BBP-RFAPL03Color Copier

2. Connecting the Machine This chapter describes how to connect the machine to the network and specify the network settings. Connecting to the Interface This section explains how to identify the machine's interface and connect the machine according to the network environment. • A network interface cable with a ferrite core must be used for RF interference suppression. BZU006 1 2 3 4 5 1. Slot A Install an optional interface board in this slot. The slot can accommodate one of the following interface boards: • IEEE1284 interface board: Required if you want to connect an IEEE 1284 cable to this machine. When installed in Slot A, this board allows you to connect the machine to a computer through an IEEE 1284 cable. • Wireless LAN interface unit: Required if you want to connect this machine to a wireless LAN. When installed in Slot A, this unit allows you to connect the machine to an IEEE 802.11 a or IEEE 802.11 b/g wireless LAN. • Bluetooth interface unit: Required if you want to give the machine Bluetooth capability. When installed in Slot A, this unit allows the machine to communicate via Bluetooth with an external device. 2. USB 2.0 [Type B] port Port for connecting the USB2.0 [Type B] interface cable 3. 10BASE-T/100BASE-TX port Port for connecting the 10BASE-T or 100BASE-TX cable 75 2 4. USB Host Interface Port for connecting the USB interface cable Use this interface to connect the machine to a card authentication device or memory card reader. 5. Gigabit Ethernet port (optional) Port for using the 1000BASE-T, 100BASE-TX, or 10BASE-T cable • Slot A can contain one module only: You can install only one IEEE 1284 interface board, one Wireless LAN interface unit, or one Bluetooth interface unit at a time in this slot. • The Ethernet and Gigabit Ethernet port cannot be used simultaneously. If the optional Gigabit Ethernet board is installed, connect the Ethernet cable to the port on the Gigabit Ethernet board Communication with the machine will fail if cables are connected to both ports simultaneously. Connecting to the Ethernet Interface This section describes how to connect an Ethernet cable to the Ethernet interface. • If the main power switch is on, turn it off. • Use the following Ethernet cables. • Unshielded Twisted Pair Cable (UTP) or Shielded Twisted Pair Cable (STP) and Category type 5 or more 1. Make a loop 5 cm (2.1 inch) (1) from the end of the Ethernet cable and attach the included ferrite core to the loops as shown. 1 BZU007 2. Make sure the main power is switched off. 2. Connecting the Machine 76 2 3. Connect the Ethernet interface cable to the 10BASE-T/100BASE-TX port. BZU008 4. Connect the other end of the Ethernet interface cable to a network connection device such as a hub. 5. Turn on the main power switch of the machine. BZU009 1 2 1. Indicator (orange) When 100BASE-TX is operating, the LED is lit orange. When 10BASE-T is operating or the machine is not connected to the network, it is turned off. 2. Indicator (green) When 10BASE-T is operating, the LED is lit green. When 100BASE-TX is operating or the machine is not connected to the network, it is turned off. • For details about how to turn on the main power switch, see "Turning On the Power", About This Machine. • For details about installing the printer driver, see "Preparing the Machine", Printer Reference. Connecting to the Gigabit Ethernet Interface This section describes how to connect the Ethernet interface cable to the Gigabit Ethernet port. Connecting to the Interface 77 2 • If the main power switch is on, turn it off. • Use the following Ethernet cables. • When using 100BASE-TX/10BASE-T: Unshielded Twisted Pair Cable (UTP) or Shielded Twisted Pair Cable (STP) and Category type 5 or more • When using 1000BASE-T: Unshielded Twisted Pair Cable (UTP) or Shielded Twisted Pair Cable (STP) and Category type 5e or more 1. Make loops 5 cm (2.1 inch) (1) from the end of each Ethernet cable and attach included ferrite cores to each loop as shown. 1 1 BZU010 2. Make sure the main power is switched off. 2. Connecting the Machine 78 2 3. Connect the Ethernet interface cable to the Gigabit Ethernet port. BZU011 4. Connect the other end of the Ethernet interface cable to a network connection device such as a hub. 5. Turn on the main power switch of the machine. BZU012 3 2 1 1. Indicator (orange) When 100BASE-T is operating, the LED is lit orange. When 10BASE-TX is operating or the machine is not connected to the network, it is turned off. 2. Indicator (green) When 10BASE-TX is operating, the LED is lit green. When 100BASE-T is operating or the machine is not connected to the network, it is turned off. 3. Indicators (both orange and green) When 1000BASE-T is operating, both LED are lit. • For details about how to turn on the main power switch, see "Turning On the Power", About This Machine. • For details about installing the printer driver, see "Preparing the Machine", Printer Reference. Connecting to the Interface 79 2 Connecting to the USB (Type B) Interface This section describes how to connect the USB2.0 (Type B) interface cable to the USB2.0 port. • Properly shielded and grounded cables and connectors must be used for connections to a host computer (and/or peripheral) in order to meet emission limits. 1. Connect the USB2.0 (Type B) interface cable to the USB2.0 port. BZU013 2. Connect the other end to the USB2.0 port on the host computer. • This machine does not come with a USB interface cable. Make sure you purchase the appropriate cable for the machine and your computer. • The USB2.0 interface board is supported by Windows 2000/XP/Vista/7, Windows Server 2003/2003 R2/2008/2008 R2, Mac OS X 10.3.3 or higher. • To use Macintosh, the machine must be equipped with the optional PostScript 3 unit. When used with Mac OS X 10.3.3 or higher, a transfer speed of USB2.0 is supported. • For details about installing the printer driver, see "Preparing the Machine", Printer Reference. Connecting a Device to the Machine's USB Host Inter…

Text truncated - open the document above for the full version.

@hkma^\hib^kpbmahnmZgr_bgbla^k +( GZd^mphahe^lbgma^l\Zgg^ke^_m\ho^k( ,( ;mmZ\ama^[kZ\d^mU;W^g\ehl^]pbmama^_Zqngbm"q,4G-q+,#Zllahpg( -( L^fho^ma^eZ[^eU<W_khfma^aZg]l^m\kZ]e^U=W(;mmZ\ama^\kZ]e^U=Wmhma^[kZ\d^mU;W"q,4G- q2#&Zg]ma^gk^ieZ\^ma^eZ[^eU<W( .( CglmZeema^aZg]l^mU>Whgma^\kZ]e^U=W( /( ;mmZ\ama^_^kkbm^\hk^U?Wmhma^\Z[e^(Na^e^g`maU@Wfnlm[^3*ff( 0( ;mmZ\ama^mph\eZfilUAWZllahpg( 1( Fbg^ma^\Z[e^UBWZllahpg"=q,#( 2( =hgg^\mma^\Z[e^UBWmhma^N?FcZ\dZmma^k^Zkh_ma^fZ\abg^( @hkma^\hib^kpbmaZ_bgbla^k +(CglmZeeZmbhgJkh\^]nk^ +0 1

Installation Procedure Before installing this fax unit: ƒ Print out all data in the printer buffer. ƒ Turn off the main power switch and disconnect the power cord and the network cable. Installation Installation-2 1. Remove the controller board [A] ( x 5). 2. Attach the FCU I/F board bracket [A] to the controller board ( x 2). Installation Installation-3 3. Attach the FCU I/F board [A] to the FCU I/F board bracket ( x 4). 4. Attach the support bracket [A] to the controller box ( x 2). 5. Remove the “TEL” and “LINE1” covers with a screw driver. 6. Install the FCU [A] to the controller board ( x 4). 7. Install the speaker [A] to the controller box (x 2) and connect the speaker cable [B] with the speaker relay cable [C] ( x 3). Installation Installation-4 8. Connect the two modular harnesses [A] [B] to the modular bracket [C]. 9. Connect the two modular harnesses [A] [B] to the FCU. 10. Attach the modular bracket [A] to the controller box (x 1). Installation Installation-5 11. Switch the MBU battery jumper switch [A] to “ON” position. Make sure that the MBU board is firmly connected to the FCU. 12. Reinstall the controller box. 13. Attach the handset support bracket and handset bracket to the copier, and then connect the handset cord with the ferrite core to the "TEL" jack if you install the handset to the machine. For details, refer to the "Hand Set Installation" in the Service Manual for the Fax Unit (D393). 14. Attach the ferrite core to the telephone cord. 15. Connect the telephone cord to the "LINE 1" jack. Installation Installation-6 16. Replace bottom from the third key-slot cover [A] to the fax key [B]. 17. Attach the Multi-Language Decals [C] (EU only). 18. Attach the decal [A] (SUPER G3) to the front door. 19. Attach the serial number decal under the copier serial number decal on the rear cover of the machine. 20. Attach FCC decal on the rear cover of the machine (NA only). 21. Put the power plug into the outlet and turn on the main power of the machine. Make sure that the outlet is grounded. "SRAM formatted" shows on the operation panel after you have turned the main switch on. Turn the main switch off and on again for normal use. 22. Make sure that the date and time are correctly set. Installation Installation-7 G3 Interface Unit (D393) Component Check Check the quantity and condition of the components against the following list. No. Description Q’ty 1 SG3 Interface Unit 1 2 Modular Bracket for SG3 1 3 Clamp 2 4 Clamp 4 5 Screw: M3x6 6 6 Ferrite Core 1 7 Telephone Cable (NA only) 1 8 Flat Cable 1 9 Harness 1 10 EMC Address Decal (EU only)1 11 FCC Decal (NA only) 1 Installation Procedure Before installing this optional unit: ƒ Print out all data in the printer buffer. ƒ Turn off the main switch and disconnect the power cord and the network cable. You can add two more SG3 boards to this model. Follow the procedures for adding the single SG3 board installation or double SG3 boards installation as a customer Installation Installation-8 needs. For Installing the single G3 Board 1. Remove the controller box [A] ( x 5). 2. Attach one end (short length) of the flat cable [A] to the connector [B] of the FCU board. 3. Hold the flat cable with two clamps and pass the other end of the flat cable through the cutout as shown above. Installation Installation-9 4. Connect the SG3 interface unit [A] to the controller board [B] with the flat cable ( x 4). 5. Attach four clamps to the brackets. 6. Remove the "LINE2" cover with a screwdriver. Installation Installation-10 7. Attach the socket of harness [A] (LINE2) to the modular bracket [B] for SG3. 8. Connect the harness [A] to the SG3 interface unit [B] ( x 4). 9. Attach the modular bracket for SG3 to the controller box ( x 2). 10. Reinstall the controller box. For Installing the Double G3 Boards 1. Remove one of SG3 boards from the SG3 interface units and then attach the SG3 board to the other SG3 interface unit ( x 2). 2. Remove the controller box. Installation Installation-11 3. Attach one end (short length) of the flat cable [A] to the connector [B] of the FCU board. 4. Hold the flat cable with two clamps and pass the other end of the flat cable through the cutout as shown above. 5. Remove the "LINE2" cover and "LINE3" cover with a screwdriver. 6. Connect the SG3 interface unit [A] to the controller board [B] with the flat cable ( x 4). Installation Installation-12 7. Attach the socket of harness [A] (LINE2) and the socket of harness [C] (LINE3) to the modular bracket for SG3. 8. Connect the harness [A] (LINE2) to the first SG3 board ¶ and the harness [C] (LINE3) to the second SG3 board · ( x 4). 9. Attach the modular bracket for SG3 to the controller box ( x 2). 10. Reinstall the controller box. 11. Attach the ferrite core to the telephone cord for single SG3 board installation, or the two ferrite cores to the telephone cords for double-SG3 board installation. 12. Connect the telephone cord to the "LINE 2" jack for single SG3 board installation, or connect the telephone cords to the "LINE2" and "LINE3" jacks for double-SG3 board installation. 13. Connect the power plug to a power outlet and turn on the main power switch. 14. Enter the service mode. Set bit 1 of communication switch 16 to “1” (SP1-104-023). 15. Set bit 3 of communication switch 16 to "1" (SP1-104-023) if you have installed two SG3 boards. 16. Exit the service mode. 17. Turn the main power switch off and on. 18. Print out the system parameter list. Then check that “G3” shows as an option. 19. Set up and program the items required for PSTN-2 communications. Installation Installation-13 Fax Unit Options Memory Unit (G578) 1. Rear cover (* "Installation Procedure" in the "Fax Unit (D393)") 2. Controller box left cover (* "Installation Procedure" in the "Fax Unit (D393)") 3. Intall the memory option [A] to the FCU. 4. Re-aasemble the machine Handset (B433) The optional handset is available for the U.S. version only. 1. Remove the scanner left cover [A] ( x 2). Ins…

Text truncated - open the document above for the full version.

Oper ating Instr uctions About This Machine Paper type: OK Prince Eco G100(55kg), Paper Thickness=0.08 mm // Pages in book=212 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 8.48 mm Simple Search Getting Started Adding Paper Adding Toner and Staples Entering Text On-screen Operating Instructions Remarks Appendix 1 2 3 4 5 6 7 8 Read this manual carefully before you use this machine and keep it handy for future reference. F or safe and correct use, be sure to read the Safety Inf or mation in this manual before using the machine. About This Machine Operating Instructions About This Machine Oper ating Instr uctions Type for C9155G/LD655CG/Aficio MP C5501G Type for C9145G/LD645CG/Aficio MP C4501G Type for C9135G/LD635CG/Aficio MP C3501G Type for C9155/LD655C/Aficio MP C5501 Type for C9145/LD645C/Aficio MP C4501 Type for C9135/LD635C/Aficio MP C3501 Type for C9130/LD630C/Aficio MP C3001 Type for C9130G/LD630CG/Aficio MP C3001G Pr inted in China D088-7603ENUS D0887603 Documentation for This Machine About This Machine (This manual) Troubleshooting Copy and Document Server Reference Using the various copier functions Using the Document Server functions Changing the default settings of the copier and Document Server functions, and related information Facsimile Reference Sending and receiving faxes Using the fax function through a computer Changing the default settings of the fax function, and related information Printer Reference Installing the driver for the printer function Changing the default settings of the printer function, and related information Scanner Reference Sending scan files Storing scan files Changing the default settings of the scanner function, and related information Network and System Settings Reference Connecting to a network Registering addresses for fax/scanner functions Changing the default settings of the system, and related information Security Reference PostScript 3 Supplement VM Card Extended Feature Settings Device Reference VM Card Extended Feature Settings Web Reference Quick Reference Copy Guide Quick Reference Printer Guide Quick Reference Fax Guide Quick Reference Scanner Guide App2Me Start Guide ......................................................................................................... ........................................................................................................................................ ......................................................................................................... ............................................................................................................. ........................................................................................................ ......... ......................................................................................................................................... ..................................................................................................................... ............................................................................................... ........................................... ............................................................................................................................................. ................................................................................................ ...................................... .......................................................................................................................................... ....................................................................................................................................... ......................................................................................................................................... ................................... ...................................................................................................... ............................................................................................................................ ..................................................................................... .................................................... .......................................................................................................................................... ................................................................................................................................. ............................................................................... .................................................................................. ................................................................................................................ ............................................................................................................... ................................................................................................................... ........................................................................................................... .............................................................................................................................. 1 TABLE OF CONTENTS Documentation for This Machine.......................................................................................................................1 Manuals for This Machine.................................................................................................................................8 Manuals List......................................................................................................................................................10 What You Can Do with This Machine............................................................................................................11 Using This Machine as a Copier............................................................…

Text truncated - open the document above for the full version.

Loading Paper into the Small Size Paper Tray This section describes how to load paper into the small size paper tray. • Check the paper edges are aligned at the right side. 1. Carefully pull out the paper tray until it stops. CAS118 2. Square the paper and load it print side up. Do not stack paper over the limit mark. CAS119 3. Carefully push the paper tray fully in. • When loading a low number of sheets, be sure not to squeeze the side fences in too tightly. If the paper bows, it might not feed in properly. • If a paper tray is pushed vigorously when putting it back into place, the position of the tray's side fences may slip out of place. • Various sizes of paper can be loaded in the small size paper tray by adjusting the positions of side fences and end fence. For details, see “Changing the Paper Size in the Small Size Paper Tray”. Loading Paper 93 3 • You can load envelopes in the small size paper tray. For details about how to load envelopes, see “Changing the Paper Size in the Small Size Paper Tray”. For details about various details about and recommendations concerning envelopes, see “Envelopes”. • The small size paper tray can hold up to 550 sheets. • For details about how to install the small size paper tray, see “Installing the Small Size Paper Tray”. • p.87 "Installing the Small Size Paper Tray" • p.102 "Changing the Paper Size in the Small Size Paper Tray" • p.117 "Envelopes" Loading Paper into Tray 3 (LCT) This section describes how to load paper into Tray 3 (LCT). • When paper loaded in the right side of Tray 3 (LCT) runs out, paper on the left is automatically shifted to the right. While the paper is moving, a message instructing you to wait appears. Do not pull out the tray at this time. • For the right stack, align the right edge of the paper with the right edge of the tray. For the left stack, align the left edge of the paper to the left edge of the tray. • Tray 3 (LCT) can hold 8 1 / 2 × 11 paper only. If you want to print on A4 from Tray 3 (LCT), contact your service representative. 1. Carefully pull out Tray 3 (LCT) until it stops. CAS043 2. Square the paper and load it print side up. Do not stack paper over the limit mark. • Whole tray pulled out 3. Adding Paper 94 3 CAS044 • Left half of the tray pulled out CAS045 3. Carefully push the paper tray fully in. • You can load paper even while making copies from Tray 3 (LCT). You can pull out the left half of the tray while copying is in. • Load the same size and orientation paper in the other half of the tray. • Each tray can hold up to 1,000 sheets of paper. Loading Paper into the Large Capacity Tray (LCT) This section describes how to load paper into the large capacity tray (LCT). • The large capacity tray (LCT) can hold 8 1 / 2 × 11 paper only. If you want to print on A4 or B5 JIS from the large capacity tray (LCT), contact your service representative. • Check the paper edges are aligned at the left side. Loading Paper 95 3 1. Open the right cover of the large capacity tray (LCT). CAS089 2. Load the paper in the tray along the edge on the back. Load the paper print side down. CAS090 3. Press the [Down] key. The bottom plate is moving down. CAS091 4. Load paper by repeating steps 2 and 3. 5. Close the right cover of the large capacity tray (LCT). • The tray can hold up to 1,200 sheets. 3. Adding Paper 96 3 Loading Orientation-Fixed Paper or Two-Sided Paper This section describes loading paper that has a specified orientation and printing side (such as letterhead paper). Orientation-fixed (top to bottom) or two-sided paper (for example, letterhead paper, punched paper, or copied paper) might not print correctly, depending on how the originals and paper are placed. Set [Letterhead Setting] to [Yes] in [Input / Output] under [Copier / Document Server Features], and then place the original and paper as shown below. For details about Letterhead Setting, see “Copier and Document Server Features”, Copy and Document Server Reference. For details about printing with the printer function, see “Printing on Orientation-Fixed or Two-Sided Paper”, Printer Reference. Original Orientation Exposure glassADF • Copy • Scanner Loading Paper 97 3 Paper Orientation CAS049 3. Adding Paper 98 3 Changing the Paper Size This section describes how to change the paper size. • When loading paper, take care not to trap or injure your fingers. • Do not stack paper over the limit mark. • Tray 1, Tray 3 (LCT), and the large capacity tray (LCT) can hold 8 1 / 2 × 11 paper only. If you want to print on any of the following paper sizes from these trays, contact your service representative: • Tray 1: A4, A5, B5 JIS • Tray 3 (LCT): A4 • Large capacity tray (LCT): A4, B5 JIS • Be sure to select the paper size with User Tools. If you do not, misfeeds might occur. For details about Tray Paper Size, see “System Settings”, Network and System Settings Reference . • Fan the paper before loading. • Straighten curled or warped paper before loading. • For details about paper sizes and types, see “Recommended Paper Sizes and Types”. • p.111 "Recommended Paper Sizes and Types" Changing the Paper Size in Trays 2 - 4 This section describes how to change the paper size in trays 2 4. The paper size setting is changed in the same way for every paper tray. In the following example procedure, the paper size setting for tray 2 is changed. • If a paper tray is pushed vigorously when putting it back into place, the position of the tray's side fences may slip out of place. • Check the paper edges are aligned at the right side. • Slide the side fences until they are aligned with the paper size, and then re-lock the side fences. Various sizes of paper can be loaded in trays 2 4 by adjusting the positions of the side fences and end fence. Changing the Paper Size 99 3 1. Check that paper in the paper tray is not being used, and then pull the tray carefully out until it stops. CAS051 2. Remove paper if loaded. 3. Release the lock on the side fences. CAS052 4. While pressing down the …

Text truncated - open the document above for the full version.

External Photo Color Copier Front Rear Right Left Ricoh Company, Ltd. FCC ID:BBP-RFAPL03 IC:144D-RFAPL03 External Photo Color Copier Top Ricoh Company, Ltd. FCC ID:BBP-RFAPL03 IC:144D-RFAPL03

Rating Label FCC ID/IC Number Label

䌁䌰䌯䌬䌬䌯䌮䋯䌁䌴䌨䌥䌮䌡䋭䌃䋲䋮䋵 㪉㪇㪈㪇㪆㪇㪌㪆㪉㪇 㪘㪝㪡㪈㪏 ૒⮮㩿ᥓ㪀 㪛㪇㪏㪍㪏㪏㪉㪏 㪛㪇㪏㪍㪄㪈㪎 C9130/LD630C/Aficio MP C3001 ╙㪊㪚㩷ㇱᛛቶ 䌁䌰䌯䌬䌬䌯䌮䋯䌁䌴䌨䌥䌮䌡䋭䌃䋲䋮䋵 㪉㪇㪈㪇㪆㪇㪌㪆㪉㪇 㪘㪝㪡㪈㪏 ૒⮮㩿ᥓ㪀 㪛㪇㪏㪍㪏㪏㪊㪐 㪛㪇㪏㪍㪄㪌㪈 C9130G/LD630CG/Aficio MP C3001G ╙㪊㪚㩷ㇱᛛቶ  ࡞࠺ࡕฬߩᄌᦝޕ˴˴˴˴˴˴˴˴˴˴˴˴˴૒⮮㧔ᥓ㧕 䌁䌰䌯䌬䌬䌯䌮䋯䌁䌴䌨䌥䌮䌡䋭䌃䋲䋮䋵 㪉㪇㪈㪇㪆㪇㪌㪆㪉㪈 㪘㪝㪡㪈㪏 ૒⮮㩿ᥓ㪀 㪛㪇㪏㪎㪏㪏㪊㪊 㪛㪇㪏㪎㪄㪈㪎 C9135/LD635C/Aficio MP C3501 ╙㪊㪚㩷ㇱᛛቶ 䌁䌰䌯䌬䌬䌯䌮䋯䌁䌴䌨䌥䌮䌡䋭䌃䋲䋮䋵 㪉㪇㪈㪇㪆㪇㪌㪆㪉㪈 㪘㪝㪡㪈㪏 ૒⮮㩿ᥓ㪀 㪛㪇㪏㪎㪏㪏㪊㪐 㪛㪇㪏㪎㪄㪌㪈 C9135G/LD635CG/Aficio MP C3501G ╙㪊㪚㩷ㇱᛛቶ  ࡞࠺ࡕฬߩᄌᦝޕ˴˴˴˴˴˴˴˴˴˴˴˴˴૒⮮㧔ᥓ㧕 䌁䌰䌯䌬䌬䌯䌮䋯䌁䌴䌨䌥䌮䌡䋭䌃䋲䋮䋵 㪉㪇㪈㪇㪆㪇㪌㪆㪉㪈 㪘㪝㪡㪈㪏 ૒⮮㩿ᥓ㪀 㪛㪇㪏㪏㪏㪏㪊㪊 㪛㪇㪏㪏㪄㪈㪎 C9145/LD645C/Aficio MP C4501 ╙㪊㪚㩷ㇱᛛቶ 䌁䌰䌯䌬䌬䌯䌮䋯䌁䌴䌨䌥䌮䌡䋭䌃䋲䋮䋵 㪉㪇㪈㪇㪆㪇㪌㪆㪉㪈 㪘㪝㪡㪈㪏 ૒⮮㩿ᥓ㪀 㪛㪇㪏㪏㪏㪏㪊㪐 㪛㪇㪏㪏㪄㪌㪈 C9145G/LD645CG/Aficio MP C4501G ╙㪊㪚㩷ㇱᛛቶ  ࡞࠺ࡕฬߩᄌᦝޕ˴˴˴˴˴˴˴˴˴˴˴˴˴૒⮮㧔ᥓ㧕 䌁䌰䌯䌬䌬䌯䌮䋯䌁䌴䌨䌥䌮䌡䋭䌃䋲䋮䋵 㪉㪇㪈㪇㪆㪇㪌㪆㪉㪇 㪘㪝㪡㪈㪏 ૒⮮㩿ᥓ㪀 㪛㪇㪏㪐㪏㪏㪊㪊 㪛㪇㪏㪐㪄㪈㪎 C9155/LD655C/Aficio MP C5501 ╙㪊㪚㩷ㇱᛛቶ 䌁䌰䌯䌬䌬䌯䌮䋯䌁䌴䌨䌥䌮䌡䋭䌃䋲䋮䋵 㪉㪇㪈㪇㪆㪇㪌㪆㪉㪇 㪘㪝㪡㪈㪏 ૒⮮㩿ᥓ㪀 㪛㪇㪏㪐㪏㪏㪊㪐 㪛㪇㪏㪐㪄㪌㪈 C9155G/LD655CG/Aficio MP C5501G ╙㪊㪚㩷ㇱᛛቶ  ࡞࠺ࡕฬߩᄌᦝޕ˴˴˴˴˴˴˴˴˴˴˴˴˴૒⮮㧔ᥓ㧕

External Photo Ricoh Company, Ltd. Color Laser Printer FCC ID: BBP-RFAPL03 IC: 144D-RFAPL03 RFID Part Location -1 RFID Part Location -2 External Photo Ricoh Company, Ltd. Color Laser Printer FCC ID: BBP-RFAPL03 IC: 144D-RFAPL03 RFID Part Location -3 External Photo Ricoh Company, Ltd. Color Laser Printer FCC ID: BBP-RFAPL03 IC: 144D-RFAPL03 Top Bottom External Photo Ricoh Company, Ltd. Color Laser Printer FCC ID: BBP-RFAPL03 IC: 144D-RFAPL03 Top close-up - 1 Top close-up - 2 External Photo Ricoh Company, Ltd. Color Laser Printer FCC ID: BBP-RFAPL03 IC: 144D-RFAPL03 Top close-up - 3 Bottom close-up - 1 Print Pattern Antenna External Photo Ricoh Company, Ltd. Color Laser Printer FCC ID: BBP-RFAPL03 IC: 144D-RFAPL03 Bottom close-up - 2 Bottom close-up - 3

FCC ID : BBP-RFAPL03 Test report No. : 30IE0112-SH-01-A Page : 1 of 25 Issued date : July 15, 2010 Revised date : August 20, 2010 UL Japan, Inc. SHONAN EMC LAB. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401 RADIO TEST REPORT Test Report No. : 30IE0112-SH-01-A Applicant : RICOH COMPANY LTD. Type of Equipment : Color Copier Model No. : Aficio MP C5501 FCC ID : BBP-RFAPL03 Test regulation : FCC Part15 Subpart C: 2010 Test result : Complied 1. This test report shall not be reproduced in full or partial, without the written approval of UL Japan, Inc. 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the limits of the above regulation. 4. The test results in this test report are traceable to the national or international standards. 5. This test report must not be used by the customer to claim product certification, approval, or endorsement by any agency of the Federal Government. 6. The opinions and the interpretations to the result of the description in this report are outside scopes where UL Japan has been accredited. Date of test: June 21, 29 and 30, 2010 Tested by: Hikaru Shirasawa Tatsuya Arai Engineer of EMC Services Engineer of EMC Services Makoto Hosaka Engineer of EMC Services Approved by: Go Ishiwata Assistant Manager of EMC Service The testing in which "Non-accreditation" is displayed is outside the accreditation scopes in UL Japan. There is no testing item of "Non-accreditation". RTL02610 MF060d (06.08.09) FCC ID : BBP-RFAPL03 Test report No. : 30IE0112-SH-01-A Page : 2 of 25 Issued date : July 15, 2010 UL Japan, Inc. SHONAN EMC LAB. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401 Table of Contents Page 1 Applicant information 3 2 Equipment under test (E.U.T.) 3 3 Test specification, procedures and results 4 4 System test configuration 6 5 Conducted emission 8 6 Radiated emissions (Fundamental, Spurious and Outside the Allocated bands) 9 7 20dB bandwidth & Occupied bandwidth (99%) 11 8 Frequency tolerance 11 Contents of Appendixes 12 FCC ID : BBP-RFAPL03 Test report No. : 30IE0112-SH-01-A Page : 3 of 25 Issued date : July 15, 2010 UL Japan, Inc. SHONAN EMC LAB. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401 1 Applicant information Company Name : RICOH COMPANY LTD. Address : 810 Shimoimaizumi, Ebina-shi, Kanagawa-ken 243-0460, Japan Telephone Number : +81-46-292-9152 Facsimile Number : +81-46-292-9183 Contact Person : Akihiro Kurosaka 2 Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of Equipment : Color Copier Model No. : Aficio MP C5501 Serial No. : V9610100004 Rating : AC120 - 127V, 12A Country of Mass-production : China Receipt Date of Sample : June 21, 2010 Condition of EUT : Engineering prototype (Not for Sale: This sample is equivalent to mass-produced items.) Modification of EUT : No Modification by the test lab 2.2 Product description Model No: Aficio MP C5501 , referred to as the EUT in this report, is the Color Copier. Refer to the Appendix for the difference between the EUT and its similar models. Radio Specification Radio Type : Transceiver Frequency of Operation : 13.56MHz Clock frequency : 13.56MHz Modulation : ASK 100% Power Supply (inner) : DC 5.0V Antenna type : Print pattern…

Text truncated - open the document above for the full version.