BYMBP850BELTPACK TRANSCEIVER

HME# 400520 Rev − 7/7/03 PRO850 Wireless Intercom Operating Instructions Table of Contents SECTION 1. INTRODUCTION ....................................................................................................................1 EQUIPMENT FEATURES ................................................................................................................................2 Base Station Front Panel Features ..................................................................................................................2 Base Station Rear Panel Features ...................................................................................................................2 Beltpac Top Panel Features ............................................................................................................................3 Beltpac Bottom Panel Features.......................................................................................................................3 BLOCK DIAGRAMS ........................................................................................................................................4 Base Station ....................................................................................................................................................4 Beltpac............................................................................................................................................................4 EQUIPMENT SPECIFICATIONS ....................................................................................................................5 Base Station ....................................................................................................................................................5 Beltpac............................................................................................................................................................6 SECTION 2. EQUIPMENT SETUP..............................................................................................................7 BASE STATION SETUP...................................................................................................................................7 Checking Status .......................................................................................................................................11 Monitoring Audio Levels ........................................................................................................................12 Base Transmitter Configuration ..............................................................................................................13 Base Receiver Configuration...................................................................................................................14 Base Configuration..................................................................................................................................15 Beltpac Configuration .............................................................................................................................18 Saving and Loading Settings ...................................................................................................................21 Advanced Settings ...................................................................................................................................21 Displaying Information ...........................................................................................................................25 Diagnostics ..............................................................................................................................................25 SECTION 3. PRO850 OPERATION............................................................................................................9 BASE STATION OPERATION ........................................................................................................................9 Uses of Front Panel Controls, Indicators and Connectors ..............................................................................9 Display Screen Navigation ...........................................................................................................................10 Display Screen Functions and System Settings ............................................................................................11 BELTPAC OPERATION.................................................................................................................................26 Controls and Buttons ....................................................................................................................................26 Indicator Lights ............................................................................................................................................27 Connectors and Adjustment..........................................................................................................................28 Batteries........................................................................................................................................................29 Infrared Window ..........................................................................................................................................29 SECTION 4. PC850 SOFTWARE ...............................................................................................................30 PC850 Installation ........................................................................................................................................30 PC850 Operation ..........................................................................................................................................31 END-USER LICENSE AGREEMENT FOR HME PC850 SOFTWARE...................................................33 Copyright HM Electronics, Inc. - July 2003 FCC LICENSING The HME PRO850 is …

Text truncated - open the document above for the full version.

August 25, 2003 HM Electronics, Inc. PRO850 Beltpac (BP850) FCC ID label:

BYMBP850 MAIN PCB (FRONT) -INTERNAL BYMBP850 MAIN PCB (FRONT) -INTERNAL BYMBP850 MAIN PCB (BACK) -INTERNAL BYMBP850 MAIN PCB (BACK) -INTERNAL BYMBP850 FRONT VIEW –AUX BRD BYMBP850 FRONT VIEW –AUX BRD BYMBP850 BACK VIEW –AUX BRD BYMBP850 BACK VIEW –AUX BRD BYMBP850 HEADSET CONNECTOR BYMBP850 HEADSET CONNECTOR

FCC ID: BYMBP850 MFA p0370004, d0380033 Transmitter Certification of FCC ID: BYMBP850 Model: BP850 to Federal Communications Commission Rule Part(s) 74H, Confidentiality Date of report: August 18, 2003 On the Behalf of the Applicant: HM Electronics, Inc. At the Request of: P.O. Part of 20213 HM Electronics, Inc. 14110 Stowe Drive Poway, CA 92064 Attention of: (858) 535-6000 Corporate Tom Riches, Engineering Services manager (858) 535-6098; FAX: -9019 email: [email protected] Supervised by: Morton Flom, P. Eng. FCC ID: BYMBP850 MFA p0370004, d0380033 List of Exhibits (FCC Certification (Transmitters) - Revised 9/28/98) Applicant: HM Electronics, Inc. FCC ID: BYMBP850 By Applicant: 1. Letter of Authorization x 2. Identification Drawings, 2.1033(c)(11) x Label x Location of Label x Compliance Statement x Location of Compliance Statement 3. Photographs, 2.1033(c)(12) x 4. Documentation: 2.1033(c) (3) User Manual x (9) Tune Up Info x (10) Schematic Diagram x (10) Circuit Description x Block Diagram x Parts List x Active Devices x By M.F.A. Inc.: A. Testimonial & Statement of Certification B. Statement of Qualifications FCC ID: BYMBP850 MFA p0370004, d0380033 The Applicant has been cautioned as to the following: 15.21 Information to the User. The users manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.27(a) Special Accessories. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer, without additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. FCC ID: BYMBP850 MFA p0370004, d0380033 Table of Contents Rule Description Page . Test Report 1 2.1033(c) General Information Required 2 2.1033(c)(14) Rule Summary 5 . Standard Test Conditions and Engineering Practices 6 2.1046(a) Carrier Output Power (Conducted) 7 2.1046(a) ERP Carrier Power (Radiated) 9 2.1053(a) Field Strength of Spurious Radiation 10 2.1049(c)(1) Emission Masks (Occupied Bandwidth) 14 2.1055(a)(1) Frequency Stability (Temperature Variation) 18 2.202(g) Necessary Bandwidth and Emission Bandwidth 22 FCC ID: BYMBP850 MFA p0370004, d0380033 Page Number 1 of 22. Required information per ISO/IEC Guide 25-1990, paragraph 13.2: a) Test Report b) Laboratory: (FCC: 31040/SIT) (Canada: IC 2044) M. Flom Associates, Inc. 3356 N. San Marcos Place, Suite 107 Chandler, AZ 85225 c) Report Number: d0380033 d) Client: HM Electronics, Inc. 14110 Stowe Drive Poway, CA 92064 e) Identification: BP850 FCC ID: BYMBP850 EUT Description: f) EUT Condition: Not required unless specified in individual tests. g) Report Date: August 18, 2003 EUT Received: July 14, 2003 h, j, k): As indicated in individual tests. i) Sampling method: No sampling procedure used. l) Uncertainty: In accordance with MFA internal quality manual. m) Supervised by: Morton Flom, P. Eng. n) Results: The results presented in this report relate only to the item tested. o) Reproduction: This report must not be reproduced, except in full, without written permission from this laboratory. FCC ID: BYMBP850 MFA p0370004, d0380033 Page Number 2 of 22. List of General Information Required for Certification In Accordance with FCC Rules and Regulations, Volume II, Part 2 and to 74H, Confidentiality Sub-part 2.1033 (c)(1): Name and Address of Applicant: HM Electronics, Inc. 14110 Stowe Drive Poway, CA 92064 Manufacturer: Applicant (c)(2): FCC ID: BYMBP850 Model Number: BP850 (c)(3): Instruction Manual(s): Please see attached exhibits (c)(4): Type of Emission: 190KF9W (c)(5): Frequency Range, MHz: 470 to 608 614 to 740 (c)(6): Power Rating, Watts: 0.100 Switchable Variable N/A (c)(7): Maximum Power Rating, Watts: 0.250 DUT Results: Passes x Fails FCC ID: BYMBP850 MFA p0370004, d0380033 Page Number 3 of 22. M. Flom Associates, Inc. is accredited by the American Association for Laboratory Association (A2LA) as shown in the scope below. "This laboratory is accredited by the American Association for Laboratory Accreditation (A2LA) and the results shown in this report have been determined in accordance with the laboratory's terms of accreditation unless stated otherwise in the report." Should this report contain any data for tests for which we are not accredited, or which have been undertaken by a subcontractor that is not A2LA accredited, such data would not covered by this laboratory's A2LA accreditation. FCC ID: BYMBP850 MFA p0370004, d0380033 Page Number 4 of 22. Subpart 2.1033 (continued) (c)(8): Voltages & currents in all elements in final RF stage, including final transistor or solid-state device: Collector Current, A = per manual Collector Voltage, Vdc = per manual Supply Voltage, Vdc = 6 (c)(9): Tune-Up Procedure: Please…

Text truncated - open the document above for the full version.