EMJDN111-301AWireless Dongle

2.4G Nano Laser Mouse User’s Quick Guide 2 Notice: Federal Communications Commission (FCC) requirements, Part 15 This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or 3 television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes of modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. 4 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. 5 CE Declaration Of Conformity Hereby, the manufacturer, declares that this s Mouse Wireless Presenter in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Essential requirements - Article 3 Protection requirements for health and safety - Article 3.1a --Testing for electric safety according to EN 60950 has been conducted. These are considered relevant and sufficient. Protection requirements for electromagnetic compatibility -Article 3.1b --Testing for electromagnetic compatibility according to 6 EN 301 489-1 and EN 301 489-3 has been conducted. These are considered relevant and sufficient Effective use of the radio spectrum -Article 3.2 --Testing for radio test suites according to EN 300 440-2 has been conducted. These are considered relevant and sufficient. Congratulations on your purchase of this 2.4G Nano Laser Mouse. Please carefully read the User’s Quick Guide to learn about the installation and the powerful functions of your new Laser Mouse. 7 Contents of the Package 9 2.4G Laser Mouse 9 Nano Dongle 9 One AA Battery 9 Mouse Driver CD 9 User’s Quick Guide Nano Dongle Battery Release Button Release Button Release Button 8 Scrolling Wheel with Tilt Functionality Battery Indication 9 Install Hardware z Push the release button to open the battery door z Take off the Nano Dongle from battery compartment z Close the battery door z Connect the Nano Dongle to the computer. Switch on the power switch on the back 10 Install Driver Notice:The driver supports Windows XP and Vista 1. The Set-up of driver in Driver CD could be automatically once plugged in. In case it doesn’t work, please go to Step 2 2. Insert the driver CD to your computer Æ Double click “Setup.exe” and follow the setup instructions to complete the driver installation. 3. A Mouse Setting icon will appear on the task bar of Windows. 11 Battery Notice z The LED indicator on the mouse will turn on as solid green ever since your power on whenever the mouse is in battery ok status z The LED indicator on the mouse will become blinking red with the frequency of 1 time at 1 second while the mouse is low battery. Please change the batteries immediately. z Press any button to wake up the mouse while the mouse is in the standby mode.

Power of Attorney Date: February 25, 2008 To whom it may concern: We, the undersigned PRIMAX ELECTRONICS LTD. hereby authorize Advance Data Technology Corporation (ADT) of Taiwan to act on our behalf in all matters relating to all processes required in the FCC Part 15C approval and any communication needed with the national authority. Any and all acts carried out by ADT on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

Date: February 25, 2008 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request FCC ID: EMJDN111-301A Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT

? 1 4 , 4 0 6 , 0 0 8 6 , 3 3

FCC ID: EMJDN111-301A FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Label

Page 2 Page 3

FCC ID: EMJDN111-301A Report No.: RF970128A07 Operational Description The transceiver of the EUT (Wireless Dongle) is powered 5Vdc from host equipment. The type of antenna is Chip antenna. The output power of this device is very low. Under normal use condition, the transmitter and the receiver are quite close, so high EIRP power is neither necessary nor allowed because of interference.

Report No: SA970128A07 1 RF EXPOSURE REPORT REPORT NO.: RF970128A07 MODEL NO.: N111-301A ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT : PRIMAX ELECTRONICS LTD. ADDRESS : No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY : Advance Data Technology Corporation LAB ADDRESS : No. 47, 14 th Ling, Chia Pau Tsuen, Linko Hsiang 244, Taipei Hsien, Taiwan, R.O.C. Report No: SA970128A07 2 Conclusion No Evaluation Required if power is below this threshold: F(GHz) mW Low 2.402 High 2.474 24.61 Maximum measured transmitter power: Pout (dBm) Pout (mW) Conducted Power -0.78 0.836 EIRP Power 1.72 1.486 *Note: The antenna is Chip antenna with 2.5dBi gain Threshold for no SAR evaluation is 24.61mW Transmitter power is 1.486mW Conclusion: No SAR evaluation required since Transmitter Pout is below FCC threshold

Report No.: RF970128A07 1 Report Format Version 2.0.6 FCC TEST REPORT REPORT NO.: RF970128A07 MODEL NO.: N111-301A RECEIVED: Jan. 28, 2008 TESTED: Jan. 30 ~ Feb. 1, 2008 ISSUED: Feb. 20, 2008 APPLICANT: PRIMAX ELECTRONICS LTD. ADDRESS: No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB LOCATION: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. This test report consists of 42 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by TAF, A2LA or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF970128A07 2 Report Format Version 2.0.6 Table of Contents 1. CERTIFICATION..........................................................................................4 2. SUMMARY OF TEST RESULTS..................................................................5 2.1 MEASUREMENT UNCERTAINTY...............................................................5 3. GENERAL INFORMATION..........................................................................6 3.1 GENERAL DESCRIPTION OF EUT............................................................6 3.2 DESCRIPTION OF TEST MODES..............................................................7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST.........................................7 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL:.............8 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS.............................9 3.4 DESCRIPTION OF SUPPORT UNITS........................................................9 4. TEST TYPES AND RESULTS....................................................................10 4.1 CONDUCTED EMISSION MEASUREMENT............................................10 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT..........................10 4.1.2 TEST INSTRUMENTS..............................................................................10 4.1.3 TEST PROCEDURES...............................................................................11 4.1.4 DEVIATION FROM TEST STANDARD.....................................................11 4.1.5 TEST SETUP ...........................................................................................11 4.1.6 EUT OPERATING CONDITIONS..............................................................12 4.1.7 TEST RESULTS........................................................................................13 4.2 RADIATED EMISSION MEASUREMENT.................................................15 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT...............................15 4.2.2 TEST INSTRUMENTS..............................................................................16 4.2.3 TEST PROCEDURES...............................................................................17 4.2.4 DEVIATION FROM TEST STANDARD.....................................................17 4.2.5 TEST SETUP ...........................................................................................18 4.2.6 EUT OPERATING CONDITIONS..............................................................18 4.2.7 TEST RESULTS........................................................................................19 4.3 6DB BANDWIDTH MEASUREMENT........................................................24 4.3.1 LIMITS OF 6DB BANDWIDTH MEASUREMENT......................................24 4.3.2 TEST INSTRUMENTS..............................................................................24 4.3.3 TEST PROCEDURE.................................................................................24 4.3.4 DEVIATION FROM TEST STANDARD.....................................................24 4.3.5 TEST SETUP ...........................................................................................24 4.3.6 EUT OPERATING CONDITIONS..............................................................24 4.3.7 TEST RESULTS........................................................................................25 4.4 MAXIMUM PEAK OUTPUT POWER........................................................27 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT.........27 4.4.2 INSTRUMENTS.........................................................................................27 4.4.3 TEST PROCEDURES...............................................................................27 4.4.4 DEVIATION FROM TEST STANDARD.....................................................27 4.4.5 TEST SETUP ...........................................................................................28 4.4.6 EUT OPERATING CONDITIONS..............................................................28 4.4.7 TEST RESULTS........................................................................................28 4.5 POWER SPECTRAL DENSITY MEASUREMENT....................................31 Report No.: RF970128A07 3 Report Format Version 2.0.6 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT..................31 4.5.2 TEST INSTRUMENTS..............................................................................31 4.5.3 TEST PROCEDURE.................................................................................31 4.5.4 DEVIATION FROM TEST STANDARD.....................................................31 4.5.5 TEST SETUP ...........................................................................................31 4.5.6 EUT OPERATING CONDITION................................................................31 4.5.7 TEST RESULTS........................................................................................32 4.6 BAND EDGES MEASUREMENT..............................................................34 4.6.1 LIMITS OF BAND EDGES MEASUREMENT............................................34 4.6.2 TEST INSTRUMENTS.......…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST