ELVATDA434 MHz RF Programmer

Feature Setup The RF programmer allows you to select the feature set that you have installed. Please refer to the chart below to determine which functions are required for the particular feature set you are installing. Selecting Programmable Features 1) Press the POWER button to turn the system ON. 2) Once powered up the MENU screen will be displayed. 3) Use the UP & DN arrows to scroll through the programmable features. Once you locate the desired feature to change, press the > arrow to advance to the next screen. You should see the default setting of the system 4) Press the SET button to scroll through the available settings. Once the desired setting is shown on the screen, press the < to return to the feature chart selectable options or press SEND to transmit to the system you are installing. NOTE 1: You must access the RF receive bank on Option programming to SEND the selected infor- mation to the CA 425, please refer to the programming section on the next page. Using the M1 function The RF Programmer has a memory function that will allow you to store the most common of settings. Once you have selected the settings that you want to store press and hold M1 button for 3 seconds. The screen will display "Reading to Memory". You can access the stored settings anytime by pressing the M1 button. RF Programmer SecurityRemote Start1 Way/2 Way CA 125ONOFF1 WAY CA 135ONOFF2 WAY CA 145ONOFF2 WAY CA 535OFFON1 WAY CA 545ONON2 WAY CA 645ONON2 WAY For technical assisance please call 800-421-3209 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions. (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. Per FCC 15.21, you are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.

Helen Zhao Subject: FW: ??: RE: ??: RE: ??: RE: NUTEK CORPORATION, FCC ID: ELVATDA, Assessment NO.: AN04T4027, Notice#1 6/7/2005 From: [email protected] [mailto:[email protected]] Sent: Monday, June 06, 2005 6:48 PM To: Helen Zhao Cc: [email protected]; [email protected] Subject: ??: RE: ??: RE: ??: RE: NUTEK CORPORATION, FCC ID: ELVATDA, Assessment NO.: AN04T4027, Notice#1 Hi, Helen See Answers below. Best Regards, Rick -----Original Message----- From: Compliance Certification Services [mailto:[email protected]] Sent: Friday, November 05, 2004 2:42 PM To: Helen Zhao Subject: NUTEK CORPORATION, FCC ID: ELVATDA, Assessment NO.: AN04T4027, Notice#1 Question #1: The test report includes the photos to show the EUT was tested in three orthogonal planes (X, Y, Z axis) when it was powered by battery. However the test setup photos show that the radiated emission was test when the EUT was powered by AC/DC adaptor. Please clarify how the radiated emission was tested. Answer: The test report was updated. Question #2: Based upon FCC15.35(c), when the radiated emission limits are expressed in terms of the average value of the emission, and pulsed operation is employed, the measurement field strength shall be determined by averaging over one complete pulse train, including blanking intervals, or 0.1 seconds, which ever is less. Please correct average reading at 1302 MHz. Answer: The test report was updated. Question #3: Please verify that the user manual in the filing is the correct manual for the device. It does not agree with other documents in the filing in many areas. Answer: Please find the user manual. Best regards, Helen Zhao The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 30 days of the original e-mail date may result in application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender. ________________________________________________________________________ This e-mail transmission is confidential and intended solely for being reviewed by the recipient(s) identified above. If you are not an identified recipient, please ensure that this communication remains confidential and promptly return it to the sender. Please contact immediately by phone (Tel: 886-2-2299-9720) for any problem with this transmission, Thank you for your attention. 6/7/2005

Report No: 40517403 External Photos Report No: 40517403 External Photos Report No: 40517403 External Photos Report No: 40517403 External Photos

FCC ID LABEL FORMAT AND LOCATION Applicant: NUTEK CORPORATION FCC ID: ELVATDA FCC ID: ELVATDA This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID LABEL AREA

Report No: 40517403 Internal Photos Report No: 40517403 Internal Photos Report No: 40517403 Internal Photos Report No: 40517403 Internal Photos Report No: 40517403 Internal Photos Report No: 40517403 Internal Photos

Compliance Certification Services Inc. Report No: 40517403-RP Date of Issue: July 01, 2004 FCC ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT CERTIFICATION TO FCC PART 15 REQUIREMENTS for INTENTIONAL RADIATOR of RF PROGRAMMER FCC ID Number : ELVATDA Trade Name : N/A Model Number : 1027424(RF Programmer) Agency Series : N/A Report Number : 40517403-RP Date : November 11, 2004 Prepared for NUTEK CORPORATION 5F, NO. 3, Alley 6, Lane 45, Pao-Hsing Rd., Hsing-Tien City, Taipei, TAIWAN, R.O.C. Prepared by Compliance Certification Services Inc. No. 165, Chung Sheng Road, Hsin Tien City, Taipei, Taiwan, R. O. C. TEL: (02)2217-0894 FAX: (02)2217-1029 This report shall not be reproduced, except in full, without the written approval of Compliance Certification Services Inc. Page 1 of 11 Rev. 00 Compliance Certification Services Inc. Report No: 40517403-RP Date of Issue: November 11, 2004 TABLE OF CONTENTS 1. VERIFICATION OF COMPLIANCE...............................................................3 2. PRODUCT DESCRIPTION.................................................................................4 3. TEST FACILITY...................................................................................................4 4. MEASUREMENT STANDARDS.......................................................................4 5. TEST METHODLOGY........................................................................................4 6. MEASUREMENT EQUIPMENT USED...........................................................5 7. POWERLINE RFI LIMIT....................................................................................6 8. RADIATED EMISSION LIMITS.......................................................................6 9. SYSTEM TEST CONFIGURATION.................................................................7 10. TEST PROCEDURE.............................................................................................8 11. EQUIPMENT MODIFICATIONS......................................................................9 12. TEST RESULT.....................................................................................................10 12.1. MAXIMUM MODULATION PERCENTAGE (M%)...............................10 12.2. THE EMISSIONS BANDWIDTH.................................................................10 APPENDIX TEST DATA & PHOTOGRAPHS OF EUT....................................11 Page 2 Rev. 00 Compliance Certification Services Inc. Report No: 40517403-RP Date of Issue: November 11, 2004 1. VERIFICATION OF COMPLIANCE COMPANY NAME : NUTEK CORPORATION 5F, No. 3, Alley 6, Lane 45, Pao-Hsing Rd., Hsing-Tien City, Taipei, TAIWAN, R.O.C. CONTACT PERSON : RUBY HSIEH / MARKETING DEPT. TELEPHONE NO. : (886-2) 2918-9478 EUT DESCRIPTION : RF PROGRAMMER MODEL NAME/NUMBER : 1027424(RF Programmer) FCC ID : ELVATDA DATE TESTED : May 1820 & June 25, 2004 REPORT NUMBER : 40517403-RP TYPE OF EQUIPMENT SECURITY EQUIPMENT (INTENTIONAL RADIATOR) EQUIPMENT TYPE 434 MHz RF PROGRAMMER MEASUREMENT PROCEDURE ANSI 63.4 / 2000 LIMIT TYPE CERTIFICATION FCC RULE CFR 47, PART 15 The above equipment was tested by Compliance Certification Services Inc. for compliance with the requirements set forth in the FCC CFR 47, PART 15. The results of testing in this report apply to the product/system which was tested only. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Warning: This document reports conditions under which testing was conducted and results of tests performed. This document may not be altered or revised in any way unless done so by Compliance Certification Services Inc. and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by Compliance Certification Services Inc. will constitute fraud and shall nullify the document. Approved by: Reviewed by: Page 3 David Wang Rick Yeo Manager Manager Compliance Certification Services Inc. Compliance Certification Services Inc. Rev. 00 Compliance Certification Services Inc. Report No: 40517403-RP Date of Issue: November 11, 2004 2. PRODUCT DESCRIPTION Fundamental Frequency 434 MHz Power Source Powered by AA batteries (Rating: 6 × 1.5Vdc) Transmitting Time Periodic < 5 seconds Associated Receiver Model: 1027424 (DoC) Support Equipment: AC Adaptor Model No.: N4120-1330-DC Input: AC 120V, 60Hz Output: DC 13V, 300mA Notes: EUT is not intended to be sold with AC adaptor under test in this report. 3. TEST FACILITY The open area test sites and conducted measurement facilities used to collect the radiated data are located at No. 165 & No. 199, Chung Sheng Road, Hsin Tien City, Taipei, Taiwan R.O.C. The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22. 4. MEASUREMENT STANDARDS The site is constructed and calibrated in conformance with the requirements of ANSI C63.4/2001. 5. TEST METHODOLOGY For an intentional radiator, the spectrum shall be investigated from the lowest radio frequency signal generated in the device, without going below 9 KHz, up to at least the tenth harmonic of the highest fundamental frequency or to 40 GHz, whichever is lower. (CFR 47 Section 15.33) Page 4 Rev. 00 Compliance Certification Services Inc. Report No: 40517403-RP Date of Issue: November 11, 2004 6. MEASUREMENT EQUIPMENT USED EQUIPMENT TYPE MFR MODEL NUMBER SERIAL NUMBER CAL. DUE SITE NSA CCS E Site N/A 09/13/2004 EMI TEST RECEIVER R&S DSAI-D / ESBI-RF 827832/001 82706/003 03/08/2005 ANTENNA SCHAFFNER CBL 6112B 2802 09/27/2004 AMPLIFIER H.P. 8447D A 2727A05764 04/30/2005 CABLE BELDEN 9913 N-TYPE#E2&E3 03/05/2005 THERMO- HYGRO METER TFA N/A NO.6 11/23/2004 EQUIPMENTT YPE MFR MODEL NUMBER SERIAL NUMBER CAL. DUE EMC ANALYZER (100Hz-22GHz) HP 8566B 2937A06102 06/25/2004 ANTENNA (1-18GHz) EMCO 3115 5761 02/02/2005 AMPLIFIER (1-26.5GHz) HP 8449B 3008A01266 02/15/2005 CABLE (1-18GHz) JYEBAO HUBER+SUHNER LL142 SUCOFLEX 104 SMA-RS1&2 SMA-RS3 02/15/200…

Text truncated - open the document above for the full version.

Report No: 40517403 Setup Photos Radiated Emission (Worst Mode) X-Axis Y- A x i s Report No: 40517403 Setup Photos Z-Axis Report No: 40517403 Setup Photos Conducted Emission (Worst Mode)