BEJMW60SZ12LCD Projection Monitor

P/NO : 3828VA0349A b (373-026H) MW-60SZ12 OWNER’S MANUAL LCD PROJECTION MONITORLCD PROJECTION MONITOR Please read this manual carefully before operatingyour set. Retain it for future reference.Record model number and serial number of the set. See the label attached on the back of the set andquote this information to your dealer when yourequire service.Model number : Serial number : LCD PROJECTION MONITOR LCD PROJECTION MONITOR FCC NOTICE • A Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. • Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Warning This is a class B product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures. Before operating the unit, please read this manual carefully. CONTENTS INTRODUCTION Safety Instructions..................................................................4 Names of parts.....................................................................12 COMPOSITION Turning on the Monitor..........................................................18 Turning off the Monitor..........................................................19 Selecting source mode.........................................................20 CONNECTION Connecting to a Desktop PC................................................21 Connecting to a Notebook PC..............................................22 Connecting to a Macintosh Desktop PC...............................23 Connecting to a Macintosh PowerBook...............................24 Connecting to a Video Source..............................................25 Connecting to a DVD............................................................26 Connecting to a D-TV Set-Top Box......................................27 Connecting to a MIC.............................................................28 BASIC FUNCTIONS Function checking.................................................................29 Using Still function................................................................30 SPECIALFUNCTIONS Selecting language...............................................................31 Checking lamp time..............................................................32 Positioning............................................................................33 Using Zoom function.............................................................34 Using ARC function..............................................................35 TRACKING Using Tracking function........................................................36 VIDEO Adjusting Video.....................................................................38 AUDIO Adjusting Audio.....................................................................40 Using Audio Input function....................................................41 Using DASPfunction............................................................42 Using AVLfunction................................................................43 RS-232C External control device setup...............................................44 INFORMATION Supported Monitor Display...................................................50 Specifications .......................................................................51 4 Safety Instructions GGAlways keep the safety instructions to prevent any potential accident or misuse of the monitor. GG After reading this manual, keep it in the place that the user always can contact easily. GGSafety Instructions have two kinds of information, and each meaning of it is as below. WARNING This instruction may cause serious or fatal injuries. NOTES This instruction may cause light personal injuries or damage to the monitor. Indoor Installation-WARNING Indoor Installation-NOTES Do not place the Monitor in direct sunlight or near heat sources such as radiators, fires and stove etc. - This may cause a fire hazard ! Disconnect from the mains and remove all connections before moving. Do not place the monitor close to sources of steam or oil such as a humidifier. - This may create a fire hazard or an electric shock hazard ! Do not place inflammable materials beside the monitor. - This may cause a fire hazard ! Do not allow children hang on or climb on the installed monitor. -This may cause the display to fall, causing a fatal injury. When unpacking or moving the Monitor two people will be necessary to lift it safely. Do not place the monitor where it might be exposed to dust. - This may cause a fire hazard ! When installing the monitor on a table, be careful not to place it near the edge. -This may cause the monitor to fall causing serious personal injury and serious damage to the monitor. -Be sure to use a suitable table or rack. Only use the monitor on a level and sta- ble surface. -Else it may become unstable and affect correct operation. Ensu…

Text truncated - open the document above for the full version.

VPC3230 uPD64083 SW Buffer FLI2200 ADV7123 (DRP-2) CXA2101 SW SW AD9884SWPW164 8255 SIL161B M62352 M62352 MSP3440LA4282 Mouse MICOM E7050 E1031E6070E1031E6070E1031E6070 R LCDG LCDB LCD ROM Flash memory SRAM 16M RAM Buffer DS232 CVBS S-VIDEO Y Pb/Cb Pr/Cr PC OUT PC1 PC2 DVI-I RS-232 R/L MIKE MOUSE

Page 3 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Letter of Modification Date: September 19, 2002 Subject : RFI related modifications incorporated into unit with FCC ID. : BEJMW60SZ12 Dear Sir, This letter services as our declaration that all modifications listed below are implemented in the sample submitted for pre-grant testing. We further declare that the same modifications will be implemented into all production unit to enhance compliance of the unit to FCC limits. The modifications include the following : 1. Added a ferrite core on the power cord with 3 turns. @ Refer to Page 10 (Figure 10, Point 1) 2. Added a ferrite core on the thermo sensor connect wire with 2 turns. @ Refer to Page 11 (Figure 11, Point 2) 3. Added a ferrite core on the fan connect wire with 2 turns. @ Refer to Page 11 (Figure 11, Point 3) 4. Added a ferrite core on the DC-PWR connect wire (form power board to main board) with 2 turns. @ Refer to Page 11 (Figure 11, Point 4) 5. Added ferrite cores on the L/R wires of speaker with 2 turns separately. @ Refer to Page 11 (Figure 12, Point 5 & 6) 6. Added a ferrite core on the connect wire of IR board with 2 turns. @ Refer to Page 13 (Figure 16, Point 7) 7. Added a ferrite core on the connect wire of control board with 2 turns. @ Refer to Page 19 (Figure 27, Point 8) 8. Added a ferrite core on the connect wire of ballast power with 2 turns. @ Refer to Page 19 (Figure 27, Point 9) 9. Added conductive gaskets on the top-case of main board. @ Refer to Page 20 (Figure 29, Point 10) 10. Added conductive gaskets on the pack holder of RGB/DVI-I interface board. @ Refer to Page 24 (Figure 37, Point 11) 11. Bonded two ferrite cores on the Analog D-Sub cable. @ Refer to Page 37 (Figure 64, Point 12) 12. Bonded two ferrite cores on the DVI-I cable. @ Refer to Page 37 (Figure 64, Point 13) If you have any questions or require any other information please do not hesitate to contact our agent. Sincerely Yours, W.H. OH, Team Leader Foreign Standards Research Lab. TV Pnant, LG Electronics Inc.

Page 6 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Photographs Figure 1 General Appearance (Front View) Figure 2 Appearance (Front Panel View) Page 7 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 3 General Appearance (Left-Side View) Figure 4 General Appearance (Right-Side View) Page 8 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 5 General Appearance (Rear View) Figure 6 Appearance (I/O Connectors)

MW-60SZ12 BEJMW60SZ12 120V 60Hz 2A 230 WATTS

Page 9 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 7 Internal View (Back, Removed Cover) Figure 8 Frame of Internal Page 10 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 9 Frame of Internal Figure 10 Internal View (EMI Core) 1 Page 11 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 11 Internal View (EMI Cores) Figure 12 Internal View (I/O Module & Control Board) 3 4 5 6 Page 12 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 13 Frame of Internal Figure 14 Frame of Internal Page 13 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 15 Internal View (Front Cover & Screen) Figure 16 Internal View (Control Board & EMI Core) 7 Page 14 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 17 Internal View (Speaker) Figure 18 Internal View (Speaker) Page 15 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 19 Remote Control Receiver Board (Component Side) Figure 20 Remote Control Receiver Board (Solder Side) Page 16 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 21 Key Connection Board (Component Side) Figure 22 Key Connection Board (Solder Side) Page 17 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 23 Internal View Figure 24 Internal View Page 18 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 25 Function Key Board (Component Side) Figure 26 Function Key Board (Solder Side) Page 19 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 27 Internal View (EMI Cores) Figure 28 Frame of Internal (Lens & Lamp Module) 8 9 Page 20 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 29 Frame of Internal (Lens & Lamp Module) Figure 30 Frame of Internal (Main Board with Holder) 10 Page 21 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 31 Internal View (I/O Control Board) Figure 32 Sub Server Board (Component Side) Page 22 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 33 Sub Server Board (Solder Side) Figure 34 I/O Control Board (Component Side) Page 23 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 35 A/V Control Board (Component Side) Figure 36 A/V Control Board (Solder Side) Page 24 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 37 RGB/DVI Connection Board with Holder Figure 38 RGB/DVI Connection Board 11 Page 25 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 39 RGB/DVI Connection Board Figure 40 RGB/DVI Connection Board Page 26 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 41 Main Board (Component Side) Figure 42 Main Board (Solder Side) Page 27 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 43 Internal View Figure 44 Frame of Internal Page 28 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 45 Lampdriver & Control Board (Component Side) Figure 46 Lampdriver Module Page 29 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 47 Lampdriver & Control Board (Component Side) Figure 48 Lampdriver & Control Board (Solder Side) Page 30 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 49 Sensor Board (Component Side) Figure 50 Sensor Board (Solder Side) Page 31 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 51 Line Filter Board (Component Side) Figure 52 Line Filter Board (Solder Side) Page 32 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 53 Power Supply Board (Component Side) Figure 54 Power Supply Board (Solder Side) Page 33 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 55 Internal View Figure 56 Internal View (Speaker) Page 34 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 57 SW Board (Solder Side) Figure 58 SW Board (Component Side) Page 35 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 59 Remote Control (Appearance, Front View) Figure 60 Remote Control (Appearance, Back View) Page 36 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 61 Remote Control (Removed Covers, Frame of Internal) Figure 62 Remote Control (PCB View, Front Side) Page 37 LG Electronics USALCD Projection MonitorFCC ID. : BEJMW60SZ12 Figure 63 Remote Control (PCB View, Back Side) Figure 64 RGB/D-Sub 、 RGB/DVI-I 、 PS2 、 A/V Cable 12 13

FCC ID : BEJMW60SZ12 Page 1 of 41 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 TEST REPORT FOR CERTIFICATION (FCC CFR47 PART 15 DIGITAL DEVICE) On Behalf of LG Electronics USA LCD Projection Monitor ModelMW-60SZ12 FCC IDBEJMW60SZ12 Brand: LG Prepared for : LG Electronics USA 6133 N River Rd., Suite 1100, Rosemont IL US. Prepared by : Taiwan Tokin EMC Eng. Corp. No. 53-11, Tin-Fu Tsun, Lin-Kou, Taipei Hsien, Taiwan, R.O.C. Tel: (02) 2609-9301, 2609-2133 Fax: (02) 2609-9303 File Number ATM-G91807 Report Number TTEMC-F91136 Date of Test Aug. 27 ~Sep. 10, 2002 Date of Report Sep. 13, 2002 FCC ID : BEJMW60SZ12 Page 2 of 41 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 TABLE OF CONTENTS Description Page TEST REPORT CERTIFICATION.......................................................................................................3 1. GENERAL INFORMATION.........................................................................................................4 1.1. Description of Device (EUT)..........................................................................................................4 1.2. Tested Supporting System Details...................................................................................................5 1.3. Description of Test Facility............................................................................................................7 1.4. Measurement Uncertainty..............................................................................................................8 2. POWERLINE CONDUCTED TEST.............................................................................................9 2.1. Test Equipment.............................................................................................................................9 2.2. Block Diagram of Test Setup..........................................................................................................9 2.3. Powerline Conducted Emission Limit (CISPR 22, Class B)..............................................................9 2.4. EUT’s Configuration during Compliance Measurement.................................................................10 2.5. Operating Condition of EUT........................................................................................................10 2.6. Test Procedure.............................................................................................................................11 2.7. Line Conducted RF Voltage Measurement Results.........................................................................11 3. RADIATED EMISSION TEST....................................................................................................24 3.1. Test Equipment...........................................................................................................................24 3.2. Block Diagram of Test Setup........................................................................................................24 3.3. Radiated Emission Limit (CISPR 22, Class B)...............................................................................25 3.4. EUT’s Configuration during Compliance Measurement.................................................................25 3.5. Operating Condition of EUT........................................................................................................25 3.6. Test Procedure.............................................................................................................................26 3.7. Radiated Emission Measurement Results......................................................................................27 4. MODIFICATIONS TO EUT........................................................................................................31 5. DEVIATION TO TEST SPECIFICATIONS.............................................................................32 6. PHOTOGRAPHS..........................................................................................................................33 6.1. Photos of Powerline Conducted Measurement...............................................................................33 6.2. Photos of Radiated Measurement at Open Field Test Site...............................................................35 6.3. Photos of Radiated Measurement at Semi-Anechoic Chamber........................................................39 APPENDIX I (Radiated Test Data at Semi-Anechoic Chamber)........................................................41 FCC ID : BEJMW60SZ12 Page 3 of 41 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 TEST REPORT CERTIFICATION Applicant LG Electronics USA Manufacturer LG Electronics Inc. FCC ID BEJMW60SZ12 EUT Description LCD Projection Monitor (A) MODEL NO. MW-60SZ12 (B) SERIAL NO. N/A (C) BRAND LG (D) POWER SUPPLY AC 120V, 60Hz Measurement Procedure Used: FCC RULES AND CISPR 22 (DOCKET NO. 92-152, SEP. 1993) AND FCC / ANSI C63.4-1992 (FCC CFR 47 Part 15 Subpart B/2002 and CISPR 22/1997 +A1/2000) The device described above was tested by TAIWAN TOKIN EMC ENG. CORP. to determine the maximum emission levels emanating from the device. The maximum emission levels were compared to the CISPR 22 Class B limits both radiated and conducted emissions. The measurement results are contained in this test report and TAIWAN TOKIN EMC ENG. CORP. is assumed full responsibility for the accuracy and completeness of these measurements. Also, this report shows that the EUT to be technically compliance with the FCC official limits. This report applies to above tested sample only. This report shall not be reproduced in part without written approval of Taiwan Tokin EMC Eng. Corp. (NOTE: These results are deemed satisfactory evidence of compliance with ICES-003 of the Canadian Interference-Causing Equipment Regulations.) Date of Test : Aug. 27 ~ Sep. 10, 2002 Prepared By: (Cherry Wang/Assistant Manager) Test Engineer: (Allen Wang/Deputy Manager) Approve & …

Text truncated - open the document above for the full version.

FCC ID.: BEJMW60SZ12 APPENDIX I-1/12 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 FCC ID.: BEJMW60SZ12 APPENDIX I-2/12 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 FCC ID.: BEJMW60SZ12 APPENDIX I-3/12 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 FCC ID.: BEJMW60SZ12 APPENDIX I-4/12 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 FCC ID.: BEJMW60SZ12 APPENDIX I-5/12 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 FCC ID.: BEJMW60SZ12 APPENDIX I-6/12 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 FCC ID.: BEJMW60SZ12 APPENDIX I-7/12 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 FCC ID.: BEJMW60SZ12 APPENDIX I-8/12 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 FCC ID.: BEJMW60SZ12 APPENDIX I-9/12 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 FCC ID.: BEJMW60SZ12 APPENDIX I-10/12 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 FCC ID.: BEJMW60SZ12 APPENDIX I-11/12 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 FCC ID.: BEJMW60SZ12 APPENDIX I-12/12 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136

FCC ID : BEJMW60SZ12 Page 33 of 41 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 6. PHOTOGRAPHS 6.1. Photos of Powerline Conducted Measurement Test ModeRGB IN (D-Sub or DVI-I) FRONT VIEW OF CONDUCTED TEST BACK VIEW OF CONDUCTED TEST FCC ID : BEJMW60SZ12 Page 34 of 41 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 Test ModeA/VS-VideoComponent Input FRONT VIEW OF CONDUCTED TEST BACK VIEW OF CONDUCTED TEST FCC ID : BEJMW60SZ12 Page 35 of 41 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 6.2. Photos of Radiated Measurement at Open Field Test Site Test ModeRGB IN1 (D-Sub), 1280*1024/60Hz, 64kHz FRONT VIEW OF RADIATED TEST BACK VIEW OF RADIATED TEST FCC ID : BEJMW60SZ12 Page 36 of 41 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 Test ModeRGB IN1 (D-Sub), 1280*1024/60Hz, 64kHz SETUP WITH MAXIMUM DETECTED EMMISSION AT HORIZONTAL POLARIZATION SETUP WITH MAXIMUM DETECTED EMMISSION AT VERTICAL POLARIZATION FCC ID : BEJMW60SZ12 Page 37 of 41 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 Test ModeComponent Input, (Image “DVD Movie”) FRONT VIEW OF RADIATED TEST BACK VIEW OF RADIATED TEST FCC ID : BEJMW60SZ12 Page 38 of 41 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 Test ModeComponent Input, (Image “DVD Movie”) SETUP WITH MAXIMUM DETECTED EMMISSION AT HORIZONTAL POLARIZATION SETUP WITH MAXIMUM DETECTED EMMISSION AT VERTICAL POLARIZATION FCC ID : BEJMW60SZ12 Page 39 of 41 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 6.3. Photos of Radiated Measurement at Semi-Anechoic Chamber Test ModeRGB IN (D-Sub or DVI-I) FRONT VIEW OF RADIATED TEST BACK VIEW OF RADIATED TEST FCC ID : BEJMW60SZ12 Page 40 of 41 Taiwan Tokin EMC Eng. Corp. Report No.: TTEMC-F91136 Test ModeA/VS-VideoComponent Input FRONT VIEW OF RADIATED TEST BACK VIEW OF RADIATED TEST