EMJM2AC01Wireless Presentation Mouse

VGP-WMS50 2-684-362-11(1) VGP-WMS50 2-684-362-11(1) English WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. Owner’s Record The model number and the serial number are located on the bottom of the mouse. Record the serial number in the space provided below. Refer to this number whenever you call your Sony dealer regarding this product. Model No. VGP-WMS50 Serial No. ____________________ For customers in the U.S.A. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help. The shielded interface cable recommended in this manual must be used with this equipment in order to comply with the limits for a digital device pursuant to subpart B of Part 15 of the FCC Rules. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. For questions regarding your product or for the Sony Service Center nearest you, call 1-888-476-6972 in the United States or 1-800-961-7669 in Canada. The number below is for FCC related matters only. Declaration of Conformity Trade Name: SONY Model No.: VGP-WMS50 Responsible Party: Sony Electronics Inc. Address: 16450 W. Bernardo Dr., San Diego, CA 92127 U.S.A. Telephone No.: 858-942-2230 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: These products comply with FCC radiation exposure limits set forth for uncontrolled equipment and meet the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. These products have very low levels of RF energy that it is deemed to comply without testing of specific absorption ratio (SAR). For customers in Canada This Class B digital apparatus complies with Canadian ICES-003. The term “IC:” before the radio certification number only signifies that the Industry Canada technical specifications were met. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. IC Exposure of Humans to RF Fields The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website: www.hc-sc.gc.ca/rpb. •VAIO and are trademarks of Sony Corporation. •Microsoft, Windows and PowerPoint ® are registered trademarks of Microsoft Corporation in the United States and/or other countries. •All other names of systems, products, and services are trademarks of their respective owners. In this manual, the ™ or ® marks are not specified. In this manual, Microsoft ® Windows ® 2000 Professional is referred to as Windows 2000. In this manual, Microsoft ® Windows ® Millennium Edition is referred to as Windows Me. In this manual, Microsoft ® Windows ® XP Home Edition, Microsoft ® Windows ® XP Professional and Microsoft ® Windows ® XP Media Center Edition are referred to as Windows XP. Before Use The Wireless Presentation Mouse is a USB mouse specifically designed for Sony VIAO ® computers* and IBM PC/AT compatible computers with USB ports and pre-installed with Windows XP. *This includes Windows XP Ready PCs upgraded with the Windows XP Upgrade Program distributed by Sony Corporation. This product features a presentation mode, enabling use not only as a wireless mouse but also as a presentation remote, allowing for pointer movement and slideshow direction from a distance. Mouse mode: Use as a wireless mouse. Presentation mode: Use as a pointing device, ideal for presentations. Notes •Inserting the wireless receiver into the computer’s USB port may disable neighboring USB ports. •Operation is not guaranteed for every computer that meets the above conditions. •Operation is not guaranteed for home-built computers, white box PCs, and computers with OS upgrades and multi-boot systems. Names of Parts Wireless mouse *Hereafter referred to as ??Scroll Pointer??. Wireless receiver Preparations Inserting batteries into the mouse 1Set the power/mode switch located on the bottom of the mouse to OFF. 2Open the battery compartment cover. 3Insert the two supplied IEC R6 (size AA) batteries with the correct + - orientation. Note To prevent battery fluid leaks and damage, observe the following precautions. •Insert the batteries with the correct + - orientation. •Do not charge dry cell batteries. •Do not mix old and new batte…

Text truncated - open the document above for the full version.

Date: 2005/7/6 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request FCC ID: EMJM2AC01 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

Power of Attorney To whom it may concern: We, the undersigned PRIMAX ELECTRONICS LTD. hereby authorize Advance Data Technology Corporation (ADT) of Taiwan to act on our behalf in all matters relating to all processes required in the FCC Part 15C approval and any communication needed with the national authority. Any and all acts carried out by ADT on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

FCC ID: EMJM2AC01 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. LABEL

Page 3 Page 4 Page 5 Page 6 Page 7

FCC ID: EMJM2AC01 Report No.: RF940606A05 Operational Description The transmitter of the EUT (WIRELESS PRESENTATION MOUSE) is powered by 3V batteries. The type of antenna is Printed antenna. The output power of this device is very low. Under normal use condition, the transmitter and the receiver are quite close, so high EIRP power is neither necessary nor allowed because of interference.

FCC ID: EMJM2AC01 Report No.: RF940606A051Report Format Version 2.0.2 FCC TEST REPORT REPORT NO.: RF940606A05 MODEL NO.: VGP-WMS50 RECEIVED: June 6, 2005 TESTED: June 10 ~ 16, 2005 ISSUED: July 7, 2005 APPLICANT: PRIMAX ELECTRONICS LTD. ADDRESS: No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan. R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 35 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA FCC ID: EMJM2AC01 Report No.: RF940606A052Report Format Version 2.0.2 Table of Contents 1.CERTIFICATION...........................................................................................4 2.SUMMARY OF TEST RESULTS...................................................................5 2.1MEASUREMENT UNCERTAINTY................................................................5 3.GENERAL INFORMATION............................................................................6 3.1GENERAL DESCRIPTION OF EUT..............................................................6 3.2DESCRIPTION OF TEST MODES................................................................7 3.2.1CONFIGURATION OF SYSTEM UNDER TEST...........................................8 3.2.2TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL:...............9 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS.............................10 3.4DESCRIPTION OF SUPPORT UNITS........................................................10 4.TEST TYPES AND RESULTS.....................................................................11 4.1CONDUCTED EMISSION MEASUREMENT..............................................11 4.2RADIATED EMISSION MEASUREMENT...................................................11 4.2.1LIMITS OF RADIATED EMISSION MEASUREMENT.................................11 4.2.2TEST INSTRUMENTS................................................................................12 4.2.3TEST PROCEDURES.................................................................................13 4.2.4DEVIATION FROM TEST STANDARD.......................................................13 4.2.5TEST SETUP..............................................................................................14 4.2.6EUT OPERATING CONDITIONS................................................................14 4.2.7TEST RESULTS..........................................................................................15 4.36dB BANDWIDTH MEASUREMENT..........................................................19 4.3.1LIMITS OF 6dB BANDWIDTH MEASUREMENT........................................19 4.3.2TEST INSTRUMENTS................................................................................19 4.3.3TEST PROCEDURE...................................................................................19 4.3.4DEVIATION FROM TEST STANDARD.......................................................19 4.3.5TEST SETUP..............................................................................................19 4.3.6EUT OPERATING CONDITIONS................................................................19 4.3.7TEST RESULTS..........................................................................................20 4.4MAXIMUM PEAK OUTPUT POWER..........................................................22 4.4.1LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT...........22 4.4.2INSTRUMENTS..........................................................................................22 4.4.3TEST PROCEDURES.................................................................................23 4.4.4DEVIATION FROM TEST STANDARD.......................................................23 4.4.5TEST SETUP..............................................................................................23 4.4.6EUT OPERATING CONDITIONS................................................................23 4.4.7TEST RESULTS..........................................................................................24 4.5POWER SPECTRAL DENSITY MEASUREMENT......................................26 4.5.1LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT...................26 4.5.2TEST INSTRUMENTS................................................................................26 4.5.3TEST PROCEDURE...................................................................................26 4.5.4DEVIATION FROM TEST STANDARD.......................................................26 4.5.5TEST SETUP..............................................................................................26 4.5.6EUT OPERATING CONDITION..................................................................26 FCC ID: EMJM2AC01 Report No.: RF940606A053Report Format Version 2.0.2 4.5.7TEST RESULTS..........................................................................................27 4.6BAND EDGES MEASUREMENT................................................................29 4.6.1LIMITS OF BAND EDGES MEASUREMENT..............................................29 4.6.2TEST INSTRUMENTS................................................................................29 4.6.3TEST PROCEDURE...................................................................................29 4.6.4DEVIATION FROM TEST STANDARD.......................................................29 4.6.5EUT OPERATING CONDITION..................................................................29 4.6.6TEST RESULTS..........................................................................................30 4.7ANTEN…

Text truncated - open the document above for the full version.

FCC ID: EMJM2AC01 Report No.: RF940606A0534Report Format Version 2.0.2 5. PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST