BBP-WLRWL542Option(s) for Radiocommunications

• Confirm that the Gigabit Ethernet board was correctly installed by printing the configuration page. If it is correctly installed, "Gigabit Ethernet & USB 2.0" will appear for "Device Connection" on the configuration page. • If the board was not installed properly, repeat the procedure from step 2. If it cannot be installed correctly even after reattempting installation, contact your sales or service representative. • For details about printing the configuration page, see "Test Printing", Quick Installation Guide. • Before using the Gigabit Ethernet board, you must configure settings from the printer control panel. For details, see "Ethernet Configuration". • p.59 "Ethernet Configuration" Installing the Wireless LAN Interface Board • Do not touch inside the controller board compartment. Doing so may cause a machine malfunction or a burn. • Before beginning work, ground yourself by touching something metal to discharge any static electricity. Static electricity can damage the unit. • Do not subject the unit to physical shocks. 1. Check the contents of the package. BFL301S 2. Turn off the power, and then unplug the power cable. 2. Installing Options 42 2 3. Loosen the two screws and remove the cover of the Wireless LAN interface board installation unit. BFL055S The removed cover is not used when installing the interface board. 4. Fully insert the Wireless LAN interface board. BFL058S 5. Tighten the two screws to secure the interface board. Check the Wireless LAN interface board is connected firmly to the controller board. • Confirm that the interface board was correctly installed by printing the configuration page. If it is correctly installed, "Wireless LAN" will appear for "Device Connection" on the configuration page. • If the board was not installed properly, repeat the procedure from step 2. If it cannot be installed correctly even after reattempting installation, contact your sales or service representative. • For details about printing the configuration page, see "Test Printing", Quick Installation Guide. • Before using the Wireless LAN interface board, you must configure settings from the printer control panel. For details, see "Wireless LAN Configuration". • p.70 "Wireless LAN Configuration" Installing the Interface Units 43 2

Note to users for R-WL54M1N/R-WL54C1N/R-WL54M1GN/R-WL54C1GN It is strictly forbidden to use antenna except designated. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated with at least 20cm more between the radiator and person's body(excluding extremities:hands, wrists, feet and ankles). Note to users for R-WL54M1N/R-WL54C1N The model R-WL54M1N/R-WL54C1N for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel Mobile Satellite systems. Note to users in Canada This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices. Remarque concermant les utilisateurs au Canada Ce dispositif est conforme à la norme CNR-Gen d’Industrie Canada. L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1)il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Les utilisateurs de radars de haute puissance ont une allocation primaire(c.-à-d.qu’ils ont la priorité) pour les bandes 5 250 – 5 350 MHz et 5 650 – 5 850 MHz et que ces radars pourraient causer du brouillage et/ou du dommage aux dispositifs pour réseaux locaux. Note to users in the United States of America Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communica- tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Declaration of Conformity Product Name: Wireless LAN board Model Number: R-WL54CN Responsible party: Ricoh Americas Corporation Address: 5 Dedrick Place, West Caldwell, NJ 07006 Telephone number: 973-882-2000 This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note to users in Canada Note: This Class B digital apparatus complies with Canadian ICES-003. Remarque concernant les utilisateurs au Canada Avertissement: Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Copyright 2007, 2009 Printed in Japan EN US D475-7301 5:/&1 2SWLRQ V IRU5DGLRFRPPXQLFDWLRQV

Note to users for R-WL54M1N/R-WL54C1N/R-WL54M1GN/R-WL54C1GN It is strictly forbidden to use antenna except designated. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated with at least 20cm more between the radiator and person's body(excluding extremities:hands, wrists, feet and ankles). Note to users for R-WL54M1N/R-WL54C1N The model R-WL54M1N/R-WL54C1N for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel Mobile Satellite systems. Note to users in Canada This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices. Remarque concermant les utilisateurs au Canada Ce dispositif est conforme à la norme CNR-Gen d’Industrie Canada. L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1)il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Les utilisateurs de radars de haute puissance ont une allocation primaire(c.-à-d.qu’ils ont la priorité) pour les bandes 5 250 – 5 350 MHz et 5 650 – 5 850 MHz et que ces radars pourraient causer du brouillage et/ou du dommage aux dispositifs pour réseaux locaux. Note to users in the United States of America Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communica- tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Caution: For compliance with FCC limitations on emission, make sure the wireless LAN antenna is correctly installed and the ferrite core securely attached. Declaration of Conformity Product Name: Wireless LAN board Model Number: R-WL54MN Responsible party: Ricoh Americas Corporation Address: 5 Dedrick Place, West Caldwell, NJ 07006 Telephone number: 973-882-2000 This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note to users in Canada Note: This Class B digital apparatus complies with Canadian ICES-003. Remarque concernant les utilisateurs au Canada Avertissement: Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Copyright©2009 Printed in Japan EN US D475-7201 5:/01 2SWLRQ V IRU5DGLRFRPPXQLFDWLRQV

Internal Photo Ricoh Company, Ltd. FCC ID: BBP-WLRWL542 IC : 144D-WLRWL542 (Model: R-WL54C1N) Top (with shield) Top (without shield) Internal Photo Ricoh Company, Ltd. FCC ID: BBP-WLRWL542 IC : 144D-WLRWL542 (Model: R-WL54C1N) Top Bottom

Internal Photo Ricoh Company, Ltd. FCC ID: BBP-WLRWL542 IC: 144D-WLRWL542 (Model: R-WL54M1N) Top (with shield) Top (without shield) Internal Photo Ricoh Company, Ltd. FCC ID: BBP-WLRWL542 IC: 144D-WLRWL542 (Model: R-WL54M1N) Top Bottom Internal Photo Ricoh Company, Ltd. FCC ID: BBP-WLRWL542 IC: 144D-WLRWL542 (Model: R-WL54M1N) Antenna (Internal)

Internal Photo Ricoh Company, Ltd. FCC ID: BBP-WLRWL542 IC : 144D-WLRWL542 (Model: R-WL54C1N) Top (with shield) Top (without shield) Internal Photo Ricoh Company, Ltd. FCC ID: BBP-WLRWL542 IC : 144D-WLRWL542 (Model: R-WL54C1N) Top Bottom

Internal Photo Ricoh Company, Ltd. FCC ID: BBP-WLRWL542 IC: 144D-WLRWL542 (Model: R-WL54M1N) Top (with shield) Top (without shield) Internal Photo Ricoh Company, Ltd. FCC ID: BBP-WLRWL542 IC: 144D-WLRWL542 (Model: R-WL54M1N) Top Bottom Internal Photo Ricoh Company, Ltd. FCC ID: BBP-WLRWL542 IC: 144D-WLRWL542 (Model: R-WL54M1N) Antenna (Internal)

UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401 Applicant: RICOH COMPANY, LTD. Type of Equipment : O ption(s) for Radiocommunications Model No. : R-W L54C1N FCC ID: BBP-WLRWL542 RICOH COM PANY, LTD. declares that M odel : Option(s) for Radiocommunications complies with FCC radiation exposure requirement specified in the FCC Rules 2.1091. The “R-W L54C1N“ has 16.44 mW of conducted Peak Output power and 41.3 mW of EIRP. This equipment is considered as a mobile device so that SAR testing is excluded. The Following calculation is the reference data for 20cm distance. R F E xposure C alculations: The following information provides the minimum separation distance for the highest gain antenna provided with the “R-W L54C1N“ as calculated from FCC O ET Bulletin 65 Appendix A, Table (B) Limits for G eneral Population / Uncontrolled Exposure. This calculation is based on the highest EIRP possible from the system, considering maximum power and antenna gain, and considering a 1.0mW /cm^2 uncontrolled exposure limit. The Friis formula used was: S = (P * G) / (4* π * r 2 ) W here P = 16.44 mW (Maximum peak output power) G = 2.51 Numerical Antenna gain; equal to 4.00 dBi r =20.0 cm For: R-W L54C1NS = 0.00822 mW/cm 2 No. : 30GE0098-YK-B-R1 RF Exposure / SAR Statement

UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401 Applicant: RICOH COMPANY, LTD. Type of Equipment : O ption(s) for Radiocommunications Model No. : R-W L54M1N FCC ID: BBP-WLRWL542 RICOH COM PANY, LTD. declares that M odel : Option(s) for Radiocommunications complies with FCC radiation exposure requirement specified in the FCC Rules 2.1091. The “R-W L54M 1N“ has 14.35 mW of conducted Peak Output power and 36.06 mW of EIRP. This equipment is considered as a mobile device so that SAR testing is excluded. The Following calculation is the reference data for 20cm distance. R F E xposure C alculations: The following information provides the minimum separation distance for the highest gain antenna provided with the “R-W L54M 1N“ as calculated from FCC O ET Bulletin 65 Appendix A, Table (B) Limits for G eneral Population / Uncontrolled Exposure. This calculation is based on the highest EIRP possible from the system, considering maximum power and antenna gain, and considering a 1.0mW /cm^2 uncontrolled exposure limit. The Friis formula used was: S = (P * G) / (4* π * r 2 ) W here P = 14.35 mW (Maximum peak output power) G = 2.51 Numerical Antenna gain; equal to 4.00 dBi r =20.0 cm For: R-W L54M1NS = 0.00717 mW/cm 2 No. : 30GE0098-YK-D-R1 RF Exposure / SAR Statement

FCC ID : BBP-WLRWL542 Test report No. : 30GE0098-YK-B-R1 Page : 1 of 58 Issued date : April 2, 2010 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401 RADIO TEST REPORT Test Report No.: 30GE0098-YK-B-R1 Applicant : RICOH COMPANY LTD. Type of Equipment : Option(s) for Radiocommunications Model No. : R-WL54C1N FCC ID : BBP-WLRWL542 Test regulation : FCC Part15 Subpart E: 2010 Test result : Complied 1. This test report shall not be reproduced in full or partial, without the written approval of UL Japan, Inc. 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the limits of the above regulation. 4. The test results in this test report are traceable to the national or international standards. 5. This test report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. 6. This report is a revised version of 30GE0098-YK-B. 30GE0098-YK-B is replaced with this report. Date of test: February 18, 22, 24 and March 1-3, 2010 Tested by: Tatsuya Arai Makoto Hosaka Engineer of EMC Service Engineer of EMC Service Akio Hayashi Engineer of EMC Service Approved by: Ichiro Isozaki Leader of EMC Service MF060b (06.08.09) FCC ID : BBP-WLRWL542 Test report No. : 30GE0098-YK-B-R1 Page : 2 of 58 Issued date : April 2, 2010 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401 Table of Contents Page 1 Applicant information 3 2 Equipment under test (E.U.T.) 3 3 Test specification, procedures and results 4 4 System test configuration 7 5 Conducted Emission 9 6 26dB Bandwidth & Occupied Bandwidth (99%) 10 7 Maximum Peak Output Power 10 8 Peak Power Spectral Density 10 9 Peak Excursion Ratio 10 10 Out of Band Emissions (Antenna Port Conducted) 10 11 Out of band emissions (Radiated) 11 Contents of Appendixes 12 APPENDIX 1: Photographs of test setup 13 APPENDIX 2: Test data 16 APPENDIX 3: Test instruments 58 FCC ID : BBP-WLRWL542 Test report No. : 30GE0098-YK-B-R1 Page : 3 of 58 Issued date : April 2, 2010 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401 1 Applicant information Company Name : RICOH COMPANY, LTD. Address : 1-3-6 Nakamagome, Ohta-ku, Tokyo, 143-8555 Japan Telephone Number : +81-3-6890-3804 Facsimile Number : +81-3-5742-5489 Contact Person : Kazuki Kitazawa 2 Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of Equipment : Option(s) for Radiocommunications Model No. : R-WL54C1N Serial No. : 911S0334 Rating : DC3.3V Country of Mass-production : Japan Receipt Date of Sample : Production prototype (Not for Sale: This sample is equivalent to mass-produced items.) Condition of EUT : No modification by the test lab. Modification of EUT : February 17, 2010 2.2 Product description Model: R-WL54C1N (referred to as the EUT in this report) is a Option(s) for Radiocommunications. Equipment type : Transceiver Frequency of operation : [11b/g] 2412-2462MHz *1) [11a] 5180-5320MHz Clock frequency : 11MHz, 20MHz Bandwidth & channel spacing : [11b/g] 22MHz & 5MHz [11a] 18MHz & 20MHz Type of modulation : IEEE802.11a: OFDM (BPSK, QPSK, 16QAM, 64QAM) IEEE802.11b: DSSS (DBPSK, DQPSK, CCK) IEEE802.11g: OFDM (BPSK, QPSK, 16QAM, 64QAM) Antenna type : Chip Antenna 1: Transmitting & Receiving Antenna 2: Receiving only Antenna connector type : None Antenna gain : [11b/g] max +1dBi [11a] max +4dBi ITU code : D1D, G1D Operation temperature range : 0 ~ +65 deg.C. *1) Refer to 30GE0098-YK-A-R1, FCC part 15C (FCC 15.247) report. FCC 15.31 (e) The RF Module has its own regulator. The RF Module is constantly provided voltage (DC3.3V, 2.9V, 2.8V, and 1.2V) through its own regulator regardless of input voltage. Therefore, this EUT complies with the requirement. FCC Part15.203 Antenna requirement The antenna is not removable from the EUT. Therefore, the equipment complies with the antenna requirement of Section 15.203. FCC ID : BBP-WLRWL542 Test report No. : 30GE0098-YK-B-R1 Page : 4 of 58 Issued date : April 2, 2010 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401 3 Test specification, procedures and results 3.1 Test specification Test specification : FCC Part 15 Subpart E: 2010, final revised on January 22, 2010 and effective March 1, 2010 Title : FCC 47CFR Part15 Radio Frequency Device : Subpart E Unlicensed National Information Infrastructure Devices : Section 15.407 General technical requirements *The revision on January 22, 2010 does not affect the test specification applied to the EUT. The EUT complies with FCC Part 15 Subpart B: 2010, final revised on January 22, 2010 and effective March 1, 2010 3.2 Procedures & Results Item Test Procedure Specification Remarks DeviationWorst Margin Results Conducted Emission ANSI C63.4:2003 7. AC powerline conducted emission measurements 15.407 (b)(6) and 15.207 - N/A 4.0dB (20.97470MHz, AV, 11a Tx 5280MHz) Complied 26dB Emission Bandwidth ANSI C63.4:2003 13. Measurement of intentional radiators FCC 15.407(a)(1)(2) Conducted N/A Complied Maximum Peak Output Power ANSI C63.4:2003 13. Measurement of intentional radiators FCC 15.407 (a)(1)(2) Conducted N/A Complied Peak Power Spectral Density ANSI C63.4:2003 13. Measurement of intentional radiators FCC 15.407 (a)(1)(2) Conducted N/A Complied Peak Excursion Ratio ANSI C63.4:2003 13. Measurement of intentional radiators FCC 15.407 (a)(6) Conducted N/A Complied Out of Band Emission & Restricted Band Edges ANSI C63.4:2003 13. Measurement of intentional radiators 15.407 (b)(1)(2)(4)(6) (7), 15.205 and 15.209 Conducted N/A See data Complied Out of Band Emission & Restricted Band Edges ANSI C63.4:2003 13. Measurement of …

Text truncated - open the document above for the full version.

Test Report No.: 30GE0098-YK-B-R1 Page :22/ 58 Issued date : April 2, 2010 FCC ID : BBP-WLRWL542 Test placeUL Japan, Inc. Shonan EMC Lab. No.5 Shielded Room Date 2010/3/2 Temperature / Humidity26deg.C., 32% EngineerAkio Hayashi Mode11a, Tx, Antenna A Frequency26dB Bandwidth99% Occupied [MHz][MHz]Bandwidth [MHz] 518018.80916.855 520018.26516.899 524018.80916.867 526017.94816.855 528017.92716.943 532017.73416.929 26dB Bandwidth and 99% Occupied Bandwidth UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 Test Report No.: 30GE0098-YK-B-R1 Page :23/ 58 Issued date : April 2, 2010 FCC ID :BBP-WLRWL542 26dB Bandwidth Tx, 5180MHzTx, 5200MHz Tx, 5280MHzTx, 5320MHz Tx, 5240MHzTx, 5260MHz 11a UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 Test Report No.: 30GE0098-YK-B-R1 Page :24/ 58 Issued date : April 2, 2010 FCC ID :BBP-WLRWL542 99% Occupied Bandwidth Tx, 5180MHzTx, 5200MHz Tx, 5280MHzTx, 5320MHz Tx, 5240MHzTx, 5260MHz 11a UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 Test Report No.: 30GE0098-YK-B-R1 Page :25/ 58 Issued date : April 2, 2010 FCC ID : BBP-WLRWL542 Test placeUL Japan, Inc. Shonan EMC Lab. No.3 Shielded Room Date2010/2/18 Temperature / Humidity22deg.C., 36% EngineerAkio Hayashi ModeIEEE802.11a / Transmitting, 54Mbps ChFreq.S/ACableAtten.Margin ReadingLossLoss [MHz][dBm][dB][dB][dBm][mW][dBm][mW][dB] Lower band, Low5180.0-0.461.8510.0611.4513.9616.7447.255.29 Lower band, Mid5200.0-0.061.8510.0611.8515.3116.6245.884.77 Lower band, High5240.00.241.8510.0712.1616.4416.7447.254.58 Mid band, Low5260.0-0.011.8410.0811.9115.5223.54225.9511.63 Mid band, Mid5280.0-0.251.8410.0811.6714.6923.54225.6911.87 Mid band, High5320.0-0.641.8410.0911.2913.4623.49223.2612.20 Sample Calculation: Result = Reading + Cable Loss + Cable Loss (supplied by customer) + Atten. Loss 15.407(a)(1) Limit(Cond.) = 16.99dBm(50mW) or 4 + 10log(26dB BW) dBm 15.407(a)(2) Limit(Cond.) = 23.98dBm(250mW) or 11 + 10log(26dB BW) dBm * In the above table, factor 0.0dB represents no use of Atten. and/or Filter. *The test result is rounded off to one or two decimal places, so some differences might be observed. [Pre check] Data RateFreq.S/ACableAtten.Margin ReadingLossLoss [Mbps][MHz][dBm][dB][dB][dBm][mW][dBm][mW][dB] 65180.0-0.501.8510.0611.4113.8416.7447.255.33 95180.0-0.521.8510.0611.3913.7716.7447.255.35 125180.0-0.571.8510.0611.3413.6116.7447.255.40 185180.0-0.501.8510.0611.4113.8416.7447.255.33 245180.0-0.491.8510.0611.4213.8716.7447.255.32 365180.0-0.491.8510.0611.4213.8716.7447.255.32 485180.0-0.501.8510.0611.4113.8416.7447.255.33 545180.0-0.461.8510.0611.4513.9616.7447.255.29 Peak Output Power (Conducted) ResultLimit ResultLimit UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 Test Report No.: 30GE0098-YK-B-R1 Page :26/ 58 Issued date : April 2, 2010 FCC ID :BBP-WLRWL542 Peak Output Power (Conducted) Tx, 5180MHzTx, 5200MHz Tx, 5280MHzTx, 5320MHz Tx, 5240MHzTx, 5260MHz 11a UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 Test Report No.: 30GE0098-YK-B-R1 Page :27/ 58 Issued date : April 2, 2010 FCC ID :BBP-WLRWL542 11a, Reference chart Tx 5180MHz Peak Output Power (Conducted) 6Mbps9Mbps 24Mbps36Mbps 12Mbps18Mbps UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 Test Report No.: 30GE0098-YK-B-R1 Page :28/ 58 Issued date : April 2, 2010 FCC ID :BBP-WLRWL542 Peak Output Power (Conducted) 48Mbps54Mbps 11a, Reference chart Tx 5180MHz UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 Test Report No.: 30GE0098-YK-B-R1 Pa ge :29/ 58 Issued date : April 2, 2010 FCC ID : BBP-WLRWL542 Test placeUL Japan, Inc. Shonan EMC Lab. No.3 Semi Anechoic Chamber Date2010/2/222010/2/222010/2/24 Temperature / Humidity 20deg.C., 35%23deg.C., 35%22deg.C., 34% EngineerAkio HayashiAkio HayashiMakoto Hosaka ModeIEEE802.11a / Tx, 54Mbps, 5180MHz PolarityFrequencyDetector ReadingAnt.Fac.LossGainResultLimitMarginHeightAngle Remark [MHz][dBuV][dB/m][dB][dB][dBuV/m] [dBuV/m][dB][cm][deg.] Hori.155.854QP46.114.87.532.036.443.57.1200294X-axis Hori.239.96QP47.317.18.031.940.546.05.5150251X-axis Hori.319.938QP50.214.18.431.940.846.05.2100257X-axis Hori.599.977QP38.619.09.431.935.146.010.9150164X-axis Vert.239.96QP38.417.18.031.931.646.014.4100268Y-axis Vert.319.938QP43.114.18.431.933.746.012.3100285Y-axis Vert.599.977QP38.019.09.431.934.546.011.5100158Y-axis Hori.4144.001PK57.629.24.740.251.374.022.711130Z-axis Hori.5150PK65.231.55.439.262.974.011.110164Z-axis Hori.8287.987PK46.937.67.138.253.474.020.612459Z-axis Hori.15540PK45.539.60.237.547.874.026.2100306Y-axis Hori.20720PK54.240.1-2.743.847.874.026.2100298Y-axis Vert.4147.5PK56.529.24.740.250.274.023.8106346Z-axis Vert.5150PK65.231.55.439.262.974.011.1101252Z-axis Vert.8287.987PK44.837.67.138.251.374.022.7100343Z-axis Vert.15540PK45.639.60.237.547.974.026.1109175Y-axis Vert.20720PK51.140.1-2.743.844.574.029.5101177Y-axis Hori.4144.001AV55.229.24.740.248.954.05.111130Z-axis Hori.5150AV48.131.55.439.245.854.08.210164Z-axis Hori.8287.987AV38.137.67.138.244.654.09.412459Z-axis Hori.15540AV33.039.60.237.535.354.018.7100306Y-axis Hori.20720AV41.940.1-2.743.835.554.018.5100298Y-axis Vert.4147.5AV54.029.24.740.247.754.06.3106346Z-axis Vert.5150AV48.731.55.439.246.454.07.6101252Z-axis Vert.8287.987AV38.537.67.138.245.054.09.0100343Z-axis Vert.15540AV31.339.60.237.533.654.020.4109175Y-axis Vert.20720AV38.640.1-2.743.832.254.021.8101177Y-axis Re…

Text truncated - open the document above for the full version.

FCC ID : BBP-WLRWL542 Test report No. : 30GE0098-YK-D-R1 Page : 1 of 59 Issued date : April 2, 2010 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401 RADIO TEST REPORT Test Report No.: 30GE0098-YK-D-R1 Applicant : RICOH COMPANY LTD. Type of Equipment : Option(s) for Radiocommunications Model No. : R-WL54M1N FCC ID : BBP-WLRWL542 Test regulation : FCC Part15 Subpart E: 2010 Test result : Complied 1. This test report shall not be reproduced in full or partial, without the written approval of UL Japan, Inc. 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the limits of the above regulation. 4. The test results in this test report are traceable to the national or international standards. 5. This test report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. 6. This report is a revised version of 30GE0098-YK-D. 30GE0098-YK-D is replaced with this report. Date of test: February 18, 25-27 and March 1-3, 2010 Tested by: Tatsuya Arai Makoto Hosaka Engineer of EMC Service Engineer of EMC Service Akio Hayashi Engineer of EMC Service Approved by: Ichiro Isozaki Leader of EMC Service MF060b (06.08.09) FCC ID : BBP-WLRWL542 Test report No. : 30GE0098-YK-D-R1 Page : 2 of 59 Issued date : April 2, 2010 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401 Table of Contents Page 1 Applicant information 3 2 Equipment under test (E.U.T.) 3 3 Test specification, procedures and results 4 4 System test configuration 7 5 Conducted Emission 9 6 26dB Bandwidth & Occupied Bandwidth (99%) 10 7 Maximum Peak Output Power 10 8 Peak Power Spectral Density 10 9 Peak Excursion Ratio 10 10 Out of Band Emissions (Antenna Port Conducted) 10 11 Out of band emissions (Radiated) 11 Contents of Appendixes 12 APPENDIX 1: Photographs of test setup 13 APPENDIX 2: Test data 17 APPENDIX 3: Test instruments 59 FCC ID : BBP-WLRWL542 Test report No. : 30GE0098-YK-D-R1 Page : 3 of 59 Issued date : April 2, 2010 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401 1 Applicant information Company Name : RICOH COMPANY, LTD. Address : 1-3-6 Nakamagome, Ohta-ku, Tokyo, 143-8555 Japan Telephone Number : +81-3-6890-3804 Facsimile Number : +81-3-5742-5489 Contact Person : Kazuki Kitazawa 2 Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of Equipment : Option(s) for Radiocommunications Model No. : R-WL54M1N Serial No. : 91290017 Rating : DC3.3V Country of Mass-production : Japan Receipt Date of Sample : Production prototype (Not for Sale: This sample is equivalent to mass-produced items.) Condition of EUT : No modification by the test lab. Modification of EUT : February 17, 2010 2.2 Product description Model: R-WL54M1N (referred to as the EUT in this report) is a Option(s) for Radiocommunications. Equipment type : Transceiver Frequency of operation : [11b/g] 2412-2462MHz *1) [11a] 5180-5320MHz Clock frequency : 11MHz, 20MHz Bandwidth & channel spacing : [11b/g] 22MHz & 5MHz [11a] 18MHz & 20MHz Type of modulation : IEEE802.11a: OFDM (BPSK, QPSK, 16QAM, 64QAM) IEEE802.11b: DSSS (DBPSK, DQPSK, CCK) IEEE802.11g: OFDM (BPSK, QPSK, 16QAM, …

Text truncated - open the document above for the full version.