EMJMMG303MoGo X54 Express Card Mouse

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IC Statement Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device.

Date: November 2, 2007 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request FCC ID: EMJMMG303 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

Power of Attorney Date: November 2, 2007 To whom it may concern: We, the undersigned PRIMAX ELECTRONICS LTD. hereby authorize Advance Data Technology Corporation (ADT) of Taiwan to act on our behalf in all matters relating to all processes required in the FCC Part 15C approval and any communication needed with the national authority. Any and all acts carried out by ADT on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT Model: MG303 Page 2 Model: MG304

FCC ID: EMJMMG303 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Label

Page 3 Model: MG303 Page 4 Page 5 Page 6 Page 7 Page 8 Model: MG304 Page 9 Page 10 Page 11 Page 12

FCC ID: EMJMMG303 Report No.: RF960907A03 Operational Description The device is a Frequency Hopping device with 79 hopping frequencies. The antenna type is Printed Antenna and there is no antenna connector used. The EUT is a unit that contains a Bluetooth radio module. Bluetooth is a short-range wireless technology operating in the 2.4GHz band. It enables devices to have the ability to form networks and exchange information. The other instruction, please have a look at the user’s manual.

Report No: SA960907A03 1 RF EXPOSURE REPORT REPORT NO.: SA960907A03 MODEL NO.: MG303, MG304 ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT : PRIMAX ELECTRONICS LTD. ADDRESS : No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY : Advance Data Technology Corporation LAB ADDRESS : No. 47, 14 th Ling, Chia Pau Tsuen, Linko Hsiang 244, Taipei Hsien, Taiwan, R.O.C. Report No: SA960907A03 2 Conclusion No Evaluation Required if power is below this threshold: F(GHz) mW Low 2.402 High 2.480 24.58 Maximum measured transmitter power: Pout (dBm) Pout (mW) Conducted Power 0.35 1.084 EIRP Power 0 1.000 *Note: The antenna is Printed antenna with -0.35dBi gain Threshold for no SAR evaluation is 24.58mW Transmitter power is 1.084mW Conclusion: No SAR evaluation required since Transmitter Pout is below FCC threshold

Report No.: RF960907A03 1 Report Format Version 2.0.6 FCC TEST REPORT REPORT NO.: RF960907A03 MODEL NO.: MG303, MG304 RECEIVED: Sep. 7, 2007 TESTED: Sep. 10 ~ 15, 2007 ISSUED: Oct. 31, 2007 APPLICANT: PRIMAX ELECTRONICS LTD. ADDRESS: No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB LOCATION: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. This test report consists of 46 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by TAF, A2LA or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF960907A03 2 Report Format Version 2.0.6 TABLE OF CONTENTS 1. CERTIFICATION..............................................................................................4 2. SUMMARY OF TEST RESULTS .....................................................................5 2.1 MEASUREMENT UNCERTAINTY ...................................................................6 3. GENERAL INFORMATION ..............................................................................7 3.1 GENERAL DESCRIPTION OF EUT ................................................................7 3.2 DESCRIPTION OF TEST MODES ..................................................................8 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST..............................................8 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL...................9 3.3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS................................10 3.3.4 DESCRIPTION OF SUPPORT UNITS ..........................................................10 4. TEST TYPES AND RESULTS ....................................................................... 11 4.1 CONDUCTED EMISSION MEASUREMENT................................................. 11 4.2 RADIATED EMISSION MEASUREMENT...................................................... 11 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT ................................... 11 4.2.2 TEST INSTRUMENTS ...................................................................................12 4.2.3 TEST PROCEDURES ...................................................................................13 4.2.4 DEVIATION FROM TEST STANDARD ..........................................................13 4.2.5 TEST SETUP.................................................................................................14 4.2.6 EUT OPERATING CONDITIONS ..................................................................14 4.2.7 TEST RESULTS ............................................................................................15 4.3 NUMBER OF HOPPING FREQUENCY USED..............................................19 4.3.1 LIMIT OF HOPPING FREQUENCY USED....................................................19 4.3.2 TEST INSTRUMENTS ...................................................................................19 4.3.3 TEST PROCEDURES ...................................................................................19 4.3.4 DEVIATION FROM TEST STANDARD ..........................................................20 4.3.5 TEST SETUP.................................................................................................20 4.3.6 TEST RESULTS ............................................................................................20 4.4 DWELL TIME ON EACH CHANNEL..............................................................22 4.4.1 LIMIT OF DWELL TIME USED......................................................................22 4.4.2 TEST INSTRUMENTS ...................................................................................22 4.4.3 TEST PROCEDURES ...................................................................................22 4.4.4 DEVIATION FROM TEST STANDARD ..........................................................22 4.4.5 TEST SETUP.................................................................................................23 4.4.6 TEST RESULTS ............................................................................................23 4.5 CHANNEL BANDWIDTH...............................................................................27 4.5.1 LIMITS OF CHANNEL BANDWIDTH.............................................................27 4.5.2 TEST INSTRUMENTS ...................................................................................27 4.5.3 TEST PROCEDURE ......................................................................................27 4.5.4 DEVIATION FROM TEST STANDARD ..........................................................28 4.5.5 TEST SETUP.................................................................................................28 4.5.6 EUT OPERATING CONDITION.....................................................................28 4.5.7 TEST RESULTS ............................................................................................28 4.6 HOPPING CHANNEL SEPARATION.............................................................31 4.6.1 LIMIT OF HOPPING CHANNEL SEPARATION.............................................31 Report No.: RF960907A03 3 Report Format Version 2.0.6 4.6.2 TEST INSTRUMENTS ...................................................................................31 4.6.3 TEST PROCEDURES ...................................................................................31 4.6.4 DEVIATION FROM TEST STANDARD ..........................................................32 4.6.5 TEST SETUP.................................................................................................32 4.6.6 TEST RESULTS ............................................................................................32 4.7 MAXIMUM PEAK OUTPUT POWER ......................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST