DZO-IQHOMEIQ-H product Zigbee module

OSRAM Version 1.0 non EDOS Product Specification ZPR IQ ZigBee module Page 1 of 4 Issue: 19.09.2014 Status: Comments: Approvers MKT R&D Dai David For information: Overview: The IQ ZigBee module is to be integrated into lamps to realize ZigBee functions. 1. G ENERAL D ESCRIPTION 1.1. Product identification IQ ‐ H product Zigbee module 1.2. ZigBee IC Marvell 88MZ100 1.3. Interface PWM/UART/IIC/SPI; 1ADC; TX & RX for test 1.4. Typical voltage 3.3V 1.5. Communication protocol ZigBee 2012 PRO & ZigBee Light Link 1.0 1.6. Operation Temperature ‐ 40~105 °C 2. E LECTRICAL REQUIREMENTS 2.1. Nominal voltage range 2.2~3.6V 2.2. Nominal operating current Receiver current(with active CPU 32MHz): 21mA TX current(with active CPU 32MHz): 34mA ‐ 3. M ECHANICAL REQUIREMENT 3.1. Terminals Soldering PAD PIN connector 3.2. Size 14.7mm*20mm*1.9mm OSRAM Version 1.0 non EDOS Product Specification ZPR IQ ZigBee module Page 2 of 4 Issue: 19.09.2014 Status: Comments: Approvers MKT R&D Dai David For information: 4. C HANGE I NDEX Vers. Date Change 1.0 15.04.2014 First draft 1.0.1 19.09.2014 Revise Pin assignment C OMMENTS Section Change OSRAM Version 1.0 non EDOS Product Specification ZPR IQ ZigBee module Page 3 of 4 Issue: 19.09.2014 Status: Comments: Approvers MKT R&D Dai David For information: This device complies with part 15 of the FCC Rules. Operation is subject to the followi ng two conditions: (1) This device may n ot cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party re sponsible for compliance could vo id the user's authority to operate the equipment. If the FCC identification nu mber is not visible when the module is installed in side another device, then the outside of the dev ice into which the module is instal led must also display a label re ferring to the enclosed module. Th is exterior label can use word ing such as the following: Contains Transmitter Module FCC ID: DZO-IQHOME or Contains FCC ID: DZO-IQHOME This device complies with Industry Canada lic ence-exempt RSS standard(s). O peration is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any inte rference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilis ateur de l'appareil doit accepter tout brouillage r adioélectrique subi, même si le brouillag e est susceptible d'en compromettre le fonctionnement. If the IC number is not vi sible when the module is install ed inside another device, then the outside of the device into which t he module is installed must also display a l abel referring to the enclosed module. This ex terior label can use wording such as the following: Contains IC: 11099A-IQHOME OSRAM Version 1.0 non EDOS Product Specification ZPR IQ ZigBee module Page 4 of 4 Issue: 19.09.2014 Status: Comments: Approvers MKT R&D Dai David For information: when the module is installed inside another device, the user m anual of this device must cont ain below warning statements; 1. This device complies with Part 15 of the FCC Rules. Operat ion is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, in cluding interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party re sponsible for compliance could void the user's authority to operate the equipment. 3.This device complies with Industry Canada licence-exempt RS S standard(s). Operation is su bject to the following two conditions: (1) this device may not cause in terference, and (2) this device must accept any interference, in cluding interferenc e that may cause undesired oper ation of the device. 4.Le présent appareil est conforme aux CNR d'Industrie Canada applic ables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilis ateur de l'appareil doit accepter tout brouillage r adioélectrique subi, même si le brouillag e est susceptible d'en compromettre le fonctionnement. The devices must be installed and used in strict accordance wit h the manufacturer's instructions as described in the user documentation that comes with the product.

Modular approval Declaration letter We, OSRAM SYLVANIA, Inc. apply limited modular approval for Product Name: IQ-H product Zigbee module Model: IQ Home FCC ID: DZO-IQHOME According to 996369 D01 Module Equip Auth Guide v01r04 and 15.212 requirement: 1) The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must beon the module assembly; Answer: NO 2) The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal; Answer: Yes, all inputs to the modules are buffered through logic or microprocessor inputs. 3) The modular transmitter must have its own power supply regulation. Answer: Yes, a low drop out regulator is used for modular power supply regulation. 4) The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b); Answer: Yes, device is equipped with PCB antenna. (5)The module must demonstrate compliance in a stand-alone configuration; Answer: Yes, distance between modular and AE are longer than 10 cm, refer to setup photo. (6) The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements); Answer: Yes, the modular has a permanent fixed label, and below statement was listed in the Users Manual. The host device must be labelled to display the FCCID of the module Contains FCC ID: DZO-IQHOME (7)The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee; Answer: Yes, the module comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee, Refer to test report and user manual. (8)The module must comply with RF exposure requirements Answer: Yes, transmitter meets MPE calculation of 47 CFR 1.1307. Refer to MPE Reports and Refer to modular installation manual. Signature: Name / title: Christianna Reed / Manager Contact information / address: OSRAM SYLVANIA, Inc. / 100 Endicott Street, Danvers, Massachusetts 01923, United States

DATE : Sep. 22, 2014 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: DZO-IQHOME Product Name: IQ-H product Zigbee module Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...) • Schematics • Block diagram • Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this Agency agreement expiration date: Sep. 22, 2014 to Sep. 21, 2015 By: Christianna Reed Signature Printed Title: Manager On behalf of : OSRAM SYLVANIA Inc. Telephone: 978-750-2884

Label :

The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distancesİ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)]g [Ĝf(GHz)] İ 3.0 for 1-g SAR and İ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is İ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 3. EUT RF Exposure The Max Conducted Peak Output Power is 7.34dBm (5.42mW) in high channel and the Max Conducted Average Output Power is less than 5.42mW. The best case gain of the antenna is 0dBi. 5.42/5*Ĝ2.405=1.68 İ3.0 Conclusion: No SAR test is required. RF exposure evaluation According to KDB 447498:

Report No. : EESZG09150013 Page 1 of 33 TEST REPORT Product : IQ-H product Zigbee module Trade mark : Osram Model/Type reference : IQ Home Serial number : N/A Ratings : DC 3.3V FCC ID : DZO-IQHOME IC : 11099A-IQHOME Report number : EESZG09150013 Date : Sep. 22, 2014 Regulations : See below Test Standards Results 47 CFR FCC Part 15 Subpart C 15.247: 2013 RSS-210 Issue 8 RSS-Gen Issue 3 PASS PASS PASS Prepared for: OSRAM SYLVANIA, Inc. 100 Endicott Street, Danvers, Massachusetts 01923, United States Prepared by: Centre Testing International (Shenzhen) Corporation Hongwei Industrial Zone, 70 Area, Bao’an District, Shenzhen, Guangdong, China TEL: +86-755-3368 3668 FAX: +86-755-3368 3385 Tested by: Reviewed by: Approved by: Date: Sep. 22, 2014 Jimmy Li Lab manager Check No.: 1022568608 Report No. : EESZG09150013 Page 2 of 33 TABLE OF CONTENTS 1. CERTIFICATION INFORMATION ............................................................................................................... 4 2. TEST SUMMARY ........................................................................................................................................ 4 3. MEASUREMENT UNCERTAINTY .............................................................................................................. 5 4. PRODUCT INFORMATION ......................................................................................................................... 5 5. TEST EQUIPMENT LIST ............................................................................................................................. 5 6. SUPPORT EQUIPMENT LIST .................................................................................................................... 5 7. 99% BANDWIDTH MEASUREMENT ......................................................................................................... 6 7.1. LIMITS ................................................................................................................................................. 6 7.2. BLOCK DIAGRAM OF TEST SETUP .................................................................................................. 6 7.3. TEST PROCEDURE ........................................................................................................................... 6 7.4. TEST RESULT .................................................................................................................................... 6 8. 6DB BANDWIDTH MEASUREMENT ......................................................................................................... 9 8.1. LIMITS ................................................................................................................................................. 9 8.2. BLOCK DIAGRAM OF TEST SETUP .................................................................................................. 9 8.3. TEST PROCEDURE ........................................................................................................................... 9 8.4. TEST RESULT .................................................................................................................................... 9 9. POWER SPECTRAL DENSITY ................................................................................................................ 12 9.1. LIMITS ............................................................................................................................................... 12 9.2. BLOCK DIAGRAM OF TEST SETUP ................................................................................................ 12 9.3. TEST PROCEDURE ......................................................................................................................... 12 9.4. TEST RESULT .................................................................................................................................. 12 10. MAXIMUM PEAK CONDUCTED OUTPUT POWER MEASUREMENT .............................................. 15 10.1. LIMITS ............................................................................................................................................... 15 10.2. BLOCK DIAGRAM OF TEST SETUP ................................................................................................ 15 10.3. TEST PROCEDURE ......................................................................................................................... 15 10.4. TEST RESULT .................................................................................................................................. 15 11. CONDUCTED BANDEDGE EMISSION MEASUREMENT ...................................................................... 18 Report No. : EESZG09150013 Page 3 of 33 11.1. LIMITS ............................................................................................................................................... 18 11.2. BLOCK DIAGRAM OF TEST SETUP ................................................................................................ 18 11.3. TEST PROCEDURE ......................................................................................................................... 18 11.4. TEST RESULT .................................................................................................................................. 18 12. CONDUCTED SPURIOUS EMISSION MEASUREMENT .................................................................... 20 12.1. LIMITS ............................................................................................................................................... 20 12.2. BLOCK DIAGRAM OF TEST SETUP ................................................................................................ 20 12.3. TEST PROCEDURE ......................................................................................................................... 20 12.4. TEST RESULT ...............................................................…

Text truncated - open the document above for the full version.