CVTRA6222HRemote Controlled Toy (Receiver)

1/12 Radio Control Car NIKKO PRINTED IN MALAYSIA IMPRIME EN MALAISIE IMPRESO EN MALASIA English / Français / Español Owner's Manual Manuel du lutilisateur Manual del Propietario • Recharge the Battery Before You Start to Operate • Recargue la bateria antes de empezar a jugar • Recharger la batterie avant d'allumer ATTENTTION: JOUET ELECTRIQUE Non recommandé pour les enfants de moins de 8 ans. Comme aves tous les appareils électriques, des précaut ons doivent être observées pendant la manipulation et l'emploi pour éviter toute décharge électrique. Entrée: secteur 120 VAC, 60 Hz seulement Sortie: 12VDC 200mA PARENTS ATTENTION Il est recommandé de vérifier périodiquement l'absence de risque potentiel sur ce jouet et tous les accessoires et de réparer o remplacer les pieces potentieliement dangereuses. FEATURES PRECAUCÓN: JUGETE ELÉCTRICO No recomendado para niños de menos de 8 años de edad. AL igual que con todos los productos eléctricos, para evitar un shock eléctrico, se deben observar precauciones especiales al manipular y usar este juguete. Entrada: Solamente 120 VAC, 60 Hz. Salida: 12 VDC, 200mA ATENCIÓN PADRES Se recomienca que este juguete y todos sus accesorios sean examinados periódicamente para tratar de encontrar peligros potenciales provocados por piezas que necesiten ser reparadas o cambiadas. CARACTERISTIQUES CARACTERÍSTICAS 9.6 V KMNA-120125 NMO-300505 NECESIDADES DE PILAS PILE/BATTERIE BATTERY REQUIREMENTS: Vehicle : Ni-Cd battery energy pack (9.6V, 600-650mAh) Transmitter : 1 x 9V(006P)battery Véhicule : Batterie autonome Ni-Cd (9,6V, 600-650mAh)rechargeable Emetteur : 1 pile 006p(9V) Vehiculo : Bateria de pilas do Ni-Cd "energy pack" de (9,6V, 600-650mAh) Transmisor : 1 pila de 9 V (006P) 2-channel full function: Forward, reverse, left/ right turn and stop. Transform action. Rear wheel differential gear. Front & rear suspension. Working headlight. Please read carefully before starting to operate. Keep the display box and the manual for future reference. Warning! Use under the direct supervision of an adult Actual product may vary from illustration of this manual. Lea estas instrucciones detenidamente antes de la utilización. Guardar la caja y el manual para su consulta en el futuro. Precautión! Úselo bajo la supervisión diercta de un adulto. El producto real puede diferir ligeramente de las ilustraciones. Lisez attentivement ce manuel avant de commencer à utiliser le véhicule. Conservez la boîte d'exposition et le manuel pour toute référence ultérieure. Attention! A utiliser sous la supervision directe d’un adulte. La moto contenue dans l'emballage peut ne pas correspondre exactement aux illustrations. ! Toutes fonctions, 2 canaux: marche avant, arrière, virage à gauche/droite et arrèt Transformation. Fonctionnement des phares avant Funciones completas mediante dos canales: Avance, retroceso, giros a la izquierda o derecha y detención Acción de transformación. Faros que se iluminan. 120125 Morph nator ST-39672 English 2 Do not charge Battery Pack immediately after use. Wait until it has cooled before charging. Avoid short circuits. Short circuits will cause overheating, burning of the cords and other damages to the battery Pack and Charger. The Ni-Cd Battery Charger should be used for charging one Battery Pack. Do not use the Charger for charging other type of batteries and battery packs Do not use the Charger as a direct current outlet for other electrical appliances or machines. Make sure that the Battery Pack and Charger are kept out of the hands of infants and small children while charging. Do not charge near fires, where the temperature is extremely high, or where it is wet or damp. The charger will become slightly heated while charging. Allow sufficient free space around the Charger. If the power of the battery pack is weak in spite of proper charging, the batteries may be worn out from repeated use. Replace it with a new Ni-Cd battery pack. Dispose of use Ni-Cd battery packs correctly. Disconnect the supply before making or breaking connections to the battery. Only use batteries or accumulators of the recommended type or a similar type. WARNING AGAINST RECHARGING NON-RECHARGEABLE BATTERIES. Please use this battery charger only for the charge of the rechargeable battery pack. The Ni-Cd battery pack should be charged under the supervision of an adult. CAUTION RECHARGING "WARNING! USE UNDER THE DIRECT SUPERVISION OF AN ADULT." * The newly purchased Ni-Cd pack is not charged. Charge before operating. Household outlet Ni-Cd battery pack OR Charger Household outlet Charger Ni-Cd battery pack 1. Join the connector of the charger to the connector of the Ni-Cd battery pack. 2. Plug the charger into an electrical outlet. 3. Recharge for about 4-5 hours. 4. When the recharging is over, plug out the charger from the electrical outlet and detach the connectors. When playing for the first time after purchase, or after a long interval, the battery power may be weak. Even after recharging, the playing time can be relatively short. The battery will gradually regain power after 2 or 3 repetitions of usage and recharging. TOP VIEWBOTTOM VIEW NAMES OF PARTS 120125 Morph nator Transmitter antenna 3 English Pass the antenna wire through the antenna tube, then insert the tube into the antenna tube holder. If the antenna tube cannot be successfully inserted into the antenna tube holder, try holding the root of the antenna wire with fingers of one hand and extending the wire with fingers of the other hand. 1. HOW TO ATTACH ANTENNA TUBE * Note: Be careful not to pull antenna wire too strong. PREPARATION FOR STARTING OPERATION 2. HOW TO INSTALL TRANSMITTER ANTENNA Place the transmitter antenna into the antenna holder to screw it in clock-wise. Do not extend the antenna when installing. It’s dangerous. If the antenna is not screwed in securely, the vehicle may move erratically. Screw the antenna securely. Antenna wire Antenna tube Antenna tube holder 3. HOW TO INSTALL THE BATTERIES Transmitter…

Text truncated - open the document above for the full version.

FCC ID:CVTRA6222H NO.RA6222 CIRCUIT EXPLANANTION 1) The Radio Frequency inputted through the ANT.,is passed to the Super- regenerative receiver, formed by TR1,where the Action Signal is detected. 2) The Action Signal is decoded in the control IC.,and are sent to each output terminal. 3) TR7,13,14,15,16,17 and 18 form the steering control circuit. (3-1)Right turns. IC.7p.(pin) is turned on,and TR7,13,16 and 17 are tuned on to make a Right turn. (3-2)Left turns. IC.9p is turned on,and TR14,15 and 18 are turned on to make a Left turn. 4) TR6,8,9,22,23,24 and 25 form the driving control circuit. (4-1)Forward drive. IC.15p is turned on,and TR8,22 and 25 are turned on to make a Forward drive. (4-2)Backward drive. IC.14p is turned on, and TR6,9,23 and 24 are turned on to make a Backward drive. 5) TR2,3,4,5,26,27,28 and 29 form the Up-Down action control circuit. (5-1)Up action.(From Down side state) IC.6p is turned on, Then TR3,4,27 and 28 are turned on to make a Up motion. (5-2)Down extend action.(From Up side state.) IC.8p is turned on, Then TR2,5,26 and 29 are turned on to make a Down extend motion.

NO.RA6222 PCB.PARTS LIST 49.860MHz for CVTRA6222H NO.DESCRIPTIONCODEPARTS NAMENOTENO.DESCRIPTIONCODEPARTS NAMENOTE 1I.C.IC1RX6ACTION72R35100K 2TRANSISTORTR12SC380-O73R36100K 3TR22SC1623L6 or equivalent74R37820 1/10w 4TR32SC1623L6 or equivalent75R38820 1/10w 5TR42SC1623L6 or equivalent76R3922 2w 6TR52SC1623L6 or equivalent77R4022 2w 7TR62SC1623L6 or equivalent78R411k 8TR72SC1623L6 or equivalent79R42150k 9TR8MPS8050S or equivalent80R43- 10TR9MPS8050S or equivalent81R460 ohm 11TR10-82CAPACITORC 110p(C) 12TR11-83C 25p(C) 13TR132SC1623L6 or equivalent84C 333p(C) 14TR142SC1623L6 or equivalent85C 4100(E) 15TR15MPS8550S or equivalent86C 54.7(E) 16TR16MPS8550S or equivalent87C 6222(CH) 17TR17MPS8050S or equivalent88C 7103(B,X7R) 18TR18MPS8050S or equivalent89C 8- 19TR222SB1658 or equivalent 90C 9103(B,X7R) 20TR232SB1658 or equivalent 91C10100(E) 21TR242SD2583 or equivalent 92C11100(E) 22TR252SD2583 or equivalent 93C12- 23TR26KTA1663 or equivalent94C13222(B,X7R) 24TR27KTA1663 or equivalent95C14471(B,X7R) 25TR28KTC4375 or equivalent96C15104(C) 26TR29KTC4375 or equivalent97C1633p(C) 27DIODED11N4148WS or equivalent 98C17100(E) 28D20 ohm99C18104(C) 29D30 ohm100C19100(E) 30D41N4148WS or equivalent101C2010(N) 31D51N4148WS or equivalent102C2110(N) 32D61N4148WS or equivalent103C22105(C) 33D71N4148WS or equivalent 104C23105(C) 34D81N4148WS or equivalent 105C24- 35D9-106C25- 36D10-107C27100(E) 37D111N4148WS or equivalent 108C28471(B,X7R) 38D121N4148WS or equivalent 109C29- 39RESISTORR1150K110C30- 40R3820111C31104(C) 41R42.2K112C32104(C) 42R53.3k113INDUCTORL 1- 43R6330114L 2SP 3.3uH 44R7120k115L 3S6.5T 45R82.2K116JUMPERJ 10 ohm 46R9120(1/10W)117J 20 ohm(5mm gilted wire) 47R104.7M118J 30 ohm(30mm gilted wire) 48R112.2K119J 40 ohm 49R124.7M120J 50 ohm 50R131K121J 60 ohm 51R141K122J 70 ohm 52R154.7K123J 80 ohm 53R164.7k124J 90 ohm 54R171k125J100 ohm 55R181k126J110 ohm 56R19100K127J120 ohm 57R20100K128J130 ohm 58R21180 (1/10W) 129J140 ohm(5mm gilted wire) 59R22180 (1/10W) 130J15- 60R2347k131J160 ohm 61R2447K132J170 ohm 62R2510K131EXTRA PARTSEP1Heat sink:H-7 x 2 63R2610K132EP2TP:3*8B(W/spring washer)x4 64R2768(1W)133EP3PCB:NO.RA6222 65R2868(1W)RESISTOR:1608 type chip,1/16W,±5% INDUCTOR:100mA,±10% 66R29120(1/10W)CAPACITOR(C):Ceramic,1608 type chip,50WV,+-10% (T):Tantalum,35WV,±10% 67R3010k (M):Mylar,50WV[No mark=K.rank(±10%),J.rank(±5%)] 68R3110k (E):Electrolytic,16WV,±20% (N):Non pole Electrolytic,16WV,±20% 69R32- 70R3310K 71R3410K NO.RP6403D PCB.PARTS LISTVer.1 27{40}[49]MHz for 1/12 discrete steering type RX.PCB.2003.12.16 SI. NO.DESCRIPTIONCODENormal versionTimer cut off versionRescue TypeNO.DESCRIPTIONCODENormal versionTimer cut off versionRescue Type 1I.C.IC1PS8A1211W51R26100K 2IC2uPA1792uPA179352R271K 3IC3uPA1792uPA179353R281K 4TRANSISTORTR12SC380-O or KTC3879S54R29120(1/10W) 5TR2-MPS8050S or equivalent55R30-4.7K 6TR3-2SA812M5 or equivalent56R31- 7TR4-MPS8050S or equivalent57R32- 8TR5-MPS8050S or equivalent58R33-10K 9TR62SA812M5 or equivalent59R34-10K 10TR72SA812M5 or equivalent60R3510K 11TR82SC1623L6 or equivalent61R3610K 12TR92SC1623L6 or equivalent62R370.2 (5W) 13TR102SC1623L6 or equivalent63R38-10K 14TR112SC1623L6 or equivalent64R39-1K 15TR12MPS8550S or equivalent65R40- 16TR13MPS8550S or equivalent66R45-1K 17TR14MPS8050S or equivalent67R46-470K 18TR15MPS8050S or equivalent68R47-10K 19TR16-MPS8050S or equivalent69R491K 20TR21-2SC1623L6 or equivalent70R501K 21TR22-2SC1623L6 or equivalent71CAPACITORC 11p(C) 22DIODED1-1N4148WS or equivalent1N4148WS or equivalent72C 210p{22p}[5p](C) 23D2-1N4148WS or equivalent1N4148WS or equivalent73C 368p{47p}[33p](C) 24D31N4148WS or equivalent1N4148WS or equivalent74C 4100(E) 25D4-75C 54.7(E) 26D7-1N4148WS or equivalent76C 6332{332}[222](CH) 27D8-1N4148WS or equivalent77C 7103(B,X7R) 28D9-1N4148WS or equivalent78C 9104(C) 29D11-1N4148WS or equivalent79C10100(E) 30D12-1N4148WS or equivalent80C11100(E) 31D131N4148WS or equivalent81C12- 32D141N4148WS or equivalent82C13222(B,X7R) 33RESISTORR1150K83C14471(B,X7R) 34R2-4.7k84C15104(C) 35*R3560{560}[820]85C1633p(C) 36R42.2K86C17- 37R52.2K{3.3K}[1.8K]87C18104(C) 38R633088C19- 39R7100K89C2010(N) 40R82.2K90C22- 41R9120(1/10W)91C23- 42R104.7M92C24-47(E) 43R112.2K93C25-47(E) 44R124.7M94C26105(C) 45R1310K95C27-100(E) 46R1410K96C28471(C) 47R150 ohm97C29105(C) 48R160 ohm98C32104(C) 49R17-33(2W)99C33- 50R18-100C35-105(C) 51R1910K101L 1SP 1uH 52R2010K102INDUCTORL 2SP 3.3uH 53R21100103L 3S11.5T{S6.5T}[S6.5T] 54R22100104JUMPERJ 10 ohm 55R23-4.7K106J 40 ohm(WIRE) 55R25100K107J 60 ohm 108J80 ohm- 109J 90 ohm 110J100 ohm(70mm WIRE) 111J110 ohm 112J120 ohm- 113J13-0 ohm 114J14--0 ohm 115J180 ohm(WIRE) 116EXTRA PARTSEP1PCB:NO.RP6403 RESISTOR:1608 type chip,1/16W,±5% INDUCTOR:100mA,±10% CAPACITOR(C):Ceramic,1608 type chip,50WV,+-10% (T):Tantalum,35WV,±10% (M):Mylar,50WV[No mark=K.rank(±10%),J.rank(±5%)] (E):Electrolytic,16WV,±20% (N):Non pole Electrolytic,16WV,±20%

JAPAN QUALITY ASSURANCE ORGANIZATION 21-25, KINUTA 1-CHOME, SETAGAYA-KU, TOKYO 157-8573 JAPAN PHONE (03) 3416-0111, FAX (03) 3416-9691 JQA File No. : 400-50245 Issue Date : June 27, 2005 Page 1 of 25 EMI TEST REPORT JQA File No. : 400-50245 Model No. : RA6222H Type of Equipment : Radio Controlled Toy (Superregenerative Type) Regulations Applied : CFR 47 FCC Rules and Regulations Part 15 FCC ID : CVTRA6222H Applicant : NIKKO CO., LTD. Address : 1-7-14, Mizumoto, Katsushika-ku, Tokyo 125-0032, Japan Manufacturer : NIKKO ELECTRONICS BHD. Address : Plot 497, Prai Free Trade Zone, Prai Industrial Estate, Prai, Penang, Malaysia. 13600 Received date of EUT : June 22, 2005 Final Judgment : Passed Test results in this report are obtained in use of equipment that is traceable to National Institute of Advanced Industrial Science and Technology (AIST) of Japan and National Institute of Information and Communications Technology (NICT) of Japan. The test results only respond to the tested sample. This report should not be reproduced except in full, without the written approval of JQA EMC Engineering Dept. Testing Div. JQA File No. :400-50245 FCC ID :CVTRA6222H Model No. :RA6222H Issue Date :June 27, 2005 Standard :CFR 47 FCC Rules Part 15 Page 2 of 25 JAPAN QUALITY ASSURANCE ORGANIZATION TABLE OF CONTENTS Page 1 Documentation 1.1 Test Regulation 3 1.2 General Information 3 1.3 Test Condition 4 – 7 1.4 EUT Modifications / Deviation from Standard 8 1.5 Test results / Uncertainty 9 1.6 Summary 10 1.7 Test Configuration / Operation of EUT 11 1.8 EUT Arrangement (Drawings) 12 1.9 Preliminary Test and Test-setup (Drawings) 13 – 16 1.10 EUT Arrangement (Photographs) 17 2 Test Data 2.1 AC Power Line Conducted Emission N/A 2.2 Radiated Emission (Electric Field) 18 – 20 2.3 Antenna Conducted Power N/A 3 Appendix Test instruments List 21 – 25 JQA File No. :400-50245 FCC ID :CVTRA6222H Model No. :RA6222H Issue Date :June 27, 2005 Standard :CFR 47 FCC Rules Part 15 Page 3 of 25 JAPAN QUALITY ASSURANCE ORGANIZATION 1 DOCUMENTATION 1.1 TEST REGULATION FCC Rules and Regulations Part 15 Subpart A and B Superregenerative Receiver Test procedure : AC power line conducted emission, radiated emission and antenna conducted power tests were performed according to the procedures in ANSI C63.4-2003. 1.2 GENERAL INFORMATION 1.2.1 Test facility : 1) Test Facility located at EMC Engineering Dept. Testing Div. : - No.2 and 3 Anechoic Chambers( 3 meters Site ). - Shielded Enclosure. 2) EMC Engineering Dept. Testing Div. is recognized under the National Voluntary Laboratory accreditation Program for satisfactory compliance established in title 15, Part 285 Code of Federal Regulations. NVLAP Lab Code : 200189-0 1.2.2 Description of the Equipment Under Test (EUT) : 1) Type of Equipment : Radio Controlled Toy 2) Product Type : Production 3) Category : Superregenerative Receiver 4) EUT Authorization : Certification 5) FCC ID : CVTRA6222H 6) Trade Name : NIKKO 7) Model No. : RA6222H 8) Tuning Frequency Range : 49.830 MHz – 49.890 MHz 9) Highest Frequency Used in the EUT : - 10) Serial No. : None 11) Date of Manufacture : None 12) Power Rating : 9.6VDC (Battery pack) 13) EUT Grounding : None 1.2.3 Definitions for symbols used in this test report : x - indicates that the listed condition, standard or equipment is applicable for this report. - indicates that the listed condition, standard or equipment is not applicable for this report. JQA File No. :400-50245 FCC ID :CVTRA6222H Model No. :RA6222H Issue Date :June 27, 2005 Standard :CFR 47 FCC Rules Part 15 Page 4 of 25 JAPAN QUALITY ASSURANCE ORGANIZATION 1.3 TEST CONDITION 1.3.1 The measurement of the AC Power Line Conducted Emission - was performed in the following test site. x - was not applicable. Test location : Safety & EMC Center EMC Engineering Dept. Testing Div. 21-25, Kinuta 1-chome, Setagaya-ku, Tokyo 157-8573, Japan - Shielded Enclosure - Anechoic Chamber No. 2 (portable Type) Used test instruments : Type Number of test instruments (Refer to Appendix) Test Receiver N/A Spectrum Analyzer N/A Cable N/A AMN(for EUT) N/A AMN(for Peripheral) N/A Termination N/A JQA File No. :400-50245 FCC ID :CVTRA6222H Model No. :RA6222H Issue Date :June 27, 2005 Standard :CFR 47 FCC Rules Part 15 Page 5 of 25 JAPAN QUALITY ASSURANCE ORGANIZATION 1.3.2 The measurement of the Radiated Emission(30 MHz – 1000 MHz) x - was performed in the following test site. - was not applicable. Test location : Safety & EMC Center EMC Engineering Dept. Testing Div. 21-25, Kinuta 1-chome, Setagaya-ku, Tokyo 157-8573, Japan - Anechoic Chamber No. 2 (3 meters) x - Anechoic Chamber No. 3 (3 meters) Validation of Site Attenuation : 1) Last Confirmed Date :March, 2005 2) Interval :1 year Used test instruments : Type Number of test instruments (Refer to Appendix) Test Receiver TR06 Antenna AN03, AN07, AN09 Cable CA02 RF Amplifier N/A Signal Generator SG05 JQA File No. :400-50245 FCC ID :CVTRA6222H Model No. :RA6222H Issue Date :June 27, 2005 Standard :CFR 47 FCC Rules Part 15 Page 6 of 25 JAPAN QUALITY ASSURANCE ORGANIZATION 1.3.3 The measurement of the Radiated Emission(Above 1000 MHz) - was performed in the following test site. x - was not applicable. Test location : Safety & EMC Center EMC Engineering Dept. Testing Div. 21-25, Kinuta 1-chome, Setagaya-ku, Tokyo 157-8573, Japan - No. 2 site (3 meters) - No. 3 site (3 meters) Validation of Site Attenuation : 1) Last Confirmed Date :March, 2005 2) Interval :1 year Used test instruments : Type Number of test instruments (Refer to Appendix) Test Receiver N/A Spectrum Analyzer N/A Cable N/A Antenna N/A RF Amplifier N/A JQA File No. :400-50245 FCC ID :CVTRA6222H Model No. :RA6222H Issue Date :June 27, 2005 Standard :CFR 47 FCC Rules Part 15 Page 7 of 25 JAPAN QUALITY ASSURANCE ORGANIZATION 1.3.4 The measurement of the Antenna Conducted Power - was performed in the following test site. x - was not applicable. Test location : Safety & EMC Center EMC Engineering Dept. Testing Div…

Text truncated - open the document above for the full version.

JQA File No. :400-50245 FCC ID :CVTRA6222H Model No. :RA6222H Issue Date :June 27, 2005 Standard :CFR 47 FCC Rules Part 15 Page 17 of 25 JAPAN QUALITY ASSURANCE ORGANIZATION 1.10 TEST ARRANGEMENT (PHOTOGRAPHS) PHOTOGRAPHS OF EUT CONFIGURATION FOR RADIATED EMISSIONS MEASUREMENT Photograph present configuration with maximum emission