CNFAMFR1Camera

GoPro, Inc., 3025 Clearview Way, San Mateo, CA 94402 | GoPro GmbH, Baierbrunner Str. 15, Bldg. D, 81379 Munich, Germany | gopro.com Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: March 7, 2024 Subject: Certifications concerning “covered” equipment pursuant to Part 2.911(d)(5)(i) and (ii) To whom it may concern, GoPro, Inc. certifies that the equipment FCC ID: CNFAMFR1 for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. GoPro, Inc. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Name: Michelle Tsai Email: [email protected]

GoPro, Inc., 3025 Clearview Way, San Mateo, CA 94402 | GoPro GmbH, Baierbrunner Str. 15, Bldg. D, 81379 Munich, Germany | gopro.com Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: March 21, 2024 Subject: Certification designating a U.S. agent for service of process pursuant to Part 2.911(d)(7) To whom it may concern, GoPro, Inc., Grantee Code: CNF (“the applicant”) as required by section 2.911(d)(7), will also serve as the agent for service of process for the above referenced FCC Grantee Code. The service of process includes, but is not limited to, delivery of any correspondence, notices, orders, decisions, and requirements of administrative, legal, or judicial process related to Commission proceedings. The applicant acknowledges that they will maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges their responsibility to inform the FCC whenever the following agent information changes. Designated U.S. Agent Information: FRN: 0021369186 Name: GoPro, Inc. Address: 3025 Clearview Way, San Mateo, California, United States 94402 Contact Person: Michelle Tsai Tel.: +16503327600 Email: [email protected] Sincerely, Name: Michelle Tsai Email: [email protected]

GoPro, Inc., 3025 Clearview Way, San Mateo, CA 94402 | GoPro GmbH, Baierbrunner Str. 15, Bldg. D, 81379 Munich, Germany | gopro.com Date: March 7, 2024 Federal Communications Commission Authorization and Evaluation Division Subject: Request for Confidentiality FCC ID: CNFAMFR1 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR §0.457, 0.459), we are requesting the Commission to withhold the following documents from public disclosure indefinitely. • Schematic Diagram • Block Diagram • Part List • Operational Description • Tune-up Procedure Above mentioned documents contain detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission's policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we are requesting the Commission to withhold the following documents for 180 days after the grant of equipment authorization is issued: • External Photos • Internal Photos • Test Setup Photos • User Manual It is our understanding that all measurement test reports, FCC ID label format cannot be granted as confidential documents and those will be available for public review once the grant of equipment authorization is issued. Best Regards, Name: Michelle Tsai Email: [email protected]

GoPro, Inc., 3025 Clearview Way, San Mateo, CA 94402 | GoPro GmbH, Baierbrunner Str. 15, Bldg. D, 81379 Munich, Germany | gopro.com Date: March 7, 2024 Power of Attorney To whom it may concern, GoPro, Inc. hereby authorize Sporton International Inc. to act on our behalf in all matters relating to applications for FCC equipment authorization, including the signing of all documents relating to these matters. Any and all acts carried out by Sporton International Inc. on our behalf shall have the same effect as acts of our own. We further certify that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C 862. This authorization is limited to the product of as following: FCC ID: CNFAMFR1 This authorization is valid until September 30 th , 2024. Sincerely, Name: Michelle Tsai Email: [email protected]

V2.0 GoPro, Inc., 3025 Clearview Way, San Mateo, CA 94402 | GoPro GmbH, Baierbrunner Str. 15, Bldg. D, 81379 Munich, Germany | gopro.com FCC / ISED Canada e-label Information RMN: AMFR1 e-label image To find Regulatory Information (e-label) in the device: DASHBOARD > “Preference” > “Regulatory” Notes: 1. No special access codes, permissions, or Internet access are required to access to e-label. 2. Users are provided instruction on how to access the e-label in the in-box document. 3. The e-label is pre-programed by the grantee. The user cannot modify the e-label information. 4. FCC ID will be placed on product packaging sleeves.

TEL : 886-3-327-3456 Page 1 of 24 FAX : 886-3-328-4978 Issued Date : Mar. 08, 2024 Template version: 240125 FCC SAR TEST REPORT Report No. : FA3D2932 FCC SAR TEST REPORT FCC ID : CNFAMFR1 Equipment : Camera Brand Name : GoPro Model Name : AMFR1 Applicant : GoPro, Inc. 3025 Clearview Way San Mateo, CA 94402 United States of America Manufacturer : GoPro, Inc. 3025 Clearview Way San Mateo, CA 94402 United States of America Standard : FCC 47 CFR Part 2 (2.1093) The product was received on Feb. 16, 2024 and testing was started from Feb. 16, 2024 and completed on Feb. 17, 2024. We, SPORTON INTERNATIONAL INC., would like to declare that the tested sample provide by manufacturer and the test data has been evaluated in accordance with the test procedures given in 47 CFR Part 2.1093 and FCC KDB and has been pass the FCC requirement. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. Laboratory, the test report shall not be reproduced except in full. Sporton International Inc. Wensan Laboratory No.58, Aly. 75, Ln. 564, Wenhua 3rd, Rd., Guishan Dist., Taoyuan City 333010, Taiwan Approved by: Cona Huang / Deputy Manager TEL : 886-3-327-3456 Page 2 of 24 FAX : 886-3-328-4978 Issued Date : Mar. 08, 2024 Template version: 240125 FCC SAR TEST REPORT Report No. : FA3D2932 Table of Contents 1. Statement of Compliance ............................................................................................................................................. 4 2. Guidance Applied .......................................................................................................................................................... 4 3. Equipment Under Test (EUT) Information ................................................................................................................... 5 3.1 General Information ............................................................................................................................................... 5 4. RF Exposure Limits....................................................................................................................................................... 6 4.1 Uncontrolled Environment ...................................................................................................................................... 6 4.2 Controlled Environment .......................................................................................................................................... 6 5. Specific Absorption Rate (SAR) ................................................................................................................................... 7 5.1 Introduction ............................................................................................................................................................ 7 5.2 SAR Definition ........................................................................................................................................................ 7 6. System Description and Setup .................................................................................................................................... 8 6.1 Test Site Location ................................................................................................................................................... 8 6.2 E-Field Probe ......................................................................................................................................................... 9 6.3 Data Acquisition Electronics (DAE) ........................................................................................................................ 9 6.4 Phantom ................................................................................................................................................................10 6.5 Device Holder........................................................................................................................................................ 11 7. Measurement Procedures ...........................................................................................................................................12 7.1 Spatial Peak SAR Evaluation ................................................................................................................................12 7.2 Power Reference Measurement............................................................................................................................13 7.3 Area Scan .............................................................................................................................................................13 7.4 Zoom Scan ............................................................................................................................................................14 7.5 Volume Scan Procedures ......................................................................................................................................14 7.6 Power Drift Monitoring ...........................................................................................................................................14 8. Test Equipment List .....................................................................................................................................................15 9. System Verification ......................................................................................................................................................16 9.1 Tissue Verification .................................................................................................................................................16 9.2 System Performance Check Results .....................................................................................................................16 10. WiFi/Bluetooth Output Power (Unit: dBm) .…

Text truncated - open the document above for the full version.

Date: 2024-02-16 System Check_Head_2450MHz DUT: D2450V2 - SN929 Communication System: CW; Frequency: 2450.000 MHz; Duty Cycle: 1:1 Medium: HSL_2450_240216 Medium parameters used: f= 2450.000 MHz; σ= 1.80 S/m; ε r = 39.7 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY6 Configuration: - Probe: EX3DV4 - SN7625; ConvF(7.67, 7.67, 7.67); Calibrated: 2023-12-14 - Sensor-Surface: 1.4 mm - Electronics: DAE4 Sn1694; Calibrated: 2023-11-17 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2055; Section: Flat - Measurement Software: 16.2.4.2524 - UID: CW Pin=17.0dBm/Area Scan (40.0 mm x 80.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 2.47 W/kg; SAR (10g) = 1.14 W/kg; Pin=17.0dBm/Zoom Scan (30.0 mm x 30.0 mm x 30.0 mm): Measurement Grid: 5.0 mm x 5.0 mm x 1.5 mm Power Drift = 0.00 dB SAR (1g) = 2.44 W/kg; SAR (8g) = 1.27 W/kg; SAR (10g) = 1.15 W/kg Smallest distance from peaks to all points 3 dB below = 9.0 mm Ratio of SAR at M2 to SAR at M1 = 82.2 % Date: 2024-02-17 System Check_Head_5250MHz DUT: D5GHzV2 - SN1171 Communication System: CW; Frequency: 5250.000 MHz; Duty Cycle: 1:1 Medium: HSL_5G_240217 Medium parameters used: f= 5250.000 MHz; σ= 4.63 S/m; ε r = 36.9 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY6 Configuration: - Probe: EX3DV4 - SN7625; ConvF(5.48, 5.48, 5.48); Calibrated: 2023-12-14 - Sensor-Surface: 1.4 mm - Electronics: DAE4 Sn1694; Calibrated: 2023-11-17 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2055; Section: Flat - Measurement Software: 16.2.4.2524 - UID: CW Pin=17.0dBm/Area Scan (40.0 mm x 80.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 3.54 W/kg; SAR (10g) = 1.01 W/kg; Pin=17.0dBm/Zoom Scan (22.0 mm x 22.0 mm x 22.0 mm): Measurement Grid: 4.0 mm x 4.0 mm x 1.4 mm Power Drift = 0.01 dB SAR (1g) = 3.81 W/kg; SAR (8g) = 1.28 W/kg; SAR (10g) = 1.10 W/kg Smallest distance from peaks to all points 3 dB below = 7.2 mm Ratio of SAR at M2 to SAR at M1 = 64.4 % Date: 2024-02-17 System Check_Head_5600MHz DUT: D5GHzV2 - SN1171 Communication System: CW; Frequency: 5600.000 MHz; Duty Cycle: 1:1 Medium: HSL_5G_240217 Medium parameters used: f= 5600.000 MHz; σ= 4.97 S/m; ε r = 36.4 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY6 Configuration: - Probe: EX3DV4 - SN7625; ConvF(4.87, 4.87, 4.87); Calibrated: 2023-12-14 - Sensor-Surface: 1.4 mm - Electronics: DAE4 Sn1694; Calibrated: 2023-11-17 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2055; Section: Flat - Measurement Software: 16.2.4.2524 - UID: CW Pin=17.0dBm/Area Scan (40.0 mm x 80.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 3.97 W/kg; SAR (10g) = 1.13 W/kg; Pin=17.0dBm/Zoom Scan (22.0 mm x 22.0 mm x 22.0 mm): Measurement Grid: 4.0 mm x 4.0 mm x 1.4 mm Power Drift = 0.05 dB SAR (1g) = 4.25 W/kg; SAR (8g) = 1.42 W/kg; SAR (10g) = 1.22 W/kg Smallest distance from peaks to all points 3 dB below = 7.2 mm Ratio of SAR at M2 to SAR at M1 = 61.0 % Date: 2024-02-17 System Check_Head_5750MHz DUT: D5GHzV2 - SN1171 Communication System: CW; Frequency: 5750.000 MHz; Duty Cycle: 1:1 Medium: HSL_5G_240217 Medium parameters used: f= 5750.000 MHz; σ= 5.12 S/m; ε r = 36.3 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY6 Configuration: - Probe: EX3DV4 - SN7625; ConvF(4.96, 4.96, 4.96); Calibrated: 2023-12-14 - Sensor-Surface: 1.4 mm - Electronics: DAE4 Sn1694; Calibrated: 2023-11-17 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2055; Section: Flat - Measurement Software: 16.2.4.2524 - UID: CW Pin=17.0dBm/Area Scan (40.0 mm x 80.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 3.43 W/kg; SAR (10g) = 0.964 W/kg; Pin=17.0dBm/Zoom Scan (22.0 mm x 22.0 mm x 22.0 mm): Measurement Grid: 4.0 mm x 4.0 mm x 1.4 mm Power Drift = 0.02 dB SAR (1g) = 3.72 W/kg; SAR (8g) = 1.23 W/kg; SAR (10g) = 1.06 W/kg Smallest distance from peaks to all points 3 dB below = 7.2 mm Ratio of SAR at M2 to SAR at M1 = 59.3 %

Communication System: IEEE 802.11b ; Frequency: 2437.000 MHz; Duty Cycle: 1:1.009 Medium: HSL_2450_240216 Medium parameters used: f= 2437.000 MHz; σ= 1.80 S/m; ε r = 39.8 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY6 Configuration: - Probe: EX3DV4 - SN7625; ConvF(7.67, 7.67, 7.67); Calibrated: 2023-12-14 - Sensor-Surface: 1.4 mm - Electronics: DAE4 Sn1694; Calibrated: 2023-11-17 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2055; Section: Flat - Measurement Software: 16.2.4.2524 - UID: WLAN, 10012-CAB Area Scan (60.0 mm x 100.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 0.259 W/kg; SAR (10g) = 0.122 W/kg; Zoom Scan (30.0 mm x 30.0 mm x 30.0 mm): Measurement Grid: 5.0 mm x 5.0 mm x 1.5 mm Power Drift = 0.05 dB SAR (1g) = 0.252 W/kg; SAR (8g) = 0.131 W/kg; SAR (10g) = 0.119 W/kg Smallest distance from peaks to all points 3 dB below = 9.9 mm Ratio of SAR at M2 to SAR at M1 = 79.0 % Date: 2024-02-16 #01_WLAN2.4GHz_802.11b 1Mbps_Top Side_10mm_Ch6 Communication System: IEEE 802.11a; Frequency: 5300.000 MHz; Duty Cycle: 1:1.073 Medium: HSL_5G_240217 Medium parameters used: f= 5300.000 MHz; σ= 4.67 S/m; ε r = 36.8 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY6 Configuration: - Probe: EX3DV4 - SN7625; ConvF(5.48, 5.48, 5.48); Calibrated: 2023-12-14 - Sensor-Surface: 1.4 mm - Electronics: DAE4 Sn1694; Calibrated: 2023-11-17 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2055; Section: Flat - Measurement Software: 16.2.4.2524 - UID: WLAN, 10062-CAE Area Scan (60.0 mm x 100.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 0.349 W/kg; SAR (10g) = 0.119 W/kg; Zoom Scan (22.0 mm x 22.0 mm x 22.0 mm): Measurement Grid: 4.0 mm x 4.0 mm x 1.4 mm Power Drift = 0.00 dB SAR (1g) = 0.361 W/kg; SAR (8g) = 0.128 W/kg; SAR (10g) = 0.111 W/kg Smallest distance from peaks to all points 3 dB below = 7.4 mm Ratio of SAR at M2 to SAR at M1 = 60.6 % Date: 2024-02-17 #02_WLAN5GHz_802.11a 6Mbps_Top Side_10mm_Ch60 Communication System: IEEE 802.11a; Frequency: 5580.000 MHz; Duty Cycle: 1:1.073 Medium: HSL_5G_240217 Medium parameters used: f= 5580.000 MHz; σ= 4.94 S/m; ε r = 36.4 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY6 Configuration: - Probe: EX3DV4 - SN7625; ConvF(4.87, 4.87, 4.87); Calibrated: 2023-12-14 - Sensor-Surface: 1.4 mm - Electronics: DAE4 Sn1694; Calibrated: 2023-11-17 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2055; Section: Flat - Measurement Software: 16.2.4.2524 - UID: WLAN, 10062-CAE Area Scan (60.0 mm x 100.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 0.416 W/kg; SAR (10g) = 0.137 W/kg; Zoom Scan (22.0 mm x 22.0 mm x 22.0 mm): Measurement Grid: 4.0 mm x 4.0 mm x 1.4 mm Power Drift = -0.05 dB SAR (1g) = 0.427 W/kg; SAR (8g) = 0.151 W/kg; SAR (10g) = 0.132 W/kg Smallest distance from peaks to all points 3 dB below = 6.6 mm Ratio of SAR at M2 to SAR at M1 = 58.4 % Date: 2024-02-17 #03_WLAN5GHz_802.11a 6Mbps_Top Side_10mm_Ch116 Communication System: IEEE 802.11ac ; Frequency: 5775.000 MHz; Duty Cycle: 1:1.163 Medium: HSL_5G_240217 Medium parameters used: f= 5775.000 MHz; σ= 5.15 S/m; ε r = 36.2 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY6 Configuration: - Probe: EX3DV4 - SN7625; ConvF(4.96, 4.96, 4.96); Calibrated: 2023-12-14 - Sensor-Surface: 1.4 mm - Electronics: DAE4 Sn1694; Calibrated: 2023-11-17 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2055; Section: Flat - Measurement Software: 16.2.4.2524 - UID: WLAN, 10544-AAD Area Scan (60.0 mm x 100.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 0.133 W/kg; SAR (10g) = 0.039 W/kg; Zoom Scan (22.0 mm x 22.0 mm x 22.0 mm): Measurement Grid: 4.0 mm x 4.0 mm x 1.4 mm Power Drift = 0.15 dB SAR (1g) = 0.122 W/kg; SAR (8g) = 0.036 W/kg; SAR (10g) = 0.031 W/kg Smallest distance from peaks to all points 3 dB below = 5.1 mm Ratio of SAR at M2 to SAR at M1 = 61.0 % Date: 2024-02-17 #04_WLAN5GHz_802.11ac-VHT80 MCS0_Top Side_10mm_Ch155 Communication System: Bluetooth ; Frequency: 2441.000 MHz; Duty Cycle: 1:1.305 Medium: HSL_2450_240216 Medium parameters used: f= 2441.000 MHz; σ= 1.80 S/m; ε r = 39.8 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY6 Configuration: - Probe: EX3DV4 - SN7625; ConvF(7.67, 7.67, 7.67); Calibrated: 2023-12-14 - Sensor-Surface: 1.4 mm - Electronics: DAE4 Sn1694; Calibrated: 2023-11-17 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2055; Section: Flat - Measurement Software: 16.2.4.2524 - UID: Bluetooth, 10032-CAA Area Scan (60.0 mm x 100.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 0.049 W/kg; SAR (10g) = 0.021 W/kg; Zoom Scan (30.0 mm x 30.0 mm x 30.0 mm): Measurement Grid: 5.0 mm x 5.0 mm x 1.5 mm Power Drift = 0.07 dB SAR (1g) = 0.047 W/kg; SAR (8g) = 0.022 W/kg; SAR (10g) = 0.020 W/kg Smallest distance from peaks to all points 3 dB below = 8.1 mm Ratio of SAR at M2 to SAR at M1 = 70.8 % Date: 2024-02-16 #05_Bluetooth_1Mbps_Top Side_10mm_Ch39 Communication System: IEEE 802.11b ; Frequency: 2437.000 MHz; Duty Cycle: 1:1.009 Medium: HSL_2450_240216 Medium parameters used: f= 2437.000 MHz; σ= 1.80 S/m; ε r = 39.8 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY6 Configuration: - Probe: EX3DV4 - SN7625; ConvF(7.67, 7.67, 7.67); Calibrated: 2023-12-14 - Sensor-Surface: 1.4 mm - Electronics: DAE4 Sn1694; Calibrated: 2023-11-17 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2055; Section: Flat - Measurement Software: 16.2.4.2524 - UID: WLAN, 10012-CAB Area Scan (60.0 mm x 100.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 1.26 W/kg; SAR (10g) = 0.518 W/kg; Zoom Scan (30.0 mm x 30.0 mm x 30.0 mm): Measurement Grid: 4.6 mm x 4.6 mm x 1.5 mm Power Drift = 0.01 dB SAR (1g) = 1.20 W/kg; SAR (8g) = 0.519 W/kg; SAR (10g) = 0.463 W/kg Smallest distance from peaks to all points 3 dB below = 6.2 mm Ratio of SAR at M2 to SAR at M1 = 74.1 % Date: 2024-02-16 #06_WLAN2.4GHz_802.11b 1Mbps_Top Side_0mm_Ch6 Communication System: IEEE 802.11a; Frequency: 5300.000 MHz; Duty Cycle: 1:1.073 Medium: HSL_5G_240217 Medium pa…

Text truncated - open the document above for the full version.

SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 D2450V2, serial no. 929 Extended Dipole Calibrations If dipoles are verified in return loss (<-20dB, within 20% of prior calibration), and in impedance (within 5 ohm of prior calibration), the annual calibration is not necessary and the calibration interval can be extended. <Justification of the extended calibration> D2450V2 – serial no. 929 2450MHZ Date of Measurement Return-Loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary Impedance (ohm) Delta (ohm) 11.21.2022 (Cal. Report) -25.5 52.9 4.7 11.20.2023 (extended) -25.9 1.57 52.3 -0.6 4.8 0.1 The return loss is < -20dB, within 20% of prior calibration; the impedance is within 5 ohm of prior calibration. Therefore the verification result should support extended calibration. SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 <Dipole Verification Data> - D2450 V2, serial no. 929 (Data of Measurement : 11.20.2023) 2450MHz - Head SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 D5000V2, serial no. 1171 Extended Dipole Calibrations If dipoles are verified in return loss (<-20dB, within 20% of prior calibration), and in impedance (within 5 ohm of prior calibration), the annual calibration is not necessary and the calibration interval can be extended. <Justification of the extended calibration> D5000V2 – serial no. 1171 5250MHZ Date of Measurement Return-Loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary Impedance (ohm) Delta (ohm) 04.20.2021 (Cal. Report) -20.350.4 -9.7 04.19.2022 (extended) -22.054-8.6449.363 -1.037-7.32052.3795 04.18.2023 (extended) -22.32-9.9547.54 -2.86-6.27233.4277 5600MHZ Date of Measurement Return-Loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary Impedance (ohm) Delta (ohm) 04.20.2021 (Cal. Report) -23.555.5 -4.5 04.19.2022 (extended) -24.852-5.7554.716 -0.784-3.81070.6893 04.18.2023 (extended) -23.2980.86 55.77 0.27 -3.68330.8167 5750MHZ Date of Measurement Return-Loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary Impedance (ohm) Delta (ohm) 04.20.2021 (Cal. Report) -22.155.9 -5.8 04.19.2022 (extended) -24.551-11.0953.48 -2.42-5.9049-0.1049 04.18.2023 (extended) -23.666-7.0952.673 -3.227-6.4029-0.6029 SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 5850MHZ Date of Measurement Return-Loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary Impedance (ohm) Delta (ohm) 04.20.2021 (Cal. Report) -20.5 57.7 -6.6 04.19.2022 (extended) -20.584 -0.41 56.293 -1.407 -6.6585 -0.0585 04.18.2023 (extended) -20.099 1.96 55.011 -2.689 -9.7852 -3.1852 The return loss is < -20dB, within 20% of prior calibration; the impedance is within 5 ohm of prior calibration. Therefore the verification result should support extended calibration. SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 <Dipole Verification Data> - D5000 V2, serial no. 1171 (Data of Measurement : 04.19.2022) 5000 MHz - Head SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 <Dipole Verification Data> - D5000 V2, serial no. 1171 (Data of Measurement : 04.18.2023) 5000 MHz - Head

1 Copyright © by Passive System Alliance | All rights reserved. 2 OUTLINE 1. Antenna Overview 3. Summary 2.1 Antenna Efficiency and Peak Gain 2.2 views of antenna & 2D/3D Radiation Patterns 1.1 Antenna Datasheet 2. Antenna Characteristics 3 Product OC: RFFPA251100NNLB001 Antenna manufacturer: Passive System Alliance Manufacturer Address:No. 11, Keyi St., Zhunan Township, Miaoli County 350402 , Taiwan (R.O.C.) Released Date: 2024-01- 04 Product Name: Wifi FPC Antenna Key Features: Antenna type: FPC Loop Antenna Frequency Band: 2400-2500 MHz ,5150-5850MHz Peak Gain: 2G/1.48dBi, 5G/3.01dBi Efficiency: Up to 43.9 % Compliant 1. Antenna Overview 1.1 Antenna Datasheet 4 Maximum Efficiency at 5200 MHz : 43.97 % 2.1 Antenna Efficiency and Peak Gain Maximum Peak Gain at 5750 MHz : 3.01 dBi WiFi -5G 2. Antenna Characteristics 5 2.2 3D Radiation Patterns 2. Antenna Characteristics 2412 MHz 6 2.2 3D Radiation Patterns 2. Antenna Characteristics 2442 MHz 7 2.2 3D Radiation Patterns 2. Antenna Characteristics 2462 MHz 8 2.2 3D Radiation Patterns 2. Antenna Characteristics 5200 MHz 9 2.2 3D Radiation Patterns 2. Antenna Characteristics 5300 MHz 10 2.2 3D Radiation Patterns 2. Antenna Characteristics 5600 MHz 11 2.3 3D Radiation Patterns 2. Antenna Characteristics 5785 MHz 12 WiFi-2GWiFi-5G-B1WiFi-5G-B2WiFi-5G-B3WiFi-5G-B4 Maximum Efficiency (%) 42.1443.9741.7240.740.97 Maximum Gain (dBi) 1.482.722.262.823.01 •The performance of antennas is shown in table 3. Summary

TEL : 886-3-327-0868 Page Number : 1 of 23 FAX : 886-3-327-0855 Issue Date : Mar. 08, 2024 Report Template No.: BU5-FR15CBT4.0 Version 2.4 Report Version : 01 FCC RADIO TEST REPORT Report No. : FR3D2932B FCC RADIO TEST REPORT FCC ID : CNFAMFR1 Equipment : Camera Brand Name : GoPro Model Name : AMFR1 Applicant : GoPro, Inc. 3025 Clearview Way San Mateo, CA 94402 United States of America Manufacturer : GoPro, Inc. 3025 Clearview Way San Mateo, CA 94402 United States of America Standard : FCC Part 15 Subpart C §15.247 The product was received on Jan. 11, 2024 and testing was performed from Jan. 15, 2024 to Mar. 06, 2024. We, Sporton International Inc. Wensan Laboratory, would like to declare that the tested sample has been evaluated in accordance with the test procedures and has been in compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval from Sporton International Inc. Wensan Laboratory, the test report shall not be reproduced except in full. Approved by: Louis Wu Sporton International Inc. Wensan Laboratory No.58, Aly. 75, Ln. 564, Wenhua 3rd, Rd., Guishan Dist., Taoyuan City 333010, Taiwan (R.O.C.) TEL : 886-3-327-0868 Page Number : 2 of 23 FAX : 886-3-327-0855 Issue Date : Mar. 08, 2024 Report Template No.: BU5-FR15CBT4.0 Version 2.4 Report Version : 01 FCC RADIO TEST REPORT Report No. : FR3D2932B Table of Contents History of this test report ................................................................................................................................. 3 Summary of Test Result................................................................................................................................... 4 1 General Description ................................................................................................................................... 5 1.1 Product Feature of Equipment Under Test ........................................................................................ 5 1.2 Modification of EUT ........................................................................................................................... 5 1.3 Testing Location ................................................................................................................................ 6 1.4 Applicable Standards ......................................................................................................................... 6 2 Test Configuration of Equipment Under Test ......................................................................................... 7 2.1 Carrier Frequency Channel ............................................................................................................... 7 2.2 Test Mode .......................................................................................................................................... 8 2.3 Connection Diagram of Test System ................................................................................................. 9 2.4 Support Unit used in test configuration and system .......................................................................... 9 2.5 EUT Operation Test Setup .............................................................................................................. 10 2.6 Measurement Results Explanation Example ................................................................................... 10 3 Test Result ..........................................................................................................................................…

Text truncated - open the document above for the full version.