EMJM2AX01Mouse

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Date: 2007/02/06 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request FCC ID: EMJM2AX01 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

Power of Attorney Date: 2007/02/06 To whom it may concern: We, the undersigned PRIMAX ELECTRONICS LTD. hereby authorize Advance Data Technology Corporation (ADT) of Taiwan to act on our behalf in all matters relating to all processes required in the FCC Part 15C approval and any communication needed with the national authority. Any and all acts carried out by ADT on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT

EMJM2AX01 1.5V 40mA 1;1

FCC ID: EMJM2AX01 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. LABEL

Page 2 Page 3 Page 4 Page 5

FCC ID: EMJM2AX01 Report No.: RF960125A06 Operational Description The transmitter of the EUT (Mouse) is powered by 1.5Vdc from battery. The type of antenna is monopole antenna. The output power of this device is very low. Under normal use condition, the transmitter and the receiver are quite close, so high EIRP power is neither necessary nor allowed because of interference.

Report No: SA960125A06 1 RF EXPOSURE REPORT REPORT NO.: SA960125A06 MODEL NO.: N101P-401B, 00052491, 98505 ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT : PRIMAX ELECTRONICS LTD. ADDRESS : No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY : Advance Data Technology Corporation LAB ADDRESS : No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. Report No: SA960125A06 2 Conclusion No Evaluation Required if power is below this threshold: F(GHz) mW Low 2.402 High 2.474 24.61 Maximum measured transmitter power: Pout (dBm) Pout (mW) Conducted Power 0.94 1.242 EIRP Power -2.24 0.597 *Note: The antenna is monopole antenna with –3.18dBi gain Threshold for no SAR evaluation is 24.61mW Transmitter power is 1.242mW Conclusion: No SAR evaluation required since Transmitter Pout is below FCC threshold

Report No.: RF960125A06 1 Report Format Version 2.0.5 FCC TEST REPORT REPORT NO.: RF960125A06 MODEL NO.: N101P-401B, 00052491, 98505 RECEIVED: Jan. 25, 2007 TESTED: Jan. 25 ~ Feb. 2, 2007 ISSUED: Feb. 6, 2007 APPLICANT: PRIMAX ELECTRONICS LTD. ADDRESS: No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB LOCATION: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. This test report consists of 36 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF960125A06 2 Report Format Version 2.0.5 Table of Contents 1. CERTIFICATION..........................................................................................4 2. SUMMARY OF TEST RESULTS..................................................................5 2.1 MEASUREMENT UNCERTAINTY...............................................................5 3. GENERAL INFORMATION..........................................................................6 3.1 GENERAL DESCRIPTION OF EUT............................................................6 3.2 DESCRIPTION OF TEST MODES..............................................................7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST.........................................8 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL:.............9 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS...........................10 3.4 DESCRIPTION OF SUPPORT UNITS......................................................10 4. TEST TYPES AND RESULTS....................................................................11 4.1 CONDUCTED EMISSION MEASUREMENT............................................11 4.2 RADIATED EMISSION Measurement.......................................................11 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT...............................11 4.2.2 TEST INSTRUMENTS..............................................................................12 4.2.3 TEST PROCEDURES...............................................................................13 4.2.4 DEVIATION FROM TEST STANDARD.....................................................13 4.2.5 TEST SETUP ...........................................................................................14 4.2.6 EUT OPERATING CONDITIONS..............................................................14 4.2.7 TEST RESULTS........................................................................................15 4.3 6dB BANDWIDTH MEASUREMENT.........................................................19 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT......................................19 4.3.2 TEST INSTRUMENTS..............................................................................19 4.3.3 TEST PROCEDURE.................................................................................19 4.3.4 DEVIATION FROM TEST STANDARD.....................................................19 4.3.5 TEST SETUP ...........................................................................................19 4.3.6 EUT OPERATING CONDITIONS..............................................................19 4.3.7 TEST RESULTS........................................................................................20 4.4 MAXIMUM PEAK OUTPUT POWER........................................................22 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT.........22 4.4.2 INSTRUMENTS.........................................................................................22 4.4.3 TEST PROCEDURES...............................................................................22 4.4.4 DEVIATION FROM TEST STANDARD.....................................................22 4.4.5 TEST SETUP ...........................................................................................23 4.4.6 EUT OPERATING CONDITIONS..............................................................23 4.4.7 TEST RESULTS........................................................................................23 4.5 POWER SPECTRAL DENSITY MEASUREMENT....................................26 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT..................26 4.5.2 TEST INSTRUMENTS..............................................................................26 4.5.3 TEST PROCEDURE.................................................................................26 4.5.4 DEVIATION FROM TEST STANDARD.....................................................26 4.5.5 TEST SETUP ...........................................................................................26 4.5.6 EUT OPERATING CONDITION................................................................26 Report No.: RF960125A06 3 Report Format Version 2.0.5 4.5.7 TEST RESULTS........................................................................................27 4.6 BAND EDGES MEASUREMENT..............................................................29 4.6.1 LIMITS OF BAND EDGES MEASUREMENT............................................29 4.6.2 TEST INSTRUMENTS..............................................................................29 4.6.3 TEST PROCEDURE.................................................................................29 4.6.4 DEVIATION FROM TEST STANDARD.....................................................29 4.6.5 EUT OPERATING CONDITION................................................................29 4.6.6 TEST RESULTS........................................................................................30 4.7 ANTENNA REQUIREMENT......................................................................34 4.7.1 STANDARD APPLICABLE.....................................................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST