BBORBTM900BLUETOOTH MODULE

User manual (internal Cobra document) Module description. 1. A PCB assembly that contains the BT IC, flash memory IC, antenna, voltage regulator, and connectors to interconnect to a motherboard. Use limitations 2. The assembly is designed for inclusion in Cobra radar detector products to supply the BT and laser detection functions. 3. The Bluetooth module assembly can only be used in Cobra devices designed for this particular form factor. Other form factors are not allowed without FCC and IC reauthorization. 4. Although this device is a very low output power device. The RF exposure limits we self impose are for use in mobile or fixed location products => 20 cm. 5. The BT protocols and data interface is per the manufacturer’s data sheet for the BT integrated circuit. 6. The radiated or conducted output power cannot be changed without re authorization. Module photo 1 Module photo 2

Equipment Authorization Division Office of Engineering and Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Ref: FCC ID: BBOIRAD900 BBORBTM900 Request for Confidentiality Dear Sirs: With regard to the referenced application, Cobra Electronics Corp. is requesting confidentiality of certain sections of the accompanying documents. The documents for which Cobra Electronics Corp. is requesting confidentiality are: iRad 900 Block Diagram iRad 900 Circuits (Schematics) iRad 900 Theory of operation This request is made under the provisions of Section 0.457(d) of the Commission’s Rules, and Section 552(b)(4) of the Freedom of Information Act. The material for which confidentiality is requested falls within the scope of Section 552(b)(4) as trade secrets and includes material covered by Section 0.459 of the Commission’s Rules. Pursuant to DA 04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below until the end of April, 2013 (expected ship date): iRad 900 External Photos iRad 900 Test Setup Photos iRad 900 Manual iRad 900 Internal Photos Sincerely, Jeff Sterling Director, Microwave Engineering

APPLICANT: COBRA ELE CTRONICS CORP. FCC ID: BBORBTM900 IC: 906B-RBTM900 PHOTOS

APPLICANT: COBRA ELE CTRONICS CORP. FCC ID: BBORBTM900 IC: 906B-RBTM900 PHOTOS

FCC PART 15.249 AND IC RSS-210 issue 8 TEST REPORT UNLICENSED INTENTIONAL RADIATOR Applicant COBRA ELECTRONICS CORPORATION Address 6500 WEST CORTLAND STREET CHICAGO IL 60707 USA FCC ID BBORBTM900 IC: 906A-RBTM900 Model Number RBTM900 Product Description BLUETOOTH MODULE Date Sample Received 1/29/2013 Date Tested 2/5/2013 Tested By Joe Scoglio Approved By Mario de Aranzeta Report Number 166AUT13TestReport.doc Test Results PASS FAIL THE ATTACHED REPORT SHALL NOT BE REPRODUCED EXCEPT IN FULL WITHOUT THE WRITTEN APPROVAL OF TIMCO ENGINEERING, INC. Testing Certificate #0955-01 849 NW State Road 45 Newberry, FL 32669 USA Ph: 888.472.2424 or 352.472.5500 Fax: 352.472.2030 Email: [email protected] Website: www.timcoengr.com APPLICANT: COBRA ELECTRONICS CORPORATION FCC ID: BBORBTM900 REPORT #: C\COBRA\166AUT13\166AUT13TestReport.doc Page 2 of 15 Mdea5.11.2012 TABLE OF CONTENT GENERAL REMARKS ................................................................................................................. 3 GENERAL INFORMATION .......................................................................................................... 4 EMC EQUIPMENT LIST .............................................................................................................. 5 TEST PROCEDURES .................................................................................................................. 6 RADIATION INTERFERENCE ..................................................................................................... 7 OCCUPIED BANDWIDTH ........................................................................................................... 8 BAND EDGE COMPLIANCE ....................................................................................................... 9 POWER LINE CONDUCTED INTERFERENCE ........................................................................... 15 APPLICANT: COBRA ELECTRONICS CORPORATION FCC ID: BBORBTM900 REPORT #: C\COBRA\166AUT13\166AUT13TestReport.doc Page 3 of 15 Mdea5.11.2012 GENERAL REMARKS The attached report shall not be reproduced except in full without the written permission of Timco Engineering Inc. Summary The device under test does: fulfill the general approval requirements as identified in this test report not fulfill the general approval requirements as identified in this test report Attestations This equipment has been tested in accordance with the standards identified in this test report. To the best of my knowledge and belief, these tests were performed using the measurement procedures described in this report. All instrumentation and accessories used to test products for compliance to the indicated standards are calibrated regularly in accordance with ISO 17025 requirements. Certificate # 0955-01 I attest that the necessary measurements were made, under my supervision, at: Timco Engineering Inc. 849 NW State Road 45 Newberry, Fl 32669 Authorized Signatory Name: Mario de Aranzeta C.E.T. Compliance Engineer/ Lab. Supervisor Date: 2/5/2013 APPLICANT: COBRA ELECTRONICS CORPORATION FCC ID: BBORBTM900 REPORT #: C\COBRA\166AUT13\166AUT13TestReport.doc Page 4 of 15 Mdea5.11.2012 GENERAL INFORMATION DUT Specification The test results relate only to the items tested. Applicable Standard Part 15.249 DUT Description BLUETOOTH MODULE FCC ID BBORBTM900 Model Number RBTM900 Operating Frequency TX: 2400 MHz RX: Same No. of Channels 79 DUT Power Source 110–120Vac/50– 60Hz DC Power Battery Operated Exclusively Test Item Prototype Pre-Production Production Type of Equipment Fixed Mobile Portable Antenna Connector FCC Rules require that the antenna connector be unique. Test Facility Timco Engineering Inc. located at 849 NW State Road 45 Newberry, FL 32669 USA. Test Conditions Temperature: 26ºC Relative humidity: 50% Test Exercise The DUT was placed in continuous transmit mode of operation. Modifications none Test Supporting Equipment Supporting Device Manufacturer Model / FCC ID Serial Number N/A APPLICANT: COBRA ELECTRONICS CORPORATION FCC ID: BBORBTM900 REPORT #: C\COBRA\166AUT13\166AUT13TestReport.doc Page 5 of 15 Mdea5.11.2012 EMC EQUIPMENT LIST Device Manufacturer Model Serial Number Cal/Char Date Due Date 3/10-Meter OATS TEI N/A N/A 12/31/11 12/31/13 Antenna: Passive Loop EMC Test Systems EMCO 6512 9706-1211 06/14/12 06/14/14 Frequency Counter HP 5352B 2632A00165 06/22/11 06/22/13 Digital Multimeter Fluke FLUKE-77-3 79510405 06/13/11 06/13/13 Frequency Counter HP 5385A 3242A07460 06/22/11 06/22/13 Antenna: Active Loop ETS-Lindgren 6502 00062529 09/23/10 09/23/13 Analyzer Open- Frame Tower Preamplifier HP 8449B 3008A01075 07/22/09 09/15/13 Antenna: Double-Ridged Horn Electro- Metrics RGA-180 2319 06/19/12 06/19/14 DC Power Supply HP 6264B 03/21/11 03/21/13 3-Meter Semi- Anechoic Chamber Panashield N/A N/A 12/31/11 12/31/13 Temperature Chamber Tenney Engineering TTRC 11717-7 07/03/12 07/03/14 Antenna: Biconnical Electro- Metrics BIA-25 1171 06/13/12 06/13/14 Antenna: Log- Periodic Electro- Metrics LPA-25 1122 05/04/11 05/04/13 Antenna: Biconnical Eaton 94455-1 1096 05/04/11 05/04/13 Analyzer Tan Tower Preamplifier HP 8449B-H02 3008A00372 10/28/11 10/28/13 Analyzer Tan Tower Quasi- Peak Adapter HP 85650A 3303A01690 10/28/11 10/28/13 Analyzer Tan Tower RF Preselector HP 85685A 3221A01400 10/28/11 10/28/13 Analyzer Tan Tower Spectrum Analyzer HP 8566B Opt 462 3138A07786 3144A20661 10/28/11 10/28/13 Antenna: Log- Periodic Eaton 96005 1243 05/31/11 05/31/13 APPLICANT: COBRA ELECTRONICS CORPORATION FCC ID: BBORBTM900 REPORT #: C\COBRA\166AUT13\166AUT13TestReport.doc Page 6 of 15 Mdea5.11.2012 TEST PROCEDURES Radiation Interference: ANSI C63.4-2003 using a spectrum analyzer, a preselector, a quasi- peak adapter, and an appropriate antenna. The analyzer was calibrated in dB above a microvolt at the output of the antenna. The resolution bandwidth was 100 kHz with an appropriate sweep speed and the video bandwidth was 300 kHz up to 1 GHz and 1 MHz with a video BW of 3 MH…

Text truncated - open the document above for the full version.