ELVATRNDTransceiver

128-9296 1/24 1 PATENTED: www.voxxintl.com/company/patents Before You Begin Page 2 Wire Harnesses Quick View Page 3 - 4 Mounting Of The Major Components Page 5 Pin Power Harness Wiring Page 6 - 7 12 Pin Accessory Input/Output Harness Wiring Page 7 - 9 4 Pin GND, Alarm Bypass Output & Parking Light Harness Page 11 Door Unlock Harness Wiring Page 12 - 13 Telematic Port Information Page 13 6 Pin Antenna Harness Page 13 Diesel Engine Setting Information Page 14 DBI Port Information Page 14 Engine Monitoring Selections, (Voltage Tach, DBI, Hybrid,) Page 14 Tach Programming Page 14 & 21 Diagnostics Access & Information Page 15 Testing Your Installation Hood Pin Safety Page 15 Manual Override Safety Testing and Operation Page 15 - 16 Manual Override Safety Testing and Operation Page 15 - 16 Completing Your Installation Page 18 Programming Transmitters Page 19 Programming Alarm Feature Bank 2 Page 19 & 20 Tach Programming Page 14 & 21 Circuit Wiring Layout Page 23 Table Of Contents: Model PRO9056TWE Installation Manual Vehicle Remote Start System 128-9296 2/24 2 Before You Begin PROFESSIONAL INSTALLATION IS STRONGLY RECOMMENDED Roll down window to avoid locking the keys in the vehicle during installation Avoid mounting components or routing wires near hot surfaces or near moving parts like the steering wheel as it may prevent proper operation of the vehicle Tape or loom wires under the hood and dash for protection as well appearance Use grommets when routing wires through metal surfaces to pre- vent chafing and shorting Use a Digital Multi Meter for testing and verifying circuits. DO NOT USE A "TEST LIGHT" OR "COMPUTER SAFE PROBE" as these can set off air bags or damage sensitive vehicle computers and electronics For technical support go to www.avxtech1.com or call 1 800 225 6074 FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation. Warning! Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment NOTE:The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment 128-9296 3/24 3 12 Pin Main Wiring Harness #1124295 1 Green/Orange Tachometer Input 2 Green/Yellow Glow Plug Input 3 Green Door Unlock 4 Brown/Black (+) Inhibit /Shutdown To Brake Switch 5 Brown (+) Inhibit / Shutdown To Brake Switch 6 Gray (-) Inhibit Neutral Start Switch 7 Black/Yellow Pulse During Crank Output (-) 8 Black/Red Pulse After Shut Down Output (-) 9 Black/Blue Pulse Before Start Output (-) 10 Black/LT. Green Pulse After Start Output (-) 11 LT. Blue Ground While Running Output (-) 12Gray/Black (-) Inhibit / Shutdown To Hood Switch 128-9296 4/24 4 6 Pin Power / Start Harness #1123742 4 Pin 2nd Main Harness #1124294 6 Pin Antenna Harness #1124293 1 Blue Ignition 1 (+) 2 Red/White Battery 1 - 12V (+) 3 Green Ignition 2 (+) 4 Purple Accessory (+) 5 Red Battery 2 - 12V (+) 6 Yellow Starter Output 1 Black Chassis Ground 2 White/Red Parking Light Relay Input 3 Yellow/Black To Controlling Alarms Ignition Input 4 White Parking Light Relay Output 1 Red + 5 VDC 2 Green RX 3 Black Ground 4 Gray Valet Enable 5 Blue LED Cathode 6 Blue TX 128-9296 5/24 5 This Remote Start is to be used in vehicles with AUTOMATIC TRANSMISSIONS only! Although this system is a sophisticated device with many advanced features, IT MUST NOT be installed into a vehicle with manually operated transmission. Doing so may result in serious personal injury and property damage! INSTALLATION OF THE MAJOR COMPONENTS: CONTROL MODULE: PART # 1365394 Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting location selected must be within 24" of the ignition switch wiring harness to allow connection of the 6 pin main wiring harness. Be certain that the chosen location will not interfere with proper operation of the vehicle. Avoid mounting the module to or routing the wiring around the steering shaft/column, as the module or wiring may wrap around or block the steering wheel preventing proper control of the vehicle. The module will be secured after all wiring is completed which will allow complete access until the job is done. Do Not Mount The Module In The Engine Compartment, as it is not waterproof. HOOD PIN SWITCH: PART # 1363699 The pin switch included in this package is intended for protecting the hood area of the vehicle. In all cases, the switch must be mounted to a grounded metal surface. When the pin switch is activated, (hood open), it will supply a ground to the input wire activating the alarm. In addition, the hood switch is required for the safety shut down of the remote start unit. If the vehicle is being worked on, this hood switch prevents the remote start activation even if the RF command to start is issued. This switch must be installed in all applications. Failure to do so may result in personal injury or property damage. THE PUSH-BUTTON PROGRAM SWITCH/LED/RECEIVER/ANTENNA ASSEMBLY: PART # 1181252 The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dash board for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception. Special considerations must be made for windshield glass as some newer vehicles utilize a metallic shielded window glass that will inhibit or restrict RF reception. In these vehicles, route the antenna toward a rear window location for best reception. Secure the antenna with double stick tape provided. 128-9296 6/24 6 IMPORTANT! DO NOT PLUG THE EIGHT PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT HA…

Text truncated - open the document above for the full version.

775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (current) 2.0 3.0 Jan-31-2012 SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 3.0

775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0

Report No.：14A072107R-FR FCC ID： ELVATRND Page 22 of 25 Interocean EMC Technology Corp. Test Report 7 Photographs of EUT Front View of EUT Rear View of EUT Report No.：14A072107R-FR FCC ID： ELVATRND Page 23 of 25 Interocean EMC Technology Corp. Test Report FCC ID

FCC ID:ELVATRND P/N:TRXFSK FELIX MT-11020 MTF02010*1 0.2 C  B  D  NTABA0B0*1/NTABA0C0*1 YYS VICTOR BODY MATERIAL : CLEAR PC + UV BLACK(CLEAR PC)

Report No.：14A072107R-FR FCC ID： ELVATRND Page 24 of 25 Interocean EMC Technology Corp. Test Report Inner View of EUT Antenna Location Report No.：14A072107R-FR FCC ID： ELVATRND Page 25 of 25 Interocean EMC Technology Corp. Test Report Front View of Main Board Rear View of Main Board

Report No.：14A072107R-FR FCC ID： ELVATRND Page 1 of 25 Interocean EMC Technology Corp. Test Report CFR 47 FCC Part 15.231 TEST REPORT Product： Transceiver Trade Name： N/A Model Number： TRXFSK FCC ID： ELVATRND Prepared for Nutek Corporation NO. 167, Lane 235, Bauchiau Rd., Xindian District, New Taipei City 23145, Taiwan TEL.： +886 2 2918 9478 FAX.： +886 2 2917 9069 Prepared by Interocean EMC Technology Corp. No. 5-2, Lin 1, Tin-Fu, Lin-Kou Dist., New Taipei City, Taiwan 244, R.O.C. TEL.: +886 2 2600 6861 FAX.: +886 2 2600 6859 Remark: The test report consists of 25 pages in total. It shall not be reproduced except in full, without the written approval of IETC. This document may be altered or revised by IETC only, and shall be noted in the revision section of the document. The test result in the report is only subjected to the test sample. Report No.：14A072107R-FR FCC ID： ELVATRND Page 2 of 25 Interocean EMC Technology Corp. Test Report Statement of Compliance Applicant: Nutek Corporation Manufacturer: Nutek Corporation Product: Transceiver Model No.: TRXFSK Tested Power Supply: DC 12V Date of Final Test: Jul. 22, 2014 Configuration of Measurements and Standards Used： FCC Rules and Regulations Part 15 Subpart C 1. The result of the testing report relate only to the item tested. 2. The testing report shall not be reproduced expect in full, without the written approval of IETC. Report Issued: 2014/08/01 Project Engineer: Approved: Elli Chang Jerry Liu Report No.：14A072107R-FR FCC ID： ELVATRND Page 3 of 25 Interocean EMC Technology Corp. Test Report Table of Contents 1 Summary of Measurement 4 2 General Information 5 2.1 Description of Equipment Under Test 5 2.2 Details of Tested Peripheral Equipment 6 2.3 Test Facility 7 3 Test Specifications 8 3.1 Test Standard 8 3.2 Test Step of EUT 8 3.3 Test Equipment 9 4 Radiated Emission Test 10 4.1 Limits 10 4.2 Calculation of Average Factor 11 4.3 Configuration of Measurement 15 4.4 Test Procedure 15 4.5 Test Result 15 5 Emission Bandwidth 18 5.1 Limits 18 5.2 Test Result 18 6 Photographs of Test 20 6.1 Radiated Emission Measurement 20 7 Photographs of EUT 22 Report No.：14A072107R-FR FCC ID： ELVATRND Page 4 of 25 Interocean EMC Technology Corp. Test Report 1 Summary of Measurement Report Clause Test Parameter Reference Document CFR47 Part15 Results 4 Timing requirement §15.231(a) Pass 4 Radiated Emission §15.231(b), 15.209 Pass 5 Emission Bandwidth §15.231(c) Pass Report No.：14A072107R-FR FCC ID： ELVATRND Page 5 of 25 Interocean EMC Technology Corp. Test Report 2 General Information 2.1 Description of Equipment Under Test Product : Transceiver Model Number : TRXFSK Applicant : Nutek Corporation NO. 167, Lane 235, Bauchiau Rd., Xindian District, New Taipei City 23145, Taiwan Manufacturer : Nutek Corporation NO. 167, Lane 235, Bauchiau Rd., Xindian District, New Taipei City 23145, Taiwan Power Supply : DC 12V Operating Frequency : 433.92MHz Type of Modulation : FSK Antenna Description : This device uses Helix antenna. The antenna is integral to the device, thereby meeting the requirement of FCC 15.203. Date of Test : Jul. 01 ~ 22, 2014 Additional Description : 1) The Model Number “TRXFSK” is representative selected in the test and included in this report. 2) For more detail specification about EUT, please refer to the user’s manual. Report No.：14A072107R-FR FCC ID： ELVATRND Page 6 of 25 Interocean EMC Technology Corp. Test Report 2.2 Details of Tested Peripheral Equipment 2.2.1 Battery (DC 12V) Model Number : MF75D23R Manufacturer : GLOBAL Report No.：14A072107R-FR FCC ID： ELVATRND Page 7 of 25 Interocean EMC Technology Corp. Test Report 2.3 Test Facility Site Description : OATS 1 Name of Firm : Interocean EMC Technology Corp. Company web : http://www.ietc.com.tw Location : No. 5-2, Lin 1, Tin-Fu, Lin-Kou Dist., New Taipei City, Taiwan 244, R.O.C. Site Filing :  Federal Communication Commissions – USA Registration No.: 96399 (OATS 1, 2, 3 & Chamber 3) Designation No.: TW1020  Industry Canada (IC) OUR FILE: 46405-4437 Registration No. (OATS 1): Site# 4437A-1 Registration No. (OATS 3): Site# 4437A-3 Registration No. (Chamber 3): Site# 4437A-5 Registration No. (OATS 5): Site# 4437A-6  Voluntary Control Council for Interference by Information Technology Equipment (VCCI) – Japan Member No.: 1349 Registration No. (Conducted Room): C-1094 Registration No. (Conducted Room): T-1562 Registration No. (OATS 1): R-1040; G-274 Registration No. (OATS 2): R-1041 Site Accreditation :  Bureau of Standards and Metrology and Inspection (BSMI) – Taiwan, R.O.C. Accreditation No.: SL2-IN-E-0026 for CNS13438 / CISPR 22 SL2-IN-E-0026 for CNS14757-2 / IEC 62040-2 SL2-R1-E-0026 for CNS13439 / CISPR 13 SL2-R2-E-0026 for CNS13439 / CISPR 13 SL2-A1-E-0026 for CNS13783-1 / CISPR 14-1 SL2-L1-E-0026 for CNS 14115 / CISPR 15  Taiwan Accreditation Foundation (TAF) Accreditation No.: 1113  Vehicle Safety Certification Center (VSCC) Approval No.: TW16-11-0  TüV NORD Certificate No: TNTW0801R-04  Nemko Authorisation No: AeLA 011 Authorisation No: ELA 181 Report No.：14A072107R-FR FCC ID： ELVATRND Page 8 of 25 Interocean EMC Technology Corp. Test Report 3 Test Specifications 3.1 Test Standard The EUT was performed according to FCC Part 15 Subpart C Section 15.231 procedure and setup followed by ANSI C63.4, 2003 requirements. 3.2 Test Step of EUT 3.2.1 Setup the fixture to EUT for power supplying. 3.2.2 Turn on the power of all equipment. 3.2.3 Let the EUT continuous transmission. Executed the test. Report No.：14A072107R-FR FCC ID： ELVATRND Page 9 of 25 Interocean EMC Technology Corp. Test Report 3.3 Test Equipment Instrument Manufacturer Model Serial No. Next Cal. Date Spectrum Analyzer R&S FSP40 100478 2015/06/02 Preamplifier Agilent 8449B 3008A01434 2015/05/07 Preamplifier Agilent 83050A 3950A00225 2014/09/08 Horn Antenna Schwarzbeck BBHA 9120 9120D-583 2015/05/13 Horn Antenna Schwarzbeck BBHA 9170 213 2014/07/24 Cable HARBOUR 27478LL142 CBL22 2015/01/01 EMI Test Receiver Rohde & Sc…

Text truncated - open the document above for the full version.

Report No.：14A072107R-FR FCC ID： ELVATRND Page 20 of 25 Interocean EMC Technology Corp. Test Report 6 Photographs of Test 6.1 Radiated Emission Measurement Front View (Frequency below 1GHz) Rear View (Frequency below 1GHz) Report No.：14A072107R-FR FCC ID： ELVATRND Page 21 of 25 Interocean EMC Technology Corp. Test Report Front View (Frequency above 1GHz) Rear View (Frequency above 1GHz)