrics EM-7820 2682 02/26/13 02/26/15 DC Power Supply HP 6264B 05/06/13 05/06/15 3-Meter Semi- Anechoic Chamber Panashield N/A N/A 12/31/11 12/31/13 Temperature Chamber Tenney Engineering TTRC 11717-7 07/03/12 07/03/14 Antenna: Biconnical Electro- Metrics BIA-25 1171 06/13/12 06/13/14 Temperature Chamber Thermotron Corp. S1.2 Mini Max 25-1420-09 07/03/12 07/03/14 Antenna: Log-Periodic Electro- Metrics LPA-25 1122 05/09/13 05/09/15 Digital Multimeter Fluke 77 35053830 09/09/11 09/09/13 Antenna: Biconnical Eaton 94455-1 1096 05/10/13 05/10/15 APPLICANT: COBRA ELECTRONICS CORPORATION FCC ID: BBORBTM7800 REPORT #: C\COBRA\1232AUT13\1232AUT13TestReport.docx Page 6 of 16 Mdea5.11.2012 TEST EQUIPMENT LIST CONTD. Device Manufacturer Model Serial Number Cal/Char Date Due Date Analyzer Tan Tower Preamplifier HP 8449B-H02 3008A00372 10/28/11 10/28/13 Analyzer Tan Tower Quasi- Peak Adapter HP 85650A 3303A01690 10/28/11 10/28/13 Analyzer Tan Tower RF Preselector HP 85685A 3221A01400 10/28/11 10/2…

Text truncated - open the document above for the full version.