EMJMMOBTE7ULBluetooth Laser Mouse

Kiwi BT Laser Mouse User’s Guide Model No :MOBTE7UL Rating: 3V DC 40mA Made in China Introduction Package Contents ∑ AAA Battery x 2 pc ∑ User’s Guide x 1 System Requirements ∑ Pentium processor or equivalent ∑ At least one USB port (USB 2.0 or 1.1) ∑ Operating System: Windows ® XP with Service Pack 1 or higher, Windows ® Vista, Windows ® 7 Feature Kiwi BT is Bluetooth Laser Mouse in middle size with magnetic battery cover, is equipped with Laser-based Soc Sensor 7630 from Avago that’s empowered by Bluetooth 2.1 Technology and a changeable 1000DPI/1500DPI, and using OFM A320 sensor for 4-way scrolling controls. It also provides a low battery indicator on top of the mouse to warning user for battery change. Function Introduction 1. Left Button 2. Right Button 3. Touch-Sensitive Scrolling 4. Windows 7 Task Switching 5. Gesture button 6. Power and DPI LED. 7. Bluetooth pairing button and LED Indication 8. Power On/Off Pairing introduction The Bluetooth connection indication and LED indication is defined as below: A dual-color, blue and white, LED is used to indicate the status of power and Bluetooth connection, present DPI, including the power on and off state, low-power alert, Bluetooth pairing, Bluetooth reconnecting. The power detection is defined as three levels: A: Power is sufficient: voltage level is higher than 2.2 volt; LED will be on in the color upon present DPI setting, and then be off in 2 seconds. B: power is low: voltage level is lower than 2.2 volt, but higher than 2.05 volt; LED will be on in the color upon present DPI setting, and then be blinking once every one second, lasting for 1 minute. C: Power is off: voltage level is lower than 2.05 volt; mouse power is cut off and LED is not turned on The Bluetooth connection indication is defined as below: In pairing mode: blue LED starts blinking once every one second, lasting for 2 minutes. AS long as KIWI BT is successfully paired with the computer, blue LED will be turned off. KIWI checks the battery status and enables the LED indication: A: battery status change in active mode B: mouse is waked up from sleeping mode or standby mode C: power is manually turned on and off by the sliding switch Regulatory Compliance Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement: The product comply with the US/Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or reduce output power if it doesn't affect the transmission/receiving quality. IC Statement Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device. Eye safety This product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Date: April 15, 2011 Federal Communications Commission Authorization and Evaluation Division Declaration letter for label requirement FCC ID: EMJMMOBTE7UL The label is permanent affixed inside the battery cover, and the EUT will be selling to market without the battery installed. The users can see the label during the battery installation process. The battery cover can be opened without any special tools. Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Date: April 15, 2011 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request FCC ID: EMJMMOBTE7UL Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Power of Attorney Date: April 15, 2011 To whom it may concern: We, the undersigned PRIMAX ELECTRONICS LTD. hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan Branch) of Taiwan to act on our behalf in all matters relating to all processes required in the FCC Part 15C approval and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan Branch on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, -------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT

LABEL LOCATION Label

Page 2 Page 3 Page 4 Page 5

FCC ID: EMJMMOBTE7UL Report No.: RF110328D06 Operational Description The device is a Frequency Hopping device with 79 hopping frequencies. The antenna type is Printed antenna and there is no antenna connector used. The EUT is a unit that contains a Bluetooth radio module. Bluetooth is a short-range wireless technology operating in the 2.4GHz band. It enables devices to have the ability to form networks and exchange information. The other instruction, please have a look at the user’s manual.

Report No: SA110328D06 1 Report Format Version 4.0.0 RF EXPOSURE REPORT REPORT NO.: SA110328D06 MODEL NO.: MOBTE7UL, MS12 FCC ID: EMJMMOBTE7UL ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT : PRIMAX ELECTRONICS LTD. ADDRESS : No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY : Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS : No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien, 244 Taiwan Report No: SA110328D06 2 Report Format Version 4.0.0 Conclusion No Evaluation Required if power is below this threshold: F(GHz) mW Low 2.402 High 2.480 24.58 Maximum measured transmitter power: Pout (dBm) Pout (mW) Conducted Power -1.1 0.8 EIRP Power -6.9 0.2 *Note: The antenna is Printed antenna with -5.81dBi gain Threshold for no SAR evaluation is 24.58mW Transmitter power is 0.8mW Conclusion: No SAR evaluation required since Transmitter Pout is below FCC threshold ---END---

Report No.: RF110328D06 1 Report Format Version 4.0.0 FCC TEST REPORT REPORT NO.: RF110328D06 MODEL NO.: MOBTE7UL, MS12 FCC ID: EMJMMOBTE7UL RECEIVED: Mar. 28, 2011 TESTED: Apr. 1 ~ 6, 2011 ISSUED: Apr. 14, 2011 APPLICANT: PRIMAX ELECTRONICS LTD. ADDRESS: No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB LOCATION: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien, 244 Taiwan This test report consists of 41 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF110328D06 2 Report Format Version 4.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD................................................................................4 1. CERTIFICATION........................................................................................5 2. SUMMARY OF TEST RESULTS...............................................................6 2.1 MEASUREMENT UNCERTAINTY.............................................................7 3. GENERAL INFORMATION........................................................................8 3.1 GENERAL DESCRIPTION OF EUT..........................................................8 3.2 DESCRIPTION OF TEST MODES............................................................9 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST........................................9 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL...........10 3.3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS..........................11 3.3.4 DESCRIPTION OF SUPPORT UNITS.....................................................11 4. TEST TYPES AND RESULTS..................................................................12 4.1 CONDUCTED EMISSION MEASUREMENT...........................................12 4.2 RADIATED EMISSION MEASUREMENT................................................12 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT.............................12 4.2.2 TEST INSTRUMENTS.............................................................................13 4.2.3 TEST PROCEDURES.............................................................................14 4.2.4 DEVIATION FROM TEST STANDARD....................................................14 4.2.5 TEST SETUP...........................................................................................15 4.2.6 EUT OPERATING CONDITIONS.............................................................15 4.2.7 TEST RESULTS......................................................................................16 4.3 NUMBER OF HOPPING FREQUENCY USED........................................21 4.3.1 LIMIT OF HOPPING FREQUENCY USED..............................................21 4.3.2 TEST INSTRUMENTS.............................................................................21 4.3.3 TEST PROCEDURES.............................................................................21 4.3.4 DEVIATION FROM TEST STANDARD....................................................22 4.3.5 TEST SETUP...........................................................................................22 4.3.6 TEST RESULTS......................................................................................22 4.4 DWELL TIME ON EACH CHANNEL........................................................24 4.4.1 LIMIT OF DWELL TIME USED................................................................24 4.4.2 TEST INSTRUMENTS.............................................................................24 4.4.3 TEST PROCEDURES.............................................................................24 4.4.4 DEVIATION FROM TEST STANDARD....................................................24 4.4.5 TEST SETUP...........................................................................................25 4.4.6 TEST RESULTS......................................................................................25 4.5 CHANNEL BANDWIDTH.........................................................................27 4.5 CHANNEL BANDWIDTH.........................................................................27 4.5.1 LIMITS OF CHANNEL BANDWIDTH.......................................................27 4.5.2 TEST INSTRUMENTS.............................................................................27 4.5.3 TEST PROCEDURE................................................................................27 4.5.4 DEVIATION FROM TEST STANDARD....................................................28 4.5.5 TEST SETUP...........................................................................................28 4.5.6 EUT OPERATING CONDITION...............................................................28 4.5.7 TEST RESULTS......................................................................................29 Report No.: RF110328D06 3 Report Format Version 4.0.0 4.6 HOPPING CHANNEL SEPARATION.......................................................30 4.6.1 LIMIT OF HOPPING CHANNEL SEPARATION.......................................30 4.6.2 TEST INSTRUMENTS.............................................................................30 4.6.3 TEST PROCEDURES.............................................................................30 4.6.4 DEVIATION FROM TEST STANDARD....................................................30 4.6.5 TEST SETUP...........................................................................................30 4.6.6 TEST RESULTS......................................................................................31 4.7 MAXIMUM PEAK OUTPUT POWER.......................................................32 4.7.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT........32…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST