BYMXCVR1G9Wireless Intercom System

FreeSpeak II™ User Guide (Base station version) PN: 399G087 Rev 9 06/16/14 Document Reference Clear-Com FreeSpeak II User Guide Part Number: 399G087 Revision: 9 Legal Disclaimers Copyright © 2014 HME Clear-Com Ltd. All rights reserved. Clear-Com, the Clear-Com logo, Clear-Com Concert and HelixNet are registered trademarks of HM Electronics, Inc. The software described in this document is furnished under a license agreement and may be used only in accordance with the terms of the agreement. The product described in this document is distributed under licenses restricting its use, copying, distribution, and decompilation/reverse engineering. No part of this document may be reproduced in any form by any means without prior written authorization of Clear-Com, an HME Company. Clear-Com Offices are located in California, USA; Cambridge, UK; Dubai, UAE, Montreal, Canada; and Beijing, China. Specific addresses and contact information can be found on Clear-Com’s corporate website: www.clearcom.com Clear-Com Contacts Americas and Asia-Pacific Headquarters California, United States Tel: +1.510.337.6600 Email: [email protected] Europe, Middle East, and Africa Headquarters Cambridge, United Kingdom Tel: +44 1223 815000 Email: [email protected] Canada Office Quebec , Canada Tel: +1 (450) 653-9669 China Office Beijing Representative Office Beijing, P.R.China Tel: +8610 65811360 / 65815577 2 FreeSpeak II User Guide Contents Document Reference......................................................................................................... 2 1 Important Safety instructions ....................................................................... 9 1.1 Safety symbols .............................................................................................. 10 2 Introduction to FreeSpeak II™ ................................................................... 11 2.1 An FS II communication system .................................................................... 12 3 Installing a system ...................................................................................... 14 3.1 Placing the Base station ................................................................................ 14 3.2 Placing the antennas and splitters ................................................................. 14 3.2.1 Wiring the antennas and splitters ......................................................................... 15 3.2.2 Power supplies to the components of an FS II System ........................................ 15 3.2.3 Determining coverage areas ................................................................................ 17 3.3 Doing a site survey to determine coverage areas .......................................... 18 3.3.1 Doing a site survey with a beltpack ...................................................................... 18 3.3.2 Testing antenna handoff ....................................................................................... 20 3.3.3 Getting information on active antenna status ....................................................... 20 3.3.4 Assigning beltpacks to coverage areas ................................................................ 21 3.3.5 Conditions affecting coverage areas .................................................................... 21 3.4 Registering beltpacks .................................................................................... 21 3.4.1 Over the air (OTA) registration of a beltpack from the Base station .................... 22 4 Connecting the Base station ...................................................................... 24 4.1 Understanding the Back-Panel Connectors ................................................... 25 4.2 Connecting to partyline intercom systems ..................................................... 28 4.2.1 Clear-Com and compatible partyline .................................................................... 28 4.2.2 Connecting directly to Clear-Com partyline beltpacks ......................................... 29 4.2.3 Connecting to an RTS™ wired beltpack .............................................................. 30 4.2.4 Front-panel adjustments for partyline connections............................................... 30 4.2.5 Troubleshooting partyline connections ................................................................. 30 4.3 Wireless partyline .......................................................................................... 32 4.4 Connecting to 4-Wire and digital matrix intercom .......................................... 33 4.4.2 Connecting to Clear-Com matrix plus .................................................................. 34 4.4.3 Connecting to Clear-Com Eclipse digital matrix ................................................... 35 4.4.4 Connecting with other digital matrix intercom systems ........................................ 35 4.4.5 Connecting with other 4-wire devices ................................................................... 36 3 FreeSpeak II User Guide 4.5 Connecting to a program audio source .......................................................... 36 4.6 IFB configuration ........................................................................................... 36 4.7 Connecting to the stage announce output ..................................................... 37 4.8 Connecting to a PC ....................................................................................... 38 4.8.1 Connecting using the serial port ........................................................................... 38 4.8.2 Connecting using the LAN port............................................................................. 39 4.9 Connecting to transceiver/antennas .............................................................. 40 4.9.1 Connecting one transceiver/antenna directly to a transceiver port ...................... 40 4.9.2 Connecting transceiver/an…

Text truncated - open the document above for the full version.

@ Customer Driven DATE June14,2014 Equipment Authorization Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: BYMXCVRIG9 Product Name: XCVR1G9 Request for Confidentialitv Pursuant to Sections 0.457 and 0.459 of the commission's rules, we hereby request that the following documents be held confidential: o Schematics o Block diagram o Bills of Material o OperationalDescription These materials contain trade secrets and proprietary information and customarily released to the public. The public disclosure of this information harmful to the company and provide unjustified benefits to our competitors. are not might be Dated 14 this Dayof June20 14 ritte: { ,,-,, Fl"di - ,',r., F ,i,-,*p On behalf of :HM Electronics, lnc. +1-858-535-6000 HM Electronics, lnc, I p h o n e: 8 0 O. I 4 8 .4 4 6 8 141 l0 Stowe Drive I Poway, CA 92064 I fax:858.452.72O7 | www.hme.com Telephone:

FCC ID: BYMXCVR1G9 Project no.: 256262 Page 1 of 2 EXTERNAL PHOTOS – XCVR1G9 Base Station FCC ID: BYMXCVR1G9 Project no.: 256262 Page 2 of 2

FCC ID: BYMXCVR1G9 Project no.: 256262 Page 2 of 2

FCC ID: BYMXCVR1G9 MPE Calculation for FCC Uncontrolled Environment Formula from page 18 of OET Bulletin 65, Edition 97 -01 where: S = power density P = power input to the antennaG = power gain of the antenna in the direction of i nterest relative to an isotropic radiator R = distance to the center of radiation of the ante nna Source Based Time Averaged Duty Cycle is 100% in ca lculation below Maximum peak output power at antenna input terminal : 20.40 (dBm) Maximum peak output power at antenna input terminal : 0.110 (W) Maximum antenna gain: 2.70 (dBi) Maximum antenna gain: 1.862 (numeric) Prediction distance: 20 (cm) Prediction frequency: 1925 (MHz) Time Averaged Duty Cycle 100 % MPE limit for uncontrolled exposure at prediction f requency: 10.00 (W/m^2) Power density at prediction frequency: 0.0406 (mW/cm^2) Power density at prediction frequency: 0.406 (W/m^2) Maximum allowable antenna gain: 16.61 (dBi) Margin of Compliance: 13.91 (dB) 2 4 R PG S π =

Report No. 256262-1 Template version: B Nemko Norway Nemko AS, Instituttveien 6, P.O. Box 96 Kjeller, 2007 Kjeller, Norway TEL +47 22 96 03 30 FAX +47 22 96 05 50 EMAIL [email protected] ENTERPRISE NUMBER NO974404532 nemko.com/no Test Report Product UPCS Base Station Name and address of the applicant HM Electronics, Inc. 14110 Stowe Drive, Poway, CA 92064 USA Name and address of the manufacturer Same as above Model XCVR1G9 Rating 24 V DC Trademark Clear-Com, An HME Company Serial number / Additional information DECT 6.0 Tested according to FCC Part 15, subpart D Isochronous UPCS Device, 1920 – 1930 MHz Industry Canada RSS 213, Issue 2 2 GHz License-exempt Personal Communications Service Devices (LE-PCS) Order number 256262 Tested in period 2014.03.24 to 2014.03.26 Issue date 2014.06.06 Name and address of the testing laboratory Instituttveien 6 Kjeller, Norway FCC No: 994405 IC OATS: 2040D-1 TEL: (+47) 22 96 03 30 FAX: (+47) 22 96 05 50 Prepared by [Frode Sveinsen] Approved by [G.Suhanthakumar] This report shall not be reproduced except in full without the written approval of Nemko. Opinions and interpretations expressed within this report are not part of the current accreditation. This report was originally distributed electronically with digital signatures. For more information contact Nemko. TEST REPORT FCC part 15D Report no.: 256262-1 FCC ID: BYMXCVR1G9 Nemko Norway, Instituttveien 6, Kjeller, Norway Page 2 (43) CONTENTS 1 INFORMATION ................................................................................................................................. 3 1.1 Tested Item........................................................................................................................................ 3 1.2 Description of Tested Device ............................................................................................................. 3 1.3 Exposure Evaluation .......................................................................................................................... 3 1.4 Test Environment .............................................................................................................................. 4 1.5 Test Engineer(s) ................................................................................................................................ 4 1.6 Test Equipment ................................................................................................................................. 4 1.7 Other Comments ............................................................................................................................... 4 2 TEST REPORT SUMMARY .............................................................................................................. 5 2.1 General .............................................................................................................................................. 5 2.2 Test Summary ................................................................................................................................... 6 3 TEST RESULTS ................................................................................................................................ 7 3.1 Power Line Conducted Emissions ..................................................................................................... 7 3.2 Coordination with fixed microwave .................................................................................................. 10 3.3 Digital Modulation Techniques ........................................................................................................ 10 3.4 Labeling Requirements ................................................................................................................... 10 3.5 Antenna Requirement...................................................................................................................... 11 3.6 Channel Frequencies ...................................................................................................................... 11 3.7 Automatic Discontinuation of Transmission .................................................................................... 12 3.8 Peak Power Output ......................................................................................................................... 13 3.9 Emission Bandwidth B ..................................................................................................................... 16 3.10 Power Spectral Density ................................................................................................................... 19 3.11 In-Band Unwanted Emissions, Conducted ...................................................................................... 22 3.12 Out-of-band Emissions, Conducted................................................................................................. 24 3.13 Carrier Frequency Stability .............................................................................................................. 28 3.14 Frame Repetition Stability ............................................................................................................... 29 3.15 Frame Period and Jitter ................................................................................................................... 29 3.16 Monitoring Threshold, Least Interfered Channel ............................................................................. 31 3.17 Threshold Monitoring Bandwidth ..................................................................................................... 33 3.18 Reaction Time and Monitoring Interval ............................................................................................ 34 3.19 Time and Spectrum Window Access Procedure ............................................................................. 36 3.20 Acknowledgements and Transmission Duration ...................................…

Text truncated - open the document above for the full version.

FCC ID: BYMXCVR1G9 Project no.: 256262 Page 1 of 1 PHOTOS OF TEST SET-UP – XCVR1G9 Base Station Power line Conducted Emissions Test