CNFACCH1Remote Control

Waterproof Shutter Remote U SER GUIDE Installing the Remote Battery 1.Use a coin to unlock the remote’s back panel. Gently press the coin into the slot on the back panel and rotate one quarter turn counter-clockwise. 2.Carefully remove the back panel and install the included battery with the positive (+) flat side of the battery face up. 3.Reinstall the back panel. Use a coin to press and rotate the panel one quarter turn clockwise until the dots align and it clicks into place. Note: Be sure that the door is securely locked and sealed after closing. Heads Up: The battery may stop working at very low temperatures (-4°F/-20°C and below). It may work again after it warms back up. Pairing to Your GoProResetting the Shutter Remote With the remote off and your camera in pairing mode, press the remote’s Power button . The remote’s status light will blink blue every 0.5 seconds to show that it’s in pairing mode. The status light will blink blue every 5 seconds if the pairing was successful. To pair additional cameras (or re-pair your original camera), follow the same steps but press and hold remote’s power button for 3 seconds to put it into pairing mode. Heads Up: HERO11 and earlier cameras cannot be connected to the remote and the GoPro app at the same time. Turning the Shutter Remote On Simply press the remote’s Power button to turn it on. This will also turn on your camera if the remote and camera were connected within the previous 8 hours. If not, turn on your camera. They will pair automatically. The remote’s status light will turn solid blue when scanning for your camera and will blink every 5 seconds after it connects. Recording With the Shutter Remote 1. With your camera on and connected to the remote, simply press the remote’s Shutter button to start capturing with the mode that’s currently active on your camera. 2. Press the Shutter button again to stop recording. Heads Up: The remote’s status light will blink red to show that recording is in progress. PRO TIP: If your camera’s been off for less than 8 hours, you can press the remote’s Shutter button to power on your camera and start recording with QuikCapture. Press and hold the Power button for 8 seconds if you need to reset the remote. Low Battery Indicator An alert on your camera’s display will let you know when the remote’s battery is running low. Replace the battery with a CR2032 coin cell battery. We recommend the GP CR2032 battery for the best performance. Turning Your Shutter Remote Off Press and hold the remote’s Power button for 3 seconds to turn it off. It will also turn off your GoPro if it’s connected. Attaching the Shutter Remote to the Extension Pole Use the remote’s straps to attach it to the extension pole. 1. Wrap the remote’s strap around the grip and thread the end through the loop on the other side of the remote. 2. Fold the strap back on itself and use the hook and loop fasteners to secure the strap. Mounting Your Camera to the Extension Pole ATTACHING A CAMERA MOUNT Attach either the mounting finger adapter or the ball joint adapter to the grip by screwing it clockwise onto the grip’s 1/4-20 mount. Heads Up: You can also attach your camera directly to the 1/4-20 mount. USING THE FINGER ADAPTER Interlace the mounting fingers of your GoPro with the mounting fingers on the mounting finger adapter and secure it with a thumb screw USING THE BALL JOINT ADAPTER 1. Interlace the mounting fingers of your GoPro with the mounting fingers on a standard GoPro mounting buckle (not included) and secure it with a thumb screw. Mounting Your Camera to the Extension Pole 2. Flip up the plug on the mounting buckle and slide the mounting buckle into the mounting base of the ball joint adapter until it clicks into place. Press the plug back down until it sits flush with the base. 3. Flip open the lever on the ball joint adapter to adjust your capture angle. NOTE: Be sure the lever is unlocked when adjusting your camera’s position. Rotating the ball joint with the lever locked could damage the mount. 4. Close the lever to lock in your camera’s position. Tighten or loosen the lever as needed. PRO TIP: Use a screwdriver to tighten the screw on the opposite side of the lever to more securely lock the ball joint in place if necessary. The extension pole can be extended all the way to 48in (122cm) and collapsed down to 10in (25cm). PRO TIP: The extension pole and remote are both waterproof, but the remote will not work under water. Using the Extension Pole Attach the wrist strap extension to the remote’s strap to create a convenient wearable remote. Make sure that the hook patches on both straps are facing the same direction when connecting the straps. Using the Wrist Strap Extension

Important Product & Safety Instructions English Français Deutsch Italiano Español (La) Español (Es) Português Nederlands Suomi Polski Русский Srpski Svenska Українська 中文简体 中文繁體 日本語 한국어 8. Only use attachments/accessories specified by the manufacturer. 9. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Abide by all local laws when using your GoPro and related mounts and accessories, including all privacy laws, which may restrict recording in certain areas. LIFETIME WARRANTY – Extension Pole: GoPro warrants this extension pole (non-electrical GoPro mounts and accessories) under a LIFETIME WARRANTY against defects in materials and workmanship for the lifetime of the product for the benefit of the first purchaser or gift recipient. Products found to be defective will be repaired or replaced at GoPro’s discretion. GoPro reserves the right to make all determinations under this warranty. Products failing due to normal wear and tear, abuse or natural breakdown of materials over extended use and time may be repaired or replaced for a fee. For product support please visit gopro.com/help. LIMITED LIFETIME WARRANTY – Waterproof Shutter Remote: GoPro warrants this remote control for its useful life (not to exceed two year for products with electrical or electronic components) against deficiencies in material and workmanship. This LIMITED LIFETIME WARRANTY does not cover products that are improperly used, abused, altered or repaired. Products found to be defective within the warranty period will be repaired or replaced at GoPro’s discretion. GoPro reserves the right to make all determinations under this warranty. Products failing due to normal wear and tear, abuse or natural breakdown of materials over extended use and time may be repaired or replaced for a fee. For product support please visit gopro.com/help. ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THIS WARRANTY. GOPRO DISCLAIMS ALL OTHER EXPRESSED OR IMPLIED WARRANTIES OR CONDITIONS. TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL GOPRO BE LIABLE FOR ANY LOSS OF REVENUE OR PROFIT, OR FOR ANY SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, HOWEVER CAUSED, ARISING OUT OF OR RELATED TO THE USE OF OR INOPERABILITY OF THE PRODUCT, EVEN IF GOPRO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL GOPRO’S LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. This Lifetime Warranty and Limited Lifetime Warranty give you specific legal rights, and you also may have other rights that vary from state to state or country to country. Some places do not allow limitations on implied warranties or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. For Lifetime Warranty or Limited Lifetime Warranty evaluation please visit www.gopro.com/help for a return authorization before shipping your product to GoPro. For warranty evaluation, your product must be accompanied by an explanation and receipt. All shipping for warranty evaluation must be pre-paid and insured. GoPro cannot be liable for lost in-bound packages. Damage not covered under the Lifetime Warranty or Limited Lifetime Warranty may be repaired or replaced for a reasonable rate and a fee will be charged. Warranty void where prohibited. European Union Consumers: GoPro grants for a period of two (2) years from the original date of purchase of the relevant GoPro product and free of charge a limited manufacturer’s guarantee to the end customer. This shall not limit any consumer rights which you have under consumer law; instead, it grants you additional rights. The guarantee is governed by the following terms and conditions. GoPro guarantees that for a period of two (2) years year from the original date of purchase, your GoPro product will be free from defects in materials and workmanship under normal use and provided it has been used in accordance with the instructions in the relevant GoPro user manual (gopro.com/help). In the event of a defect, please contact GoPro Customer Support (gopro. com/help) for assistance and be prepared to present the original purchase receipt. GoPro’s sole obligation under this guarantee will be, at its option, to repair or replace the defective product. This guarantee does not apply to products damaged by misuse, accident, or normal wear and tear. This guarantee does also not apply to products damaged as a result of repair works not performed by GoPro or an authorized GoPro dealer. Due to possible user resealing error or disassembly, GoPro products used in combination with water-proof housings are not guaranteed against water leakage or other water damage including any damage resulting from it. IMPORTANT PRODUCT AND SAFETY INSTRUCTIONS (ENGLISH) Exercise caution when using your GoPro camera, extension pole, and remote control as part of your active lifestyle. Always be aware of your surroundings to avoid injury to yourself and others. Observe the following precautions to avoid a battery fire: •Do not drop, disassemble, open, crush, bend, deform, puncture, shred, microwave, incinerate or paint the GoPro remote control. •Do not insert foreign objects. •Do not use the remote control if it has been damaged—for example, if cracked, punctured or harmed by water •Disassembling or puncturing the battery (whether integrated or removable) can cause a fire. •Do not dry the remote control with an external heat source such as a microwave oven or hair dryer. •In the event of a battery leaking, do not allow the liquid to come in contact with the skin or eyes. •If contact has been made, wash the affected area with copious amounts of water and seek medical advice. •Do not store…

Text truncated - open the document above for the full version.

GoPro, Inc., 3025 Clearview Way, San Mateo, CA 94402 | GoPro GmbH, Baierbrunner Str. 15, Bldg. D, 81379 Munich, Germany | gopro.com Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: August 15, 2023 Subject: Certifications concerning “covered” equipment pursuant to Part 2.911(d)(5)(i) and (ii) To whom it may concern, GoPro, Inc. certifies that the equipment FCC ID: CNFACCH1 for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. GoPro, Inc. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Name: Michelle Tsai Email: [email protected]

GoPro, Inc., 3025 Clearview Way, San Mateo, CA 94402 | GoPro GmbH, Baierbrunner Str. 15, Bldg. D, 81379 Munich, Germany | gopro.com Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: August 15, 2023 Subject: Certifications concerning “covered” equipment pursuant to Part 2.911(d)(5)(i) and (ii) To whom it may concern, GoPro, Inc. certifies that the equipment FCC ID: CNFACCH1 for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. GoPro, Inc. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Name: Michelle Tsai Email: [email protected]

GoPro, Inc., 3025 Clearview Way, San Mateo, CA 94402 | GoPro GmbH, Baierbrunner Str. 15, Bldg. D, 81379 Munich, Germany | gopro.com Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: August 15, 2023 Ref: Attestation Statements Part 2.911(d)(7) Filing Grantee Code: CNF GoPro, Inc. certifies that, as of the date of the filing of the application, we designate ourselves as the U.S. agent for service of process. Designated U.S. Agent Information: FRN: 0021369186 Name: GoPro, Inc. Address: 3025 Clearview Way, San Mateo, California, United States 94402 Contact Person: Michelle Tsai Tel.: +16503327600 Email: [email protected] Sincerely, Name: Michelle Tsai Email: [email protected]

GoPro, Inc., 3025 Clearview Way, San Mateo, CA 94402 | GoPro GmbH, Baierbrunner Str. 15, Bldg. D, 81379 Munich, Germany | gopro.com Federal Communications Commission Authorization and Evaluation Division Date: August 15, 2023 Re: Long-Term Confidentiality Request regarding application for certification of FCC ID: CNFACCH1 To Whom It May Concern, Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request permanent confidential treatment of information accompanying this application as outlined below: • Schematics • Block Diagram • Parts List • Operation Description • Tune up Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Name: Michelle Tsai Email: [email protected]

GoPro, Inc., 3025 Clearview Way, San Mateo, CA 94402 | GoPro GmbH, Baierbrunner Str. 15, Bldg. D, 81379 Munich, Germany | gopro.com Date: August 15, 2023 Power of Attorney To whom it may concern, Please be notified that I, Michelle Tsai, have designated Jim Tsai in Sporton International Inc. as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Jim Tsai in Sporton International Inc., on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We further certify that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C 862. This authorization is limited to the product of as following: FCC ID: CNFACCH1 If you have any acknowledgement and response, please send it to Sporton International Inc. directly. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, Name: Michelle Tsai Email: [email protected]

GoPro, Inc., 3025 Clearview Way, San Mateo, CA 94402 | GoPro GmbH, Baierbrunner Str. 15, Bldg. D, 81379 Munich, Germany | gopro.com Federal Communications Commission Authorization and Evaluation Division Date: August 15, 2023 Re: Short-Term Confidentiality Request regarding application for certification of FCC ID: CNFACCH1 To Whom It May Concern, Pursuant to sections 0.457 and 0.459 of CFR 47, Public Notice DA 04-1705 of the Commission’s policy and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 180 days: • External Photos • Internal Photos • Test set-up photos • Users Manual The application contains technical information, which GoPro, Inc. deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the marketplace. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Name: Michelle Tsai Email: [email protected]

PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 1 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 1. External Photograph of EUT Brand Name: GoPro / Model Name: ACCH1 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 2 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 3 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 4 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 5 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 6 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 720510 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 7 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 2. Photograph of Accessory Brand Name: GoPro / Model Name: ACCH1 Specification of Accessory Lithium Coin-cell battery Brand Name GP Model Name CR2032 Strap Brand Name GoPro Model Name 480-27499-000 Extension Pole Brand Name GoPro Model Name 230-30917-000 Remark: For accessories equipped with this EUT, please refer to the following photos. PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 8 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 720510 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 9 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 Lithium Coin-cell battery PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 10 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 11 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 Strap PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 12 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 Extension Pole PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 13 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 14 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01

GoPro, Inc., 3025 Clearview Way, San Mateo, CA 94402 | GoPro GmbH, Baierbrunner Str. 15, Bldg. D, 81379 Munich, Germany | gopro.com Rev. D Cert Markings and Placement Model: ACCH1 | FCC ID: CNFACCH1 | IC: 10193A-ACCH1 BODY SIDE HOUSING UNDER BATT BATT DOOR (OUTSIDE) BATT DOOR (INSIDE)

PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 15 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 3. Internal Photograph of EUT Brand Name: GoPro / Model Name: ACCH1 720510 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 16 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 17 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 18 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 19 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 20 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 21 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 22 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP321103 TEL : 886-3-327-3456 Page Number : 23 of 23 FAX : 886-3-328-4978 Issue Date : Aug. 14, 2023 Report Version : 01 ─────THE END──── 720510 Bluetooth Antenna

SPORTON INTERNATIONAL INC. Page Number : 1 of 4 TEL : 886-3-327-3456 Report Issued Date : Aug. 25, 2023 FAX : 886-3-328-4978 Report Version : Rev. 02 FCC ID : CNFACCH1 RF Exposure Evaluation Report Report No. : FA321103 RF Exposure Evaluation Report FCC ID : CNFACCH1 Equipment : Remote Control Brand Name : GoPro Model Name : ACCH1 Applicant : GoPro, Inc. 3025 Clearview Way San Mateo, CA 94402 United States of America Manufacturer : GoPro, Inc. 3025 Clearview Way San Mateo, CA 94402 United States of America Standard : 47 CFR Part 2.1093 We, SPORTON INTERNATIONAL INC has been evaluated this product in accordance with 47 CFR Part 2.1093 and it complies with applicable limit. Sporton Lab is accredited to ISO 17025 by Taiwan Accreditation Foundation (TAF code: 1190) and the FCC designation No. TW1190 under the FCC 2.948(e) by Mutual Recognition Agreement (MRA) in FCC evaluation. The results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. Laboratory, the test report shall not be reproduced except in full. SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City, Taiwan (R.O.C.) Approved by: Cona Huang / Deputy Manager SPORTON INTERNATIONAL INC. Page Number : 2 of 4 TEL : 886-3-327-3456 Report Issued Date : Aug. 25, 2023 FAX : 886-3-328-4978 Report Version : Rev. 02 FCC ID : CNFACCH1 RF Exposure Evaluation Report Report No. : FA321103 Table of Contents 1. General Information ........................................................................................................................... 3 1.1 Description of Device Under Test (DUT) ........................................................................................... 3 2. Maximum RF output power among production units ......................................................................... 3 3. RF Exposure Evaluation .................................................................................................................... 4 Revision History REPORT NO. VERSION DESCRIPTION ISSUED DATE FA321103 Rev. 01 Initial issue of report Aug. 04, 2023 FA321103 Rev. 02 Update section 3 Aug. 25, 2023 SPORTON INTERNATIONAL INC. Page Number : 3 of 4 TEL : 886-3-327-3456 Report Issued Date : Aug. 25, 2023 FAX : 886-3-328-4978 Report Version : Rev. 02 FCC ID : CNFACCH1 RF Exposure Evaluation Report Report No. : FA321103 1. General Information 1.1 Description of Device Under Test (DUT) Product Feature & Specification DUT Type Remote Control Brand Name GoPro Model Name ACCH1 FCC ID CNFACCH1 Wireless Technology and Frequency Range Bluetooth: 2400 MHz ~ 2483.5 MHz Mode Bluetooth LE Antenna Type PIFA Antenna 2. Maximum RF output power among production units Bluetooth Mode Channel Frequency (MHz) Tune-Up Limit LE 1Mbps 0 2402 2.71 19 2440 2.47 39 2480 2.07 SPORTON INTERNATIONAL INC. Page Number : 4 of 4 TEL : 886-3-327-3456 Report Issued Date : Aug. 25, 2023 FAX : 886-3-328-4978 Report Version : Rev. 02 FCC ID : CNFACCH1 RF Exposure Evaluation Report Report No. : FA321103 3. RF Exposure Evaluation Bluetooth Max Power (dBm) mW Separation Distance (mm) Frequency (GHz) Exclusion Thresholds 2.71 1.87 5 2.48 0.6 Note: 1. Per KDB 447498 D01v06 the 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR  f(GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation  The result is rounded to one decimal place for comparison Conclusion: Per KDB 447498 D01v06, when the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. The test exclusion threshold is 0.6 which is <= 3, SAR testing is not required.

*Follow PCBA, no P/N for ANT itself Page 1 of 4 LUXSHAREICT Model Antenna SPECIFICATION Antenna Manufacturer Name LUXSHAREICT Address No.158 Jinchang Road, Kunshan, Suzhou, Jiangsu, China Model： ACCH1 P/N: N/A* Test DATE 2023-5-30 DATASHEET REVISION 01 Test Engineer: Jindiao Pu *Follow PCBA, no P/N for ANT itself Page 2 of 4 LUXSHAREICT Description of Antenna Frequency Range 2402-2480MHz Impedance 1.5nH Antenna type PIFA Manufacturing Process PCB layout Antenna Peak Gain: Freq [MHz] Original Matching Improving Matching Original Matching(Add Arm) Improving Matching(Add Arm) Original Matching(Add Rod) Improving Matching(Add Rod) Eff [dB] Gain [dB] Eff [dB] Gain [dB] Eff[dB] Gain [dB] Eff [dB] Gain [dB] Eff [dB] Gain [dB] Eff [dB] Gain [dB] 2402 -8.75 -5.61 - 7.27 -3.46 -10.13 -6.56 - 8.99 -3.99 -6.28 -2.83 -6.63 -0.59 2440 -9.04 -5.62 - 7.46 -3.98 -9.88 -7.08 - 9.30 -4.08 -6.47 -2.32 -7.05 -1.22 2480 -8.96 -5.08 - 7.67 -4.25 -9.57 -6.92 - 9.41 -3.91 -6.03 -1.77 -6.94 -1.41 Antenna Pattern: (Both 2D or 3D is acceptable) Improving Matching Improving Matching(Add Arm) Improving Matching(Add Rod) 2402 2402 2402 2440 2440 2440 2480 2480 2480 *Follow PCBA, no P/N for ANT itself Page 3 of 4 LUXSHAREICT Antenna Locatio n see test photos *Follow PCBA, no P/N for ANT itself Page 4 of 4 LUXSHAREICT Test Environment, list of calibrated test equipment Test Equipment: CMW500 Test Environment: GTS Rayzone2800 Last Calibration date: 2022/11/30 Next Calibration date: 2023/11/30

TEL : 886-3-327-0868 Page Number : 1 of 19 FAX : 886-3-327-0855 Issue Date : Aug. 09, 2023 Report Template No.: BU5-FR15CBT4.0 Version 2.4 Report Version : 01 FCC RADIO TEST REPORT Report No. : FR321103 FCC RADIO TEST REPORT FCC ID : CNFACCH1 Equipment : Remote Control Brand Name : GoPro Model Name : ACCH1 Applicant : GoPro, Inc. 3025 Clearview Way San Mateo, CA 94402 United States of America Manufacturer : GoPro, Inc. 3025 Clearview Way San Mateo, CA 94402 United States of America Standard : FCC Part 15 Subpart C §15.247 The product was received on Jun. 26, 2023 and testing was performed from Jun. 30, 2023 to Jul. 06, 2023. We, Sporton International Inc. Wensan Laboratory, would like to declare that the tested sample has been evaluated in accordance with the test procedures and has been in compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval from Sporton International Inc. Wensan Laboratory, the test report shall not be reproduced except in full. Approved by: Louis Wu Sporton International Inc. Wensan Laboratory No.58, Aly. 75, Ln. 564, Wenhua 3rd, Rd., Guishan Dist., Taoyuan City 333010, Taiwan (R.O.C.) TEL : 886-3-327-0868 Page Number : 2 of 19 FAX : 886-3-327-0855 Issue Date : Aug. 09, 2023 Report Template No.: BU5-FR15CBT4.0 Version 2.4 Report Version : 01 FCC RADIO TEST REPORT Report No. : FR321103 Table of Contents History of this test report ................................................................................................................................. 3 Summary of Test Result................................................................................................................................... 4 1 General Description ................................................................................................................................... 5 1.1 Product Feature of Equipment Under Test ........................................................................................ 5 1.2 Modification of EUT ........................................................................................................................... 5 1.3 Testing Location ................................................................................................................................ 5 1.4 Applicable Standards ......................................................................................................................... 5 2 Test Configuration of Equipment Under Test ......................................................................................... 6 2.1 Carrier Frequency Channel ............................................................................................................... 6 2.2 Test Mode .......................................................................................................................................... 7 2.3 Connection Diagram of Test System ................................................................................................. 7 2.4 Support Unit used in test configuration and system .......................................................................... 8 2.5…

Text truncated - open the document above for the full version.