EGT834TXWireless Remote Crane Control

REMOTE CONTROL AND TELEMETRY SYSTEMS Read all Safety and Warnings before installing and operating this system WARNING ! 142108d - CMMDPRO.pm6 Rev D. 12-24-99 REMTRON, INC. 1916 W. Mission Rd., Escondido, CA 92029-1114 PHONE 760-737-7800 FAX 760-737-7810 Radio Remote Control System User's Manual This manual covers the following Remtron models: TransmittersReceivers 21T10o21R10o 21T14o21R14o 21T18o21R22o 21T20o 21T23o 21T34o 21T44o 21T54o AVERTISSEMENT ! Lire toutes les consignes de sécurité et tous les avertissements avant de faire fonctionner ce système. Section 1. System Description 1.1Introduction 1.2Transmitter Description 1.3Receiver Description 1.4Options Section 2. Installation 2.1Installation Planning 2.2Mounting Location 2.3Antenna Mounting 2.4Receiver Installation Section 3. Troubleshooting 3.1General 3.2Transmitter Testing 3.3Receiver Testing Section 4. Maintenance 4.1Periodic Maintenance 4.2Transmitter & Receiver Repairs 4.3Programming 4.4Parts Lists 4.5Ordering & Repairs 4.6Warranty Section 5. Transmitter 5.1Transmitter Description 5.2Transmitter Functions 5.3Transmitter Operation 5.4Options 5.5Troubleshooting 5.6Transmitter Repairs 5.7Transmitter Specifications Section 6. Receiver 6.1Receiver Description 6.2Options 6.3Receiver Specifications i TABLE OF CONTENTS ii Failure to follow the SAFETY RULES may result in serious personal injury. INSTALLATION * GROUND THE RECEIVER CASE. In order to insure safety of the system, the receiver case must be firmly connected to earth ground. * PROVIDE A SAFETY CUTOFF SWITCH. If maintenance is required, the radio must be disconnected from power to prevent accidental activation. * USE PROPER WIRING. Loose or frayed wires can cause accidental activation of machinery. * DO NOT INSTALL IN HOT AREAS. This apparatus can be damaged by heat in excess of 160 F. * DO NOT INSTALL IN HIGH VIBRATION AREAS. The life of this apparatus may be shortened through long exposure to intense shaking or vibration. * DO NOT INSTALL IN AREAS WHERE WATER OR CONTAMINENTS CAN ENTER THE RECEIVER. The receiver is enclosed in a NEMA 12 rated enclosure, however direct spraying of liquids or exposure to caustic environments may result in malfunction of the unit. PERSONAL SAFETY * MAKE SURE MACHINERY IS CLEAR BEFORE OPERATING. Do not activate the remote system unless it is safe to do so. * TURN OFF THE RECEIVER POWER BEFORE WORKING ON MACHINERY. Always disconnect the remote system before doing any maintenance to prevent accidental operation of the machine. CARE * KEEP DRY. If water or other liquids get inside, immediately dry the unit. * KEEP ANTENNAS CLEAN. Keep antenna connections clean and free of corrosion. WARNING ! READ ALL INSTRUCTIONS WARNING INSTRUCTIONS iii Le non respect des CONSIGNES DE SÉCURITÉ peut causer des blessures sérieuses. INSTALLATION * RACCORDER LE BOÎTIER À LA MASSE. Pour que le système fonctionne en toute sécurité, le boîtier du récepteur doit être solidement raccordé à la masse. * FOURNIR UN INTERRUPTEUR DE SÉCURITÉ. Lors de travaux d’entretien du dispositif, déconnecter le poste radio afin d’éviter une mise en marche accidentelle.. * UTILISER LES FILS APPROPRIÉS. Des fils découverts ou usés peuvent provoquer un démarrage accidentel de la machinerie. * NE PAS INSTALLER DANS DES ENDROITS CHAUDS. Des températures supérieures à 160 °F (71°C) peuvent endommager l’appareil. * NE PAS INSTALLER DANS LES ENDROITS SOUMIS À DE FORTES VIBRATIONS. L’exposition prolongée de cet appareil à des vibrations ou des secousses intenses peut en réduire la durée de vie. * NE PAS EXPOSER LE RÉCEPTEUR À L’EAU OU À TOUT AUTRE CONTAMINANT. Bien que le récepteur soit entouré d’une enceinte répondant à la norme NEMA 12, l’exposition directe à un liquide ou à un environnement caustique peut entraîner un mauvais fonctionnement de l’appareil. SÉCURITÉ * S’ASSURER QUE LA MACHINERIE EST DÉGAGÉE AVANT DE LA FAIRE FONCTIONNER. Ne pas faire fonctionner le système de téléguidage à moins que cela puisse être fait en toute sécurité. * METTRE LE RÉCEPTEUR HORS TENSION AVANT D’EFFECTEUR DES TRAVAUX SUR LA MACHINERIE. Afin de prévenir la mise en marche accidentelle de la machinerie, toujours débrancher le système de téléguidage avant de d’effectuer des travaux d’entretien. ENTRETIEN * GARDER AU SEC. Sécher immédiatement l’appareil, s’il est exposé à de l’eau ou tout autre liquide. * GARDER LES ANTENNES PROPRES. Garder les raccordements d’antenne propres et exempts de corrosion. AVERTISSEMENT ! LIRE TOUTES LES CONSIGNES CONSIGNES DE SÉCURITÉ SECTION 1: SYSTEM DESCRIPTION 1.1 INTRODUCTION The Remtron Radio Remote Control Systems are designed for control of industrial rated machinery. This system complies with requirements for operation under part 15 of the FCC rules and regulations. This means neither the operator nor the company need apply or register for a license to operate this equipment. The basic system consists of a transmitter and a receiver. The transmitter sends commands to the receiver by means of radio waves in the 900 MHz band. Receivers operate from 115 VAC 50/60 Hz power. Operation from 220 VAC is also available. 1.2 TRANSMITTER DESCRIPTION The hand held transmitters are housed in rugged cases molded from a modified polymer plastic that stands up to extremely rugged use. A key feature of the hand held transmitters is Remtron's patented switch assembly for control inputs. This long life elastomeric keypad is ergonomically designed to provide easy operation over long periods of time with exceptional reliability. The lever and joystick transmitters provide rugged yet lightweight housings that allow daylong use without a strain on the back. All the transmitter functions are controlled by a microprocessor with a special memory for configuration information. This offers a great degree of capability and versatility while at the same time providing simplicity of operation and maintenance. The antenna is internal to most transmitter cases, protecting it from damage. An indicator LED prov…

Text truncated - open the document above for the full version.

REMOTE CONTROL AND TELEMETRY SYSTEMS Read all Safety and Warnings before installing and operating this system WARNING ! 142108d - CMMDPRO.pm6 Rev D. 12-24-99 REMTRON, INC. 1916 W. Mission Rd., Escondido, CA 92029-1114 PHONE 760-737-7800 FAX 760-737-7810 Radio Remote Control System User's Manual This manual covers the following Remtron models: TransmittersReceivers 21T10o21R10o 21T14o21R14o 21T18o21R22o 21T20o 21T23o 21T34o 21T44o 21T54o AVERTISSEMENT ! Lire toutes les consignes de sécurité et tous les avertissements avant de faire fonctionner ce système. Section 1. System Description 1.1Introduction 1.2Transmitter Description 1.3Receiver Description 1.4Options Section 2. Installation 2.1Installation Planning 2.2Mounting Location 2.3Antenna Mounting 2.4Receiver Installation Section 3. Troubleshooting 3.1General 3.2Transmitter Testing 3.3Receiver Testing Section 4. Maintenance 4.1Periodic Maintenance 4.2Transmitter & Receiver Repairs 4.3Programming 4.4Parts Lists 4.5Ordering & Repairs 4.6Warranty Section 5. Transmitter 5.1Transmitter Description 5.2Transmitter Functions 5.3Transmitter Operation 5.4Options 5.5Troubleshooting 5.6Transmitter Repairs 5.7Transmitter Specifications Section 6. Receiver 6.1Receiver Description 6.2Options 6.3Receiver Specifications i TABLE OF CONTENTS ii Failure to follow the SAFETY RULES may result in serious personal injury. INSTALLATION * GROUND THE RECEIVER CASE. In order to insure safety of the system, the receiver case must be firmly connected to earth ground. * PROVIDE A SAFETY CUTOFF SWITCH. If maintenance is required, the radio must be disconnected from power to prevent accidental activation. * USE PROPER WIRING. Loose or frayed wires can cause accidental activation of machinery. * DO NOT INSTALL IN HOT AREAS. This apparatus can be damaged by heat in excess of 160 F. * DO NOT INSTALL IN HIGH VIBRATION AREAS. The life of this apparatus may be shortened through long exposure to intense shaking or vibration. * DO NOT INSTALL IN AREAS WHERE WATER OR CONTAMINENTS CAN ENTER THE RECEIVER. The receiver is enclosed in a NEMA 12 rated enclosure, however direct spraying of liquids or exposure to caustic environments may result in malfunction of the unit. PERSONAL SAFETY * MAKE SURE MACHINERY IS CLEAR BEFORE OPERATING. Do not activate the remote system unless it is safe to do so. * TURN OFF THE RECEIVER POWER BEFORE WORKING ON MACHINERY. Always disconnect the remote system before doing any maintenance to prevent accidental operation of the machine. CARE * KEEP DRY. If water or other liquids get inside, immediately dry the unit. * KEEP ANTENNAS CLEAN. Keep antenna connections clean and free of corrosion. WARNING ! READ ALL INSTRUCTIONS WARNING INSTRUCTIONS iii Le non respect des CONSIGNES DE SÉCURITÉ peut causer des blessures sérieuses. INSTALLATION * RACCORDER LE BOÎTIER À LA MASSE. Pour que le système fonctionne en toute sécurité, le boîtier du récepteur doit être solidement raccordé à la masse. * FOURNIR UN INTERRUPTEUR DE SÉCURITÉ. Lors de travaux d’entretien du dispositif, déconnecter le poste radio afin d’éviter une mise en marche accidentelle.. * UTILISER LES FILS APPROPRIÉS. Des fils découverts ou usés peuvent provoquer un démarrage accidentel de la machinerie. * NE PAS INSTALLER DANS DES ENDROITS CHAUDS. Des températures supérieures à 160 °F (71°C) peuvent endommager l’appareil. * NE PAS INSTALLER DANS LES ENDROITS SOUMIS À DE FORTES VIBRATIONS. L’exposition prolongée de cet appareil à des vibrations ou des secousses intenses peut en réduire la durée de vie. * NE PAS EXPOSER LE RÉCEPTEUR À L’EAU OU À TOUT AUTRE CONTAMINANT. Bien que le récepteur soit entouré d’une enceinte répondant à la norme NEMA 12, l’exposition directe à un liquide ou à un environnement caustique peut entraîner un mauvais fonctionnement de l’appareil. SÉCURITÉ * S’ASSURER QUE LA MACHINERIE EST DÉGAGÉE AVANT DE LA FAIRE FONCTIONNER. Ne pas faire fonctionner le système de téléguidage à moins que cela puisse être fait en toute sécurité. * METTRE LE RÉCEPTEUR HORS TENSION AVANT D’EFFECTEUR DES TRAVAUX SUR LA MACHINERIE. Afin de prévenir la mise en marche accidentelle de la machinerie, toujours débrancher le système de téléguidage avant de d’effectuer des travaux d’entretien. ENTRETIEN * GARDER AU SEC. Sécher immédiatement l’appareil, s’il est exposé à de l’eau ou tout autre liquide. * GARDER LES ANTENNES PROPRES. Garder les raccordements d’antenne propres et exempts de corrosion. AVERTISSEMENT ! LIRE TOUTES LES CONSIGNES CONSIGNES DE SÉCURITÉ SECTION 1: SYSTEM DESCRIPTION 1.1 INTRODUCTION The Remtron Radio Remote Control Systems are designed for control of industrial rated machinery. This system complies with requirements for operation under part 15 of the FCC rules and regulations. This means neither the operator nor the company need apply or register for a license to operate this equipment. The basic system consists of a transmitter and a receiver. The transmitter sends commands to the receiver by means of radio waves in the 900 MHz band. Receivers operate from 115 VAC 50/60 Hz power. Operation from 220 VAC is also available. 1.2 TRANSMITTER DESCRIPTION The hand held transmitters are housed in rugged cases molded from a modified polymer plastic that stands up to extremely rugged use. A key feature of the hand held transmitters is Remtron's patented switch assembly for control inputs. This long life elastomeric keypad is ergonomically designed to provide easy operation over long periods of time with exceptional reliability. The lever and joystick transmitters provide rugged yet lightweight housings that allow daylong use without a strain on the back. All the transmitter functions are controlled by a microprocessor with a special memory for configuration information. This offers a great degree of capability and versatility while at the same time providing simplicity of operation and maintenance. The antenna is internal to most transmitter cases, protecting it from damage. An indicator LED prov…

Text truncated - open the document above for the full version.

Date: February 20, 1997 Sheet 1 of 1 Size Document Number REV B 800134-04 - Title BLOCK DIAGRAM, 21T10 Transmitter ESCONDIDO, CA 92029 1916 W MISSION RD. REMTRON, INC. DATE APPROVED 02/20/97 MPG REVISIONS DESCRIPTIONLTR - INITIAL RELEASE +5V This document is the property of Remtron Inc. and contains PROPRIETARY information. All recipients hereof agree to the foregoing, and agree which it is loaned without the express written consent of Remtron Inc. not to make any duplication thereof or to disclose the information herein to others or to use it for any purpose other then that for 1.5V AA 1.5V AA VR1 GROUND SWITCHTX ON +5VD EEPROM PROGRAMMING PORT CPU 12.8MHZ KEYPAD INPUTS RF GROUND GND +5VD LOOP MODULATION +5V BUFFER/AMP +5V AMP +5V INTERNAL MICROSTRIP ANTENNA LPF SWITCHED RF GROUND FILTER 902-928MHz PLL FILE NO. 80013404.-

Date: February 20, 1997 Sheet 1 of 1 Size Document Number REV B 800134-04 - Title BLOCK DIAGRAM, 21T10 Transmitter ESCONDIDO, CA 92029 1916 W MISSION RD. REMTRON, INC. DATE APPROVED 02/20/97 MPG REVISIONS DESCRIPTIONLTR - INITIAL RELEASE +5V This document is the property of Remtron Inc. and contains PROPRIETARY information. All recipients hereof agree to the foregoing, and agree which it is loaned without the express written consent of Remtron Inc. not to make any duplication thereof or to disclose the information herein to others or to use it for any purpose other then that for 1.5V AA 1.5V AA VR1 GROUND SWITCHTX ON +5VD EEPROM PROGRAMMING PORT CPU 12.8MHZ KEYPAD INPUTS RF GROUND GND +5VD LOOP MODULATION +5V BUFFER/AMP +5V AMP +5V INTERNAL MICROSTRIP ANTENNA LPF SWITCHED RF GROUND FILTER 902-928MHz PLL FILE NO. 80013404.-

February 3, 2000 FEDERAL COMMUNICATIONS COMMISSION Equipment Approval Services P.O. Box 358315 Pittsburgh, PA 15251-5315 FCC Confirmation Number: EA96572 Correspondence Reference Number: 11788 FCC ID EGT834TX RE: New Exhibits Added On behalf of our client, Remtron. We are submitting new exhibits for their product. Thank you for your assistance in this matter. Sincerely, DNB ENGINEERING, INC. Jeff Williams Documentation Supervisor

FCC ID: EGT834TX DATE: 11/30/99 REPORT #06034-5F 10 2.7 Photograph of EUT - per 2.1033(b)(7) Belly Box Transmitter 21T34

FCC ID: EGT834TX DATE: 11/30/99 REPORT #06034-5F 10 2.7 Photograph of EUT - per 2.1033(b)(7) Belly Box Transmitter 21T34

FCC ID: EGT834TX DATE: 11/30/99 REPORT #06034-5F 20 4. LABELING REQUIREMENTS - PER 2.1033(B)(7) Label will be constructed of 0.02 inch plastic attached as shown on the equipment with permanent adhesive. All information on the label will be etched or screened. All methods will exceed the expected lifetime of the equipment. The label will be large enough to allow all information to be readily legible. 4.1 Additional Label Required Shown above is a copy of the label with the Part 15.19 Compliance Statement, Location of required information is checked “below”. The label will be placed in a conspicuous location on the device. The device is too small for a compliance label. Therefore the label will be placed in a prominent location in the Instruction Manual or other information supplied to the user. The device is too small for a compliance label. The label will be placed on the container in which the device will be marketed. 4.2 Photograph of Label Placement and Contents PDF File. See the attachment that was electronically submitted. This device complies with Part 15 of the FCC Rules. Operation is subject to the following tow conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

FCC ID: EGT834TX DATE: 11/30/99 REPORT #06034-5F 20 4. LABELING REQUIREMENTS - PER 2.1033(B)(7) Label will be constructed of 0.02 inch plastic attached as shown on the equipment with permanent adhesive. All information on the label will be etched or screened. All methods will exceed the expected lifetime of the equipment. The label will be large enough to allow all information to be readily legible. 4.1 Additional Label Required Shown above is a copy of the label with the Part 15.19 Compliance Statement, Location of required information is checked “below”. The label will be placed in a conspicuous location on the device. The device is too small for a compliance label. Therefore the label will be placed in a prominent location in the Instruction Manual or other information supplied to the user. The device is too small for a compliance label. The label will be placed on the container in which the device will be marketed. 4.2 Photograph of Label Placement and Contents PDF File. See the attachment that was electronically submitted. This device complies with Part 15 of the FCC Rules. Operation is subject to the following tow conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

FCC ID: EGT834TX DATE: 11/30/99 REPORT #06034-5F 11 Front and Back of Belly Box Transmitter 21T34 PCB

SECTION 5: TRANSMITTER 5.1 TRANSMITTER DESCRIPTION The 21T34 transmitter is housed in a rugged aluminum case. The transmitter uses sealed push-button and toggle switches for discrete inputs, and high quality rotary switches for motor control functions. It has an easy access battery compartment for the long life Alkaline batteries. Each transmitter is provided with a shoulder strap for ease of use. All transmitter functions are controlled by a microprocessor with a special memory for configuration information. This arrangement offers a great degree of capability and versatility while at the same time providing simplicity of operation and maintenance. The antenna is enclosed in a protective cover on the front of the transmitter case, protecting it from damage. An indicator LED provides a quick visual check of the transmitters status. The crane control transmitters are designed to be very efficient. Only three AA batteries are needed to provide power for the transmitter for two month's normal use. Up to 9 batteries may be used to extend the operating time much longer. An additional feature automatically shuts the transmitter off after a preset time interval of inactivity to further extend the battery life. The microprocessor contains a nonvolatile memory that retains the frequency, address and particular operating parameters for the system. It is programmable by means of PC compatible computers equipped with an RS-232 serial port (RAC17) or by an independent programming unit (RAC16). 5.2 TRANSMITTER FUNCTIONS The 21T34 transmitter uses sealed push-buttons, toggle switches and paddle operated switches for control of radio and command functions. The following describes the function of the switches, operational procedures and particular characteristics of the transmitter. Refer to Figure 5.2. ON/ALARM. Puts the system into the active mode. The transmitter will remain active until the OFF/ESTOP is pressed or the transmitter turns itself off (see Auto Off). Sends an ALARM command to the receiver while the button is depressed. 5.1 Figure 5.1 21T34 Transmitter WARNING Do not operate the system until you are familiar with radio controlled crane operation. If you are not familiar with radio controlled crane operation, contact your supervisor before attempting to use the radio control system. AVERTISSEMENT ! Ne pas faire fonctionner le système avant de bien connaître le fonctionnement d’une grue par téléguidage. Contacter le superviseur avant de faire toute tentative de mise en marche par téléguidage, si le fonctionnement n’est pas connu. SECTION 5: TRANSMITTER 5.2 Figure 5.2 21T23 Transmitter OFF/ESTOP. While depressed, sends an Emergency Stop command to the receiver. The transmitter does not need to be in the active mode to send this command. After this button is released the transmitter will be turned off. TEST LED. The Test LED provides an indication of the transmitter operation. When the transmitter is OFF the TEST LED will be off. When the transmitter is ON, the TEST LED will flash at a low rate when no command is being sent and at a high rate when a command is being sent. If the batteries are getting low, the TEST LED will flash on-off (1/2 second on and 1/2 second off) while the transmitter is ON. The transmitter may still be used, however, the batteries should be changed at the next convenient opportunity. If the TEST LED remains on continuously there is either a switch activated at the time the transmitter is turned on, or a general failure that requires factory service. If the TEST LED remains lit continuously on power-up, insure no other switches are pressed while attempting to turn the transmitter on. Auto Off. The transmitter will turn itself off if no commands have been sent for a predetermined time. Normally this time is set to 15 minutes, however it may be programmed for other times. Paddles. Paddle controls provide 5 steps in each direction. When in the neutral (center) position no commands are sent. When a paddle is displaced from the neutral position a command indicating the amount of displacement is generated; that is, the further the paddle is pushed the faster the movement will be commanded. PTO Switch. The Push To Operate (PTO or "Dead Man Switch") is a safety device. The 21T34 is normally programmed so the bar which activates this function must be depressed before any motor or other critical function PTO Bar Off/ESTOP Switch On/Alarm Switch Antenna Motor Control Paddles SECTION 5: TRANSMITTER 5.3 1.Press and release the ON/ALARM button. Verify that the test LED starts flashing at a low rate. If equipped, the Alarm on the crane should sound. 2.For functions that do not require the PTO switch, press a switch or operate a paddle to activate the function. 3.For switches that require the use of the PTO switch, hold the PTO switch down while pressing a command switch to activate the function. 4.To stop any function, release the function and/or PTO switch. 5.To turn the transmitter off, press the OFF/ESTOP button. Note that the transmitter will turn itself off if no commands are changed for a predetermined time. 5.4 OPTIONS Harness. An optional full harness is available for the transmitter which makes long shift operation less tiring. First Come-First Serve (FCFS). The FCFS option allows one receiver to be controlled by more than one transmitter, but only one at a time. When all the transmitters in the system are off, the receiver will scan (look for) the frequency of each of the transmitters in the system. When the receiver detects the signal of a valid transmitter, it will stop scanning and lock on to that transmitter. So long as it continues to receive signals from that transmitter, it will not scan. If another transmitter or transmitters are turned on, their signals will not be detected by the receiver. If your transmitter is the first one turned on, it will take control of the receiver. If another transmitter was turned on prior to yours, your transmitter will have no effect on…

Text truncated - open the document above for the full version.

06034-5 Remtron MN 21T34(4/99)DNB Engineering, Inc.Page 1 RADIATED EMISSIONS FCC Part 15, Sub-part C (15.209) File #Engr.:Date : Site :1Distance3meter Cables 1.2 Bicon:186 Log: 11 Amp 1 : 65 Mea Type AmpCableAntennaTotalAve Freq.Meas'dFactorsFactorsFactorsFactorsTotalLimitDeltaAzimuthHeightHor/HP/QP (MHz)(dBuV)(dB)(dB)(dB)(dBuV/m)(dBuV/m)(dBuV/m)(dB)(degree)(m)VertR&SPeakComments ######92.827.3-8.226.0-9.583.3094.0####1721VertR&SQP Run #1 Vert ######83.227.3-11.226.0-12.570.7094.0####1653Hor/R&SQP ######95.627.3-11.226.1-12.483.2094.0####1721VertR&SQP Run #2 Freq set at 915. 06034-5Jeff WilliamsDec 01, 1999 1100 E. Chalk Creek Rd. Coalville, UT, 84017 Data not valid for report unless signed by DNB personnel _____________________________ Phone (435) 336-4433 Fax (435) 336-4436

FCC ID: EGT834TX DATE: 11/30/99 REPORT #06034-5F 1 DNB ENGINEERING, INC. CERTIFICATION FOR INTENTIONAL RADIATOR Per Part 15 Subpart C (CFR 47, 15,203, 15.249 & 15.209) EUT: EUT: Belly Box Transmitter (903.0 MHz to 927.0 MHz)(903.0 MHz toBelly Box Transmitter (903.0 MHz to 927.0 MHz)(903.0 MHz to 927.0 MHz)(903.0 MHz to 927.0 MHz)(903.0 MHz to 927.0 MHz)(903.0927.0 MHz)(903.0 MHz to 927.0 MHz)(903.0 MHz to 927.0 MHz)(903.0 MHz to 927.0 MHz)MHz to 927.0 MHz) Model No. 21T34 903.0 MHz to 927.0 MHz PREPARED FOR APPLICANT: Remtron 1916 W. Mission Rd Escondido, CA 92029-1114 (760) 737-7800 REPORT #06034-5F Test Date: 11/30/99 Prepared By: DNB ENGINEERING, INC. 1100 East Chalk Creek Rd. Coalville, Utah 84017 Tel: 1(435) 336-4433 Industry Canada Lab Code IC 3386 FCC ID: EGT834TX DATE: 11/30/99 REPORT #06034-5F 2 Revision Letter Number of Pages Page No. of Rev. DescriptionDate A33Document Release1/14/00 FCC ID: EGT834TX DATE: 11/30/99 REPORT #06034-5F 3 TRANSMITTAL SUMMARY Unit tested:Belly Box Transmitter (903.0 MHz to 927.0 MHz)(903.0 MHz to 927.0 MHz)(903.0 MHz to 927.0 MHz)(903.0 MHz to 927.0 MHz) Model #: 21T34 FCC ID: EGT834TX Specifications: ANSI C63.4 1992 and CFR 47 FCC part 15 Subpart C Purpose of Report: This report was prepared to document the status of the with requirements of the standards listed above. Requirements not applicable to EUT Part 15.37 - Not applicable Emergency Broadcast System - Not applicable Spread Spectrum Exhibit - Not applicable Scanning Receiver - Not applicable Test SummaryThe EUT’s compliance status according to the tests performed is as follows. REQUIREMENTSSTATUS FCC part 15 Subpart C per 15.203, 15.249 & 15.209COMPLIANT Industry Canada Lab Code IC 3386 The report shall not be reproduced, except in full, without the written approval of DNB ENGINEERING, INC. Results contained in this report relate only to the item tested. FCC ID: EGT834TX DATE: 11/30/99 REPORT #06034-5F 4 CERTIFICATION OF TEST DATA - per 2.911(d) This report, containing emissions test data and evaluations, has been prepared by an independent electromagnetic compatibility laboratory, DNB ENGINEERING, in accordance with the applicable specifications and instructions required per the Introduction. The American Association has evaluated DNB Engineering to do these tests for Laboratory Accreditation, A2LA. The data evaluation and equipment configuration presented herein are a true and accurate representation of the measurements of the test emissions characteristics as of the dates and at the times of the test under the conditions herein specified. Equipment Tested:Belly Box Transmitter (903.0 MHz to 927.0 MHz)(903.0 MHz to 927.0 MHz) Model #:21T34 FCC ID#: EGT834TX Dates of Test:11/30/99-12/8/99 Test Performed: ____________________________________________ Yancey Staples/Jeff WilliamsDate Test Technician Test Report Reviewed: ____________________________________________ Rick LinfordDate Facility Manager Regulatory Engineer Industry Canada Lab Code IC 3386 FCC ID: EGT834TX DATE: 11/30/99 REPORT #06034-5F 5 1.INTRODUCTION.............................................................................................................................6 1.1ADMINISTRATIVE DATA PER 2.1033(A) AND 2.911(C).........................................................................6 1.1.1REQUEST FOR CERTIFICATION Per 2.1033(b)1:.............................................................6 1.2RELATED SUBMITTALS/GRANTS.......................................................................................................6 1.3PURPOSE OF TESTS........................................................................................................................6 2.TEST DESCRIPTION......................................................................................................................7 2.1TEST CONFIGURATION....................................................................................................................7 2.2EQUIPMENT DESCRIPTION...............................................................................................................7 2.2.1Mode of Operation................................................................................................................7 2.3ANTENNA REQUIREMENT - PER 15.203.............................................................................................7 2.4DOCUMENTED EMC CONTROL MEASURES........................................................................................7 2.5CIRCUIT DESCRIPTION - PER 2.1033(B)4..........................................................................................8 2.6SCHEMATICS..................................................................................................................................9 2.7PHOTOGRAPH OF EUT - PER 2.1033(B)(7).....................................................................................10 3.EMISSIONS FCC PART 15...........................................................................................................12 3.1RADIATED EMISSIONS TEST SETUP AND PROCEDURE - PER 2.1033(B)(6) PER 2.947(A).....................12 3.2SPURIOUS RADIATION TEST SITE PER 2.1033(B)6.........................................................................12 3.2.1Example Of Typical Calculation Per 2.1033(b)6...............................................................14 3.2.2Fundamental Field Strength...............................................................................................15 3.2.3Harmonics Emissions.........................................................................................................16 3.2.4Spurious Emissions not associated with fundamental.........................................................17 3.2.5Emission at Band Edges.....................................................................................................18 3.2.6Photograph of Radiated Test Setup - per 2.1033(b)(7).......................................................19 …

Text truncated - open the document above for the full version.

06034-5 Remtron MN 21T34(4/99)DNB Engineering, Inc.Page 1 RADIATED EMISSIONS FCC Part 15, Sub-part C (15.209) File #Engr.:Date : Site …

Text truncated - open the document above for the full version.