BYMBP2G4AWireless intercom beltpack

FreeSpeak II™ Base Station Version Part Number: 399G087 Rev 22 Date: April 02, 2015 User Guide User Guide | FreeSpeak II™ Page 2 Document Reference Clear-Com FreeSpeak II User Guide Part Number: 399G087 Revision: 22 Legal Disclaimers Copyright © 2015 HME Clear-Com Ltd. All rights reserved. Clear-Com and the Clear-Com logo are registered trademarks of HM Electronics, Inc. The software described in this document is furnished under a license agreement and may be used only in accordance with the terms of the agreement. The product described in this document is distributed under licenses restricting its use, copying, distribution, and decompilation/reverse engineering. No part of this document may be reproduced in any form by any means without prior written authorization of Clear-Com, an HME Company. Clear-Com Offices are located in California, USA; Cambridge, UK; Dubai, UAE; Montreal, Canada; and Beijing, China. Specific addresses and contact information can be found on Clear-Com’s corporate website: www.clearcom.com Clear-Com Contacts Americas and Asia-Pacific Headquarters California, United States Tel: +1.510.337.6600 Email: [email protected] Europe, Middle East, and Africa Headquarters Cambridge, United Kingdom Tel: +44 1223 815000 Email: [email protected] Canada Office Quebec , Canada Tel: +1 (450) 653-9669 China Office Beijing Representative Office Beijing, P.R.China Tel: +8610 65811360 / 65815577 User Guide | FreeSpeak II™ Page 3 Contents Document Reference ..................................................................... 2 1 Important Safety instructions ................................... 10 1.1 Safety symbols ............................................................ 11 2 Introduction to FreeSpeak II™ .................................. 12 2.1 An FS II communication system ...................................... 13 2.1.1 FreeSpeak II system capacity ........................................... 14 3 Installing a system .................................................... 14 3.1 Placing the Base station ................................................. 16 3.2 Placing the antennas and splitters ................................... 16 3.2.1 Wiring the antennas and splitters ...................................... 17 3.2.2 Power supplies to the components of an FS II System .......... 18 3.2.3 Determining coverage areas ............................................. 19 3.3 Doing a site survey to determine coverage areas .............. 20 3.3.1 Doing a site survey with a beltpack .................................... 20 3.3.2 Testing antenna handoff .................................................. 22 3.3.3 Getting information on active antenna status ...................... 23 3.3.4 Assigning beltpacks to coverage areas ............................... 23 3.3.5 Conditions affecting coverage areas ................................... 24 3.4 Registering beltpacks .................................................... 24 3.4.1 Over the air (OTA) registration of a beltpack from the Base station ........................................................................... 25 4 Connecting the Base station ...................................... 28 4.1 Understanding the Back-Panel Connectors ....................... 29 4.2 Connecting to partyline intercom systems ........................ 32 4.2.1 Clear-Com and compatible partyline .................................. 32 4.2.2 Connecting directly to Clear-Com partyline beltpacks ........... 33 4.2.3 Connecting to an RTS™ wired beltpack ............................... 34 User Guide | FreeSpeak II™ Page 4 4.2.4 Front-panel adjustments for partyline connections ............... 35 4.2.5 Troubleshooting partyline connections ................................ 35 4.3 Wireless partyline ......................................................... 37 4.4 Connecting to 4-Wire and digital matrix intercom .............. 38 4.4.2 Connecting to Clear-Com matrix plus ................................. 40 4.4.3 Connecting to Clear-Com Eclipse digital matrix .................... 40 4.4.4 Connecting with other digital matrix intercom systems ......... 41 4.4.5 Connecting with other 4-wire devices ................................. 41 4.5 Connecting to a program audio source ............................. 42 4.6 IFB configuration .......................................................... 42 4.7 Connecting to the stage announce output ........................ 43 4.8 Connecting to a PC ....................................................... 44 4.8.1 Connecting using the serial port ........................................ 44 4.8.2 Connecting using the LAN port .......................................... 46 4.9 Connecting to transceiver/antennas ................................ 46 4.9.1 Connecting one transceiver/antenna directly to a transceiver port .............................................................................. 46 4.9.2 Connecting transceiver/antennas with a splitter (PD2203) ..... 47 4.9.3 Powering an antenna or antenna splitter ............................. 48 5 Operating the Base station ........................................ 49 5.1 Introduction ................................................................. 49 5.2 Understanding Front-Panel Operation .............................. 50 5.2.1 Call Channel A ................................................................ 50 5.2.2 Call Channel B ................................................................ 50 6 Programming a system from the Base station ........... 54 6.1 Introduction ................................................................. 55 6.2 Using the Base station’s programming menus ................... 56 6.3 Saving changes ............................................................ 56 6.4 Changing beltpack labels ............................................... 56 6.4.1 To change a beltpack label ............................................... 56 6.5 Setting and changin…

Text truncated - open the document above for the full version.

FSll-BP24-NA Rev 1 MODEL: BP2G4A "Only use adapter/batteries listed in the user manual" FCC \D: BYMBP2G4A tC: 1860A-BP2G4A LED 'N U.S.A. ..... FCC 0: BYMB~ IC: 1860A-8~ +

802 N. Twin Oaks Valley Road, Suite 105 • San Marcos, CA 92069 • U.S.A. TEL (760) 471-2100 • FAX (760) 471-2121 http://www.rfexposurelab.com CERTIFICATE OF COMPLIANCE SAR EVALUATION HM Electronics, Inc. Dates of Test: March 26-27, 2015 14110 Stowe Drive Test Report Number: SAR.20150309 Poway, CA 92064 Revision D This wireless mobile and/or portable device has been shown to be compliant for localized specific absorption rate (SAR) for uncontrolled environment/general exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in IEEE 1528-2013 and IEC 62209-2:2010 (See test report). I attest to the accuracy of the data. All measurements were performed by myself or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. RF Exposure Lab, LLC certifies that no party to this application is subject to a denial of Federal benefits that includes FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Jay M. Moulton Vice President Testing Cert. # 2387.01 FCC ID: BYMBP2G4A IC Certificate: 1860A-BP2G4A Model(s): BP2G4A Test Sample: Engineering Unit Same as Production Serial Number: F10TC008 Equipment Type: Wireless Belt Pack Classification: Portable Transmitter Next to Body TX Frequency Range: 2403.65 – 2479.68 MHz; 2401 – 2480 MHz Frequency Tolerance: ± 2.5 ppm Maximum RF Output: 2450 MHz (GFSK) – 20.56 dB, 2450 MHz (BT) – 5.81 dB Conducted Signal Modulation: GFSK Antenna Type: Internal Application Type: Certification FCC Rule Parts: Part 2, 15C KDB Test Methodology: KDB 447498 D01 v05 Industry Canada: RSS-102, Safety Code 6 Maximum SAR Value: 0.02 W/kg Reported Max. Simultaneous SAR: 0.03 W/kg Reported Separation Distance: 0 mm © 2015 RF Exposure Lab, LLC This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. Report Number: SAR.20150309 Table of Contents 1. Introduction ........................................................................................................................ 3 SAR Definition [5] ................................................................................................................... 4 2. SAR Measurement Setup ................................................................................................... 5 Robotic System ...................................................................................................................... 5 System Hardware ................................................................................................................... 5 System Electronics ................................................................................................................. 6 Probe Measurement System .................................................................................................. 6 3. Probe and Dipole Calibration .............................................................................................14 4. Phantom & Simulating Tissue Specifications .....................................................................15 Head & Body Simulating Mixture Characterization ................................................................15 5. ANSI/IEEE C95.1 – 1992 RF Exposure Limits [2] ..............................................................16 Uncontrolled Environment .....................................................................................................16 Controlled Environment .........................................................................................................16 6. Measurement Uncertainty .................................................................................................17 7. System Validation..............................................................................................................18 Tissue Verification .................................................................................................................18 Test System Verification ........................................................................................................18 8. SAR Test Data Summary ..................................................................................................19 Procedures Used To Establish Test Signal ...........................................................................19 Device Test Condition ...........................................................................................................19 SAR Data Summary – 2450 MHz Body .................................................................................21 SAR Data Summary – Simultaneous Evaluation ...................................................................22 9. Test Equipment List ...........................................................................................................23 10. Conclusion ....................................................................................................................24 11. References ....................................................................................................................25 Appendix A – System Validation Plots and Data .......................................................................26 Appendix B – SAR Test Data Plots ...........................................................................................29 Appendix C – SAR Test Setup Photos ......................................................................................31 Appendix D – Probe Calibration Data Sheets ............................................................................36 Appendix E – Dipole Calibration Data Sheets ...........................................................................48 Appendix F – Phantom Calibration Data Sheets ......................................…

Text truncated - open the document above for the full version.

Nemko Test Report: 2015_281257A_FCC_15247 Applicant: HM Electronics, Inc. 14110 Stowe Drive Poway, CA 92064 USA Equipment Under Test: BP2G4A (E.U.T.) FCC Identifier: BYMBP2G4A IC Identifier: 1860A-BP2G4A In Accordance With: FCC Part 15, Subpart C, 15.247 and Industry Canada RSS-210, Issue 8 Frequency Hopping Transmitters Tested By: Nemko USA, Inc. 2210 Faraday Ave. Ste 150 Carlsbad, CA 92008 USA TESTED BY: DATE: 22 March 2015 David Light, Wireless Engineer APPROVED BY: DATE: 30 March 2015 Jim Morris, EMC Manager Total Number of Pages: 37 Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada RSS-210 Issue 8 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER EQUIPMENT: BP2G4A PROJECT NO.: 2015_281257A_FCC_15247 Page 2 of 37 Table of Contents SECTION 1. SUMMARY OF TEST RESULTS 3 SECTION 2. EQUIPMENT UNDER TEST (E.U.T.) 5 SECTION 3. CHANNEL SEPARATION 6 SECTION 4. TIME OF OCCUPANCY 11 SECTION 5. PEAK POWER OUTPUT 15 SECTION 6. SPURIOUS EMISSIONS (CONDUCTED) 19 SECTION 7. SPURIOUS EMISSIONS (RADIATED) 24 SECTION 8. TEST EQUIPMENT LIST 26 ANNEX A - TEST DETAILS 27 ANNEX B - TEST DIAGRAMS 35 Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada RSS-210 Issue 8 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER EQUIPMENT: BP2G4A PROJECT NO.: 2015_281257A_FCC_15247 Page 3 of 37 Section 1. Summary of Test Results Manufacturer: HM Electronics, Inc. Model No.: BP2G4A Serial No.: None General: All measurements are traceable to national standards. These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 15, Subpart C, Paragraph 15.247 and Industry Canada RSS-210, Issue 8 for Frequency Hopping Spread Spectrum devices. Radiated tests were conducted is accordance with ANSI C63.10:2013. Radiated emissions are made on an open area test site. A description of the test facility is on file with the FCC and Industry Canada. New Submission Production Unit Class II Permissive Change Pre-Production Unit THIS TEST REPORT RELATES ONLY TO THE ITEM(S) TESTED. THE FOLLOWING DEVIATIONS FROM, ADDITIONS TO, OR EXCLUSIONS FROM THE TEST SPECIFICATIONS HAVE BEEN MADE. See “ Summary of Test Data”. NVLAP Lab Code 200116-0 This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. Nemko USA, Inc. is a NVLAP accredited laboratory. Nemko USA Inc. authorizes the above named company to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko USA Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. This report applies only to the items tested. Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada RSS-210 Issue 8 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER EQUIPMENT: BP2G4A PROJECT NO.: 2015_281257A_FCC_15247 Page 4 of 37 Summary Of Test Data NAME OF TEST PARA. NO. RESULT Powerline Conducted Emissions 15.207(a) / RSS-Gen 7.2.4 NA Channel Separation 15.247(a)(1) / RSS-210 A8.1(b) Complies Time of Occupancy 15.247(a)(1) / RSS-210 A8.1(d) Complies 20 dB Occupied Bandwidth 15.247(a)(1) / RSS-210 A8.1(a) Complies Peak Power Output 15.247(b) / RSS-210 A8.4(2) Complies Spurious Emissions (Conducted) 15.247(d) / RSS-210 A8.5 Complies Spurious Emissions (Radiated) 15.247(d) / RSS-Gen 7.2.2 Complies Footnotes: The EUT is powered by a 3.7 V lithium battery. Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada RSS-210 Issue 8 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER EQUIPMENT: BP2G4A PROJECT NO.: 2015_281257A_FCC_15247 Page 5 of 37 Section 2. Equipment Under Test (E.U.T.) General Equipment Information Frequency Band: 902 – 928 MHz 2400 – 2483.5 MHz 5725 – 5850 MHz Operating Frequency Range: 2403.648 to 2479.68 MHz Number of Channels: 45 Channel Spacing: 1.728 MHz User Frequency Adjustment: Software controlled Software/firmware version: Ver. 0020 Description of EUT Wireless Intercom Beltpack used for Pro-Audio Communications Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada RSS-210 Issue 8 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER EQUIPMENT: BP2G4A PROJECT NO.: 2015_281257A_FCC_15247 Page 6 of 37 Section 3. Channel Separation NAME OF TEST: Channel Separation PARA. NO.: 15.247(a)(1) TESTED BY: David Light DATE: 17-20 March 2015 Test Results: Complies. Measurement Data: See 20 dB BW plot Measured 20 dB bandwidth: 1.38 MHz Channel Separation: 1.728 MHz Equipment Used: 1036 Measurement Uncertainty: 0.20 ms Temperature: 20 C Relative Humidity: 30 % Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada RSS-210 Issue 8 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER EQUIPMENT: BP2G4A PROJECT NO.: 2015_281257A_FCC_15247 Page 7 of 37 Test Data – Channel Separation 22.3 dB Offset A Unit dBm 1MA SWT 5 ms 1MAX Start 2.401 GHzStop 2.415 GHz1.4 MHz/ Ref Lvl 30 dBm Ref Lvl 30 dBm RBW 300 kHz VBW 300 kHz RF Att 30 dB IN1 -60 -50 -40 -30 -20 -10 0 10 20 -70 30 1 1 Delta 1 [T1] 1.14 dB 1.75000000 MHz 1 [T1] 15.94 dBm 2.40534870 GHz 1 [T1] 1.14 dB 1.75000000 MHz Date: 17.MAR.2015 10:02:58 Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada RSS-210 Issue 8 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER EQUIPMENT: BP2G4A PROJECT NO.: 2015_281257A_FCC_15247 Page 8 of 37 Test Data – 20 dB Bandwidth Low Channel Ref Lvl 30 dBm Ref Lvl 30 dBm RBW 50 kHz VBW 100 kHz SWT 5 ms RF Att 20 dB 500 kHz/Center 2.403648297 GHzSpan 5 MHz 22.1 dB Offset A IN1 Unit dBm 1VIEW1MA -60 -50 -40 -30 -20 -10 0 10 20 -70 30 1 1 Delta 1 [T1] 3.38 dB 1.31262525 MHz 1 [T1] -6.17 dBm 2.40299198 GHz 1 [T1] 3.38 dB 1.31262525 MHz Date: 28.MAR.2015 10:32:41 Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada RSS-210 Issue 8 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER EQUIPMENT: BP2G4A PROJECT NO.: 2015_281257A_FCC_15247 …

Text truncated - open the document above for the full version.

Nemko Test Report: 2015_281257B_FCC_15247 Applicant: HM Electronics, Inc. 14110 Stowe Drive Poway, CA 92064 USA Equipment Under Test: BP2G4A (E.U.T.) FCC Identifier: BYMBP2G4A IC Identifier: 1860A-BP2G4A In Accordance With: FCC Part 15, Subpart C, 15.247 and Industry Canada RSS-210, Issue 8 Frequency Hopping Transmitters Tested By: Nemko USA, Inc. 2210 Faraday Ave. Ste 150 Carlsbad, CA 92008 USA TESTED BY: DATE: 22 March 2015 David Light, Wireless Engineer APPROVED BY: DATE: 30 March 2015 Jim Morris, EMC Manager Total Number of Pages: 57 Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada RSS-210 Issue 8 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER EQUIPMENT: BP2G4A PROJECT NO.: 2015_281257B_FCC_15247 Table of Contents SECTION 1. SUMMARY OF TEST RESULTS 3 SECTION 2. EQUIPMENT UNDER TEST (E.U.T.) 5 SECTION 3. CHANNEL SEPARATION 6 SECTION 4. TIME OF OCCUPANCY 17 SECTION 5. PEAK POWER OUTPUT 21 SECTION 6. SPURIOUS EMISSIONS (CONDUCTED) 31 SECTION 7. SPURIOUS EMISSIONS (RADIATED) 44 SECTION 8. TEST EQUIPMENT LIST 46 ANNEX A - TEST DETAILS 47 ANNEX B - TEST DIAGRAMS 55 Page 2 of 57 Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada RSS-210 Issue 8 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER EQUIPMENT: BP2G4A PROJECT NO.: 2015_281257B_FCC_15247 Section 1. Summary of Test Results Manufacturer: HM Electronics, Inc. Model No.: BP2G4A Serial No.: None General: All measurements are traceable to national standards. These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 15, Subpart C, Paragraph 15.247 and Industry Canada RSS-210, Issue 8 for Frequency Hopping Spread Spectrum devices. Radiated tests were conducted is accordance with ANSI C63.10: 2013. Radiated emissions are made on an open area test site. A description of the test facility is on file with the FCC and Industry Canada. New Submission Production Unit Class II Permissive Change Pre-Production Unit THIS TEST REPORT RELATES ONLY TO THE ITEM(S) TESTED. THE FOLLOWING DEVIATIONS FROM, ADDITIONS TO, OR EXCLUSIONS FROM THE TEST SPECIFICATIONS HAVE BEEN MADE. See “ Summary of Test Data”. NVLAP Lab Code 200116-0 This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. Nemko USA, Inc. is a NVLAP accredited laboratory. Nemko USA Inc. authorizes the above named company to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko USA Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. This report applies only to the items tested. Page 3 of 57 Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada RSS-210 Issue 8 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER EQUIPMENT: BP2G4A PROJECT NO.: 2015_281257B_FCC_15247 Summary Of Test Data NAME OF TEST PARA. NO. RESULT Powerline Conducted Emissions 15.207(a) / RSS-Gen 7.2.4 NA Channel Separation 15.247(a)(1) / RSS-210 A8.1(b) Complies Time of Occupancy 15.247(a)(1) / RSS-210 A8.1(d) Complies 20 dB Occupied Bandwidth 15.247(a)(1) / RSS-210 A8.1(a) Complies Peak Power Output 15.247(b) / RSS-210 A8.4(2) Complies Spurious Emissions (Conducted) 15.247(d) / RSS-210 A8.5 Complies Spurious Emissions (Radiated) 15.247(d) / RSS-Gen 7.2.2 Complies Footnotes: The EUT is powered by a 3.7 V lithium battery. Page 4 of 57 Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada RSS-210 Issue 8 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER EQUIPMENT: BP2G4A PROJECT NO.: 2015_281257B_FCC_15247 Section 2. Equipment Under Test (E.U.T.) General Equipment Information Frequency Band: 902 – 928 MHz 2400 – 2483.5 MHz 5725 – 5850 MHz Operating Frequency Range: 24012 to 2480 MHz Number of Channels: 79 Channel Spacing: 1 MHz User Frequency Adjustment: Software controlled Software/firmware version: Ver. 0020 Description of EUT Wireless Intercom Beltpack used for Pro-Audio Communications Page 5 of 57 Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada RSS-210 Issue 8 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER EQUIPMENT: BP2G4A PROJECT NO.: 2015_281257B_FCC_15247 Section 3. Channel Separation NAME OF TEST: Channel Separation PARA. NO.: 15.247(a)(1) TESTED BY: David Light DATE: 17 March 2015 Test Results: Complies. Measurement Data: See 20 dB BW plot Measured 20 dB bandwidth: 0.971 MHz GFSK 1.3 MHz π/4-DQPSK 1.3 MHz 8-DPSK Channel Separation: 1 MHz Equipment Used: 1036 Measurement Uncertainty: 0.20 ms Temperature: 20 °C Relative Humidity: 30 % Page 6 of 57 Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada RSS-210 Issue 8 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER EQUIPMENT: BP2G4A PROJECT NO.: 2015_281257B_FCC_15247 Test Data – Channel Separation 22.3 dB Offset A Un i t dBm Ref Lvl 3 0 d Bm Ref Lvl 3 0 d Bm R F A tt 30 dB SWT 5 m s 1MA 1MA X Center2 .441 GHzSpan5 M Hz5 00 kHz/ RBW 10 0 k Hz VB W 100 kHz IN 1 - 60 -50 -40 -30 -2 0 -10 0 10 20 -70 30 1 1 Delta 1 [T1] 0. 4 8 dB -1.03006012 MHz 1 [T1] 7.85 dBm 2. 44089980 GHz 1 [T1] 0.48 dB - 1 .03006012 MHz Date: 1 7.MA R.2015 08:51:29 Page 7 of 57 Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada RSS-210 Issue 8 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER EQUIPMENT: BP2G4A PROJECT NO.: 2015_281257B_FCC_15247 Test Data – 20 dB Bandwidth Low Channel QPSK 1MAX R ef L vl 30 dBm R ef L vl 30 dBm RBW 50 kHz V B W 50 k H z SWT 5 ms RF A tt 3 0 d B 5 00 kH z/ Center2 .4019 2 G Hz Spa n 5 MHz 2 2. 3 d B Offset A IN1 1M A Unit d Bm -60 -50 -40 -30 -20 -10 0 10 20 -70 30 1 1 De lt a 1 [ T 1] -1.16 dB 1 . 38 276553 MHz 1 [ T1] -1.47 dBm 2.4 01 2 33 6 3 GH z 1 [ T1] -1.16 dB 1.3 8 27 65 5 3 MH z Date : 20.MAR.2015 08 :01: 28 Page 8 of 57 Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada RSS-210 Issue 8 FREQUE…

Text truncated - open the document above for the full version.