DCO-BN3-433AExpress GSM2 Remote Control BN3-433A

7 TEST CERTIFICATE FCC INFORMATION This device complies with Part 15 of the FCC Results. Operation is subject to the following two conditions: This Device may not cause harmful interface, and this device must accept any interference received, including interference that may cause undesired operation. Not e: This equipment has been tested and found to comply with the limits for digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures: 1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected. 1.4. Consult the dealer or experienced radio/TV technician for help. WARNING Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. FCC approved GSM module is used in this mobile/fixed application. The ant enna (with required gain in its certification) used for the GSM transmitter must be inst alled to provide a separation dist ance of at least 20 cm from all persons in order to satisfy RF exposure compliance for the final host device.

A A l l p p h h a a A A r r s s e e n n a a l l L L L L C C 104-20 Queens Blvd., office 1B Forest Hills, NY 11375 P: (718) 440 3281 Subject: FCC Confidentiality Request for FCC ID: DCO-BN3-433A To Whom It May Concern: Please accept this letter as an official request to have all Schematics, Bill of Materials, Block Diagrams and Methods of Operation of the DCO-BN3-433A, Express GSM 2 Remote Controller application treated as confidential. This request is made pursuant to 47 CFR Section 0.457(d) of the Commission's Rules, and Section 552(b)(4) of the Freedom of Information Act. The information contained within represents many hours of engineering and design that should remain confidential as to protect our company's intellectual property and investments. Sincerely, Signature: Printed Name: Sergey Medvedev Title: General Manager Company: Alpha Arsenal LLC

22 Figure 7.1 Front View 23 Figure 7.2 Rear View

8 2. PRODUCT LABELING Figure 2.1 FCC ID Label Figure 2.2 Location of Label on the Side of EUT Figure 2.2 FCC ID Label Location FCC ID: DCO-BN3-433A This device complies with part 15 of the FCC Rules. Operating is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Figure 2.1 FCC ID Label FCC Label

24 Figure 7.3 Cover opened_ Inside View 25 Figure 7.4 Component Side 26 Figure 7.5 Foil Side

1 ELECTROMAGNETIC EMISSION COMPLIANCE REPORT of EXPRESS GSM2 Remote Control MODEL: BN3-433A FCC ID: DCO-BN3-433A August 2, 2012 This report concerns (check one): Original grant x Class II change Equipment type: Low Power Intentional Radiator Deferred grant requested per 47 CF 0.457(d)(1)(ii)? yes no x If yes, defer until: (date) Company agrees to notify the Commission by (date) of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? yes no x If no, assumed Part 15, Subpart B for unintentional radiators - the new 47 CFR [10-1-90 Edition] provision. Report prepared for: ALPHA ARSENAL LLC Report prepared by: Advanced Compliance Lab Report number: 0048-120627-01 The test result in this report IS supported and covered by the NVLAP accreditation 6 Randolph Way Hillsborough, NJ 08844 Tel: (908) 927 9288 Fax: (908) 927 0728 Advanced Compliance Laboratory 2 Table of Contents Report Cover Page ..................................................................................................... 1 Table of Contents ....................................................................................................... 2 Figures ........................................................................................................................ 3 1. GENERAL INFORMATION ........................................................................................ 4 1.1 Verification of Compliance .............................................................................................. 4 1.2 Equipment Modifications ................................................................................................. 5 1.3 Product Information ......................................................................................................... 6 DCO-BN3-433A .................................................................................................................... 6 1.4 Test Methodology ............................................................................................................ 6 1.5 Test Facility ..................................................................................................................... 6 1.6 Test Equipment ................................................................................................................ 6 1.7 Statement for the Document Use ...................................................................................... 7 2. PRODUCT LABELING .................................................................................................. 8 3. SYSTEM TEST CONFIGURATION ....................................................................... 9 3.1 Justification...................................................................................................................... 9 3.2 Special Accessories .......................................................................................................... 9 3.3 Configuration of Tested System........................................................................................ 9 4. SYSTEM SCHEMATICS ............................................................................................... 13 5. CONDUCTED EMISSION DATA ............................................................................ 14 5.1 Test Methods and Conditions ........................................................................................... 14 5.2 Test Data ......................................................................................................................... 14 6. RADIATED EMISSION DATA.................................................................................. 17 6.1 Field Strength Calculation ............................................................................................... 17 6.2 Test Methods and Conditions ........................................................................................... 17 6.3 Test Data ......................................................................................................................... 17 6.4 Occupied Bandwidth ........................................................................................................ 19 7. PHOTOS OF TESTED EUT.......................................................................................... 21 3 Figures Figure 2.1 FCC ID Label ........................................................................................... 8 Figure 2.2 Location of Label on Back of the EUT .................................................... 8 Figure 3.1 Radiated Test Setup, Position 1 ............................................................... 10 Figure 3.2 Radiated Test Setup, Position 2 ............................................................... 10 Figure 3.3 Radiated Test Setup, Position 3 ............................................................... 11 Figure 3.4 Conducted Test Setup, Front................................................................... 12 Figure 3.5 Conducted Test Setup, Rear .................................................................... 12 Figure 4.1 EUT Schematics ....................................................................................... 13 Figure 5.1 Line Conducted ........................................................................................ 15 Figure 5.2 Neutral Conducted .................................................................................. 16 Figure 6.1 Bandwidth Plot ........................................................................................ 19 Figure 6.2 Pulse Train Timing .................................................................................. 20 Figure 7.1 Front View ................................................................................................ 21 Figure 7.2 Rear View ................................................................................................. 22 Figure 7.3 Cover Opened_ Ins…

Text truncated - open the document above for the full version.

10 Figure 3.1 Radiated Test Setup, position 1-X Figure 3.2 Radiated Test Setup, position 2-Y 11 Figure 3.3 Radiated Test Setup, position 3-Z