EMJDDGRF67GBReceiver

Important Information Federal Communications Commission Declaration of Conformity Receiver (build in AIO) FCC ID: EMJDDGRF67GB Keyboard FCC ID: EMJKKBRF6711 Touchpad FCC ID: EMJPTPRFGB11 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help." This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Product Model Receiver (Build in ALL-IN-ONE PC) DGRF67GB This device is intended only for OEM integrators under the following conditions: 1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2. The transmitter module may not be co-located with any other transmitter or antenna. 3. Module approval valid only when the module is installed in the tested host or compatible series of host As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: EMJDDGRF67GB”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Canada Notice for Licence‐Exempt Radio Apparatus Receiver (build in AIO) IC: 4251A-DDGRF67GB Keyboard IC: 4251A-KKBRF6711 Touchpad IC: 4251A-PTPRFGB11 This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: 1) le dispositif ne doit pas produire de brouillage préjudiciable, et 2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. 3) Module approval valid only when the module is installed in the tested host or compatible series of host As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) L'antenne doit être…

Text truncated - open the document above for the full version.

esc tabcapsshiftctrl ctrl fn alt alt insert delete backspace enter shift = + {} |  : ? > < 0 ) 9 ( & % $ # @ ! ~ 8 7 6 5 4 3 2 1 Q ASDFGHJKL M N B V C X Z ; /.,  WE RT Y U I OP [ ] \ ` * ^ - _ F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 printscr OK esc tabcapsshiftctrl ctrl fn alt alt insert delete backspace enter shift = + {} |  : ? > < 0 ) 9 ( & % $ # @ ! ~ 8 7 6 5 4 3 2 1 Q ASDFGHJKL M N B V C X Z ; /.,  WE RT Y U I OP [ ] \ ` * ^ - _ F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 printscr

OK

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Date: April 17, 2012 Federal Communications Commission Authorization and Evaluation Division Subject: Short-term confidentiality request regarding application for certification of FCC ID: EMJDDGRF67GB Pursuant to DA 04-1705 of the Commission’s public notice, we request short-term confidential treatment for the following information until July 31, 2012 in order to ensure sensitive business information remains confidential until the actual marketing of the device. External Photos Test setup photos User’s Manual Internal Photos Sincerely yours, -------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Date: April 16, 2012 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request FCC ID: EMJDDGRF67GB Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Power of Attorney Date: April 16, 2012 To whom it may concern: We, the undersigned PRIMAX ELECTRONICS LTD. hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan Branch) of Taiwan to act on our behalf in all matters relating to all processes required in the FCC Part 15C approval and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan Branch on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, -------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT Model: CA27 Page 2 Model: CA24 Page 3 Page 4

LABEL LOCATION Label Location LABEL LOCATION Label Location

Model: DGRF67GB FCC ID: EMJDDGRF67GB IC: 4251A‐DDGRF67GB

Page 5

FCC ID: EMJDDGRF67GB Report No.: RF120322D15 Operational Description The transmitter of the EUT (Receiver) is powered by 5Vdc from host equipment. The type of antenna is Printed antenna. The output power of this device is very low. Under normal use condition, the transmitter and the receiver are quite close, so high EIRP power is neither necessary nor allowed because of interference.

Report No.: RF120322D15 1 Report Format Version 4.2.0 FCC TEST REPORT REPORT NO.: RF120322D15 MODEL NO.: DGRF67GB FCC ID: EMJDDGRF67GB RECEIVED: Mar. 15, 2012 TESTED: Mar. 15 ~ Apr. 13, 2012 ISSUED: Apr. 13, 2012 APPLICANT: PRIMAX ELECTRONICS LTD. ADDRESS: No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB LOCATION: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C. ) This test report consists of 36 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF120322D15 2 Report Format Version 4.2.0 Table of Contents RELEASE CONTROL RECORD..............................................................................3 1. CERTIFICATION.........................................................................................4 2. SUMMARY OF TEST RESULTS.................................................................5 2.1 MEASUREMENT UNCERTAINTY...............................................................5 3. GENERAL INFORMATION..........................................................................6 3.1 GENERAL DESCRIPTION OF EUT............................................................6 3.2 DESCRIPTION OF TEST MODES..............................................................7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST.........................................7 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL:.............8 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS...........................10 3.4 DESCRIPTION OF SUPPORT UNITS......................................................10 4. TEST TYPES AND RESULTS...................................................................11 4.1 CONDUCTED EMISSION MEASUREMENT............................................11 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT..........................11 4.1.2 TEST INSTRUMENTS..............................................................................11 4.1.3 TEST PROCEDURES...............................................................................12 4.1.4 DEVIATION FROM TEST STANDARD.....................................................12 4.1.5 TEST SETUP............................................................................................12 4.1.6 EUT OPERATING CONDITIONS..............................................................13 4.1.7 TEST RESULTS........................................................................................14 4.2 RADIATED EMISSION MEASUREMENT.................................................18 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT...............................18 4.2.2 TEST INSTRUMENTS..............................................................................19 4.2.3 TEST PROCEDURES...............................................................................20 4.2.4 DEVIATION FROM TEST STANDARD.....................................................20 4.2.5 TEST SETUP............................................................................................21 4.2.6 EUT OPERATING CONDITIONS..............................................................21 4.2.7 TEST RESULTS........................................................................................22 4.3 BAND EDGES MEASUREMENT..............................................................31 4.3.1 LIMITS OF BAND EDGES MEASUREMENT............................................31 4.3.2 TEST INSTRUMENTS..............................................................................31 4.3.3 TEST PROCEDURE.................................................................................31 4.3.4 DEVIATION FROM TEST STANDARD.....................................................31 4.3.5 EUT OPERATING CONDITION................................................................31 4.3.6 TEST RESULTS........................................................................................31 5. PHOTOGRAPHS OF THE TEST CONFIGURATION................................34 6. INFORMATION ON THE TESTING LABORATORIES..............................35 7. APPENDIX A – MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB.....................................................36 Report No.: RF120322D15 3 Report Format Version 4.2.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED RF120322D15 Original release Apr. 13, 2012 Report No.: RF120322D15 4 Report Format Version 4.2.0 1. CERTIFICATION PRODUCT: Receiver BRAND NAME: VIZIO MODEL NO.: DGRF67GB APPLICANT: PRIMAX ELECTRONICS LTD. TESTED: Mar. 15 ~ Apr. 13, 2012 TEST ITEM: ENGINEERING SAMPLE STANDARDS: FCC Part 15, Subpart C (Section 15.249) ANSI C63.10-2009 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: ( Celia Chen / Senior Specialist ) APPROVED BY : , DATE: ( Ken Liu / Manager ) Report No.: RF120322D15 5 Report Format Version 4.2.0 2. SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC Part 15, Subpart C (Section 15.249) STANDARD PARAGRAPH TEST TYPE RESULT REMARK 15.207 Conducted Emission Test PASS Meet the requirement of limit. Minimum passing margin is -14.34dB at 4.59766MHz. 15.209 15.249 15.249 (d) Radiated Emission Test Band Edge Measurement Limit: 50dB less than the peak value of fundamental frequency …

Text truncated - open the document above for the full version.

Report No.: RF120322D15 1 Report Format Version 4.2.0 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST – Mode A Report No.: RF120322D15 2 Report Format Version 4.2.0 CONDUCTED EMISSION TEST – Mode B Report No.: RF120322D15 3 Report Format Version 4.2.0 RADIATED EMISSION TEST – Mode A Report No.: RF120322D15 4 Report Format Version 4.2.0 RADIATED EMISSION TEST – Mode B